Search Documents

By Tyler Roberts

New Afton mine is an 11,000 tonne per day block caving operation, located 8 km west of the city of Kamloops, British Columbia. Due to the nature of block caving and the weak rock mass at New Afton, the mine has faced and overcome many blasting challenges during its ramp-up to commercial production. As New Afton Mine continues to grow the demand for drill and blast precision has continued to grow as well; any misstep incurs delays in achieving full production capacity. The block cave mining method used at New Afton employs single-shot draw-bells, fired with very little void and blind undercutting, allowing little margin for error. New Afton has made continuous improvements to its blasting strategy by reacting quickly to real-time problems and employing sustainable, repeatable solutions to overcome its unique blasting requirements. Examples of these solutions include: increasing blast hole diameter, casing production drill holes, developing pre-loading procedures and developing strategies for remotely blasting under-broken remnants in both draw-bells and undercutting. Increasing the blast hole diameter has alleviated initial problems with hole plugging in the highly jointed rock mass at New Afton. This has reduced drill-cleaning time significantly and enabled New Afton to meet blasting targets. PVC hole casing was trialed when blasting in extremely fractured ground, where drill holes continually plugged. The casing allowed the drill holes to remain open long enough to load and blast. Calculations were carried out in order to achieve the same explosive energy in the cased holes as a typical blast. Results were generally positive, but more testing is required. Production flexibility and scheduling reliability have been maintained at New Afton by developing a pre-loading procedure for the production undercutting. In doing so, New Afton has been able to keep productivity high by having a flexible production schedule that is not reliant on a specific piece of equipment or production drive to remain productive; this flexibility is because the mucking of undercut material can occur at any stage of the drill/blast/muck cycle. New Afton has developed a strategy for blasting remnant under-break in its draw-bells and undercutting by remotely drilling holes near to the under-broken section and then loading the toes of these holes with emulsion, the remainder of the hole is then filled with grout. The holes are grouted in order to prevent damage to permanent pillars between draw-bells (where the majority of the recovery holes need to be located). Several critical areas were recovered using this technique with little to no damage to the remaining permanent pillars. Innovative blasting solutions have allowed New Afton to overcome obstacles in order to become a producing operation. Moving forward, New Afton looks to continue its trend of innovative drilling and blasting techniques when faced with out of the ordinary situations.

Aug 1, 2013

This paper details a brief history of the Australian gold industry from the 1980s gold boom to the present day, highlighting an industry characterised by innovation in plant design and junior companies prepared to "have a go", in contrast to the conservatism of many larger mining companies. Design flexibility, the innovation of new processes, the preparedness to exchange "process know how" and technology singularly differentiated the gold industry from other sectors during the 1980s to the present. The introduction of two stage crushing, semi autogenous (SAG) milling, and pebble crushing, mill innovations, carbon in pulp (CIP) and carbon in leach (CIL) and the North Kalgoorlie screen etc were all exciting changes in the industry.

Jan 1, 2011

By V. Polotski

Initiated and financed by the Canadian Space Agency, Micro-Rover Platform with Tooling Arm (MRPTA) project has targeted the development of a robotic system with remote control and autonomous navigation capabilities for testing a large variety of analogous planetary missions. Although developed for planetary exploration, the navigation system is highly suitable to such areas of application as construction and in mining. Autonomous navigation system is capable of moving the platform to predefined position(s)/orientation(s) while continuously mapping the terrain, assessing its traversability and choosing most appropriate path to follow. Designed according to the JAUS (Joint Architecture for Unmanned Systems) framework, the system consists of several interconnected components. Following components are of particular importance: Pose Estimator (PE), Terrain Evaluator (TE), Map Manager (MP), and Path Planner (PP). The PE uses a minimal sensor configuration consisting of an azimuth gyroscope, inclinometer and wheel odometry. The PE provides reliable pose estimates in spite of pronounced slippage by employing extensive use of fused data. The TE uses a nodding laser scanner which continuously sweeps the area in front of the platform and constructs a ?traversability grid? (TG) of the surrounding area. Multiple TGs are constantly constructed along the platform motion path are combined into a terrain map maintained by the MP. The PP uses this map to compute a motion path Obtained path is executed by the motion controller and remains current until it is contradicted by the most recent map ? at which point it is re-planned. This paper addresses integration issues, lessons learned and also outlines the possible applications for construction and mining.

