Search Documents

By Gloria Contreras

The study aims to optimize the density of holes per tunnel section. The energy distribution, the one with the highest density, is used in the center of the diagram and is distributed homogeneously towards the contours with the lowest energies up to the contours to produce a perimeter control.

Feb 1, 2020

By D Maxwell Ellett

This report presents an evaluation of knowledge concerning a process used in predicting ground motion resulting from large scale conventional explosive detonations, The shots were set off in Arizona in connection with copper ore recovery activities.

Jan 1, 1976

By Mauritz Kotze, Jason Furtney, Ewan Sellers, Sandy Etchells, Tom Szendrei

The development of a simple model for gas flow and burden movement has driven the need to improve our understanding of burden breakage mechanisms for single hole blasts and the interaction between multiple holes in solid and jointed rock masses. Conventional analytical understandings of the burden breakout using the elastic-tensile fracture model were studied and found to provide a breakout angle that is independent of burden in contradiction to experimental data. By considering rock fracture in terms of Mohr-Coulomb plasticity using analytical expressions from the field of cavity expansion analysis an improved relationship between breakout angle and burden is derived until the point of critical breakout at which the angle of breakout suddenly changes from between 90 degree and 100 degrees to zero. This suggests that the critical burden occurs at about 0.6 times the radial fracture zone calculated from the analytical solutions.

Jan 1, 2013

By Paul Worsey, Braden Lusk, Seokbin Lim

This paper discusses the theory and experiment involved in the discovery of the mechanisms of Linear Shaped Charges, which are much different from those for Conical Shaped Charges. Linear Shaped Charges (LSC) have been assumed to function in the same manner as Conical Shaped Charges (CSC) in the published literature on the subject. Much work has been done on CSC for military purposes, but there is limited information about the mechanics of LSC. Previous theories have cited the formation of a Monroe Jet as the dominant process. The Monroe Effect describes what happens to a target below the charge following detonation of the charge, and prescribes a fluid jet process for penetration. The fluid jet comprised of the liner material is the cutting device in CSC and has been extensively studied. Recent work at the University of Missouri at Rolla (UMR) cutting concrete with LSC has surprisingly shown that there is not a fluid jet process in LSC. After completing several reinforced concrete penetration tests, minimally deformed copper blades were found in the debris. Initially, the blades were suspected to be misfires or malfunctioned charge remnants. However, results were good and blades were found after every single test. Upon closer inspection, the ribbons were found to be folded copper and they were suspected to be the bottom liner of the LSC. A test series was conducted to verify the new theory by experiment.

Jan 1, 2005

By Yessica Idrogo

"Undoubtedly mining is currently the activity that brings a great development for all countries involvedin this industry, which means that to develop mining requires adequate explosive mixtures. The following work about AL/AN/FO is presented, knowing that this is a dry blasting agent, which iscomposed by ammonium nitrate, petroleum diesel N°2 and aluminum (AN, FO, AL). It is known that this dry blasting agent AL/AN/FO was invented by A. Baver Ph. D. in Marcona Mining Company, 12/12/1968, where in that investigation also worked Carlos Agreda Ph.D. as assistant of the mentioned inventor."

Jan 1, 2017

By Eric C. Gerst

"In this current era of soft commodity and coal prices the mining industry is turning towards optimizingall levels of production to reduce operating costs. Part of this trend includes the automation of miningmachines. As the first tier of the mining process blast hole drill automation offers benefits through the entire value stream from drill bench to material processing."

Jan 1, 2017

By Wayne Rogers, Sarma Kanchibotla, Alan Tordoir, Bryon Bisiauz, Seth Ako, Eric Engmann

Blast induced rock mass displacement can have a significant impact on ore loss & dilution. The mischaracterization of the grade boundaries both prior to, as well as a result of blasting can lead to significant financial losses on account of ore loss and dilution. Ore dilution occurs when waste material is miscategorised as ore and sent for processing diluting the run of mine head grade and recovery. Ore loss takes place when valuable mineral is miscategorised as waste and sent to the waste dumps, thus never being processed and recovered.

