Search Documents

By L. Nahai

An important objective of the Australian Government's policies on resources development is to encourage further processing of raw materials domestically, to the extent that this is economically feasible and consistent with sound industrial development. This Bureau of Mines report examines the extent to which Australia is able to pursue this policy in terms of its own competitive advantages and the implications of such a policy for the United States. Such factors as the impact of other competing producers and their advantages, expected world demand, and infrastructural problem--which may limit pursuit of this policy to the fullest extent--are discussed. After a broad review of the re-source, economic, social, and environmental factors, the perspective for increased processing is examined for a number of mineral commodities.

Jan 1, 1982

By I. Liebman

The Bureau of Mines conducted research to develop triggered barrier systems for protection against gas explosions that can occur in underground coal mines during the use of continuous miners. Several extinguishing agents were tested in barriers at a simulated mine face. Water, powered by pressurized nitrogen, was found to be efficient in stopping fully developed gas explosions, but it had little effect against the explosion during its incipient stage. Hybrid combinations of currently known extinguishants, however, were successful against incipient explosions. Three hybrids that were developed and tested consisted of Halon 1301, combined with either an aqueous foam solution, water, or a dry chemical powder. The three hybrids were found to be more efficient than any constituent alone. Results of the tests point to a synergism between the hybrid components, and indicate that the Halon aids in dispersing its constituent and also converts the aqueous foam solution into a stable fine foam and the water into fine drops.

Jan 1, 1978

By Todd M. Ruff

This report summarizes ongoing research at the National Institute for Occupational Safety and Health, Spokane Research Laboratory, in which collision warning systems for surface mining dump trucks are being evaluated. Common accidents involve these large trucks running over smaller vehicles or pedestrian workers. Collision warning systems currently use one of several methods, including radar, radio-frequency-signal detection, or ultrasonic signals, to detect and warn of the presence of an object or person in the blind spots of the mining equipment. Most available systems have not been tested on large off-highway dump trucks. This report evaluates several systems on two sizes of trucks, a 50-ton-capacity truck commonly used in quarries and construction and a 240-ton-capacity truck commonly used in open-pit mines. Tests were conducted to determine false alarm rates, alarm effectiveness, and reliable detection zones for a person and a pickup truck. The results indicate that radar and radio-frequency identification systems show promise for this application and that several of the improved systems are ready for extensive field tests. However, challenges still exist in applying these technologies to large trucks.

Jan 11, 2000

By J. J. Forbes

The activities of the Bureau of Mines include the development and testing of self-contained oxygen breathing apparatus and other devices for respiratory protection, the development and tasting of devices for detecting dangerous or noxious mine atmospheres, and the training of men in the mineral industries in the use and care of this equipment to enable them to render effective service in mine rescue and recovery operations following mine fires and explosions, or under other conditions where irrespirable gases may be found in mines or mining plants. The first use of self-contained oxygen breathing apparatus for com- bating mine fires and explosions in the United States dates back about 30 years. Previous to that time, exploration for any distance ahead of fresh air was virtually impossible without great risk to life; moreover, the men called upon to render service at mine disasters were not well-versed in the properties and physiological effects of gases likely to be encountered. It was also impossible to work ahead of fresh air to restore ventilation, and if many stoppings were blown out by an explosion, air had to be introduced into whole areas or sections at once without knowledge of the conditions ahead; moving an explosive mixture of methane and air over live fire had to

Jan 1, 1938

By Russell R. McLellan

As part of an effort to develop new or improved placer mining technology in the Tertiary gold-bearing channel gravel of northern California, the Bureau of Mines conducted investigations at the old Badger Hill placer mine in Nevada County, Calif., to collect data and information regarding drilling and sampling methods and deposit characteristics. Sampling studies involved the collection and processing of 400 tons of large-and small-volume samples from drill holes, underground workings, surface pits, and blasthole rounds. A total of 355 samples averaging 2,296 pounds per sample provided reasonably accurate data for analysis of the gold distribution. These studies indicated that the bulk of the gold is within 40 feet of bedrock in stacked, lenticular zones of cemented gravel that are largely confined to the relatively narrow, meandering course of the deepest portion of the bedrock channel. Drilling studies involved the testing of truck-mounted rotary, buckett and vibratory drills, none of which proved to be a completely versatile tool for sampling quickly and reliably both consolidated and unconsolidated gravel..

