Search Documents

By J. Brian Anderson

Jointed micropiles were investigated to support bridge foundations where shallow rock was present. In this application, micropiles would have some amount of unsupported length, and would be subject to nominal lateral loads. Five lateral load tests were conducted on micropiles to demonstrate the impact of casing joints and rock socket embedment on lateral behavior. Load tests were simulated with FB-Multipier, a hybrid-finite element program for analysis of deep foundations, for proper design of the loading apparatus and instrumentation. The micropile sections were 2 m (6.56 ft) long, 273 mm (10.75 in) in diameter, 13 mm (0.5 in) thick walled, with a 50-mm (2-in) long threaded joint. Micropiles were made of one to three casing sections and were embedded 0.3, 0.6, 1.5, or 3.0 m (1, 2, 5, or 10 ft) into rock. In each test, two identical micropiles were pulled together using a simple frame until the weaker pile failed. All micropiles were instrumented with inclinometer casings while two contained strain gages at 0.76 m (2.5 ft) intervals. Load and displacement were measured at the pile heads. Tests showed the embedment of 0.6 m, 1.5 m, and 3.0 m (2 ft, 5 ft and 10 ft) sufficiently carried lateral loads over 180 kN (20 tons). The piles embedded 0.3 m (1 ft) were not able to maintain lateral load. In general, all micropiles tested to failure exhibited a brittle failure mode where there is small lateral deflection followed by a sudden failure at the casing joint. This was demonstrated in three of the load tests. In most cases, the micropiles were stiffer and stronger in the load tests than originally predicted numerically. The final test, where piles were not loaded to failure, verified that embedding vibrating wire rebar strain meters in the grout captured the bending moment profile of the micropile. The results showed the maximum moment in this case being carried directly across the threaded joint as predicted by the preliminary models. The results of these tests were used to calibrate the FB-Multipier numerical model. Using a load test that included bending strain measurements for a match, the soil properties were adjusted to produce reasonable matches for all of the load tests.

Jan 1, 2011

By George J. Tamara

The urban environment presents special challenges for the design and construction of earth retention systems. Complications arising from difficult subsurface conditions are compounded by the presence of urban infrastructure and existing and prior construction. The proximity of adjacent structures as well as intense prior use can cause special concerns including the potential for archeological artifacts or contaminated ground or ground water. Utilities and structures may be particularly vulnerable to the effects of ground movement, dewatering and vibrations. Difficulty of access, congestion and limited work areas may severely restrict means and methods of construction. Dewatering may be limited or prohibited because of concerns for disposal of clean or contaminated water, depletion of aquifers, drawing of contaminants to the site or dewatering induced settlements.

Jan 1, 2003

By Mohammed Y. Fattah, Wissam H. S. Al-Sudani

"During installation of pile, a soil column is formed inside the pile. For small depths, the height of the soil column typically equals to the penetration depth (full coring state). As the penetration depth increases, the developed internal shear stresses become larger and reduce the amount of soil to penetrate. At the same time, the soil in pile at the bottom is compacted. This will continue until at a given moment, the soil column is a soil plug, and does not stop moving relative to the pile. This is because the shear stresses developed in the interior of the pile are greater than the load-bearing capacity of the ground.This paper presents the results obtained from 40 model pile tests carried out to assess the effect of soil plug on the model pile capacity. The piles are embedded in sand of different densities with different lengths of piles and types of pile-ends. The model tests are divided into two parts according to the type of end of the pipe pile used in the model pile test. The first part consists of 32 model open-ended piles with different lengths of soil plug inside the pile. The second part consists of 8 model closed-ended piles.It was concluded that open-ended pipe piles behave as a closed-ended if the soil plug formed inside piles in state partial plug or full plug. Length of soil plug depends on the type of installation and relative density. The pile load carrying capacity in dense sand is several times greater than those in medium sands especially in cases of closed ended piles or open-ended since the pipe pile can produce external and internal skin friction in addition to end bearing resistance that makes the total pile capacity close to that of closed-ended pile. Whether open-ended piles are driven or pressed in the fully coring - fully unplugged mode or in the partially plugged mode, the plug does contribute to static pile base capacity."

