Search Documents

Strips of AA6111 automotive alloy were cast on a horizontal single belt strip casting simulator, Pure copper and carbon steels substrates plasma sprayed with different coatings for improving the strip surface quality, were used as chill moulds, Experimental studies revealed that a graphite coating provided the greatest benefit in achieving good surface quality. The interfacial heat fluxes during solidification of AA6111 strip were calculated by the IHCP method (Inverse Heat Conduction Problem). Temperature variations and cooling rates within the strips were then calculated through numerical simulations based on the time-dependent heat fluxes obtained by IHCP, The effects of casting parameters, including casting temperature and strip thickness, on interfacial heat fluxes, cooling rates and microstructures, were investigated, Although the maximum interfacial heat fluxes on the chill copper substrate were much higher than the results obtained from the steel substrates, the solidification times of the melts were mainly determined by strip thickness. Very fine equi-axed grains were obtained for both 1.2mm and 2.5mm thick strips thanks to the rapid extraction of heat, and effective grain refinement.

Jan 1, 2005

By V. A. Leão, M. L. M. Rodrigues, L. C. Sicupira, I. C. B. Rodrigues, T. C. Veloso

Brazilian sulphide ores can contain a significant content of chloride and fluoride, which are harmful to bacteria and thus bioleaching. This work summarizes a four-year research investigation on the effect of fluoride on both bacterial growth and sulphide bioleaching, supported by studies carried out with secondary copper ores. Firstly, the influence of fluoride on the kinetics of ferrous iron bio-oxidation with Sulfobacillus thermosulfidooxidans was addressed. Values as low as 10.0 mg/L F- fully inhibited bacterial growth, although fluoride toxicity could be overcome by the presence of aluminium, which reduced the concentration of hydrofluoric acid through the formation of aluminium-fluoride complexes. This required at least a 2:1 aluminium/fluoride molar ratio, which ensured bacterial growth rate values similar to that observed in the absence of fluoride ions. Subsequently, both batch and column bioleaching with mesofiles (30 ºC), moderate thermofile (50 ºC) or hyperthermophiles (67.5 ºC) of two secondary copper ore samples were analyzed with focus on the relevant effects of fluoride-containing minerals on the bioleaching of such sulphide ores.

Jan 1, 2014

By Y. Wang

Phosphates and fluorides are used as regulators for the removal of silicates from diasporic-bauxite both in direct and reverse flotation. While using dodecylamine chloride as a collector, micro-flotation studies showed that sodium hexametaphosphate has stronger depressing power on diaspore than on silicate minerals with increasing sodium hexametaphosphate concentration at pH 6.5, but sodium fluorosilicate shows poor depression on diaspore with increasing sodium fluorosilicate concentration at the same pH. Zeta potentials of diaspore and silicate minerals become more negative both in the presence of sodium hexametaphosphate and sodium fluorosilicate. Adsorption density studies indicated that the adsorption density of sodium hexametaphosphate on diaspore is much higher than that on silicate minerals at the concentration of 75 mg/L. FTIR spectroscopy studies show that sodium hexametaphosphate interacted with the Al atoms exposed on the diaspore and silicate minerals surfaces to form P?O?Al bonds through the P02 groups. It is possible that sodium fluorosilicate interacted through F- or [SiF6]2- with silicate minerals surfaces based on the analysis by AES.

Jan 1, 2006

By Martin Encinas, Jesús L. Valenzuela, Jose R. Parga, Salvador Aguayo, Roy G. Lewis

Continuous laboratory solvent extraction of gold from cyanide solutions using LIX?79 guanidine based extractant has been investigated. Different variables that affected the selectivity and extraction include aqueous pH, extractant concentration, and modifier concentration. The extraction isotherms of the aurocyanide complex with respect to the other cyano anions were compared, and the following order of selectivity Au > Ag > Zn > Cu > Fe was observed. According to the pH isotherms, aurocyanide can be extracted in an alkaline media, and a better separation with respect to the other cyanoanions was obtained in the pH range 10.5-11.2. From the McCabe Thiele diagrams, better recovery was predicted when using LIX?79 extractant and tridecanol modifier at 10 vol.%. Stripping of the gold from the loaded organic was carried out at pH > 12 using NaOH and NaCN solution. The continuous tests indicate that a two-stage extraction followed by a single stage strip is adequate to obtain an overall process efficiency of >90%. Better results were obtained using a copper wash stage before gold stripping.

