Search Documents

By Shamsher Prakash

Estimation of vertical load carrying capacity of a single vertical pile under earthquake loading is an important task of a design engineer. Lateral vibration of vertical pile is highly influenced by the magnitude of vertical load. Several load reversal, during earthquake loading introduce gap between pile soil interface which reduces its load carrying capacity and increases lateral motion. This paper presents a simple time domain numerical scheme to estimate the lateral pile response, considering the loss of contact of pile at pile soil interface, during impact and earthquake loading. The motion of the pile is limited in the vertical plane. Time domain has been discretised into small intervals. The non linearity of soil properties has been taken into account by discretised Winklers model with Wolfes frequency independent mass spring dash pot coefficient for geometric damping. Suitable software has been developed which keeps track of the load reversal point of each elements.

Jan 1, 1996

By H. Mori

Construction of cast-in-place piles with enlarged bases has become popular in the cities in Japan facing to the sea coast, where the subground soil is soft alluvium deposited to depths often exceeding 30 m. The groundwater table is a few meters below the ground surface. Skin friction of piles may become negative due to ground subsidence or reduced due to liquefaction of loose sand during an earthquake. To support highrise buildings, depths of bearing strata to which piles are embedded often exceed 50 m. Due to such geotechnical conditions, methods and equipment to build cast-in-place concrete piles mainly built by the reverse circulation method have been developed since the 1970s. In the first half of this paper, the authors review the cur-rent practise of building cast-in-place piles with enlarged bases. Then they introduce the TFP system developed in recent years, and discuss about the procedures to control and monitor enlarging of bases.

Jan 1, 1989

By K. C. Foye

Use of load and resistance factor design (LRFD) of foundations is growing, from offshore applications to bridge applications and beyond. The development of load and resistance factors for design has traditionally relied on calibration to traditional factors of safety. This technique, however, offers little insight into the challenges of pile design. This paper discusses an approach to LRFD factor development that seeks to isolate the various sources of design uncertainty. Using this approach, reliability analysis is used to develop resistance factors for the design of driven pipe piles in sand. These findings shed light on many aspects of the ongoing discussion of how LRFD can be successfully applied to pile design.

Jan 1, 2008

By Shawn Downey

A helical pile with in-situ grouted shaft was used to underpin the existing slab of a large retail store in the Edmonton, Alberta Canada area. The existing structural slab did not have the capacity to support the increased load requirements. The design to upgrade the capacity specified a drilled shaft as the deep foundation to underpin a portion of the slab. A helical pile was quoted as an alternate and ultimately won the bid based on the advantages of the system. After an ASTM D1143 Quick Load Test confirmed the axial compression capacity, 723 helical piles with grouted shafts were installed in 3 weeks underpinning 40% of the 93,000 ft2 (8,660 m2) building.

Jan 1, 2003

By Cornelis Van Der Veen

Foundation piles, partly passing through unconsolidated compressible layers, suffer a downward drag that is called negative skin friction. The negative skin friction depends on the movement of the surrounding unconsolidated soil relative to the pile and on the friction between pile and soil as a function of that movement. The negative skin friction adds to the load on the pile. However as it is a function of the pile movement relative to the soil, the amount of negative skin friction to be taken into account to determine the allowable bearing capacity depends on the allowable pile settlement. In this paper this property is indicated by the factor µ. As under the conditions of ultimate pile bearing capacity negative skin friction does not occur, a factor of safety is introduced, which is lower than normal. Eventually a formula for the bearing capacity is given in which µ and both figure. The exact values for given circumstances have to be determined empirically. A few examples are given.

Jan 1, 2010

Pier, well cap and steining junction is a complicated 3-d re-ion. The prevalent design procedure for the pier, well cap and steining in isolated manner is not rational. In absence of an integrated approach for design of the junction structure, the well cap is designed uneconomical and at the same time pier and steining are left relatively unsafe. Strut-and-Tie Model based design is a simple solution to this problem. An example illustrating design of the junction structure using STM is presented. On comparison of the outcomes of the STM based design with the prevalent design, the following anomalies are found: i) For smooth flow of forces, length of pier at its base should preferably be made equal to the outer well diameter, ii) STM based design for the pier is more rational, economical and safe. iii) Due to presence of hoop stress, as indicated by the STM, the steining concrete in a depth of p times outer diameter of the well from the well cap level should be limited to M15 grade, iv) STM based design for the steining is more rational, economical and safe.

