Search Documents

By Nick Hytiris, Mohammed Al Maadheedi, Slobodan B. Mickovski

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.

By Pancho J. Garza, Keith H. Dahlen, Chris A. Labye

"Design for reconstruction of the East Flagstaff traffic interchange project located in Flagstaff, Arizona posed particular challenges. The proposed design included construction of a nearly 50-foot tall mechanically stabilized earth (MSE) wall given rightof- way constraints and soft subgrade soils. The tight right-of-way, approximately 15 feet in certain locations, adjacent to existing structures limited the number of viable remedial alternatives to provide grade separation at the proposed bridge abutment without significant settlement. Preliminary analyses indicated the existing subgrade soils - consisting primarily of relatively soft silts and clays with decomposed pumice - would settle approximately 12 to 14 inches resulting in unacceptable wall deformation. Stone columns placed via vibratory methods (vibro-replacement) consisting of circular excavations which penetrate to firm bearing soils and which are filled with crushed stone were selected to densify the existing subgrade soils. The implemented mitigation measures helped limit settlement to less than one inch and allow for successful construction of the project. The project history - including site constraints, subsurface conditions, evaluation of remedial alternatives, stone columns methodology, and effectiveness of ground improvements - will be discussed.IntroductionThis paper describes the subsurface investigation performed for the reconstruction of the Business Route 40 (B-40) (Country Club Drive) and United States (US) 89 Traffic Interchange (TI) located within the city limits of Flagstaff, Arizona. This project is currently referred to as the East Flagstaff TI. The Project Site Vicinity Map is shown below.The former B-40/US 89 TI was considered ineffective in handling the current and projected volumes of traffic which transition from northbound (NB) B-40 to US 89 (both directions), as well as from southbound (SB) US 89 to SB B-40. The intent of the project was to reconstruct the TI to better accommodate projected traffic volumes. The project eliminated the existing ramps from both NB B-40 to SB and NB US 89. The new interchange includes a Tee intersection from B-40 to US 89. In order to accommodate this alignment, the profile of US 89 was raised several feet (on nearly the same as existing horizontal alignment) to match the elevated profile of B-40. B-40 was shifted just west of its current alignment to accommodate construction of a new, wider bridge structure which spans over Industrial Drive, the Burlington Northern Santa Fe (BNSF) railway, and old Route 66. South of the new bridge, B-40 transitioned back to the existing alignment just north of the I-40/B-40 TI. Within the project limits, both US 89 and B-40 were widened to three travel lanes in each direction."

Jan 1, 2015

By Wolfgang G. Brunner

In the far north of Uttar Pradesh Province in the Indian Himalayas, the 280 MW Dhauliganga hydroelectric power plant is under construction by National Hydroelectric Power Corporation (NHPC), a state- owned enterprise, and a joint venture of Kajima Corporation of Tokyo and Daewoo Corporation of Seoul. This project sets out to develop the lower section of the mountain cascade of the Dhauliganga River, a tributary of the Sarda River, with a 311 m gross head. The 1360 km2 mountainous catchment area is bounded in the north- east by the Chinese border and in the south- east by the Nepalese border. The dam project is located in a remote area north of the principal town of Darchula of the upper Sarda valley, which is one of the seismically most active regions of India. The 56 m high rock fill dam, which will be the first of its kind in India, is faced with concrete and has a 1 m thick, at its crown 270 m long and over 70 m deep cut- off wall of plastic concrete below its toe. The cut- off wall, with a total area of 7500 m2, is constructed by a combination of Bauer hydraulic grabs, assisted by chisels and a Bauer BC 40 cutter which enables the overlapping joint system to be installed, guarantees optimum verticality and enables the cut- off to be keyed into the bedrock formation.