Jan 1, 1974

By George S. Rice

[This paper gives the details of tests to determine the design of stoppings capable of withstanding a pressure, applied to either side, of 50 pounds per square inch,6 as required by section 104 (a) of the Operating Regulations to Govern Coal-Mining Methods on Leased Lands on the Public Domain, issued in 1921 and quoted oil page 3. The regulations stipulated that the design for such stoppings must lie approved by the United States Bureau of Standards. The engineers of that organization felt that knowledge of the strength of such structures with respect to the effect of explosion pressure in comparison with static pressure and the strength of the walls which furnish the abutments was insufficient to justify drafting specifications; therefore, tests were needed to give information upon which a rational system of design could be based. A study was then begun; and several series of tests, made by the United States Bureau of Mines and the United States Bureau of Standards in cooperation, grave information upon which are based the detailed specifications offered in a later section. Slabs representing concrete stoppings, with and without reinforcement, were tested at the Bureau of Standards in Washington D. C.; afterwards, full-scale stoppings were tested at the Bureau of Mines Experimental mine near Pittsburgh. It was assumed that in most coal mines the strength of the floor and roof could not be relied on, but dependence must be placed upon the strength of the coal ribs. The tests developed that the maximum strength of an unreinforced concrete stopping was obtained when it acted as a flat arch buttressed against the coil ribs; but its ultimate strength depended upon the resistance to movement offered by the coal strata against which its ends were restrained or buttressed.]

Jan 1, 1931

By D. Harrington

Probably over 95 percent of the coal production of the United States depends upon the use of explosives before it can be placed in the railroad car at the mine, and up to the present time it has been impossible to obtain Pry kind of practicable explosive that isn't dangerous unless handled carefully. In other words, no "foolproof" explosives have been found to date and inspection of the accident records of the coal mines of this country indicates that the use of explosives in coal mines has taken a sad toll of lives. ACCIDENTS PROM EXPLOSIVES IN COAL MATES Of the 2,000 to 2,500 persons killed annually in the coal mines if the United States, 100 to 125 have been killed from explosives without an explosion of gas or dust; these accidents have been due to misfires, hangfires, premature blasts, or accidental setting off of explosives through carelessness or otherwise (but chiefly through carelessness in some form). In this type of accident the flame character of the explosive is not necessarily involved, although an unexpected or premature blast is initiated much more easily with black blasting powder, which has a long flame, than with a permissible explosive, which has a flame much shorter and of briefer duration. By far the greater number of such accidents are caused by black blasting powder or dynamite rather than by permissible explosive.

Jan 1, 1936

By J. T. McCartney

OPTICAL PROPERTIES of U.S. coals of differing rank have been investigated by the Bureau of Mines, for about 20 years. These investigations have been remade to further the development of an objective basis for petrographic analysis of coal and to add to knowledge of the structure and composition of coal and coal components by determining their optical constants in various regions of the electromagnetic spectrum. Various experimental techniques have been used in these studies, including determination of reflectance from bulk specimens and transmittance of thin and ultrathin sections, interferometry, electron microscopy, and election diffraction. Similar studies leave also been made of graphite, the end product of coal metamorphism. The bureau of Mines conducted the first U.S. investigation of reflectance properties of coal components, laying the foundation for petrographic analysis based on arbitrary reflectance classes and for automated reflectance analysis of coals. Optical constants of coals of differing rank and of graphite have been determined in the ultraviolet-visible-near infrared spectrum. Maxima in the optical constants of graphite were observed in the ultraviolet region and were interpreted to be related to transitions of electrons between the valence and conduction bands. Similar maxima for coals, especially high-rank coals, appeared to be characteristic of the presence of graphitelike layers. A special application of optical theory to absorbing, anisotropic materials like graphite and high-rank coals has been developed. Electron microscopic and electron diffraction studies of coals have revealed various ultrafine structures in coal components and have shown the evolution of an oriented, crystalline graphite structure in high-rank coals.

