Search Documents

By M. F. Gallerneault, V. Fallah, A. Howells, W. M. T. Gallerneault

"The occurrence of recrystallization in cold-worked aluminum sheet during the brazing process leads to loss of strength, an inhomogeneous grain structure and reduced corrosion resistance. AlMgScZr alloys are known for their extraordinary recrystallization resistance due to the influence of Sc and Zr addition on their microstructure. Here, we investigate the effect of alloy composition (i.e. Mn, Mg, Sc, Zr content), cold-roll reduction and pre-aging treatment on the recrystallization behavior of cold-rolled sheets at brazing temperatures typically used during the manufacture of heat exchanger units. The analysis of recrystallization behavior is carried out through microstructural characterization and the results are compared with the behavior of a commercial, AA3xxx-based heat exchanger alloy.INTRODUCTION Control of recrystallization is of critical importance during brazing, which is a widely-used joining technique for aluminum alloys in aircraft structures (Heinz, 2000) and automotive heat exchangers (Miller, 2000; Marshall, 1993). Due to excessive local heat at brazing temperatures, the cold work texture of aluminum alloys in the cold-rolled sheets may undergo a local recrystallization process (Marshall, 1993). This leads to the formation of an inhomogeneous microstructure and thus anisotropic mechanical properties (Miller, 2000) and low corrosion resistance (Marshall, 1993) across the sheet. X800, a commonly-used Al-Mn alloy series for automotive heat exchangers applications, has been developed specifically for a higher strength as well as an enhanced corrosion resistance as opposed to the traditionally-used AA3003 alloy (Marshall, 1993). X800 alloys, however, exhibit a low recrystallization resistance at normal brazing temperatures, i.e. 590°C. In contrast, Al-Sc-Zr alloys have been shown to exhibit an extraordinary recrystallization resistance at such temperatures (Riddle, 2004) while also being corrosion resistant and possessing a high room-temperature strength (Fuller, 2002). This has been shown to be due to the formation of coherent, nanoscale Al3(ScZr) precipitates that effectively impede grain boundaries while also exhibiting very slow coarsening kinetics at high temperatures (Riddle, 2004; Jones, 2003; Ocenasek, 2001). In this study, we analyze the recrystallization behavior of X800 alloys under brazing conditions through introducing Sc and Zr into the system as well as varying the Mn and Mg content. The effect of processing route is also studied by introducing a pre-aging stabilization treatment as well as varying the cold-roll reduction prior to the final brazing anneal."

Jan 1, 2018

A line of nine self-aspirating W emco cells, part of the Rougher circuit at Division Salvador, Codelco Chile, was retrofitted to allow operation with forced air. Each cell could be operated self-aspirated or with compressed air supplied through a 4-inch line equipped with a mass flow meter. Gas dispersion was characterized for the two modes of operation. Metallurgical performance was compared under self-aspirated conditions and with different gas profiles under forced air conditions. Cell characterization demonstrated that with forced-air the cells could not evenly distribute air across the cell volume. Bubble size increased with gas velocity, as expected, with no difference between self-aspirated and forced-air operation. A systematic increase in bubble size down the bank was found. Cumulative bubble surface area flux down the bank showed no major differences between surveys. However, grade-recovery curves revealed that the highest recoveries were invariably obtained with forced air operation. Plotting concentrate mass recovery vs. enrichment ratio showed that the line performance could be controlled over a wider range when forced air was used.

Jan 1, 2007

By Li Chongyang, Liu Baolan, Jia Xiaolin, Li Suping

An Al/Al2O3 gradient coating applied on a heat-resistant stainless steel was prepared through a slurry process by using aluminum and ?-Al2O3 powders as the transition filler material, alpha alumina as the surface coating material, aluminum dihydrogen phosphate as the binder, and sodium molybdate as the corrosion inhibitor. The effects of heat treatment temperature, adhesive/filler ratio and ?-Al2O3 content on the bonding strength, microhardness and thermal shock resistance were investigated. The crystal phase and microstructure were characterized by XRD and SEM. The results indicated that the composition of the coating changed continuously from surface to coating-substrate interface. The coating could offer high bonding strength and good thermal shock resistance when heat treated at 700°C.