Jan 1, 2004

By Stefano Pirrello

"Sydney’s booming real estate market has pushed property developers to invest in historically “no-go” areas, which were previously too expensive to develop. These areas are usually near rivers where the sites are underlain by deep alluvial and estuarine sediments. In these ground conditions conventional bored pile techniques are often not competitive. Contiguous Flight Auger (CFA) and Drilled Displacement Piles (DD) techniques are on the other hand suitable for these ground conditions. This paper deals with the design and construction challenges encountered with these piling techniques for a series of high-rise towers in Sydney’s West. The advantages of DD over CFA piles such as reduced overall spoil with substantial cost savings and achievable rock sockets in medium strength bedrock are discussed. Design validation through interpretation of real-time data from the piling rigs’ on-board computer data, and low and high strain pile dynamic testing (PDA) is discussed. Testing data is presented as CAPWAP (Case Pile Wave Analysis Program) analyses for different concrete grades.INTRODUCTIONThe booming real estate market in Sydney has pushed property developers in investing in historically “no-go” areas, which were previously too expensive to develop. These areas are usually near rivers where the sites are underlain by deep alluvial and estuarine sediments. In these ground conditions conventional bored pile techniques are often not competitive. Contiguous Flight Auger (CFA) and Drilled Displacement (DD) Pile techniques are on the other hand suitable for these ground conditions and were utilised using concrete injection methods. This paper deals with the design and construction challenges encountered with these piling techniques for a series of high-rise towers in Sydney’s West.GEOLOGY & GEOTECHNICAL CHARACTERIZATION OF THE SITEThe Sydney 1:100 000 Geological Series Sheet shows that the site is underlain by man-placed filling and alluvial/estuarine sediment. The sediment comprises silty to peaty sand, silt and clay. Shell layers are also expected to be present within the soil profile. The Prospect/Parramatta River 1:2500 Acid Sulphate Soil Risk Map shows the site as ‘Disturbed Terrain’ in which soil investigations are required to assess acid sulphate soil potential. Several Cone Penetration Tests and Boreholes were carried out during the geotechnical investigation. All boreholes were extended to bedrock and NMLC-sized diamond core drilling was used to obtain 50mm continuous core of the rock, enabling unconfined compression strength testing to be carried out on selected samples. A summary of the ground conditions encountered on this site and inferred from the CPTs can be described as follows:"

Jan 1, 1900

By Kenneth Gavin, Weichao Li, Paul Doherty

"The lateral load capacity is one of the most important issues to be considered in designing piles to resist berthing loads, ship impact forces and for monopiles used in the offshore wind sector. A number of semi-empirical design approaches are available to calculate the ultimate soil resistance and assumed soil reaction profile along the piles’ embedded depth. In order to investigate the response of monopiles to lateral loading, a series of field experiments were conducted on instrumented steel pipe piles. Two lateral loading tests were performed on model piles with a diameter, D, of 340 mm and embedded depth, Lem, of 2.2 m, giving a Lem/D ratio similar to those adopted in the offshore wind sector. The piles were driven into dense sand at the University College Dublin geotechnical test bed site in Ireland. 10 pairs of strain gauges were installed on each model pile along the embedded depth at 10 levels to capture the load transfer and bending moment within the piles. The deflection and rotation at the model pile head were measured by Linear Variable Differential Transformer (LVDT) and inclinometers. The tests results were used to perform a detailed evaluation of current design methods. In the final section, discussion on the determination of the ultimate lateral load capacity for monopile design was conducted. IntroductionA pile’s lateral load capacity is determined, for design purposes, by two conditions: 1) the ultimate lateral load, Fu, divided by an appropriate safety factor; and 2) the load according to the maximum lateral deflection that the support structures can sustain. In view of the first condition, design methods to calculate the ultimate load were developed for piles used in the offshore oil and gas sectors, which tend to be much more slender than monopiles used in the wind industry. The purpose of this study was to investigate whether these design methods provide reasonable estimates of ultimate capacity, for short rigid monopiles.The methods to determine the ultimate lateral load generally follow three steps: 1) determine the ultimate soil resistance, Pu, along the pile embedded depth; 2) adopt the most appropriate soil reaction profile, Pz, along the piles embedded depth when the pile subjected to the ultimate lateral load condition (four of the most popular ones are depicted in Figure. 1); and 3) ensure equilibrium of lateral forces (see Equation 1, symbols are listed at the end of the paper) acting on the pile and bending moments (see Equation 2) about a point in pile is employed to determine the ultimate lateral load."