Jan 1, 1967

By J. M. Gomes

Bench-scale flotation tests were conducted on two western tactite ores to study the recovery of tungsten and zinc minerals. The investigation, which is part of the Bureau of Mines ongoing program to develop methods for beneficiating minerals and metals from domestic low-grade ores, demonstrated the feasibility of producing scheelite, sphalerite, and their bulk concentrates. Sphalerite concentrates containing 51 to 53 pet Zn and less than 0.11 pct W03 were selectively recovered prior to scheelite flotation. Zinc recovery ranged from 85 to 91 pct. Scheelite concentrates containing 17 to 25 pct W03 were then recovered from the ore; tungsten recoveries ranged from 88 to 94 pct. Bulk flotation concentrates containing 84 to 91 pct of the W03 and 87 to 95 pct of the zinc also were prepared. More than 98 pct of the W03 in a bulk concentrate containing 9 pct W03 was extracted by autoclave leaching with a soda solution. The zinc remained in the leached residue.

Jan 1, 1982

By V. A. Cammarota

In this report, the effects of anode-production variables, such as aggregate coke sizes, pitch binder content, and baking cycle, were investigated. A small alumina reduction cell proved effective in evaluating anodes prepared from commercial materials and from lignite coke and pitch. Compressive strength was found to be the physical property most significantly influenced, but it did not appear to affect anode consumption. Specific carbon consumption, that is, the ratio of carbon in the anodic gas to carbon theoretically oxidized at the anode, was used as an index of anode consumption. It was found that an anode made with lignite coke and commercial pitch was very low in consumption; however, anodes made completely from lignite but by a different fabrication method showed high consumption and anode deterioration. Microscopic examination of anodes after electrolysis showed evidence of higher consumption at low current densities, and was useful in judging overall anode quality. Based on the physical properties of the anodes and their consumption during electrolysis, lignite can be a suitable material for anodes, provided the proper fabrication conditions are used.

Jan 1, 1970

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world output for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963

By B. T. Brady

Recent theoretical, experimental, and field studies conducted by the Bureau of Mines suggest that rock failures may be predicted and, in some instances, controlled. Theoretical studies that were later corroborated by laboratory and field studies predict that a seismic anomaly will precede rock bursts and/or roof falls in mines. The seismic anomaly is predicted to consist of an increase in the number of seismic events occurring in the immediate vicinity where the failure 1s nucleated. This increase will then be followed by a dramatic decrease of seismicity in a broad region that surrounds the location of the impending failure. The dimensions of this region allow a preliminary estimate of the time to failure (measured from the time the seismicity increase began) as well as an estimate of the energy that will be released at the instant of failure. Field observations indicating that this predicted behavior does precede rock bursts and a roof fall are presented in this report. Implications of results to the problem of failure control in mines that experience massive rock failures are discussed.