Jan 1, 2010

By M. J. Nicol

The leaching of gold with thiosulfate solutions in the absence of ammonia and copper ions was investigated using electrochemical and kinetic methods. In sodium thiosulfate solutions, the electrochemical oxidation of gold was hindered and the leaching rate using pure oxygen as the oxidant was very slow. It was found that the addition of a small amount of thiourea or formamidine disulfide to the thiosulfate solution greatly enhanced the oxidation of gold. However, the enhancement to the overall dissolution of gold using dissolved oxygen as the oxidant was limited. This was attributed to the fact that the oxygen reduction process was unaffected by the additives and remained slow, which limited further improvement to the overall kinetics. An alternative oxidant, the ferric EDTA complex having a reduction potential of approximately 0.12 V, was found to be promising. The cathodic reduction of ferric EDTA was fast and reversible at neutral pH. While the ferric EDTA complex was effective in oxidizing gold, it did not appear to significantly oxidize thiosulfate. A thiosulfate solution containing thiourea and ferric EDTA has been shown to quickly dissolve gold in the form of a powder as well as from gold ores. In the leaching with the ores high gold recoveries of above 90% was achieved with the best performance obtained in neutral solutions (pH 6-7).

Jan 1, 2005

By T. Negeri, M. Boisclair

"A hybrid process consisting of flotation and magnetic separation has been developed to concentrate multi-phase rare earth minerals associated with a carbonatite ore that contains a significant amount of niobium. Fine grinding to a d80 of <65 microns was required to obtain acceptable separation of 92% of the contained total rare earth oxide (TREO) and niobium in half the feed mass. Whereas it was possible to obtain 85% of TREO in 28% of the feed mass through staged cleaning, it was demonstrated that at least 87% and 85% recoveries of TREO and Nb respectively could be achieved in 16% of the feed if the rougher-scavenger concentrates were calcined, quenched, reground to <25 µm and then magnetically upgraded. The paper discusses the overall concept of the flowsheet and the experimental strategies that led to this progress. INTRODUCTIONOut of the approximately 250 minerals known to contain rare earth elements (REEs), only about 60 of them contain REEs in significant amounts. Over 95% of the world’s rare earth oxides (REOs) are believed to occur in the form of three minerals (Pradip & Fuerstenau, 1991) namely bastnaesite (Ce,La,Y)CO3F, monazite (Ce,La,Nd,Th)PO4 and xenotime Y(PO)4. An estimated 51.4% of global REO resources are hosted by carbonatite deposits with the same three minerals as major constituents (Weng et. al., 2015). Any one of the REEs or commonly all of them can be found in these minerals (Ravnaas, 2010). As the demand for critical REEs increases due to the ever increasing applications in advanced technologies, many deposits containing other forms of REE minerals will have to be developed. REE minerals are extensively dispersed and intergrown with several oxides, silicates, carbonates, and phosphate minerals. Consequently it is possible to liberate them only at fine grinding and is thus difficult to separate and produce high grade rare earth mineral concentrates. Most of these minerals contain other important elements such as tantalum (Ta), niobium (Nb), uranium (U), and thorium (Th) in varied quantities. REE minerals in the same ore may exist as carbonates, fluorocarbonates, niobates, silicates, phosphates etc. in association with gangue minerals belonging to different mineralogical groups."