Jan 1, 2015

By Y. M. Ha, T. D. Nguyen, D. T. Nguyen, H. K. Choi

Conventionally, cement deep mixing (CDM) columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern may be inefficient in cases of spread footings or shallow foundations. This paper first briefly introduces principles of an improved CDM method that can create head-enlarged CDM (termed PF) columns. A simple analysis approach was introduced to obtain optimal shape of PF columns that results in minimum settlement. The effectiveness of this improved method over the conventional CDM method was then illustrated by settlement analysis for an actual footing in a case study using two recommended analytical methods in the literature. Analysis results from the case indicated that by using the same amount of soil-cement mixed volumes, settlement from a footing on PF columns can reduce up to 10 % compared with that from the same footing on CDM columns. In addition, a material quantity comparison for the case indicated that to have the same settlement values the volume of each PF column can be reduced of around 10% compared with that of the CDM column. INTRODUCTION The cement deep mixing (CDM) method is one of the most popular methods in ground improvement works. Details on the method such as construction procedures, necessary equipment and recommendations are described in many references or manuals (e.g. Bruce et al. 2013, BS EN 2015, Kitazume and Terashi 2013). Conventionally, CDM columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern is found inefficient in cases of spread footings or shallow foundations as the upper soil layers are naturally weaker than the deeper ones but are subjected to larger amount of induced stress from the superstructures.

Jan 1, 2019

By João Veludo, Eduardo Júlio, Helen D. Robinson, Jesús E. Gómez

"Utilization of micropiles for structural retrofit requires connection of the micropiles to the footings of the existing structure. Almost ten years ago, an experimental research effort was carried out in the US to investigate the magnitude and mechanism of development of the bond strength between micropiles and existing concrete. The study resulted in important conclusions on the mechanism of connection capacity development and provided specific recommendations for practical design of micropile-to-footing connections. In the last five years, the original study was complemented by an intensive experimental effort in Portugal aimed at answering many of the questions still remaining on this topic. This paper is a summary of the knowledge that is presently available on the capacity of micropile-to-existing footing connections. It presents the results and observations of model tests performed in the US and Portugal, as well as some tests from actual construction sites. The paper presents clear evidence that friction may be the most important component of connection capacity. It also presents a clear correlation between confinement and connection capacity.IntroductionUtilization of micropiles for structural retrofit requires connection of the micropiles to the footings of the existing structure. This is often accomplished by drilling through the footing and developing the connection by direct bond between the micropile grout and the existing concrete. Almost ten years ago, an experimental research effort was carried out in the US to investigate the magnitude and mechanism of development of the bond strength between micropiles and existing concrete. Smooth and textured micropile inserts of varying lengths were tested to failure inside pre-drilled holes of varying diameters. That investigation led to several publications (Gomez et al. 2005, Wilder et al. 2005, Cadden 2009) on the mechanism of development of bond strength between micropiles and concrete, which included a chart for preliminary bond value selection depending on the diameter of the hole and texture of the micropile.An intensive testing program was carried out in Portugal in the last five years. The program focused on answering questions posed by the original investigation and on finding the relationship between connection capacity and level of confinement. Both investigations, and especially the testing performed in Portugal, provided an invaluable amount of information on the mechanisms of failure of micropile-to-footing connections. This information should be the basis for development of design procedures that, until now, were not available."