Jan 1, 2014

By Z. F. Lodhi, J. H. W. De Wit, H. A. Terry

Zinc and its alloys have been extensively used as replacements for Cadmium coatings in aeronautical and automobile industries. Zn alloys with low Co or Fe have been highly investigated but coatings with higher amount of Co are very difficult to achieve due to anomalism associated with these coatings. Anomalous Zn-Co-Fe alloy is a relatively recent addition to the family of Zn alloys. It is found that the addition of Fe in the electrolyte assist in overcoming the anomalism. In this research Zn-Co-Fe alloys especially with higher amount of Co (>15%) and Fe (~1%) are investigated, after overcoming the anomalism associated with its deposition, and the corrosion resistance is compared with pure Zn and Cd. It is found that an increase in Co to higher than 25 % accounts for a shift in the OCP to a level near Cd yet keeps it electronegative to steel. The coating shows superior corrosion resistance, in terms of its sacrificial and barrier properties in 3.5% NaC1 as compared to Zn and Cd.

Jan 1, 2006

By Rodney Trevor Jones, Arthur Robert Barnes

Anglovaal Minerals acquired the Nkana slag dump from Zambia Consolidated Copper mines (ZCCM) in 1998 and embarked on an ambitious project to pioneer the recovery of cobalt from slag using DC smelting technology. Anglovaal Research Laboratories performed initial pioneering smelting tests in a 250 kW DC furnace over a 3-year period before engaging Mintek for three piloting campaigns at the 1.5 MW level. Mintek had previously developed a reductive smelting process, patented in 1995, using a DC arc furnace for the recovery of cobalt from slags. The results of the pilot-plant test campaigns were used as the basis for engineering the commercial 40 MW operation installed at Chambishi Metals plc in Zambia in 2001. This paper traces the development of understanding of the metallurgical fundamentals ultimately used to predict furnace performance, reviews some of the extreme technical challenges faced, how solutions were identified and highlights some of the critical issues identified during piloting and how these impacted both positively and negatively on the final commercial operation.

Jan 1, 2011

By H. Somekawa

The fracture toughness and deformation structures an AZ31 magnesium alloy processed by equal-channel-angular extrusion (ECAE) were investigated. The average grain sizes of as-ECAE and annealed-ECAE alloys were 4.0 and 16.3 µm, respectively. The plane-strain fracture toughness, Kip, in as-ECAE and annealed-ECAE were estimated to be 27.3 and 23.5 MPam1/2, respectively, by stretched zone analysis. The fracture toughness indicated higher value with grain refinement. From optical microstructural observations in samples after fracture toughness tests, although deformation twins were observed in annealed-ECAE, no deformation twins were observed in as-ECAE. From TEM observations, the dislocations on basal and non-basal planes were activated in as-ECAE. With grain refinement, the activations of dislocations on both basal and non-basal planes were possibly related to the reduction in formation of deformation twins in as-ECAE. In addition, in comparison with direct extruded process, ECAE process was more effective method to improve the fracture toughness in magnesium alloys.

Jan 1, 2006

By Greg Johnson

Maintenance needs information about assets to optimize availability and production needs information about performance and consumption to maximize output. In considering both these needs together as, ?Asset Optimization?, the information systems that support them are critical. The theory of Asset Optimization derives from the Lean Manufacturing concepts developed by Toyota, but some changes are required to apply this to mining operations. In particular, mining operations require automated systems due to their geographic spread and they need a strong emphasis on capturing under-performance losses as well as delays and stoppages in production. Leading metal miners and coal miners alike have applied these systems to good effect in the last 10 years. The concepts developed initially in minerals processing plants are now being applied to the mines themsleves as well as the mining logistics chain. Production increases of 5?10% are achievable with the right implementation and consideration of the some key lessons learnt in the last 10 years. Putting these lessons into action is one key step in the goal of optimizing asset performance and thus utilizing the resource at lowest cost.

Aug 1, 2013

By G. Gagnon

"HistoryMining of the Schefferville iron deposits began in 1954 on completion of the 357 mile railway linking the mines and the St-Lawrence river port of Sept-Iles. Apart from crushing, no treatment of these ores was required before smelting. In the late 1950's, testwork began at schefferville to develop a process for upgrading the extensive lower grade deposits containing 51% iron with 15% silica (natural analysis). Engineering for a six million ton per year beneficiation plant using cationic silica flotation and the A-C grate kiln Began in 1970 and the first pellets were produced in mid-1973.Production requirements and operating difficulties have restricted capacity to approximately 85% of design but on going improvements are being made continuously to attain design capacity.GeologyThe sedimentary ore bodies of the labrador trough occur in a belt 5 to 10 miles wide and 60 miles long and contain 51 individual deposits varying in size from 1 and 60 million tons. The ores are classified into three main color groups."