Jan 1, 2012

By Jeffrey W. Lin, Jonathan D. Abbott, Patrick R. Bowden, Tyson J. Plitt

Pentolite is a class of high explosives containing trinitrotoluene (TNT) and pentaerythritol tetranitrate (PETN) with PETN content typically ranging from 40 to 60 wt%. Manufacture involves melting TNT, 80 °C, followed by addition of PETN and trace ingredients to form a homogeneous mixture. Once a mix is ready to be poured, several factors can influence the behavior of the finished product including how long the mix has been at temperature and cooling rate. After the manufacturing process has been completed, storage conditions combined with manufacturing conditions may cause physical changes. Two such changes explored were exudation, liquid exuding from solid boosters, and ratchet growth, irreversible volumetric expansion. Exudation is principally caused by excess water in the process. Ratchet growth is a common phenomenon of nitroaromatic compounds such as TNT where time and temperature fluctuations can cause materials to increase volume, simultaneously decreasing density. Although neither phenomenon affects common attributes such as sensitivity, performance, and shelf-life, both can cause issues in storage and handling. In this study pentolite was cast into various forms under different manufacturing conditions and evaluated over several months of controlled storage conditions including ambient, temperature cycling and elevated isothermal. Subjective and objective measurements were made throughout the evaluation period with the aim to determine the preferred storage methodology.

Jan 21, 2025

By Armin Iravani, Changping Yi, Matthias Wimmer, Daniel Johansson, Santiago Gómez, Håkan Schunnesson

Sublevel caving (SLC) is a mass mining method based upon the utilization of gravity flow of blasted ore and caved waste rock. Drilling and blasting are the initial and the major impact on primary fragmentation and later material flow characteristics. The heterogeneity of rock mass has a great impact on materials’ mechanical properties and plays a significant role in rock fragmentation by blasting. In this work, a numerical model for sublevel caving based on 3D Voronoi tessellations was developed to section rock mass into arbitrarily shaped regions for modelling the heterogeneous rock mass. A coupled finite element and discrete element method was employed to investigate both the fragmentation due to blasting and the gravity flow of ore in a heterogeneous orebody. In the coupled model, the caved waste rock was modelled with loose discrete particles while the orebody to be blasted was simulated with bonded particles. The detonation of explosives was described with a particle blast method and a finite element model was used to model the remaining orebody. The results indicated that the fragmentation at the upper part of the ring is coarse while it is fine at the lower part of the ring. The heterogeneity of rock mass induced some boulders after blasting.

Feb 6, 2023

By T. Szendrei, S. Tose

This paper will review several flyrock incidents that occurred recently in the South African mining industry to highlight that potential difficulties of the historical approaches to the problem of flyrock based on correlation studies and regression analysis, including artificial neural networks and similar techniques. These process are not capable of addressing two core issues – root causes of flyrock and projection velocity. A further shortcoming of correlation techniques is that they give no information on the influence of rock size and shape on the flight distance. The scaled depth of burial model for crater blasting in the collar zone and bench face does not specifically address the question of flyrock velocity. A third approach, based on flight trajectory calculations, often neglects the very significant effects of air resistance on the trajectory. Some trajectory models incorporate air resistance but use an implausible fragment velocity model that cannot propel sizeable rocks to distances much beyond 150 m. (Approximately 500 ft.) Nonetheless, trajectory calculation incorporating the effects of air drag affords the most promising approach to the prediction of flyrock range. A unique and insightful feature of the proposed realistic flight modelling is that it collapses all suspected causes of flyrock, many of which are not well understood, to just a single parameter – the launch velocity. This indicates that the root causes of flyrock lie in the mechanisms of momentum transfer to broken rock and suggests new avenues of study for the explosives industry. In this paper we use the trajectory model to identify certain conditions on the bench whereby the impulse of gas pressure acting on fractured material on or close to a free face is enhanced, resulting in a greater transfer of momentum to potential flyrocks.

Jan 1, 2024

By Peter Moser, Michael Messner, Florian Bauer

The existence of ammonia in underground blasting fumes was frequently measured in various field tests (6, 7). Ammonia in fumes with a TLV (threshold limit value) of around 30 ppm (slightly different in various countries) is a toxic gas but not considered to be a high risk for the underground work force as ammonia smells very itching and is extremely annoying. This might be the reason why ammonia is hardly measured in routine underground blasting fumes control. Another reason for the lacking measurement might be the circumstance that ammonia is a very reactive gas and the ammonia sensors available on the market are very cross sensitive to other gases like carbon monoxide. Nevertheless, especially since the introduction of bulk emulsion explosives in underground blasting, complaints from miners about ammonia in the blasting fumes increased. Research work by various institutions [8] around the world relates the ammonia in the fumes back to various mechanisms. Amongst others these comprise: a) non ideal (low temperature) detonation of explosives, with NH3 in the reaction products; b) reaction between rock and non detonated bulk explosives (especially when the rock is of a basic nature (high pH value); c) reaction between shotcrete and non detonated bulk explosives. Numerous blasting tests in an experimental underground set up have been made in order to check these hypotheses for ammonia origin in blasting fumes. None of them has been found to be responsible for sometimes high concentrations of ammonia in the fumes. The major reason for ammonia concentration in blasting fumes has been found in mine water of a high pH value (either natural or from using shotcrete). The mechanism identified is as follows: the moment a non detonated ammonium nitrate bearing explosive comes in contact with mine water of a high pH value, ammonia is formed immediately. The source for the undetonated explosive is twofold: firstly there is a certain spillage of explosives when the holes are charged (especially when using bulk products) and secondly not the entire explosives detonate completely. These undetonated remaining of the explosives end up in the muck pile after blasting. In case there is water of a high pH value the reaction between the explosives and the water starts immediately. This explains also the observation why ammonia can be measured in the blasting fumes quite a long time after the blast. The majority of the ammonia is not formed during the detonation; it is formed inside the muck pile even a considerable long time after the blast.

