Search Documents

By G. B. Harris, A. R. Laplante

Fine tungsten was used to mimic gold and fine and coarse silica and magnetite to mimic gangue. The optimum flow rate of fluidisation water varied from 1.7 l/min for fine silica to 5.6 l/min for coarse magnetite. Overloading at optimum flow rate was then investigated. With fine silica gangue no overload occurred under any of the conditions studied, and there was very little overload with fine magnetite. Coarse silica caused appreciable overload, but only after a significant bed of tungsten had been formed; with fine magnetite gangue the onset of overloading occurred earlier. Finally, with coarse magnetite severe overloading occurred almost immediately. Overloading was modelled using a first-order kinetic rate constant for erosion of the concentrate bed and a critical mass of constant above which it takes place. The results clearly demonstrate the importance of removing oversize to maximise recovery, particularly with a high-density gangue

Jun 18, 1905

By S. Babendererde

The twenty-ninth Sir Julius Wernher memorial lecture of the IMM, presented at Tunnelling '97, London, 2-4 September 1997. The tunnelling industry is well prepared to face the challenge from the population explosion in urban areas in the near future. Many well-established yet redundant concepts are still impeding progress, however, including the prediction of excessive surface ground settlements. The correct selection of TBM can minimise these, and ground deformations can be avoided completely if the appropriate techniques are applied. Advanced techniques have been used in the Tokyo Bay Crossing, where the tunnel lining was installed by robots. Other advanced techniques include the use of a sliding slip form to give temporary support to an extruded tunnel lining, the chemical processing of ground by polymers during earth-pressure balanced tunnelling and the use of electronic monitoring and steering devices in TBMs. There will be challenges to tunnelling in urban environments, as open cut techniques will no longer be tolerated. Two examples of mined stations are briefly discussed

Jun 19, 1905

Two concentrates from Palabora, in South Africa, containing 0.056-0.068% undesirable Cu and 0.8 or 2.2% Ti, were chlorinated with air:chlorine ratios of 10:1, 15:1 and 20:1 at temperatures between 1 200 and 1 329 K. The resulting volatile chlorides were condensed and the solutions analysed for Cu, Fe and Ti. Recovery of Cu was less than 25% at low temperatures and short reaction times, but at 1 258 K almost all Cu was removed from the magnetite at all ratios of chlorine to air. At higher temperatures, the increased carrying over of iron as FeCl3 could be minimised by decreasing the partial pressure of chlorine. No titanium was detected in the volatile products and the percentage of Cu recovered was independent of Ti concentration in the concentrates, though as a function of Cl2 vol%, more Cu was recovered at 1 200 K from the low-Ti than from the high-Ti concentrate. In a fluidised-bed reactor, Cu recovery was 58-90% and iron carry-over less than 10 ppm

Jun 21, 1905

By I. L. Whyte

apparent density and drag coefficient of porous ores on

Apr 1, 1995

By M. J. Beus, B. Stewart, S. Iverson

Ore-pass hazards are a significant safety problem in US underground metal mines. From 1975 to 1995, nearly 75% of injuries during pulling or freeing of ore-pass chutes were related to falls of broken rock or the use of hand tools. Risk assessment methods are being used to identify the most probable causes of ore-pass failures and analyse the factors that result in malfunctioning or safety reduction. Static and dynamic loads are being measured in the laboratory and by field testing, with data from test ore passes compared with mine data to characterise true system behaviour. Computer modelling using closed-form solutions, finite element analysis and a newly developed particle flow code are being use to predict loads from ore and waste flow and impact. Preliminary results indicate that dynamic impacts may be much less than expected, as a result of damping factors, normal and shear stiffness and mass frictional characteristics

Jun 19, 1905

By M. A. Leosson, S. H. Bottrell, R. J. Newton

Sylvite at Boulby is mined 1 140 m beneath the sea and the mine suffers from the influx of water. This is of two kinds: persistent flows originating in the Sherwood Sandstone aquifer and entering the evaporite sequence through fractures in the intervening mudstone, and impersistent flows which are transient in nature and of uncertain origin. Water from the overlying sandstone has become enriched with NaCl and large amounts of KCl and some Mg and Br have been added by interaction with the evaporites. Waters from the transient flows are isotopically distinct from those in the Sherwood Sandstone, being enriched in H and O. They are also saturated with respect to halite and sylvite, but have higher K/Na than the persistent flows and are much more enriched in Mg and Br

Jun 18, 1905

By Hardwick F. W., O'Shea L. T.