Jan 1, 2015

By Lorie M. Dilley

Alaska Village Electric Cooperative (AVEC), an electric utility cooperative providing power to 51 Alaska villages, has made a concerted effort to install wind turbines in the villages they serve in an effort to mitigate the growing costs of electrical power generation. The subsurface soils in several of these villages consist of sands and silts with ground temperatures of between 30°F and 32°F. The presence of warm, degrading permafrost in three of the villages has required innovative foundation designs, including the use of helical piers and piles to support steel and concrete wind turbine foundations. The design of the deep foundations had to account for the effects of degrading permafrost likely resulting from observed climate change patterns. Uplift forces imposed on the foundations were approximately 100 kips per pile. Uplift pile load testing was conducted on the installed piers and piles in order to determine the actual working load that each pier or pile could sustain. In addition, pile driving analyzer testing was conducted on several piles installed in the permafrost and compared to pile load tests. Results indicated that the installed piers and piles achieved the necessary capacity with sufficient factors of safety. Thermosyphons were installed near the foundations in order to limit the effects of climate change on the permafrost. The two to four wind turbines in each of the three villages are currently operational. Refinement of the design based on the pile testing from the first village to the third has decreased the cost of the tower foundations and improved our understanding of designing for warm, degrading permafrost.

Jan 1, 2010

By Andreas Andenæs, Arne Schram Simonsen

"AbstractThe Tresfjord bridge is with its variety in foundation concepts and difficult soil conditions one of the most geotechnically challenging projects in Norway at the time. The project comprises design of large concrete caissons, steel core piles through large rock fills, and closed end steel pipe piles in up to 40m water depth driven in very hard moraine. Test piling has also been conducted to check feasibility of the concept, and PDA measurements have been used to verify sufficient capacity of piles. FactsThe Tresfjord bridge is part of the new export road from Ålesund to Åndalsnes on the North-West coast of Norway built by the Norwegian Road Administration. The bridge will reduce travel time with about 30 min between the cities, see Figure 1. The bridge is planned to open summer 2015.The Bridge crosses the Tresfjord and will be 1290 m long. The bridge is built as a free cantilever bridge and will be resting on a total of 20 nos. of foundations, where two are abutments resting on steel core piles, three are casted directly on bed rock and 13 are foundations resting on steel pipe piles. The last two foundations holding the main span will be concrete caissons resting on bed rock and moraine. Figure 2 shows a 3D model of how the finished bridge will look. Multiconsult AS is responsible for design and pile supervision , while the Joint-Venture Bilfinger-Tresfjordbridge ANS is responsible contractor.Soil ConditionsPercussion soundings and sampling together with coring have been performed in the individual foundations using a small geotechnical equipped vessel. Acoustic and refraction seismic profiling have also been carried out to tie in the layers between the boreholes.The soil conditions are varying over the length, but are in general dominated by a soft top layer (2-4 m) of sediments over very hard moraine with occasionally large boulders. Piles in the two foundations closest to shore on the western side of the bridge are piled to bed rock with penetrations up to about 27 m in soil.Water depth varies from about 10 to 40 m for the piled foundations. Figure 3 show how the topography of the seabed varies over the bridges length."

Jan 1, 2014

By James M. Tantalla, Jr. Ellman

"Construction of the powerhouse for the Willow Island Hydroelectric Project, located at the Willow Island Lock and Dam, required a 120-ft deep temporary excavation inside the limits of a cellular cofferdam on the Ohio River side of the excavation and a soil-bentonite seepage cut-off wall on the landward side of the excavation. Stability analyses were performed for critical sections to evaluate the stability of the soil slopes and rock cuts using limit equilibrium, tension crack, and buckling analysis techniques. The stability analyses indicated adequate factors of safety through the landside embankment sections, and for the weighting berm soil slopes in front of the riverside cellular cofferdam. However, the results of deep-seated stability analyses through the rock supporting the riverside cellular cofferdam indicated marginal factors of safety for the 100-year flood condition. Consequently, the riverside portion of the excavation required enhanced stability measures, namely the installation of long, high-capacity rock anchors. Also, the dewatering system was modified to lower the site piezometric head to near the top of rock to improve the stability of the rock cuts.Thirty high-capacity rock anchors were installed on the upstream, riverside, and downstream sides of the cofferdam rock cut. The rock anchors consisted of multiple, seven-wire strands designed to provide the full-required design load at 60% of the strand capacity. Rock anchor loads varied from 1,968 to 2,074 kips. The maximum number of strands per anchor was 59. Bond lengths assumed an allowable bond stress of 100 psi based on the rock bond from pull-out tests.Project DescriptionAmerican Municipal Power, a nonprofit organization that owns and operates electric generation facilities for its member communities, has been in the process of constructing hydroelectric power plants adjacent to existing navigation locks and dams along the Ohio River. The Willow Island Hydroelectric Plant was recently completed on the West Virginia bank of the river adjacent to the US Army Corp of Engineers (USACE) Willow Island Lock and Dam. The plant is on the opposite river bank to the locks, and includes two turbine generating units with FERC rated capacity of 44MW at a 20-foot head differential. The Ruhlin Company of Sharon Center, Ohio was awarded contracts to construct both the cofferdam and the powerhouse. Construction began in mid-2011, and was completed in early 2016."