Jan 1, 2014

By Jacques Moraille

The public is asking for more aesthetic designs if they can be proven cost-effective at providing an appealing element to new dams. Lake Lenexa was designed and built around the idea of providing for basic dam functions such as flood control, enhanced water quality, recreation but also to provide an inviting community focal point for the residents to visit and enjoy; truly interact with the dam. The architecturally unique dam and ?one of a kind? spillway were designed to symbolize the water cycle as water moves from nature into the urban environment and the back to nature. A pedestrian bridge that spans the spillway offers visitors a good view of cascading pools and a fountain. The original Lake Lenexa dam layout incorporated relatively high, cast-in-place concrete retaining walls to form the spillway structure. The Black & Veatch project team performed a Value Engineering (VE) study to determine cost-effective means for implementing architectural features within the spillway, which resulted in innovative uses of construction materials not typically used in dam and reservoir construction. The VE study concluded that mechanically stabilized earth (MSE) retaining walls that are normally used for transportation projects would be a cost-effective alternative to the originally planned cast-in-place wall systems for the main spillway and stilling basins. The Black & Veatch study added value by mixing cement-kiln dust (CKD) with on-site clay soils to produce a stabilized material for use under the spillway. The CKD stabilized material properties include low compressibility, high strength and low permeability, which reduced seepage and uplift pressures under the spillway slabs. The cost savings provided by the VE alternatives reduced total costs and enabled architectural elements. The award winning dam design also used drilled caissons, expanded polystyrene (EPS) block forms, customized steel forms and external concrete vibrators to build the pedestrian bridge and upper spillway structures.

Jan 1, 2009

By D. A. Bruce

Small diameter cast-in-place bored piles (pinpiles) have been installed throughout the world since 1952, but only more recently in the United States. The special features of their construction and performance makes them ideally suited for structural underpinning applications in difficult ambient and geological conditions. This paper describes the underpinning of part of a major industrial facility near Mobile, Alabama. In addition to being a most interesting and successful case history, per se, the paper also describes in detail a fundamental test pile program which has afforded a unique insight into the basics of load transfer mechanisms.

Jan 1, 1992

By Jørn H. Thomsen

This paper presents the experience gained and the lessons learned over the last decade within the numerous offshore foundation projects undertaken in the offshore waters of Denmark and Belgium by COWI A/S of Denmark. This experience derives from the close collaboration with, and interaction between the owners, contractors, and engineers in the various stages of project development. In turn, the experience draws on COWI's experience within foundation of large bridges world wide over half a century. Focus is on two pioneering gravity base foundation projects: ? Nysted in Denmark, currently the largest offshore windfarm worldwide with 72 Nos Bonus 2.3 MW turbines in water depths up to 10 m in the relatively benign inner Danish waters ? Thornton Bank in Belgium, where the first phase - comprising 6 Nos REpower 5MW-turbines of a total of 60 - are planned to be built in the rough North Sea in water depths exceeding 25 m.

Jan 1, 2013

By Mohammadreza Khanmohammadi, Kazem Fakharian

"AbstractIn driven piles, the gradual dissipation of excess pore water pressure and consequently the soil setup significantly contribute to increasing the pile capacity with time. The question is risen that how the scale differences affect the stress state variations around the pile shaft and at the pile tip? Would the CPT predictions better correlate with End-Of-Drive (EOD) or Beginning of Restrike (BOR) conditions? On the other hand, are the proposed a and ß parameters for clayey soils mostly predicting the EOD or BOR situation? The main objective of this paper is to back calculate the a and ß parameters from CPT profiles, pile Dynamic Load Tests (DLT) at the EOD and BOR as well as Static Load Tests (SLT) and evaluate how they compare with those suggested in literature. Four precast 400 mm square concrete piles driven in North Azadegan Oilfield in Khuzestan Province were selected for the comparisons. CPT test results were available from the extensive geotechnical investigation at the study site. DLT tests using PDA were carried out at EOD, 1 day and 14-day BOR on all the 4 piles. All the piles were SLT tested as well. The UniCone software was used to estimate the tip and shaft resistances using 4 methods including the Dutch, Eslami & Fellenius, LCPC and Schmertmann. The results indicate that the a-method based on the proposed values in literature has predicted a shaft capacity of 90% of the 14-day BOR. This is while the ß-method has predicted a shaft capacity equivalent to 1-day BOR results only. Therefore, both methods have under-predicted the shaft capacities compared to real capacities measured after the significant soil setup in the study area. Two of the CPT methods have underestimated, one has overestimated and one has matched the estimated 60-day capacity."