Jan 1, 2010

By J. P. Proulx, Richard O’Meara, Ruilin Yang

A blast optimization project was carried out at an Open Pit Metal Mine using the Multiple Blasthole Fragmentation (MBF) Model and the Multiple Seed Waveform (MSW) blast vibration model. The aim of the project was to optimize rock fragmentation of the ore blasts to significantly increase metal recoveries while keeping the blast vibration levels at the highwall under control. The project also examined the blasts in the waste rock using the Fragmentation model to expand the blast pattern and select economical explosives for drill and blast cost savings while minimizing any adverse effect on the dig rates. Two sets of near field signature blasthole tests were conducted in both hard ore and relatively soft waste rock. The information from the near-field signature blasthole vibration was used as input to both the MBF and MSW models, as site specific geological information interacting with blasting. The implementation of the full blast design is also input to the MBF and MSW models. A production blast for each rock type was monitored for blast vibration and rock fragmentation. The full blast information and the blast results are used to calibrate and validate the models. The Fragmentation and Vibration model were established for the two rock types at the mine. At each site the Fragmentation modeling was conducted in parallel to the Vibration modeling to ensure blast vibrations were under control while the rock fragmentation was improved. The Fragmentation MBF and MSW are each an integral part of the blast optimization tool. Various scenarios using different explosives, hole delays and blast patterns were modeled for rock fragmentation and blast vibration. The recommendations from the modeling project were to be field trialed at the mine. The implementation of the recommendations was expected to help the mine significantly in terms of the mining economics, and high wall stability and safety.

By C. K. McKenzie

Presents outline of flyrock model and a field procedure to validate predictions of maximum projection distance. Field results are presented from 13 field tests with two different hole diameters.

Feb 1, 2020

By Rajesh Sonkar, Sanjeev Kumar

The deployment of Dragline machines in opencast coal projects involves huge capital expenditure as well as operating costs. The mine operators always endeavor to ensure smooth excavation of material by the Dragline machines while meeting the major objectives of safety, minimal disturbance to environment and optimal operating costs. Optimization of fragmentation through well designed blasts is fundamental in meeting part of the objectives is good fragmentation of rock or mineral proposed to be lifted by the Dragline machine. If the overburden lying over mineral is not properly fragmented, it may result in formation of ‘Toe’ the removal of which is the most arduous task in opencast coal mines. The mine operators always endeavor to achieve best possible results in blasting to ensure smooth operation of the high cost Dragline Machine. However, despite continuous efforts by the blasting engineers involved in bench blasting for the machine, the formation of ‘Toe’ is an ever nagging problem faced in large opencast coal projects eventually reducing the overall operational efficiency of mining.

Jan 1, 2011

By P A. Lang, J G. Ayotte, R W. Humphries

Atomic Energy of Canada Limited (AECL) has the responsibility for research, and development of technologies, for the safe and permanent disposal of Canada's nuclear fuel wastes. As part of this comprehensive program, AECL is constructing an Underground Research Laboratory (URL) near Lac du Bonnet, Manitoba, to evaluate aspects of the concept of waste disposal deep in stable geological formations. No nuclear wastes will be used in the URL program.

Jan 1, 1986

By Jesús V. Saccsa, Kenji B. Loayza, Erick M. Condori, Jorge A. Velásquez

This research investigates how to reduce manufacturing costs of a safety fuse composed of black powder, replacing its ingredient NO3K by NO3Na for processing, and contributing to minimize costs per blasting.

Jan 1, 2017

By Jason Baird, Philip Mulligan

This report details the preliminary calculations governing the underwater collapse of an oil pipe via explosive lensing. An explosive lens changes the detonation wave produced by an explosive by changing the geometric conditions of the explosive (Zukas and Walters, 1998). Multiple lenses can be focused on a central location, generating a series of precise detonation waves collapsing in on a specific point. This report will assume a spherical-shaped, single explosive charge and explain how the authors determined the explosive charge size needed to seal a metal pipe while focusing on one explosive charge acting on part of the pipe. Future calculations will analyze the combination of multiple explosive charges acting on the pipe as a whole.