Aug 1, 2013

By E. Trickey

In the mining industry there exists a constant drive for increased safety and productivity and decreased operating costs. This acts as a driver for implementing advanced technology. As more and more mining operations turn to new technologies, an observed bottle-neck for technology advancement has been the limitation of machine vision solutions available. LiDAR has been seen as a possible solution to the machine vision problem. In the past, a few studies on machine vision solutions have been undertaken by various groups involving scanning laser range-finders and millimetre-wave radar. These studies have done little more than highlight the limitations of both technologies in the mining environment. Little work has been done, however, exploring the applicability of LiDAR imaging technology for mining applications. Neptec Technologies Corp. has developed an obscurant-penetrating LiDAR (OPAL) sensor technology which overcomes the limitations faced by traditional LiDAR sensors when operating in a dusty environment, as well as advanced 3D real-time intelligence (3DRi) data processing algorithms that enable the real-time exploitation of 3D imaging data with sensors mounted on moving vehicles. Working with Teck Resources Ltd. and Barrick Gold Corporation, Neptec is adapting the OPAL sensors and 3DRi technology to mining applications. This paper highlights a number of real-time OPAL/3DRi based mining applications demonstrating how this technology overcomes the limitations of traditional LiDAR to provide a real-time machine vision solution that supports mine machine autonomy.

Aug 1, 2013

By M. C. Bétournay, J. E. Udd

"The legacy of abandoned mines in Canada creates issues that impact on both the health and safety of Canadians and the environment. Solutions to the problems of abandoned minesites require a detailed understanding of site conditions, the engineering solutions which may be relevant, and planning for effective use of the land. In this paper, the authors outline the basic thrusts that have been developed at CANMET to address this problem. These include: multiprovincial agreements to develop a national database; methods of site rendering; a ten-year research program to develop engineering approaches; the review of a large number of case studies; and outlining the associated risks. Examples of the applications of this research are provided in the areas of: municipal, provincial, and federal co-operative projects; site-specific applications; and international linkages."

Jan 1, 1997

By D. F. Scott

"DEFINITION OF THE REGION AND ITS BOUNDARIESTHE REGION of Western Canada covered by this re-port lies between the Precambrian rocks of the Canadian Shield and the structurally deformed rocks of the eastern Cordillera, extending northward from the international border to the 60th parallel. It is some 487,000 square miles in area, with a total sedimentary fill of about 535,000 cubic miles0>. It includes parts of the prairie provinces of Manitoba, Saskatchewan and Alberta and the northeast corner of British Columbia and forms part of the geological region known as the Interior Platform, commonly referred to as the Western Canada Sedimentary Basin. The bedrock comprises carbonates and evaporites of Paleozoic age that lie on Precambrian crystalline rocks and are over-lain by a relatively thick blanket of Mesozoic and Tertiary elastic rocks. The nearly flat-lying bedrock, covered by a thick mantle of glacial drift, forms the Interior Plains physiographic province."

Jan 1, 1970

By Mario A. Morin

Mine design, planning and scheduling is a very complex, iterative process comprising several interrelated and interdependent activities. Understanding how this process works, identifying the critical pieces of information and the decisions to be made is key to initiating business process improvements (BPI) or business process reengineering (BPR) activities. Fundamental to most BPI and BPR work is some form of systems analysis. Structured Analysis is a powerful systems analysis technique that is well suited for modeling and analyzing complex process activities. Through a series of diagrams, this paper presents a vertical slice through the analysis work performed for formally describing the underground hardrock mine design and planning process. These diagrams illustrate how simple graphic constructs can be used to decompose the most complex situations into easily understandable diagrams that facilitate understanding, communication, improvement and reengineering.

May 1, 2002

By Louis Frost

The coal-mining industry of Nova Scotia, particularly of the island of Cape Breton, today faced as no other industry with economic problems calling for progressive engineering with production on an economic basis, must soon enter upon a phase of reorganization wherein all factors conducive to the cost of producing coal relative to the prolongation of the life of the collieries with the ultimate winning of the maximum submarine area must be closely reviewed. Bearing this in mind and applying the process of elimination to coal-mining costs generally, we are left with only three channels through which we may approach the problem of cost reduction in producing coal: (a) intensive mechanization (b) reduction in the cost of labour (c) reduction in the cost of materials. Assuming that mechanization has reached an economic stage and that labour costs have reached an economic limit, we must turn our attention to the general material costs, which may be classified as 'live' and 'dead' costs. The former take in all things which can be accredited with a fractional depreciation and written off the balance sheet over a period of years. On the other hand, the ?dead'costs-of which the cost of supporting the underground workings form part must be completely written off: for these, no return may be expected, other than the economic return in the reduction of the cost per ton of coal produced.