Jan 1, 2014

By Jeffrey R. Hill

To extend the life of the Merchants Railroad Bridge crossing the Mississippi River in St. Louis, MO, the owner implemented a rehabilitation and reconstruction project. The Merchants Bridge provides a key link in the transcontinental railroad system. The bridge is of local importance to the Terminal Railroad Association ? providing a link between St Louis and a rail switching yard in Venice, IL. The intent of the bridge rehabilitation is to keep the Merchants Bridge in service, even though the bridge was originally constructed in the 1890?s. The project involved replacing the East and West approach deck truss spans with new deck girder spans. The rehabilitation program required construction of new concrete piers to support the new spans. In order to reduce the track down time to two, ten day single track shutdowns, the specifications required that all foundation and substructure work be completed while leaving the existing spans in place. The preliminary bridge design specified rock-socketed drilled shaft foundations. Drilled shafts proved to be challenging due to working from beneath the existing bridge, a high water table, utilities, a flood wall, and existing rail way lines. The micropile alternative was technically appropriate given the access limitations, shortened the foundation rehabilitation schedule by several weeks, and realized a significant cost savings to the Owner.

Jan 1, 2006

By Geoffrey D. Collins

This paper deals with the construction of the Effluent Outfall Diffusers which form part of the outfall for the Deer Island sewage project. The work was executed 15 km out to sea in Massachusetts Bay and required the drilling, installation, grouting and accurate determination of the actual position of 55 riser shafts in 33.5 m deep water. Although not strictly a "foundation", the contractor's approach to the installation of the diffusers was a logical development from many marine foundation projects executed by the Contracting companies over the last decades. The only previous application of this design of outfall had been in Australia where offshore oil drilling techniques had been adapted for use in riser installation.

Jan 1, 1994

By Barry C. Slocombe

The development of new ports, extensions of existing facilities and reclamation of former docks will involve consideration of a variety of geotechnical problems. This paper presents data including instrumentation of structures from three UK projects involving vibro techniques to provide economic engineering solution.

Jan 1, 2008

By David S. Yang

The Cement Deep Soil Mixing (CDSM) method introduces and mixes cementitious materials with in situ soils using hollow-stem rotating shafts equipped with a cutting tool at the tip and mixing paddles above the tip. CDSM generally produces a soil-cement panel consisting of three overlapping soil-cement columns. The soil-cement panel is then extended to form walls, which are effective for excavation support and groundwater control due to the continuity and low permeability of soil-cement walls. Two design approaches could be taken in the application of CDSM for excavation support: 1) single wall design and 2) gravity wall design. The former one is treated as a wall technology and the latter one is treated as a soil stabilization method. This paper will review the CDSM equipment and installation procedures for the construction of these two types of soil-cement walls. Four case examples are used to illustrate the design and application of these two types of soil-cement walls.

Jan 1, 2003

By D. T. Bergado

The uppermost subsoil profiles of the Bangkok plain can be divided into four layers, namely: weathered clay, soft clay, stiff clay, and dense sand layers. The soft Bangkok clay is a normally consolidated marine clay with built-up preconsolidation effects and overlain by a weathered crust. Up to the present, a large number of full-scale tests on excavations and pile foundations has been made by numerous investigators. Based on these results, the available data are reviewed and evaluated. The results show that for test excavations, the excess pore pressures were overpredicted by the existing theories. The vertical and lateral movements in the excavations can be predicted by the bilinear and non-linear finite elements using appropriate modulus values. Relationships among probability of failure, safety factor, and safety margin of the excavation were also obtained. In the case of pile foundations, good agreement between the measured and predicted ultimate pile capacities were obtained for long piles. The adhesion factors ranged from 0.4 to 1.0 while the average skin friction factor was found to be 0.33. The ultimate capacity of the pile was also predicted successfully by using the Dutch cone data. For lateral deflection of piles, Davisson and Gill's theory predicted well in the low deflection zone while Poulos' theory agreed well in the high deflection zone. From the probabilistic analysis of ultimate pile capacity, the probability of failure was related to the central factor of safety. The piles usually used in Bangkok area are mainly precast concrete piles