Jan 1, 1981

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Froth depth or interface level is an important control variable in column flotation which can influence both grade and recovery. A common method of locating the level is based on sensing the hydrostatic pressure at one or more points along the column. The level indicated can be in considerable error, largely because of variations in froth and collection zone bulk densities. A portable conductivity probe has been developed to detect the position of the interface from conductance measurements across the interface. The location of the interface corresponds to the position where a large change in conductance is observed, which is primarily a consequence of the difference in gas holdup between the collection and froth zone. This probe detects the position of the interface to an accuracy of ± 5 cm. The probe can be used while the column is in operation, which allows for on-line recalibration of the level detection system. Results obtained in its application in a pilot-scale column (0.91 m in diameter) are described.

Jan 1, 1990

By J. W. McCammon

CRANGES in construction ideas and the continually rising costs of labour and conventional building materials, particularly since World War II, have prompted widespread investigations into the development and adaptation of new materials to meet the new requirements and to help reduce costs. Lightweight aggregates have been prominent in these investigations. The lightweight aggregates most commonly used today are foamed slag, cinders, pumice, diatomite, exfoliated vermiculite, expanded perlite, and bloated clay or shah. Lightweight aggregates contribute to the building industry in several ways: ( 1) in large structures the reduction in deadweight effected by the use of lightweight materials reduces the amount of reinforcing and structural steel necessary to support the structure; ( 2) the decrease in weight of lightweight blocks makes handling easier and faster; (3) pre-fabricated floor and roof slabs and tilt-up walls of lightweight concrete have become feasible and popular; ( 4) lightweight aggregate concrete has good nailability and is easily channelled; (5) concrete and plaster made with lightweight aggregate have good heat and sound insulation properties.

Jan 1, 1957

By Michel Carreau

Renewable assets have large upfront capital costs but minimal operating expenses over their lifetimes. In some instances, deals can be structured so that direct capital investment is feasible, with paybacks typically within 5-7 years. In others, the burden of renewable CAPEX must be removed in order to create an attractive alternative to fossil-fuel-fired generation. Hatch has designed and oversees the construction of a renewable installation, which is financed, owned and operated by a special-purpose entity. Renewable energy is then delivered to the mining company via a customized power purchase agreement at a price that is lower than the levelized cost of fossil fuels. In this way, the mining company removes the burden of the renewable energy CAPEX from its balance sheet, thus freeing up capital, decreasing risk, and making the predictable, lower cost of renewable power more attractive than the variable cost of fossil fuels. This paper presents the above business model and success stories of hybrid power at remote sites (wind and solar coupled with diesel engine).

Aug 1, 2013

By R. Therrien, L. Gosselin, J. Raymond

ABSTRACT: The ground-source heat pump is a low-carbon technology that uses the earth’s renewable geothermal energy to heat and cool buildings, with an ef?ciency 3 to 4.5 times that of conventional systems. These high performances are achieved by exchanging heat with the earth using a ?uid that is groundwater, surface water or closed loop water. Expensive installations, such as water wells or buriedcoils, are however necessary to transport the ?uid in and out of the earth, making ground-source heat pumps more costly than conventional systems. Installation costs can be reduced in mining environments due to the abundance and the accessibility of resources to be used with heat pumps. Examples of system design calculations using data from the Mouska and Doyon mines in Abitibi show signi?cant installation cost savings using dewatering mine water or ground heat exchangers installed below oxidizing waste rocks. Ground-source heat pump technology is reviewed and scoping calculations are presented to illustrate how such systems can be installed in mining environments.

Jan 1, 2010

By Robert S. G. Chapman, Kieran M. J. Downes

The Sulphide-Preview Lakes area is located 45 km northeast of La Ronge in northern Saskatchewan. It lies within the southern portion of the Proterozoic La Ronge Volcanic-Sedimentary Belt. Two styles of gold mineralization are present in the Sulphide Lake area , stratabound gold mineralization is intimately associated with a pyrite-pyrrhotite-arsenopyrite-bearing graphitic argillite unit within a sequence of intermediate to felsic volcaniclastics. Past operators established three mineralized zones along this horizon with combined reserves for two of the zones, of about 175,000 tons at 0.22 oz/ton Au. In the Preview Lake area , gold mineralization occurs in variably sheared gabbro/quartz diorite sills within a mixed sedimentary-felsic volcaniclastic sequence. Gold occurs with arsenopyrite, pyrite and minor chalcopyrite associated with quartz veins and stringers. A sulphidebearing graphitic argillite unit occurs in close proximity to the mineralized shears. Past operators delineated seven mineralized shear zones, two of which were drilltested. Average gold grades reported are in the 0.1 to 0.2 oz/ton range with erratic values up to 5.0 oz/ton.