Jan 1, 1928

By Jodi Wilding, Barry Lurnsden

The implementation of new technology to mineral separation operations requires rigorous testing to confirm the technology&apos;s technical and economic benefit. The Jaguar Mine owned by Jabiru Metals is located in Western Australia and sequentially separates a copper concentrate and then a zinc concentrate. Fine grinding (80% of zinc in tail is <25µm) is required to achieve efficient mineral separation. All mineral losses are therefore fine mineral losses, and so improvements in metal recovery must focus on this fine mineral. Magnetic aggregation technology has been shown to increase the recovery of fine paramagnetic minerals so it was an appropriate technology to evaluate at Jaguar. Testwork commenced in the copper circuit and it was found that there was a substantial reduction in copper in copper tail and an increase in zinc recovery to the zinc concentrate. The increase in zinc recovery in the latter zinc circuit was an interesting result and initiated the second stage of testwork that was to install and test a second magnetic conditioning unit in the zinc círcuit. This showed a further increase in zinc recovery. Magnetic conditioning technology has now been fully evaluated in the plant and is now part of the Jaguar flowsheet.

Jan 1, 2011

By J. Lapointe, S. Leger, D. Proulx

"Une méthode non-électrolytique est utilisée pour plaquer au cuivre la fibre d&apos;amiante chrysotite. En variant les paramètres de placage du bain, on détermine les conditions optimales du taux de deposition du cuivre . Une analyse par diffraction aux rayons-X permet une comp araison relative des résultats de placage et de précipitation d&apos;oxyde cuivreux dans Ie bain. Le traitement de placage a pour but d&apos;assurer une adhésion suffisante de la fibre dans une matrice métallique Iors de la fabrication éventuelle de materiaux composites.IntroductionCette communication se veut un compte-rendu de nos travaux sur Ie placage au cuivre de la fibre d&apos;amiante chrysotile, en vue de I&apos;incorporer éventuellernent dans une matrice métallique. La fibre d&apos;amiante est constituée de fib rilles élementaires d&apos;un diamètre d&apos;environ 0.02 um qui ont une résistance en tension de I&apos;ordre de celie de la fibre de verre ou de carbone(1). Pour être efficace, la fibre de renf&apos;ort d&apos;un matériau composite doit d&apos;une part, avo ir des propriétés mécaniques intrinsèques élevées, et d&apos;autre part, adhérer solidement â la matrice pour que Ie transfert de charge s&apos;effectue sans qu&apos;il y ait décohésion entre les composantes du matériau.La fibre d&apos;amiante étant naturellement soyeuse, il faut la traiter superficiellement pour que l&apos;adhésion avec la matrice soit suffisante. Ainsi, on recouvre la fibre de phénol-formaldéhyde(2) ou de silane(3) lorsqu&apos;elle est employée avec une matrice polymere. Dans Ie cas d&apos;une matrice métallique, ces dépôts organiques ne peuvent resister aux températures de mise en oeuvre, d&apos;où l&apos;intérêt de plaquer les fibres par un dépôt métallique.Dans cette étude, nous rapportons les résultats relatifs à la methode utilisée pour plaquer au cuivre la fibre d&apos;amiante chrysotile. Une analyse par diffraction aux rayons-X permet de comparer les différentes conditions de placage non-électrolytique."

Jan 1, 1985

By R. A. Hemstock

"Simple classification systems are now being used which will describe adequately the surface vegetation, the topography and the peat for any muskeg condition. Good progress is being made in determining some of the mechanical properties of muskeg and it is apparent that the science of soil mechanics will apply largely to these studies. Correlation is also indicated between shear strength as determined by the shear vane tester and vehicle performance. Several tracked vehicles are now available which perform well in muskeg and advances in this field have come rapidly in the past few years. Testing is under way on the largest of all muskeg vehicles -the thirty-five ton Musk Ox. This vehicle will fill the last gap for the oil industry and will make possible the movement of large drilling rigs at any season of the year."