Jan 1, 2016

By M. Pearson, W. Bristowe, A. Hanson

"There&apos;s no such thing as quality assurance; only quality control ... by inspection. "(1) A common misunderstanding in the procurement and construction of custom designed, fabricated pressure vessels and piping systems is that quality assurance can be achieved by simply referencing codes, standards, ISO 9002, QMS or other such programs in the contract documents. In the authors&apos; experience, nothing could be further from the truth, not detrimental to the performance of the equipment than the exclusion of inspection activities and reliance upon warranties and "fit-for-purpose" clauses. Likewise, the expectation that fabricators, suppliers, or third party inspectors can provide such assurances is also unrealistic where they have limited knowledge of the process, material selection criteria, or limited technical resources. The development and successful execution of a quality assurance program is a collaborative effort by engineers, designers, material suppliers, equipment fabricators, and field inspectors with the full understanding and support of the end user.This paper presents an outline of the quality control activities undertaken by the authors for several recently completed and on-going hydrometallurgical projects. The activities include: prequalification of fabricators and sub-vendors, shop audits, material validation testing, material source control and verification, positive material identification of weld metal overlay, specialised welding inspection, contamination control for titanium and titanium-clad fabrication, eddy current and mass spectrometer (helium) leak testing of shell-and-tube heat exchangers, hot cycle testing of titanium clad equipment, tolerance verification for refractory lined equipment, final inspection and cleaning.

Jan 1, 2004

By L. R. P. de Andrade Lima, D. Hodouin

The paper presents a survey of the possibilities of the simulation techniques for improving the design and operation of gold processing plants. The procedure to construct kinetic models that are used in simulators is first reviewed, and examples are given for cyanide gold dissolution and gold adsorption on carbon. Then, an overview of the structures of the plant simulators is proposed, and the simulation equations formulated for a carbon-in-leach process. Finally, the potential of simulation methods is illustrated by four examples. The first one shows how it is possible to use a simulator to design a cascade of leaching tanks while optimizing an economic performance criterion. The second one illustrates the role of simulators for optimal tuning of the cyanide addition strategy in a leaching circuit. The third example focuses on the power of simulation to design carbon transfer strategies in a carbon-in-pulp process. Finally, the last example shows the role of on-line simulators for optimally supervising the automatic control of cyanide addition into leaching tanks.

Jan 1, 2005

By T Nakamura, M. Itoh

Most of the used cathode ray tube (CRT) glass in Japan, which contains lead oxide, was exported and recycled in overseas factories of new CRTs. However, domestic treatment and recycling of waste CRT glass has become necessary because overseas CRT factories have shut down and exports of CRT glass have stopped. Some of the waste CRT glass recycled domestically is charged in lead blast furnaces instead of silica flux, because there is no local reproduction route for glass that contains lead. However, the mass of CRT glass that can be treated in this manner is limited because of its high silica content. Consequently, additional treatment methods for waste CRT glass are required so that more can be used as a lead smelting material. In this study, waste CRT glass was treated with hydrofluoric acid to dissolve the silica contained in the glass, and the dissolved lead was recovered by precipitation. Lead metal was recovered by electrodeposition from the prepared hexafluorosilicic acid solution.

Jan 1, 2011

The morphology of environmentally assisted cracks in stressed pipeline steel has been investigated, For a dilute and neutral solution (NS4) simulating ground water in contact with the steel, semi-elliptical cracks grow faster on the surface (2c) than in the depth (a), hence, the aspect ratio (a/c) decreases, This is explained using a deterministic concept since corrosion is dominant and the primary constraint is the conservation of charge, By contrast, when mechanistic conditions prevail, significant growth occurs in the depth, When underloads are imposed in the loading history, temporary accelerations in crack growth occur because corrosion rather than mechanical effects become dominant.

Jan 1, 2005

By A. Plumtree

The morphology of environmentally assisted cracks in stressed pipeline steel has been investigated. For a dilute and neutral solution (NS4) simulating ground water in contact with the steel, semi-elliptical cracks grow faster on the surface (2c) than in the depth (a), hence, the aspect ratio (a/c) decreases. This is explained using a deterministic concept since corrosion is dominant and the primary constraint is the conservation of charge. By contrast, when mechanistic conditions prevail, significant growth occurs in the depth. When underloads are imposed in the loading history, temporary accelerations in crack growth occur because corrosion rather than mechanical effects become dominant.