Jan 1, 1996

By George Onorato, Giovanni Bonita

Deep soil mixing (DSM) has now become a ubiquitous ground improvement technique across the globe for producing soil-cementous materials for many types of complex civil and environmental applications. In the field, the cementation bonds of the soil-cement materials are formed under a confining stress conditions; however, these conditions are generally not considered as most wet grab specimens are cured and tested under ambient atmospheric conditions. This has led to an underestimation of the engineering and mechanical properties of the soil-cement mixed material. This paper presents the preliminary findings of the effect of confining stresses on the mechanical properties of soil-cement mixed samples. This paper discusses the specialized field techniques used for modeling confining stresses during curing and presents the preliminary findings from different soil types. The findings indicate a strength increase within samples cured under a confining stress relative to nonconsolidated samples. The magnitude of the strength increase also appears to be different for different soil types. Finer-grained soils appear to exhibit a larger relative strength increase with confining stress relative to predominately granular soils.

By Hajialilue Bonab M.

The soil-pile interaction under lateral impact loads is not yet completely well known. Many tests on single piles under static lateral loads in centrifuge have been performed and P-y curves have been determined at different levels of the pile in soil. Following these static tests on piles, a large program is undertaken with the same piles submitted to impact loads. The pile equipped with various pile caps has been impacted under variable amplitudes of shock. The behavior of the pile under different impacts was studied and dynamic parameters of the soil-pile system have been determined. Many cases of loading constituting various load histories have been analyzed. They are resulting from parametric centrifuge tests run out, on the one hand with constant and cumulative impacts and on the other hand, variable and cumulative ones. The Influence of each type of loading was studied. Using a finite element method, a non-linear pile-soil system was conceived and a transient dynamic analysis have been performed. The results of the non-linear analysis and experimental data were compared giving a good agreement.

Jan 1, 2002

By Gary L. Seider

Chance, a Division of Hubbell Power Systems, Inc., in conjunction with Sailors Engineering, Inc. has updated its Helical Design Capacity Software. This latest version, ?HeliCAP® v2.0?, is a state-of-the-art helical anchor and pile capacity program designed to operate in the Microsoft® environment. The program calculates the tension and compression capacity along with the frictional capacity, if applicable, of CHANCE® Civil Construction helical anchors and piles using design theories and methods adopted by Chance. This paper details the current state of practice employed by the software in the design methods and installation methodologies of helical anchors and piles.

Jan 1, 2007

By Kirty Dave

Foundations in any contract are the most uncertain parts of the contract and most of the "Construction-Contract-Disputes" are either directly related to foundations or arise as 'Side-effects of changes in promises related to foundations. Foundation Engineering is defined as ' The art of selection, designing and constructing the elements that transfer the weight of structure to the underlying Soil or Rock." (Ralph B. Perk). This art started becoming a science since 1920, when scientific efforts to determine the behaviour of sub-surface materials were made. The art and science merged to give new techniques and the science started dominating the field as more and more refinement came in techniques to predict more accurately the characteristics of the sub-surface elements. Inspite of good thorough investigations and design, the contractual promises drafted could leave some room for differences between the parties and above all the prudency expected of both the parties may fall short of the expectations raised in the contract. This may give rise to disputes which may need to be resolved as per principles of law. This paper attempts to initiate a dialogue amongst Foundations-Engineers and Contractors as to how do we minimise the differences arising out of or related to contracts concerning "Foundations".