Jan 1, 1986

By Gheorghe Vieru

Security and safety due to environmental impact as well as the radiological consequences during the uranium mining operations, tailings management, uranium processing, disposal of waste in conventional landfill sites are matters of great importance. The Uranium National Company (CNU) from Romania is responsible for all aspects belonging to the management of the entire Romanian uranium industry- the uranium ore extraction, transport and processing of uranium ore, concentrates processing, as well as disposal of sterile ore and waste. The paper will presents specific safety problems related to the identification and evaluation of potential environmental risks, as well as possible radiological consequences associated with the disposal of sterile and the uranium processing waste resulting from processing of the uranium ore. Computer codes will be used, such as IAEA INTERTRAN II and RADTRAN 5. It is also to be noted that this paper considers the main results of the scientific research carried out by the main author as CSI (Chief Scientific Investigator) for Romanian Research Contract on NORM concluded with IAEA Vienna.

Aug 1, 2010

By Amin Jafari

Macrosegregation has always been an important issue with the solidification processes, particularly in Direct-Chill Casting of Aluminum alloys, where uneven properties, surface and bulk defects and limitations in productivity can be arisen due to macrosegregation in the cast product. Following the global attempts to practically predict the macrosegregation, in the present work, a numerical model was developed based on an industrial scale DC casting process to simulate the solidification and macrosegregation in an Al-4.5%Cu billet. Interesting aspects of this investigation are concerned with an efficient numerical scheme to keep simplicity, consistency and desired physical resolution of the solidification phenomena together. In the mathematical model, coupled conservation equations of mass, momentum, energy and species were solved numerically using finite volume method. A different numerical scheme, called SIMTLE, was introduced to link the energy and species equations with the phase diagram of the alloy. Calculations were performed on an industrial case and obtained results were compared to available experimental data to assure the performance of the model. Different macrosegregation features were predicted and discussed on the solidifying Al-alloy billet.

Oct 1, 2011

THIS article describes the origin and details of a hydraulically operated switch to control the operation of an automatic underground pumping system. This system was installed in December, 1939, on the 2,350-foot level at No. 5 shaft of the Buffalo Ankerite mine. The pumping unit consists of an 8-stage centrifugal pump direct-connected to a 150 h .p., 2,200 volt motor. Pumping capacity is 200 gallons per minute under a 1,315-foot head and with a flooded suction. The control consists of a 200 amp., 2,200 volt oil-immersed starter with thermal overload protection, thermal protection on the pump, and a flow switch that is bypassed for 30 seconds after the pump starts. The 30-second time lag is operated by a relay mounted on the panel. There is a swing check valve in the discharge line of the pump which originally operated the flow switch by means of a connected outside lever which closed the switch as the check valve opened.

Jan 1, 1945

By G. J. Hawkes

"We all know that every man who works for us should have a thorough knowledge and understanding of his responsibilities. But how about ourselves? Du we have a thorough knowledge and understanding of our own responsibilities as Mill Superintendents?I once had an occasion to say to a Manager that I did not know something was my responsibility and he replied with suitable emphasis ""Everything inside those four walls is your responsibility"". That makes the extent of our responsibilities clear but does not give us a check list to keep an eye on as we do our job from day to day.What are our responsibilities? I suggest they are the following:1. Developing and maintaining efficient operating and maintenance crews.2. Milling the required tonnage.3. Recovering the economical maximum amount of gold.4. Keeping costs at the economical minimum.5. Seeing that the figures are reasonably accurate for tonnages, assays, production, losses, and costs.6. Preventing accidents.7. Preventing fires.8. Maintaining the equipment and building and keeping them clean and tidy.9. Enforcing company rules and regulations."

Jan 1, 1965

By A. E. Gillis

"Some or all of the following benefits can be expected following application of automatic control to a grinding circuit:1. Maintenance of Optimum Mill Load Level2. Improved Uniformity of Grind3. Increased Productivity4. Decreased Power Costs per Unit of Product5, Reduced Ball Wear per Unit of Product6. Reduced Labour Costs per Unit of Product7. Reduced Operator SupervisionTo establish an indication of the benefits that could be expected through automation of the grinding circuit at East Malartic Mines Ltd. it was agreed that the Department of Mines and Milltronics Limited should jointly conduct a survey of the existing grinding circuit and operation.Aside from establishing feasibility, an important purpose of this survey was to determine costs of a suggested control system that East Malartic Mines Ltd. management might be in a position to assess the economics of the proposal and justification of the investment.The survey involved the taking of sound recordings of rod and ball mills during manual operations, locating circuit bottlenecks, establishing time constants and determining the number and location of sensors for good automatic control."