Jan 1, 1978

By R. R. Falier, W. E. Rice

"PURPOSE OF REPORTThis paper presents the results of a series of tests made by the U. S. Bureau of Mines in cooperation with The Ohio State University Engineering Experiment Station as part of an investigation on the use of fuel in kilns.This report is preliminary and gives only enough of the test data to illustrate results and show the reasons for the successes and failures of the method of firing investigated; fuller details will be included in the final report.PERSONNEL FOR TESTSThe investigation is conducted under supervision of P. Nicholls, supervising fuel engineer, of the United States Bureau of Mines, and G. A. Bole, research professor, of The Ohio State University. These tests were made under direction of W. E. Rice, associate fuel engineer, assisted by R. R. Faller, assistant fuel engineer, of the United States Bureau of Mines; H. C. Harrison, senior research engineer (until October 1, 1930), C. R. Austin, senior research engineer (since October 1, 1930), and H. K. Van Sohoick, junior research engineer, of The Ohio State University. M. J. Rice, field engineer, represented the manufacturer of the stoker.PURPOSE OF INVESTIGATIONThe general aim of the investigation is to develop more economical methods of using fuel in kilns and to improve the over—all efficiency of the process of firing by methods that will produce ware of better quality. One phase of this investigation is the burning of coal on an automatic stoker to gain the advantages of control, constant rate of application of heat, and ability to burn cheaper coal than can be used in the hand—fired furnaces of kilns. It a stoker in to be used it is desirable that the coot of the installation should be low, the control of operation simple, and the distribution of heat in the kiln as good or better than with hand firing. These desiderata were sought in the stoker and furnaces that were used for the tests described herein. The tests were made to determine whether it is feasible to fire a large kiln with a single stoker, whether the use of a single furnace simplifies control, and whether the admission of all the hot gam at the center of the kiln will give symmetrical distribution of heat."

Aug 1, 1931

By J. M. Singer

In this Bureau of Mines study coal and rock dust beds were entrained by airblasts generated by gas explosions at the closed end of a 0.61-m-diameter explosion tunnel, 49.7 m long. The system was designed to simulate entrainment of mine dust deposits by accidental gas explosion at the coal face of nonintersecting mine passageways. Full-scale mine explosion trials confirmed many of the results of the explosion tunnel experiments and indicated several new features of dust entrainment. Dispersal of 20.3-cm-long stepped dust beds located 35 m from the closed end always began during the early portion of the ascending gradient of the first transient airflow (and pressure) wave, and was usually completed before the end of the first quarter-wave period. Bulk quantities of dust were entrained simultaneously by longitudinal regression from the leading edge of the dust bed and by surface lifting of the top layer. Instantaneous threshold air velocities for bulk quantities of coal and rock dust beds in separate, mixed, and layered configurations were in the same range (5 to 30 m/sec) as previously found under steady-state velocity conditions. Selective lifting of coal dust layers from rock dust occurred when the threshold dispersal velocity of coal dust but not of the underlying rock dust was exceeded.

Jan 1, 1976

The Bureau of Mines conducted large-scale laboratory copper ore leaching tests to enable improving copper recovery from large dump-leaching operations. This was done by comparing leaching progress when copper was recovered from recycled leach liquor either by cementation or by solvent extraction. Copper was leached from 7-ton ore samples at room temperature using pH 2 ferric sulfate solutions. With are samples containing 11 percent minus 0.5-inch fines, no marked advantage in using either of the copper recovery methods was evident after 416 days of leaching. With ore containing 32 percent minus 0.5-inch fines, solvent extraction of copper was advantageous in that 60 percent of the copper was extracted after 568 days, whereas only 48 percent of the copper was extracted when cementation was used. Less acid was consumed during leaching when solvent extraction, rather than cementation, was used for copper recovery. Iron, contributed by cementation with scrap iron, plugged the ore bed containing 32 percent fines.

Jan 1, 1981

By B. K. Shibler

During a research program to develop improved methods for recovering elemental sulfur and useful sulfur compounds from secondary source materials, the technical literature was searched for pertinent articles on processing methods. This report summarizes results of the literature survey and describes the more important processes that have been used or suggested for recovering sulfur and sulfur compounds from all non-Frasch sources. The bibliography presented represents a survey of the available English language literature on the subject through 1958, with particular attention focused on the period 1950 through 1958. Engineering Index and Industrial Arts Index were the principal guides used in the survey of this period. Chemical Abstracts was used to a limited extent to identify a few key foreign articles and patents. The Sulfur Symposium (4)4 published in November 1950 by Industrial and Engineering Chemistry includes a broadly representative selection of the literature up to 1949. Therefore, this reference was used extensively to locate and list pertinent articles on processing methods reported in the period prior to 1950.