Jan 1, 1996

By Bernard H. Hertlein

The introduction of LRFD methods for structural design has been a gradual process by AASHTO, ACI, AISC, ASCE, and the FHWA, which has largely been ignored by the deep foundations industry. In 2007, however, the industry has been obliged to embrace LRFD for any deep foundations on projects involving federal funds. The authors are concerned that the risks caused by the need for, and the difficulty of providing, reliable quality assurance, will result in unnecessarily high safety factors that will defeat part of the purpose of LRFD. A primary attraction of LRFD for owners and engineers alike is that it promises more efficient design, and therefore cost reductions. Unfortunately, a key element of LRFD philosophy is often overlooked - that the applied safety factors can be rationally reduced, often allowing less material to be used, thus saving costs, but only if all the risk factors involved are identified and closely controlled. This means that both the quality of the materials and the quality of the construction work must be adequately monitored, and held to an acceptable standard. In the case of deep foundations, the soil in which the foundation is constructed is also a critical component that must be taken into account in the assessment of risk factors.

Jan 1, 2007

By K. Rama Sarma

Piles are frequently subjected to lateral forces and moments in addition to vertical forces and hence the piles have to be designed for both lateral loads as well as vertical loads. In the design of such pile foundations, two criterias must be satisfied. First an adequate factor of safety against ultimate failure and second, as acceptable deflection at working loads. In this study the work has been carriedout to study the lateral deflection pattern of the pile. The solutions to the problem primarily depend on soil modulus. Equations for computing the values of slope, deflection and coefficients for many types of soil conditions have been developed for static loading for long piles. As analysis part is not available for the above methods for the values of depth coefficients in the tables. It is required to go for linear interpolation which is not valid and highly unreliable. In this present method, coefficients can be obtained for any value of depth coefficient (z) with simple calculation. The present method is very concise and allows one to ana­lyse any type of pile with varying depth coefficient (z) even without the availability of any practical data regarding applied lateral load (P1) and moment (M1).

Jan 1, 1996

By Alan G. MacKinnon

The current piling practices in the U. S. have, to a great degree, been influenced by our founding fathers. When our constitution was written by the delegates from the original thirteen colonies, it was a document of compromise. Generally, the individual states retained their sovereign power over those duties that they had historically performed. The concept of States Rights has been tested throughout our history and has been preserved as of today. An example of the extent of this protection is occurring in the State of Ohio where I currently live. Each of the 50 states receives funds for highway construction from the federal government, approximately in proportion to its population. Congress, when it allocates the funds, quite often attaches amendments to the funding bill to exercise their authority. The major amendment prior to the most recent increase in the speed limit to 65 mph from 55 mph was to increase the legal drinking age to 21 from 18 years old. Embodied within the bill was the provision that the Federal government deduct a percentage from the allocation of any state that did not revise its legal drinking age law from 18 to 21. In the State of Ohio, this change in the law was put to a vote of the people and it was defeated. The federal government now is deducting funds

Jan 1, 1987

By Cen Guoji

The foundation of bored pouring concrete pile have been adopted in the bridge engineering of China since early in the sixties. They demonstrated tremendous technical advantage and achieved notable economic benefit. With improvement of bridge technique including construction technique work equipment, design theory, examination in quality and applicable range etc, the pile diameter became bigger and the foundation changed from shallow to deep-water. This paper examples Jiujiang Bridge of Guangdong in China, which is single-tower cable-staged bridge, total length of 1675m, and expouds adopted successfully the foundation of variable section large bored pile (upper part d=3m, central part d=2. 4m and lower part d=2m) on the conditions of complicated technique that the load is tremendous (it require specially to resist 12000 kN ship impact) and the piles have free length 30m. The paper will be to describle design project and construction practice of pile foundation with variable section, and to compare schemes of equal section pile and pile in sinking-well.

Jan 1, 1991

By Trevor I. Addenbrooke

Stress reducing piles were used for the first time at the Queen Elizabeth II Conference Centre near the Palace of Westminster in London, UK. The inclusion of these piles directly beneath heavily loaded columns was to reduce the high anticipated bending stress in the foundation raft, and to eliminate local yield of the London Clay beneath the column locations. Load cells were placed in one of the stress reducing piles during construction. The data showed that the pile carried about 30% of the column load. This can be contrasted with conventional piled raft design where the pile carries upwards of 80% of the column load. The build up of load on the pile and pile displacement have been accurately reproduced using coupled finite element analysis. These numerical results demonstrate the value of geometrically simple axially symmetric analyses for modelling a pile-enhanced raft. On site, excavation preceded construction of the raft and subsequent pile loading. Failure to model this construction sequence caused the shear strength to mobilize at the base of the pile first, during loading, whereas following the construction sequence caused the shear strength to mobilize at the top of the pile first.