Jan 1, 1966

By G. Chi, W. J. Davis, S. Watters, D. Hoy, S. Castonguay

"The Poplar Mountain gold occurrence in western New Brunswick is hosted in the Poplar Mountain volcanic complex (PMVC), which is located along the southern segment of the regional Woodstock fault zone. The PMVC consists of three principal units including, in ascending order, a porphyritic felsic volcanic unit, a volcaniclastic unit, and a mafic volcanic unit. U-Pb dating of zircon indicates that the age of the volcanic rocks is younger than 459 ± 3 Ma, and 40Ar/39Ar dating of mineralization-associated sericite indicates that the age of mineralization is 411 ± 3.7 Ma. Gold-mineralized zones occur in all the lithologic units but mainly in the porphyritic felsic volcanic unit. Gold zones are not controlled by individual faults but are characterized by high-density brittle fracturing, thin carbonate-quartz veining, and intensive ankerite-sericite alteration, superimposed on an earlier chlorite-calcite- quartz alteration. Gold is associated with arsenopyrite, which mostly occurs as disseminations in the host rocks, and to a lesser extent with quartz-carbonate-sericite veins and quartz-cemented breccias.Geochemical data indicate that mineralization-associated alteration is characterized by enrichment of K, Rb, Cs, Ca, Sr, Ba, As, Sb, W, C, and S. Fluid inclusion data indicate that the mineralizing fluids are composed of H2O, salts, and CO2 with variable amounts of N2 and CH4; salinities range from 2.3 to 10.6 eq. wt.% NaCl, but mainly from 2.3 to 5.6 eq. wt.% NaCl, and homogenization temperatures lie mainly between 220° and 270°C. Fluid pressures at the site of mineralization are estimated to have been 770 to 1200 bars, corresponding to a depth of 2.9 to 4.6 km at lithostatic pressure. The d18OSMOW and d13CPDB values of mineralization-related ankerite range from +14.5‰ to +16.5‰, and -6.8‰ to -8.3‰, respectively. The d18O values of the ore-forming fluids are estimated to be 6.4‰ to 8.3‰ at a temperature of 250°C. These carbon and oxygen isotope data fall in the field of magmatic fluids and in part the field of metamorphic fluids.Considering the geological setting of the region, abundant granitic intrusions, the similarity between the age of mineralization (411 ± 3.7 Ma) and the nearby Pokiok batholith (402-415 Ma), and the enrichment of granophile elements in mineralization-related alteration, the ore-forming fluids were probably derived from a granitic intrusion underneath the PMVC. These fluids were focused along structures related to the Woodstock fault. The Poplar Mountain gold occurrence might be compared to some granitic intrusion-related gold systems based on the geochemical data presented herein. L’indice aurifère de Poplar Mountain dans l’ouest du Nouveau Brunswick est contenu dans le complexe volcanique de Poplar Mountain (CVPM), lequel est situé le long du segment sud de la zone de faille régionale de Woodstock. Les trois unités principales du CVPM sont, de la base au sommet, une unité volcanique felsique porphyrique, une unité volcaniclastique et une unité volcanique mafique. La datation U-Pb de zircons indique que les roches volcaniques sont plus jeunes que 459 ± 3 Ma, et la datation par la méthode 40Ar/39Ar de séricite associée à la minéralisation assigne à la minéralisation un age de 411 ± 3.7 Ma. Bien que les zones minéralisées en or soient présentes dans toutes les unités lithologiques, on les retrouve surtout dans l’unité felsique porphyrique. Les zones aurifères ne sont pas contrôlées par des failles individuelles mais sont caractérisées par une grande densité de fractures cassantes, de minces veines de quartz-carbonate, et par une altération en ankérite-séricite intense qui se superpose à une altération antérieure en chlorite-calcite-quartz. L’or est associé à l’arsénopyrite, laquelle est principalement présente à l’état de disséminations dans la roche hôte, et à un moindre degré avec des veines de quartz-carbonate-séricite et des brèches à ciment de quartz.Les données de géochimie indiquent que l’alté"

Jan 1, 2008