The survey covers: coal-mine lighting prior to the invention of the safety-lamp, including candles, the flint-and-steel Spedding mill, and mirrors; the growth in knowledge of firedamp; the Society in Sunderland for Preventing Accidents in Coal Mines; Dr. Clanny's blast lamps and steam lamps; George Stephenson's tube-and-slider lamp, triple-tube lamp, punched-plate lamp and gauze Stephenson lamp; Sir Humphrey Davy's lamps; the controversy over invention priority, and other early forms of safety-lamp; 1816-1835 developments including the lamps of Upton and Roberts, M.Mueseler, John Martin, Dr. Clanny (new 4th lamp), M. Agre, John Newman, Gossart and Roberts, Francis Ellis, John Dillon and Mr. Wood (refrigerating lamp); 1836-1843 developments, notably of Mueseler lamps; 1844-1866, including lamps of the Davy, Clanny, Boty, Eloin and other types; 1867-1879, including the Gray lamp; 1880-1887, including the Marsaut lamp; and 1888-1913. Detailed reference is made to the findings of various relevant Royal Commissions and appendices include a list of the safety-lamps described in an appendix to the 1886 report and a publications list. The paper was prepared for the International congress of mining, metallurgy, applied mechanics and economic geology to have been held in London in July 1915. Discussion (p.718-724) includes a brief comment by Blackett W.C. and a longer contribution by Ashworth J., with the authors' response

Dec 1, 1916

By J. C. Griffiths

There are two kinds of problems concerning the elements of a population : the first is to estimate the proportion of some specific kind of element in the population, e.g. the amount of gold in a block of ground (equals population) or the proportion of mercury in a sample; the second is to estimate the length, breadth, volume, etc., of a specific kind of element, e.g. the grain size of quartz grains in a beach sand or the size, shape and arrangement of lenses of ore in an ore deposit. Given a specific objective, a bounded population, identified elements and the element characteristics of interest, it is then necessary to select a sample of the elements from the population and the problem of sampling requires a decision on how to select the sample. It is also necessary to establish, either by heuristic analysis or empirically, based on long experience, the model frequency distribution of the desired element characteristics: in general, constant-probability models are used as models, the binomial or Poisson for count data and the normal distribution for measurements (or their transformed equivalents). The objective of sampling then becomes to obtain an appropriate statistical estimate of the desired population parameter: for example, the estimators may be the mean (X) and variance (a2): these should be unbiased sufficient estimators of their corresponding parameters (u, a2, respectively). Statistical tests are performed in order to determine that the estimators are of the appropriate kind: all statistical tests are designed to test against bias of a specific kind, although they are stated as tests against randomness. Given a random sample of some population, the estimators are usually stable and adequate to solve the sampling problem. Random samples are simple to define but exceedingly difficult to achieve in practice: in selecting a sample, if every element in the population has an equal chance of occurring, then the sample is a random sample. Interaction between the arrangement of elements in a population, i.e. its structure, and the sample selection process frequently introduces bias—that is, some elements have more chance than others of appearing in the sample and, hence, the sample is not random. An algorithm for dealing pragmatically with this aspect of the sampling problem offers one way of achieving random samples and, therefore, adequate estimators. Examples of the use of this algorithm on various kinds of geological populations, in both field and laboratory, illustrate the requirements for solving sampling problems and the achievement of appropriate estimators.

Dec 1, 1971

By I S. Lowndes, K. Moloney

Diesel powered equipment is currently used extensively in mining and tunnelling operations around the world due to its mobility, flexibility and through selective application to enhance productivity. However, the increased use of diesel equipment has exacerbated the pollutant load (including heat, humidity, exhaust gases and particulates) placed upon the environmental systems of many underground operations. This expansion in the use of diesel equipment has prom pted researchers to evaluate m easure ment and control technology. This paper reviews the recent research conducted in various countries.

Jan 10, 1996

By G W. Clamp

The most traum atic event within the lUK coal industry during the last 30 years was its privatisation. Who were the relatively unknown people from RJB: white knights or robber barons? This paper highlights the strong safety and progressive engineering cultures th at existed and continues within the company. A long-term view of the business coupled with proven professionalism is amply developed. Quite dearly, to revert to private ownership is not a return to Victorian values but ‘back to the future’.