Jan 1, 2016

By Adam Zagorski, Rusty Lucido, Curt Scheyhing

"The current California Department of Transportation (Caltrans) practice based on AASHTO LRFD Bridge Design Specifications is to use the O’Neill and Reese method (FHWA, 1999) for calculating the side resistance and base resistance of Cast-in-Drilled-Hole (CIDH) piles / drilled shafts. In this calculation, end bearing is typically neglected for piles constructed using a wet method due to questionable reliability of end bearing resulting from soil disturbance and inadequate cleaning of the base. Pressure grouting below the tips of drilled shafts in cohesionless soils has long been used worldwide to provide reliable end bearing capacity, but for decades it was relatively unused in this country. It has been used increasingly in the United States over the last decade. Before this project tip grouting has not been utilized on or accepted by Caltrans to maximize piles end bearing capacity. This project proved that tip grouting to mobilize reliable base resistance can be successfully implemented on a full-scale bridge project requiring over 350 large diameter shafts.For the Gerald Desmond Bridge Replacement Project, Shimmick/FCC/Impregilo, JV utilized a temporary Oscillator casing to the full depth to install CIDH piles. Piles were constructed by the wet method and then pressure grouted below the pile tip. A tip grouting procedure for these large diameter shafts was developed and tested to specifically address the geology and constraints of the project. This procedure was then proven during the Load Testing of test piles during the Test Shaft construction phase of the project. Tests showed a minimum reliable base resistance of 150 ksf could be mobilized in very dense sand at a downward movement of 5% of the pile diameter for piles ranging from 4.9 to 8.2 feet in diameter. By tip grouting, the length and diameter of the piles were significantly reduced."

Jan 1, 2017

The development of Augered Cast-In-Place (ACIP) piles started in the late 1940's when several projects were performed by Intrusion-Prepakt, Inc. utilizing various techniques to place the piling. On some projects, a grout pipe was placed down the augered hole after the auger was withdrawn, and structural grout was pumped into the hole until grout appeared at the surface, after which the grout pipe was withdrawn. In some instances coarse aggregate was placed after a grout pipe was in place, and then the grout was intruded into the coarse aggregate, making a pile using the preplaced concrete method. Another method of forming augered piles used a system of driving or drilling a grout pipe through soils adjacent to the auger once the auger was drilled to the bottom elevation. The tip of the grout pipe was placed in close proximity to the tip of the auger. As the auger was withdrawn, grout was pumped through the grout pipe filling the augered hole from the bottom. After grout was observed at the surface, the grout pipe was withdrawn. In 1951, a patent was applied for by Raymond Patterson describing the above techniques along with a technique for placement of grout using a hollow stem auger and a removable plug or lead bit at the tip of the auger. The expendable plug or lead bit was removed by using grout pressure. The patent was granted in 1956. Around this same time other augered piling con-tractors began operations under licensed arrangements.