Jan 1, 1962

By Adam K. Smith

Occupational hearing loss is a permanent illness with no recovery currently possible. For underground coal mine workers, Noise Induced Hearing Loss (NIHL) continues to be a serious health issue. One of the principal and fundamental machines used in underground mining operations is also one of the loudest. Noise generated on the continuous mining machine is the result of 3 operational components: the cutting system, the dust collection system, and the onboard conveying system. During underground acoustic evaluations, the conveyor system noise was observed to be dominant. In order to more closely examine sound generated by the continuous mining machine, sound power levels were measured in a reverberation chamber at the Pittsburgh Research Laboratory (PRL). Different chain types and configurations were installed on the conveyor system, and the resulting sound power level ranged from 118 dB(A) to 108 dB(A). Noise generated by the dust collection system was also examined and found to be 107 dB(A).

Jan 1, 2008

By Sam S. Taylor

Disposal of brines produced with crude petroleum and natural gas is a continually increasing problem. The necessity for studying this problem has been realized more generally in recent years, and in August 1934 an agreement was made between the Kansas State Board of Health and the United States Bureau of Mines to conduct a cooperative technical study of methods of brine disposal. To date one paper in the technical press4/ and three reports5/6/ have been published in which are given results of studies carried on under this cooperative agreement. In the Mid-Continent fields, the methods used most generally for handling oil-field brines are: (1) Impounding in evaporation ponds; (2) controlled diversion into surface streams; and (3) injection into subsurface formations through wells assigned for this purpose. Various States recognize one or more of the methods as legally authorized procedure. Impounding brine in ponds and solar evaporation have proved inadequate as a general rule, owing, usually, to the porous nature of the soil, the low rate of evaporation, or both. Diversion, of

Jan 1, 1937

By Sam S. Taylor

Disposal of brines produced with crude petroleum and natural gas is a continually increasing problem. The necessity for studying this problem has been realized more generally in recent years, and in August 1934 an agreement was made between the Kansas State Board of Health and the United States Bureau of Mines to conduct a cooperative technical study of methods of brine disposal. To date one paper in the technical press4/ and three reports5/6/ 7/ have been published in which are given results of studies carried on under this cooperative agreement. In the Mid-Continent fields, the methods used most generally for handling oil-field brines are: (1) Impounding in evaporation ponds; (2) controlled diversion into surface streams; and (3) injection into subsurface formations through wells assigned for this purpose. Various States recognize one or more of the methods as legally authorized procedure. Impounding brine in ponds and solar evaporation have proved inadequate as a general rule, owing, usually, to the porous nature of the soil, the low rate of evaporation, or both. Diversion of

Jan 1, 1937

By G. C. Lammers

The object of this study was to determine the economic feasibility of hydraulically transporting Sandow (Tex.) lignite 100 miles and dewatering and thermally drying the transported lignite to a surface-dry condition. The most important factors involved in the feasibility of hydraulic transport, are the degradation incurred during transit, the length of the line, and the cost of alternative methods of shipment. In pipeline tests in which roughly 75 miles of hydraulic transport was simulated the percentage of minus-325-mesh solids increased from about 1 to 41 percent for both lignite and bituminous coal; in the micron sizes the coal fared considerably better than the lignite. Such degradation, even though it enhances flow through the pipe-line, severely aggravates the dewatering problem on lignite. Cost studies indicated that continuous vacuum filters offer the most economical means of dewatering minus-1/8-inch material. Surface moisture, if high, must be removed by relatively expensive thermal drying.

Jan 1, 1958