Jan 1, 2010

By Aly M. Mohammad

The 12th and 14th Street Viaducts, which carry Route 139, are located west of the Holland Tunnel in Jersey City, New Jersey. The two viaducts, provide access to and from the Holland Tunnel (which connects New York City and New Jersey) and carry upwards of 50,0000 vehicles per day from Jersey City and New York City to points west. The New Jersey Department of Transportation (NJDOT) selected AECOM to perform design services including rehabilitation and seismic retrofit for the 12th Street and 14th Street Viaducts while maintaining traffic at all times. Building a new parallel bridge just north of the 14th Street Viaduct was essential in avoiding extremely costly traffic delays. Installation of the new foundation, in close proximity to the existing viaduct, required drilling through some of the existing timber piles supporting the bridge. As a result, the existing bridge was required to be reanalyzed for this new foundation configuration. This proposed structure consisted of 8 piers each supported on a single six (6) foot diameter drilled shaft. Currently this portion of the bridge structure has been constructed. The shafts were constructed with rock sockets that were five feet six inches (5?- 6??) in diameter and were extended 11.2 feet (3.4 meters) into rock. A 2300 ton Osterberg Load Test was performed on one production shaft to confirm the capacity of the shaft. The rock socket for the test shaft was in sandstone. This paper will present a description of the design methodology and construction methods adopted for the foundations. In addition, the paper will illustrate the Osterberg Load Test including: equipment used, number and locations of strain gages, and interpretation of results. Additionally, regarding the close proximity of the new foundation, the paper will present the type of equipment used to drill through the existing timber pile foundation while minimizing the impact on the integrity of the existing foundation. We will also present the method of analysis for analyzing the redistribution of load on the remaining piles. The results presented in this paper will assist the design engineer by providing a comparison between the geotechnical design assumptions and the actual measurements obtained by field measurements for this rock formation.

Jan 1, 2009

By Antonio A. Cristóvão, Alexandre Pinto

"Abstract Deep foundations of buildings using driven ductile iron micropiles TRIM solutions, leads to recognized advantages, from technical, schedule and economic points of view. High production rates together with the possibility of using conventional equipment, duly adapted, confer this solution a high versatility.The aim of this paper is to describe the main design criteria adopted for the foundations of the Church ""Nossa Senhora dos Navegantes"" building in Lisbon - Portugal. In addition, results of a full scale load test carried out at site are presented, confirming the adequacy of the solution to the geological and geotechnical scenario, which is characterized by the proximity of the Tagus River Basin as well as the presence of heterogeneous landfill material and alluvial layers of soft clay (muds).1. INTRODUCTION Located on the right bank of the Tagus River, in Lisbon, the new Church building of ""Nossa Senhora dos Navegantes"", patroness of fisherman and navigators, with three or four upper floors, is surrounded by a school and by new residential buildings.The Tagus River basin is known by its alluvial soft soils, achieving, in certain areas, more than 50m meters depth, challenging the construction of new facilities due to the significant unfavorable geotechnical conditions.With a modern an unusual architecture, allusive to the ships used by the Portuguese navigators, the building has a reinforced concrete structure, with one basement and three upper floors. A bell tower with about 40m high, emerging from the structure, marks the landscape with the presence of this religious building (figure 2).For all the reasons previously described, geotechnical engineers play a crucial role on the design of valid foundation solutions, from both technical and economic point of view. Ideally, the solutions adopted should be supported by full scale load tests, performed at site, so that design assumptions could be verified and adjusted on time."

Jan 1, 2014

By James P. Stewart

This case history describes the engineering design and construction for the Contractor of a 35-ft-deep excavation for an 800-square-foot addition to an existing sewage pump station. The site posed unexpected geotechnical complications that included deep gravelly soil, a history of local construction difficulties, groundwater consisting of heavy salt brine, and the need to underpin the existing pump station. The project took an interesting twist when the Owner issued a change order limiting the dewatering discharge to a fraction of that required to lower the water table. This documents the interesting circumstances of this job and documents the unusual subsurface conditions in the Syracuse, NY Lakefront area.