Jan 1, 2005

By R. J. McCarthy

In-pit Crushing and Conveying (IPCC) is increasingly being considered by mining companies as a means to reduce their dependence on trucks and thus, fuel, tires, labour, etc. There is potential for great savings in operating costs which ultimately can mean better economics for a mining project. Vale has considered the application of IPCC at its Moatize coal project in Mozambique. Up to three studies have been conducted with the latest, at a pre-feasibility level, showing some promise. This paper explores the mine planning and IPCC engineering elements required in an IPCC study, their application to the Moatize project, and the drivers which most impact the viability of IPCC at Moatize.

Aug 1, 2013

By A. Liem, R. L. Johnson, C. Sturgess, E. Kuzub

New challenges in mineral processing arise as high-grade ores become less available and the mining industry is forced to exploit lower grade ores. One of the challenges in beneficiating lower grade ores is the liberation of mineral particles while maintaining control over material management. Lower grade ores need fine grinding to free valuable minerals, but finely divided particles can cause severe problems, such as dustiness and flowability, in subsequent stages of material management. There are at least two approaches that can be taken to resolve this dilemma, both of which relate to particle size enlargement. First, the application of a dust suppressant can be used to control that aspect of material management. The optimal choice of dust suppressant agent depends on effectiveness and cost, both of which can be strongly influenced by the selection of application method. Second, agglomeration combining small particles into larger units-can reduce dust and improve the flow characteristics of the material at the same time. There are several mechanisms that can be employed to agglomerate mineral materials. Although agglomeration adds a new processing step, it is often cost effective. This paper describes these two approaches and their respective challenges, as they relate to a mined ore. We report on modified or newly developed procedures for characterizing mineral ores with respect to material management. On the same material, we use agglomeration processing to capture fines within larger particles and show how dustiness and other aspects of material handling are affected. We conclude by discussing their specific application in accordance with the mineral properties and processing needs.

Jan 1, 2004

By R. P. Hackl, P. G. West-Sells

Carbonaceous gold ores are particularly attractive for leaching by ammonium thiosulfate as the gold thiosulfate complex is not significantly adsorbed by the organic carbon present in the ore. A technically and economically feasible process for treating these ores with ammonium thiosulfate has been developed. In this process, gold is extracted by leaching the ore with ammonium thiosulfate, the solution is separated from the ore by counter - current decantation, the gold is recovered by precipitation with ammonium sulfide, and finally the gold containing product is upgraded by reacting the elemental sulfur present in the precipitate with ammonium sulfite. The precipitation filtrate is recycled back to the grinding step to close the solution balance. Reagent consumption is not excessive. Besides precipitating gold, the precipitation step removes most deleterious solution impurities and converts a portion of the polythionates back to thiosulfate. This paper discusses the optimization of the leaching, precipitation, and upgrading steps. The results of a 10 kg/h pilot plant campaign are also discussed.

Jan 1, 2005

By D. Larouche, M. Mardan

Hot tearing is a complex defect in aluminium castings which is produced during solidification when a certain amount of liquid phase remains and weakens tensile resistance of the alloy. In direct chill casting of aluminium alloys, hot tears initiate at the surface of sheet ingots just after the primary cooling zone, where the microstructure is particularly vulnerable. In order to study the hot tearing susceptibility of these alloys, and the effect of grain refiners on their thermo-mechanical behavior , tensile tests were carried out in the semi-solid state ( ~95% solid) and at low strain rates using an apparatus called DCSS, for Direct Chill Surface Simulator. This apparatus, originally developed at Alcan Arvida R&D Centre (ARDC), is an instrumented rig test reproducing the conditions prevailing during the primary cooling stage of the DC casting process. The mechanical behavior of solidifying shells and the hot tear formation under applied tensile loads were measured and the occurrence of hot tearing was observed. Temperature in different locations of the casting, applied load and surface strain were monitored during the tensile tests conducted on aluminum alloys AA5182, AA6111 and AA3104. The microstructure of the tested samples was examined using the optical microscope to evaluate their columnar or equiaxed aspect and their effect on the mechanical response of the alloy. A special emphasis has been given to the evaluation of fractions solid existing in the castings at the start of the tensile tests, taking into account the local temperature, thermal gradient and cooling rates experienced. It was found that excessive grain refiner additions decreased the strength of solidifying shells because of the increased level of porosity induced by easier nucleation of new phases (gas included). It was also observed that cooling rates increased with the level of grain refiner, a phenomenon that was associated to the higher number of contact points obtained with small equiaxed grains. Finally, the concept of a stress based criterion for hot tearing was reinforced by the strengths obtained on not grain refined AA5182 and AA6111 showing similar fraction solid near the surface, but significantly different grain sizes.