Jan 1, 2003

By Jon Huff, Jeffrey Donville, Hannah Iezzoni, Dan Stevenson

Occasionally, in the design of deep foundations for a structure, a single deep foundation element may be used to support a building column. The most common type of element used in such cases is a drilled shaft (also referred to as a drilled pier, caisson, or bored pile). However, as installation capabilities have improved, large diameter augercast piles are increasingly more common. While drilled shafts and augercast piles differ significantly in construction methods, in the eyes of the International Building Code (IBC), both are treated as cast-in-place deep foundations and must comply with many of the same code provisions. Deep foundations are required to be braced such that lateral stability is provided in all directions, however isolated, cast-in-place elements that have a diameter (D) of at least 2-feet and a length (L) not more than 12 times the diameter can be an exception. In response to the concerns raised by some member professionals, the Deep Foundations Institute’s (DFI) Augered Cast-in-Place Pile and Drilled Displacement Pile Committee took a closer look at the code and its applications, the historical development of the code language through the years and performed analytical modeling to evaluate the impact of this ratio on a pile’s stability. The question is whether the limiting ratio included in the IBC 2018 code provisions is justified, or whether different criteria should be used to determine when isolated deep foundation members are allowed.

Sep 8, 2021

By Alessandro Bertero, Stefano Valagussa, Filippo Maria, Wesley Schmutzler, Leoni

"Abstract The Deep Mixing Method (DMM) represents a viable solution to improve the adverse geotechnical properties of foundation soils. Differences and the importance of performing pre-construction laboratory and field tests will be highlighted. Comparative analyses and interpretations between the various lab and field stages, along with accumulated information about soil properties and QC results, allowed fine-tuning of the production parameters throughout almost the entire project.Two projects where the US Army Corps of Engineers selected the Deep Mixing Method (DMM) for the required stabilizations, and a third project completed in Italy, will be illustrated:•,?the LPV 111 Project (New Orleans - LA – USA); DMM was used for groundimprovement/foundation strengthening and consequently stabilize and support the burden of the new levee.•,the Rio Puerto Nuevo Project (San Juan - PR - USA); DMM was applied to improve the soils adjacent to a 90” forced sewer main relocation and to improve the soils for the base of a new drainage channel•,the new Italian high speed railway project (Florence Italy); DMM technology was applied to realize a a TBM break in/break out, foreseen originally by jet-grouting.IntroductionThe Deep Mixing Method (DMM) represents a viable solution to improve the adverse geotechnical properties of foundation soils. The effectiveness of working parameters depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product."

Jan 1, 2014

By Chu E. Ho

This paper reviews the design of jet grouting at re-entrant corners of excavations where the diaphragm wall and secant pile wall installation were interrupted by existing utilities in the streel sidewalk. Jet grout blocks were formed to seal the gaps in the walls for excavation support, consisting of four to six columns in clusters. Jet grouting was performed around an electrical duct bank which had to be maintained. Jet grouting was executed through stratified soils using various combinations of jetting parameters for different soil strata. The installation sequence and age of the neighboring columns within a cluster will affect the jet’s ability to form subsequent columns. When jet cutting is limited next to hardened grout columns or embedded obstructions (such as diaphragm walls or secant pile walls in this case), the specific gravity (SG) of spoils would be reduced and tend toward the value of the injected grout SG. The magnitude of spoil SG is also influenced by the variability of the grout mix supplied. Specific Gravity Ratio (SGR) defined as the ratio of spoil SG to the actual grout SG at the time of jetting can be used as an indicator of successful treatment, with SGR > 1.0 indicating effective soil erosion. Verification coring and testing were implemented to confirm target column diameter and strength of grouted soils have been achieved.