Jan 1, 2003

By Mohammad Nasim

Vertical expansion of existing structures frequently requires foundation retrofitting to enhance the capacity of existing foundations for supporting additional loads. Owing to their small diameter, a variety of suitable drilling methods available for installation, and smaller installation equipment capable of operating under limited headroom conditions, micropiles are often preferred for foundation retrofitting. This paper presents a case history demonstrating application of micropiles to underpin the existing foundation of the Washington D.C. Children?s National Medical Center (CNMC) for its future expansion. Located at 111 Michigan Avenue in northwest Washington, DC, portions of the hospital currently extend five stories above grade and three levels below-grade as parking garages. The hospital intends to expand the surgical wing up to the current build out (five stories) above the remaining portion of the existing parking garage. The original foundations consist of 80-ton Raymond Step-Tapered piles. New loading on the foundations required each Raymond pile to be capable of supporting 150 tons. Results from quick load tests on existing piles indicated that two entire column lines (Column Line A and B) would experience loads beyond their capacity, requiring enhancement of the existing foundation at these locations. The design and construction of the foundation upgrading work was particularly challenging due to various project constraints related to a high groundwater table, micropile installation under limited head room, and ensuring that the parking garage remained fully operational for the entire duration of construction. The paper presents the challenges faced during testing of existing foundations amid a high groundwater table, design developments of underpinning options to support the additional column loads, difficulties and challenges encountered during installation of the micropiles and construction of the micropile pilecaps, and value engineering options developed during various phases of the project. Understanding that micropiles are often a preferred option for foundation retrofitting, the case history is expected to provide a baseline design approach and innovative solutions to typical challenges faced during construction, thereby reducing potential cost overruns during design development and construction of similar future projects.

Jan 1, 2008

By Patrick Bermingham

The advancement of hydraulic impact hammers has followed the general advancement of hydraulics. The construction industry has been revolutionized by the application of hydraulics in excavators, cranes and, of course, in the hydraulic vibratory driver/extractor, which has become a standard tool. The innate ability to move a large mass with a very small displaced volume has given hydraulic power the advantage over previous power mediums. Recent development of more specialized and complex seal configurations and compounds has greatly improved the reliability and permitted the use of higher pressures in hydraulic systems.

Jan 1, 1987

By Dawn C. Tattle

[ ] Panoramic View of Completed Facade Supports The following case history describes the installation of earth retention systems, historical facade supports and structural caissons by Anchor Shoring & Caissons Ltd. at the Air Canada Centre/Raptors Stadium Project in Toronto, Ontario, Canada. The Air Canada Centre/Raptors Stadium project includes a 140,000 square foot office tower, a 20,000 seat basketball arena and their support facilities. The arena within the complex will also have the ability to host hockey, ice shows, concerts and family events.

Jan 1, 1997

By Ryan C. Linthicum

A system of steel sheeting and multiple levels of high capacity double corrosion protected soil anchors were used to restrain a major slope failure that occurred at the base of the Watchung Mountains mid-way through construction of a 650,000 SF retail center along Route 22 in Watchung, New Jersey. The implementation of a design-build earth retaining structure was necessary to stabilize and repair the disturbed mountainside in a timely fashion to permit completion of the retail center on a fast track schedule. The tied back steel sheetpile wall was approximately 2,000 feet long and varied in height from 12 to 25 feet. The hillside extended approximately 350 feet above and 600 feet beyond the wall with the main failure scarp extending 50 feet above and 90 feet beyond. The wall was constructed in a top-down manner and required the installation of 475 anchors to resist loads of up to 70 kips/ft produced by the creeping hillside and groundwater flows from both a series of springs and steady state seepage through an inclined zone of fine sand. Incorporation of a unique tie point connection eliminated the need for a waler, facilitating and simplifying modifications to anchor locations based on anchor load test results and conditions encountered during construction. Post grouting also proved to be an essential element in the successful construction. This paper presents the design and the construction methods used to restrain the significant earth lateral loads produced by a slope failure using steel sheeting tied back with high capacity soil anchors with anchor loads distributed to the sheeting through a unique tie point connection on a fast track schedule. Installation techniques, testing programs, and construction quality control are also discussed.

Jan 1, 2003

By Francis D. Leathers

Four friction pile load test programs, including 23 tension tests and 9 compression tests, have been performed as part of the Central Artery/Tunnel Project in Boston, Massachusetts. The tests, performed on both precast, prestressed concrete (PPC) piles and steel piles, yielded the following adhesion values: [Soil Type Clay Clay Glacial Till Interbedded Sand and Clay Interbedded Sand and Clay Pile Type PPC Steel Steel Steel PPC Adhesion (psf) 610 to 1,200 230 to 900 220 to 550 680 1,280 ] The adhesion appears to be affected by differences in pile material type, with PPC piles having higher adhesion than steel piles. However, part of the apparent difference for the clay may be due to differences in time between driving and testing. The significant range of test data means that the need for site specific testing to determine or verify design values of adhesion should be considered during design. Creep rates at loads near failure ranged from about 0.02 to 0.18 inches per log cycle of time, with most values in the range of about 0.04 to 0.08 inches per log cycle of time.

Jan 1, 1994