Jan 1, 2006

By W. Basuki, B. Setyotomo, L. Hakim, R. Hendrajaya

Due to high crack sensitivity of slab product of gas and oil line pipe application, its steel making process and alloy composition were evaluated and then improved to overcome its critical solidification process and reduced surface defects. The study was conducted at Slab Steel Plant Krakatau Steel. The purpose was to improve slab surface quality by reducing surface defects so that the slab surface doesn&apos;t need to be totally repaired. The method applied was by performing plant trial process, which the secondary process parameters such as alloying method and the casting parameters such as casting powder selection, metallurgical cooling, mould level control, and superheat were continuously monitored and then adjusted to the surface quality of the product. Based on the calculation of Ferrite potential of the steel, the chemical composition was designed to achieve optimum casting parameters in order to avoid high shrinkage during solidification. The results of the study are decreased surface defect quantity, and smooth casting process. The quantity of crack decreased by almost 90%. The slab surface repairing was significantly reduced from 85. % to less than 10%. These new casting parameters and developed alloy composition are then used and standardized for the mass production of the steel.

Jan 1, 2005

By Arnfinn F. Prugger, Fritz F. Prugger

"The Saskatchewan potash beds are overlain by a number of water-bearing formations. There are water zones in the footwall as well. These aquifers created difficulties during the construction of shafts to the potash beds at 1()(}() m depth, and they pose a continuous threat to the safe and efficient operation of potash mines in the province.The first shafts to be sunk in Saskatchewan encountered major problems during shaft sinking. Of the 17 potash shafts started in the province, five had major water inflows during shaft sinking or after production startup, and one was abandoned because of water problems. The biggest obstacle encountered during shaft sinking was a poorly consolidated sand-shale-clay-siltstone unit commonly called the Blairmore Formation, which occurs at a depth of about 500 m. The initial problems with shaft sinking were overcome in the 19605by using European methods of freezing and the installation of cast-iron tubbings or a double-steel lining through water bearing horizons.From the start of production in the early 19605, operators have been aware of the ever-present hazard of potential water inflows into mine openings from permeable units in both the hanging wall (carbonates of the Dawson Bay Formation which occur 15 m to 50 m above the mining level) and the footwall (carbonates of the Winnipegosis Formation which occur 50 m to 150m below). This awareness has been reflected in conservative over-all extraction rates and mining layouts specific to local conditions. In spite of this consciousness, a number of water problems have occurred in operating mines. These have resulted in everything from simple increases in expenditure to the shut-down of one mine in 1987.In this paper a history of water problems in the Saskatchewan potash industry is given, followed by a summary of measures that are now commonly used to avoid these problems. A description of each inflow event is given, and the attempt is made to analyze the causes of each occurrence. Based on what was learned f rom each event, suggestions are made to prevent future water inflows into potash mines."