May 1, 2022

By Manuel M. Reyes, Thuraisamy Thavaraj, Alex Sy

"The new east span of the San Francisco-Oakland Bridge features a single tower self-anchored suspension (SAS) bridge. During construction of the SAS bridge, a temporary bridge was used to support the box girders until erection of suspension cables was completed. The transfer of deck load from the temporary bridge to the suspension cables was achieved in November 2012 and the SAS bridge has become the largest of its kind in the world. The new bridge will be in service in Fall 2013.Large diameter driven steel pipe piles were used for the temporary bridge foundations at Towers D, F and G located in San Francisco Bay. At Tower D, the large diameter steel pipe piles were driven through thin overburden into bedrock using a large Menck MHU500T hammer with a rated energy of 550 kJ. As there was no precedence in driving open-ended pipe piles into the Franciscan Formation bedrock, challenges were faced with uncertainties in drivability, driving stresses, pile embedment in bedrock and pile capacity. These uncertainties were addressed by incorporating additional measures into the pile design, and by the use of dynamic pile monitoring during initial driving and re-strike. Pile relaxation was observed during pile installation.At Towers F and G, setup effect was a key issue for the piles driven into the deep soft marine sediments. Drivability analyses were conducted to predict pile run, driving stresses, selection of hammer and refusal criteria. The piles were dynamically monitored during driving to estimate pile capacities. Due to the set-up effect in the Bay Mud, the piles gained up to 3.3 times the initial capacity during the re-strike and were in excess of the design capacity.This paper presents details of the design, construction, testing and performance of the driven pipe piles at temporary Towers D, F and G. Settlement data of the temporary tower foundations while in service confirmed the satisfactory performance of the pile foundations.INTRODUCTIONThe new east span of the San Francisco-Oakland Bay Bridge features a single tower self-anchored suspension (SAS) bridge, the largest of its kind in the world. The new east span replaces the existing double-deck steel bridge built in the mid-thirties. A span of the existing bridge had collapsed during the 1989 Loma Prieta earthquake but was repaired. Construction of the new east span commenced in 2008 and is expected to be completed for the Labour Day opening in 2013. Figure 1 shows a schematic (looking north) of the new bridge with its 160 m high main tower T1 in the middle, and Piers W2 and E2 at the west and east ends, respectively. The west and east spans of the SAS bridge are 180 m and 385 m, respectively.During construction of the SAS bridge, a temporary bridge, complete with towers and trusses, was used to support the box girders of the new permanent bridge until the loads from the box girders were transferred through suspension cables to the permanent bridge. The transfer of deck load from the temporary bridge to the main cable was completed in November 2012."

Jan 1, 2015

By Shahid Islam, Lucian Bogdan

"The maintenance of infrastructures has been of particular concern to the engineering community. As the world’s infrastructure expands and existing infrastructure ages, monitoring and evaluation of the structures have become more critical than ever. A large number of retaining walls, tie backs, slope stabilizations and piles are designed using pre-stressing steel. Many piles and drilled shafts are designed using reinforcing steel. There are few testing methods available to assess these tension and compressive forces. High cost, complicated equipment and limitation of space often prevent these methods from being implemented. DYWIDAG-Systems International (DSI) has been involved in the development, testing and utilization of DYNA Force® sensors to measure the force in the anchors during construction and at any time during the lifetime of the structure. They can be used for bare, epoxy-coated, galvanized and greased-sheathed steel in the bonded, un-bonded, grouted or un-grouted length of the anchor. The sensor is robust and requires no maintenance. Sensors have received attention in terms of accuracy, performance, ease in installation, durability, and cost effectiveness. This paper describes its application in tie-back and anchor force monitoring of retaining walls and bridge abutment and compression forces in drilled shaft reinforcing steel where the data were collected manually, automated and remotely.INTRODUCTIONOur infrastructure is expanding and the existing infrastructure is aging. Some structures are expensive to maintain and some occasionally fail. There is a large demand for implementing health monitoring of structures. Many tie-backs, retaining walls, dams and other geotechnical structures are post-tensioned and many of them need repair using a post-tensioned system. On many occasions during construction and service life of the structure, it is useful to know the force in the post-tensioning and anchor system. Many piles and drilled shafts are designed using reinforcing steel and the compressive forces in reinforcement are unknown. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive, and the accuracy varies depending on the method used.The elasto-magnetic (EM) technology is a novel approach to monitor forces in steel elements. The DYNA Force sensor is built based on EM technology (See Fig. 1). It is composed of a primary coil and a secondary coil (sensing coil). By passing current through the primary coil, ferromagnetic material is magnetized. The sensing coil picks up induced electromotive force that is proportional to change rate of applied magnetic flux (Faraday's law) and relative permeability. As permeability of core changes, output voltage changes. The output voltage is calibrated to measure the force. A readout unit is designed to magnetically energize the steel through the sensor and measure the response of the steel to the process. The readout unit then converts the response into a direct force reading. The sensor has an embedded thermistor which allows for temperature compensation. Due to the diversity of the magnetic property of steel, calibration is done for each type of steel allowing the sensors to perform at their highest accuracy."