Jan 8, 1997

By Schwartz M.

Respect for mining in Botswana is long-standing. This article looks at Africa's most transparent mining regime and some of its ambitious plans. Botswana's mining industry value is forecast to average 5.2% growth from 2014-2018 with solid growth for the diamond sector and acceleration of coal production. Respect for the country's mining regime is maintained in the Fraser Institute 2014 annual survey where Botswana occupies the 26th position of 122 administrations. Botswana's transparency is illustrated by Mupane gold mine near Francistown, Ghaghoo diamond mine in the Gope area and the Morupule coal mine

Mar 1, 2015

By Simons W.

The object of the paper is to describe the standards of quality that should be specified in ordering material ordinarily required for colliery use, and also the qualities most suitable for particular purposes. Tables are presented of British Standard tests for wrought iron grades A, B and C, Admiralty tests for iron in chain, the quality of material for wheels and axles, and the composition and mechanical properties of wrought iron, Armco (ingot) iron and drawbar-gear steel. (Paper presented at the North Staffordshire Institute of Mining and Mechanical Engineers' general meeting held in Stoke-on-Trent, March 27th 1916, Mr. John Gregory, President, in the chair)

Dec 1, 1916

By T Atkinson, A Cobb, R AJIington

Risk management is concerned with the whole spectrum of financial, geological, engineering, legal, governmental, social and occasionally ethnic issues, concerned with mining projects. The inherent risks in mining operations are well publicised, but new issues and hazards arrive on the scene and lake precedence, but the older risks still remain, while insurance cover may not he ‘full cover’ in the future. It has long been recognised that quantitative approaches to risk analysis can play a major role, but although these methods are capable of considerable theoretical precision, the lack of sound risk input data and experienced personnel limits the usefulness of theoretical analysis. It can, however, greatly assist in comparing cases, in identifying areas of risk and help in the investment decision process. Its major contribution to a mining project is that it imposes an investigative discipline that also assists in improving the quantitative approach to risk analysis and hence risk management. Risk analysis and risk management also requires sound common sense and major inputs from experienced geologists, mining, mechanical, electrical and mineral processing engineers. The Engineering Council, in 1992, issued a ten point code of professional practice entitled ‘Engineers and Risk Issues’ (The Engineering Council. 1992), covering our professional responsibilities, the law, our conduct, the need for a systematic approach to risk issues, the use of professional judgement, communications, risk management, evaluation of risk, our professional development in this field and the encouragement of public awareness of risk issues. This is a specific area of training perhaps long neglected by our industry and academic institutions (Atkinson. 1983).

Jan 5, 1996

By S K. Das

An intensive investigation into modern roof support technology, including hy draulic and control systems, has been carried out against the perspective of global development and support behaviour on longwall faces across the Indian sub-continent. The wide ranging study examined various types and designs of modern supports used in seams of varying thickness and inclination where caving and stowing were practised. Consideration has been given to structural analysis, support resistance, the various forces acting over and on the powered supports and to support compatibility. The examination of the phy sical parameters has been allied to field experience and, together, have led to the formulation of standard designs for both the powered support structure and structural systems. A realistic mathematical model has been formulated for calculating the capacity of roof support requirements resulting from the actual behaviour of the immediate roof stratum. As a result of the work, it should be possible to readily select the most appropriate type of support sy stem for the conditions and longwall mining method that is to be employed.

Jan 4, 1997

By R. Winand, P. Harlet

he cathodes produced are of electrorefined grade; metallographic structure and surface roughness are controlled to a depth of 1.3 cm (single-side deposits); silver levels in the cathode are regulated by the presence in solution of Cl- and Br- ions; organics must be used at very low concentrations (around 0.1 mg/l with a consumption of about 0.01 mg/l/hr). The required concentrations of additives were established according to a well-defined strategy based on the consumption of organics at the cathode by a mass transfer limited-process.

Jan 4, 1992

By Walshe J. M.