Jan 1, 1991

Gold recovery from refractory ores can be very difficult and complicated depending on the causes of the refractoriness. Typically, a fine wind and/or the oxidation of the gold-bearing sulfide minerals are required to liberate gold from the host rock matrix. Mineral separation techniques, particularly surface¬wettability based separation (i.e., flotation) and magnetic separation, can be used to pre-concentrate the gold and sulfide minerals, or to remove mineral species that are harmful either to the oxidation of the gold-bearing sulfides or to the cyanidation following the oxidation. In this paper, several processes are described, including oil-agglomeration flotation recovery of fine-grained gold and sulfide, reverse flotation of carbonate minerals prior to pressure or bio oxidation, reverse flotation of elemental sulfur after pressure or bio oxidation but prior to cyanide leaching, and magnetic concentration of gold-bearing iron oxides. The integration of these techniques with gold hydrometallurgical processes may make the economic recovery of gold from an otherwise uneconomic refractory ore possible.

Jan 1, 2011

By Derek H. C. Wilton

"The Cape Ray Fault Zone of southwestern Newfoundland contains two notable electrum/ base metal sulphide quartz vein lode occurrences hosted by two contrasting lithological units, viz. a graphite schist horizon and a granite. The two occurrences, although in proximity, are not in direct contact, but, based on geochronological, geochemical and isotopic evidence, they were apparently deposited from hydrothermal fluids generated as a vapour phase from the magmatic progenitor of the Windowglass Hill granite.This paper provides further evidence, from REE and background A u and Ag data, for the magmatic origin of the hydrothermal fluids. Wall rocks to the electrum-bearing quartz veins in both the schists and granite have experienced a LREE depletion probably due to leaching by Cl-bearing solutions. Gold and silver contents are typically low in all rock types but there is a slight elevation in gold concentrations in those units in contact with the Window glass Hill granite. The granite also has the relatively highest gold and silver contents of any unit in the region.IntroductionThis paper presents the evidence from rare earth element (REE) and gold/silver concentration data for the magmatic origin of hydrothermal fluids responsible for deposition of the Cape Ray electrum deposits of southwestern Newfoundland. The two deposits occur in the Cape Ray Fault Zone (Fig. I) within the Windsor Point Group and Window glass Hill granite. The larger occurrence is called the Main Shear Showing and consists of a deformed quartz vein horizon, which extends for - 6 km, within the late Devonian Windsor Point Group. This unit is an intermixed ignimbrite and mafic tuff sequence with associated schists (metasediments) and gabbros. The host rocks to the mineralized quartz veins are interleaved graphite, chlorite and sericite schists. Basal ignimbrites within the Windsor Point Group have been dated, by Rb/Sr isotopic methods, at 377 ±21 Ma (Wilton, 1983a). The basal ignimbrites also have enriched REE patterns, an elevated initial Sr ratio (0.709) and a peraluminous-siliceous nature which suggest they resulted from the partial melting of continental crust (Wilton, 1984)."

Jan 1, 1985

By Nabeel Khan

Annual oil production from the Canadian Oil Sands in Northern Alberta has been rising for several decades, and more ore and overburden are excavated each year from an increasing number of open pit mines. Overburden meeting certain specifications will be used to dam tailings and fill open pits, but the remaining material must be stored in overburden storage structures (OBSS). Well-designed overburden storage structures are more stable and cost less in the short- and long-term. The purpose of this paper is to explore OBSS designs that will be stable yet economical in the short- and long-term. The geological background of the site is briefly discussed, including the effect of each of the main geologic layers (recently deposited till and muskeg, Clearwater Formation clay shales, McMurray Formation oil sands, and the Devonian limestone) on the slope stability of the OBSS. Cost is considered in the analysis when balancing between minimizing costs (steeper slopes) and acceptable factors of safety (flatter slopes), all the while considering the financial consequences of failure. Potential failure planes are identified and probabilistic analysis is conducted on the critical failure surface. The variations in the factor of safety caused by varying pore water pressure, friction angle, and cohesion, are plotted and discussed.

Jun 1, 2012

By Doug Ashbury

Diamond Miners? Challenges ? Remote ? 300 kilometres from Yellowknife ? Sub-Arctic conditions ? permafrost, climate ? No power ? No all-weather roads ? Ore bodies difficult to find ? Caribou, fish of special concern ? Communities with low education, little experience, but high expectations ? Major investment required ? Diavik C$1.3 billion

Apr 1, 2005