Jan 1, 2017

By Thomas Billups, Brendan FitzPatrick, Doug LeDo, David Carchedi

"Working in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. This paper describes the use of the modular Ductile Iron Pile system, a low-vibration driven micropile, on two urban projects on the Johnson & Wales University campus in Providence, Rhode Island. The paper describes the successful implementation of Ductile Iron Piles installed to develop capacity in end-bearing on one site and friction on the second site. Design, installation and quality control operations are all presented as well as the results of full-scale load testing performed on non-production test piles. This paper is of importance to the industry because it describes a versatile option for project teams as an alternative to traditional micropiles, helical piles or other deep foundation systems for urban sites.INTRODUCTIONWorking in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. Two recent projects in downtown Providence, Rhode Island faced a combination of problematic soil conditions and urban construction challenges including vibration concerns. Both projects were a part of the Johnson and Wales University campus development. Figure 1 illustrates the urban locations of the sites."

Jan 1, 2016

By Bryan C. Field

The proposed construction schedule for the St. Anthony Falls I-35W Bride challenged the abilities of the design-build teams to utilize the best and most efficient methods to meet Minnesota Department of Transportation?s deadlines and design requirements to restore traffic to the Interstate 35W crossing of the Mississippi River, along with a sense of normalcy, following the bridge collapse. The project team ultimately designed and constructed two foundation systems at various substructures for bridge support. Steel H-section piles were driven to bedrock for south bridge abutment support and drilled shafts were used for the north bridge abutment and piers for the Mississippi River Bridge. Drilled shafts we also used for the abutments for the three single span bridges carrying I-35W over 2nd Street. The design-build team used high-strain dynamic pile testing with a Pile Driving Analyzer (PDA) to verify H-Pile capacities and performed drilled shaft inspection on a 24-hour basis during installation over the winter months. The drilled shaft inspection process was a vital part of the project quality control program to maintain the necessary methods for proper drilled shaft installation. Ultimately, with an efficient design, quality construction methods and operation, and a rigorous inspection and quality control plan; the I-35W Bridge was opened to traffic 3 months ahead of the already accelerated schedule.

Jan 1, 2009

By Peter de Kort

Tunnels in urban areas generally require deep excavations in soils under the groundwater table. In The Netherlands uplift loads are generally taken by piles installed into dense sand layers, which are hard to penetrate. To avoid nuisance and damage to the environment, piles often need to be installed using vibration free methods, which also have the advantage of low noise levels during installation. Drilling piles and obtaining a high uplift resistance is a contradiction in itself. Franki has adopted several installation methods based on the injection of grout during drilling and/or post grouting to overcome the difficulty of hard layers. This report presents two projects, situated in Rotterdam and Sneek, where vertical tension piles in floors, subject to high uplift loads, have been used. It also explores a project in Zeebrugge (Belgium), where tension piles are installed at an inclination of 1:1 to anchor a diaphragm wall for a quay construction. Test results presented in this report show, that vibration free and soil displacing piles can be installed in very dense sand layers and that a high uplift resistance can be achieved. It is also shown, that a variety of installation methods is available, even in limited space.

Jan 1, 2008