Jan 1, 2002

By E. Ulrich Klotz

It is difficult to predict accurately the capacity of driven piles in sand. In practice, this uncer­tainty either leads to conservative designs if the capacity is under-predicted, or worse, if the capacity is over-predicted, it can lead to severe foundation problems. One significant possible cause of the problem is that currently available semi-empirical design methods do not capture the fundamental mechanisms that govern the load capacity of driven piles in sands. As part of a recent research project at City University centrifuge tests on a driven model pile in sands have been undertaken. A fully instrumented model pile was constructed and pushed into samples of quartz and carbonate sand thus covering a wide range of mineralogies. Tri-axial tests were used to determine the fundamental patterns of behavior of the sands. This allowed a general framework to be established, in which the in situ stress:volume relationship is shown to govern the capacity of the pile. The paper sets out with a brief introduction of the experimental techniques used in the study. The results of the pile tests are discussed in detail with particular attention given to distribution of the radial stresses along the pile shaft. Existing design methods for piles in sand are then discussed in the light of the new understanding gained from the research, highlighting their deficiencies and suggesting an improved approach.

Jan 1, 2002

By Andrew Budek

Reinforced concrete piles are used to carry foundation loads through considerable depths of soil to provide superstructure stability under gravity loads and lateral forces. The creation of cast-in-place (or cast-in-drilled-hole, i.e., CIDH) piles begins with the auger-drilling of a hole of the appropriate depth, into which a cage of reinforcing steel is placed (the cage length is generally equal to the depth of the hole, a construction joint being used to connect the in-ground pile with the superstructure). The pile is then finished by casting with concrete, and the superstructure then appended. The superstructure may either be a column (denoting the structure a pile-column), a column and cap beam, or a footing. Typical pile-column configurations are shown in Fig. 1 (a CIDH pile used in a footing would be similar in overall configuration to Fig. 1(b), with H=0). CIDH piles are well-suited for alluvial soil profiles with a deep water table; such conditions generally allow the auguring of a clean and regular hole.

Jan 1, 2007

By Michael W. Neill, O&apos

The performance of foundations that combine the high bearing capacity of rafts (mats) with the settlement reduction capability of piles is described through a summary of 24 case histories. Structures included are high-rise commercial office buildings, governmental buildings, industrial facilities and residential buildings, and subsurface conditions range from soft clay to stiff soil overlying rock. Pile types are bored, augered and driven. Since piled rafts are not commonly used in the United States, most of the case histories are from overseas. In all cases the performance of the foundations was monitored during and after construction. Particular emphasis is placed on measured settlements of the piled-raft foundations, distribution of resistance between piles and raft, and general analysis methods that were used by the designers for various geotechnical circumstances. Finally, patterns of behavior are summarized. In most cases, the piles were not designed to mobilize their full capacities under sustained loading of the foundation; therefore, under long-term loading conditions, the piles typically carried more load than the raft. This paper is the result of a study conducted by ITC-18 (Deep Foundations, Willem Van Impe, Chair) of the International Society for Soil Mechanics and Geotechnical Engineering by a subcommittee chaired by the author.

Jan 1, 2003

By Jason N. Scott

It is now possible using low-cost wireless technology and rugged hand-held devices to record data on site electronically and for that data to be instantly available to others. This could potentially eliminate many problems that traditionally lead to remedial work, such as poor communication and the late detection of non­conformances. However, determining how best to implement such a system and integrate it with the rest of the business process is far from simple. This paper looks at Stent's experience of these issues by way of a case study of the SHERPA system. This is a wireless site data collection system developed for use with rotary bored piling.

Jan 1, 2006

By Dennis Nottingham

Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971 L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers' experiments, observations and measurements, led to an "H" pile probe design which has produced measured soil density improvements up to 250% using SPT "N60" values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern "Open Cell" bulkhead projects will be presented and discussed.

Jan 1, 2004