Jan 1, 2013

By L. Muñoz, L. Steffen, W. Vilas

The emission of particulate material is one of the several parameters related to environmental control in mining operations near communities. Blasting is an event that generates and leaves a large amount of dust in suspension, which can cause discomfort to communities, generating complaints that can compromise the operational continuity of the mine. The proper management of these environmental impacts is a key factor to ensure a good relationship with the neighborhoods, making a responsible mining in harmony with the environment, giving sustainability to the mining business in the medium and long term. The main goal of this work is to present different techniques and technologies applied in a large-scale open pit mine in Brazil, with operations close to a community, to minimize the emissions of particulate material into the atmosphere. For this, different technical solutions were implemented. First, a non-conventional blasting technique was introduced that incorporates special charging and timing configurations, generating a first upper layer that serves as a blanket to contain a second, higher-energy lower layer. An optimal stemming was also defined in order to minimize ejections and maximize cratering, using the scaled depth of burial theory as well as video and fragmentation analysis. In addition, changes were made in the timing between decks (to guarantee a minimum time between layers) and between holes (changing the initiation point opposite to the free face). Finally, additional measures such as humidification of the bench, use of a wind vane to identify wind direction and the construction of a physical barrier between the mine and the community were implemented as additional mitigation measures. By applying the above techniques together, in some specific zones of the mine, it was possible to considerably reduce the ejections generated by blasting versus conventional blasting without the above measures, which was demonstrated in the field with dual blasts trials. Additionally, it was possible to achieve a vibration reduction in the community of ~30%. This work demonstrates how, by applying these technical solutions, it was possible to minimize the dust and vibrations generated by blasting allowing this operation to do sustainable mining

Jan 1, 2024

By D. Johansson, C. San Miguel, U. Stenman, N. Petropoulos

Blasting is a commonly utilized method in civil engineering projects and mining operations. Ammonium nitrate-based (AN-based) explosives are the most efficient explosives today in terms of handling and performance. However, a side effect is the production of gases. The reduction of these gases plays an important role in the safety and environmental aspects in the working place. Therefore, optimizing the recipes of explosives is vital for minimizing the environmental impact and increasing performance. The aim of the project is to provide results and recommendations on the use of emulsion commercial explosives to support the Swedish mining industry and tunnel-contractors as well as the explosives manufactures. The approach was to test various recipes of civil emulsion explosives to investigate the generation of toxic fumes (CO, CO2, NO, NO2 and NOx) during their detonation. To further increase the knowledge of the influence of different additives, ammonium nitrate prills were added in various percentages. The experimental configuration consisted of magnetite mortar cylindrical specimens with a 50 mm borehole at their center, filled with emulsion explosive. Several tests with different emulsion compositions regarding ammonium nitrate additives (10%, 20%, 25%, 30% and 35%) were carried out in a blasting chamber. The measurement equipment was composed of a flue gas analyzer. The instrument was meticulously cleaned after every test, as well as before and during the tests due to condensation (high humidity and dust) at the inlet of the instrument. The emulsion was manually sensitized with microballons and pumped into the cylinders to ensure lack of bubbles, which could introduce inhomogeneities. The acquired gas concentration data was complemented with temperature, humidity, and VoD measurements. The results showed a linear increase of nitrogen gases as the percentage of ammonium nitrate prills increased. On the other hand, carbon gases had a relatively low coefficient of determination. The VoD data showed a behavior that can be described with a simple quadratic equation.

Jan 1, 2024

By Stephen Chung

The quality of a blast design can be evaluated in many ways. It may involve fragmentation, muck profile, environmental effects in terms of vibration and the excavation of the blasted material. To assist and ensure an achievable cost effective design, numerical modeling techniques are often applied as part of the operating procedure. While excavation is one of the mining operations which has a direct influence on the bottom line cost of productivity, the characteristics of a pile of blasted material deserves a closer look in terms of diggability. This paper reviews the current diggability techniques available for application to the blasting operation. To help better understand the involvement in digging, this paper also introduces an evaluation approach based on a discrete element method. The model presented in this paper deals with many variables that are considered to directly affect digging. They are the density and cohesion of material, fragment shape and size distribution as well as the swell of a muck pile. To help visualize the analysis approach, sample runs and animations are given in the paper to show the setup of muck piles produced in bench blasting as well as in sub-level caving. The computed forces experienced by the bucket during each mucking cycle are also discussed.

Jan 1, 2008