The slow-speed compressor is giving place to the high-speed type, with its greater economy of material and space; and, where very large units are required, the turbo-compressor is supplying the need. In the very large air-supply stations on the Rand, turbocompressor units of a capacity of 20,000 and even 50,000 cubic feet, requiring 4,000 to 13,000 horsepower, are quite a commercial proposition, and have proved a practical success. Air-compressors of this size are, however, very exceptional, and the high-speed reciprocating compressor is quite capable of dealing with the highest outputs so far required in this country and, in the hands of manufacturers experienced in the design of high-speed steam-engines, a very high standard of reliability and efficiency in operation is obtained. The so-called “high-speed” or more correctly quick-revolution type of compressor is now extensively used in mines and collieries; for the air-pressures required for power purposes in mining work, two-stage compression, with an intercooler between stages, is the design usually adopted in best practice. It is not the writer’s intention to describe a variety of high-speed air-compressors but to select as an example of this type of compressor the one with which he is most familiar, and which is probably more largely used than any other, namely, the double-acting two-cylinder two-crank type with automatic light-plate air-valves, and with the working parts lubricated on the forced-lubrication principle. Sectional drawings, efficiency curves, air-cylinder diagrams and other data accompany the descriptions and photographs of compressor design, components and mine applications

Dec 1, 1916

By D. J. Burdon, Anthony Caplan

"(1) The radiological appearances of pneumokoniosis on the Kolar Gold Field is described in detail. The characteristic abnormality is the. presence of a diffuse, fine annular and punctate mottling. (2) The frequency of symptoms could not be determined with any degree of accuracy, but it is believed that symptoms are absent and there is no incapacity until profuse radiological mottling is present, i.e., after long exposure to dust. (3) There is an increased predisposition to tuberculosis, which, if it occurs, affects the prognosismost unfavourably.(4) Pathological examination shows that the radiological mottling is due to the presence inthe lung of numerous small dust-cdll aggregates (up to T5 mm. in dia.) deposited around the smaller bronchioles and blood-vessels.(5) The dust-cell aggregates are relatively acellular but when tuberculosis is superadded thereis an excessive cellular and fibrotic reaction.(6) The difficulties of defining the radiological and pathological appearances of early pneumokoniosisare discussed.(7) The incidence of pneumokoniosis in 7,653 workmen with 5 or more years’ undergroundservice was 43-75%, but it is suggested that in future the incidence will be appreciably lower.(8) The methods of- dust production and the chemistry of mine dust are described. It isshown that the free silica-content of air-borne mine -dust is relatively low.(9) The aetiology'of the pneumokoniotic lesion is discussed."

Jan 1, 1947

By M. G. Fleming

The professional mineral engineer is an individual of personal integrity who has undergone rigorous intellectual instruction in the scientific disciplines fundamental to his vocation; he has learnt to apply these disciplines to the discovery, mining and treatment of mineral resources and, through practical training and experience, has acquired competence and judgment to fulfil his undertakings. In the course of this development he has recognised and accepted a threefold responsibility to society, to his employer and to his profession

Dec 1, 1971

By J R. Leeming

The paper describes a technique that has been developed by the Health and Safety Executive (USE) to make an assessment of the effectiveness of Health and Safety (H and S) management at complex sites. The paper then describes how the technique was adapted and used for the first time at a large coal mine. The results highlighted certain deficiencies in the safety management system, allowing directed advice to he given to management.

Jan 4, 1997

By R. J. Howarth, P. L. Llowenstein

The errors resulting from field sampling, sample preparation and analysis are investigated for drainage sediments derived from homogeneous sandstone, shale, limestone, basic igneous and granite lithologies as a background to a primary reconnaissance survey of England and Wales. Emission spectrographic analyses of approximately 350 samples for Al, Ca, Fe, K, Si, Ba, Co, Cr, Cu, Ga, Li, Mn, Ni, Pb, Sc, Sn, Sr and V and atomic absorption analyses for Cu, Ni, Mn, Co, Zn and Pb have been treated statistically. For routine broad-scale surveys analysis of the unground -80-mesh sediment fraction proves satisfactory. Sampling error between localities in a stream is shown to be less than spectrographic analytical error for many of the elements considered here, except where mineralisation (contamination) occurs, but exceeds the atomic absorption analytical errors in most cases. Unless it it critical to reduce the amount of between-site variability (having regard to analytical errors) in the regional survey, there appears to be no advantage in the use of a more sophisticated sampling technique. The utility of moving-average maps in reducing the width of the confidence belt around the regional 'geochemical surface', and thus compensating to some extent for the sampling errors, is also demonstrated.

Dec 1, 1971