Jan 1, 1960

By R. J. Young, S. J. Tennant, A. D. Drummond

"Gibraltar Mines is located on the western slope of Granite Mountain, 230 air miles north of Vancouver, B.C. and 38 miles north of Williams Lake, B.C. There are four mineable zones within the copper-molybdenite deposit: Gibraltar East, Gibraltar West, Pollyanna and Granite Lake. Open-pit reserves are 358 million tons which average 0.37% Cu and 0.016% MoS2 at a 0.25% Cu cut-off. The Granite Mountain pluton is one of the several Jurassic-Cretaceous intrusions which outcrop along the east side of the Fraser River fault system between Williams Lake and Prince George, B.C. The original Granite Mountain quartz diorite has been metamorphosed by a cataclastic deformation which foliated the rock on a regional scale. Attendant to the development of the foliation, the rock was saussuritized such that the present mineralogy is compatible with that of the greenschist facies. The presence of garnet-bearing assemblages is explained by a restricted increase in water pressure. Pre-mineral intrusive phases within the saussuritized quartz diorite are: (1) leucocratic quartz diorite, (2) aplite and (3) quartz-feldspar porphyry. A late chloritized hornblende dacite dyke is post-mineral. Quartz-feldspar porphyry and leucocratic quartz diorite are locally present on the inner sides of the Gibraltar East, Pollyanna and Granite Lake pits. Their presence suggests a core around which occurs an elliptically shaped sulphide-bearing stockwork. The stockwork, which comprises four ages of vein development, is imposed on and partly controlled by the regional foliation of the samssuritized quartz diorite."

Jan 1, 1973

By J. D. R. Neilsen

The objective of the research conducted and presented herein was to determine the effect of pre-established free gas saturation on the sweep efficiency of an isolated inverted five-spot well pattern. The investigation concluded that the ultimate recovery of an isolated inverted five-spot may be slightly increased by establishing a free gas saturation prior to water flooding; however, of more significance is the extreme deviation of the pattern's performance after water break-through from that commonly obtained from developed well patterns. The rapid "water-out" characteristic common to both linear floods and floods conducted in developed well patterns was not evidenced in the isolated inverted five-spot. Instead, the wells continued to produce oil long after breakthrough until ultimate areal sweep efficiencies of four, five, and six hundred percent were obtained prior to the water-oil ratio becoming excessive.

Jan 1, 1962

By J. C. Loretto, H. A. Simons

The paper discusses how, in the routine testing of ores, insufficient communication between the laboratory and the design personnel can lead to misunderstanding or misinterpretation of test results and consequent design errors. A number of examples are given together with suggested modified interpretations and the resulting dollar savings indicated by these new interpretations.

Jan 1, 1972

By The Hollinger Mill Staff

MR. E. L. Longmore (l), in presenting this paper at the Annual General Meeting, suggested that it was neither desirable nor necessary to read any but the briefest portion of the paper. He wished to emphasize that the scale of the milling operations at the Hollinger not only provided several units in continuous operation to ensure that the test work was being carried on under normal conditions, but also provided a large and competent staff to supervise such an extensive experiment and to criticize intelligently the recorded results. He wished to acknowledge the enthusiastic co-operation of the group of assistants whose excellent work was responsible for the confidence with which the conclusions could be presented. The following data were given as a supplement to the published paper. Following conclusion of the test work described in the paper, the size of the balls fed to the mill was changed from 3-in. diameter to 2Yz-in. Within a short time, a gradual rise in the tonnage rate took place and, as no other condition had been changed, the increased tonnage was credited to the changed character of the ball load. At present, the average daily tonnage for the mill with low discharge is 1,507 tons, an increase of 77 tons over the 1,430 tons ground when feeding a 3-in. ball. A similar increase in tonnage should be credited to the high-discharge test, if the 2;Y2-in. ball had been used at that time. This would raise the 1,117 tons ground at that time to a new figure of 1,177 tons. From a study made to determine those factors influencing the rate of pulp flow through the low-discharge mill, it became evident that the ball screen used on the high-discharge mill must have been restricting the flow through the mill, although this was not recognized at the time. Accord-ingly, it was decided to repeat the high-discharge run. Additional length was added to the 21-in. ring grizzly originally used, and the length of the reverse spiral was increased. The end of the grizzly was left open so that, if necessary, excess pulp might flow out. A coarse mesh 3 ft. by 3 ft. flat screen was provided to catch stray balls.

Jan 1, 1937

This paper deals mainly with the modernization in the coal loading system at the loading piers of the Dominion Coal Company, Ltd., Sydney, Nova Scotia. The history of the operation is briefly outlined, and the construction of the Company&apos;s new pier is described in considerable de-tail. Particular attention is paid to the bins and conveyors, and to the loading tower. The paper concludes with a description of the S.S. Cape Breton Miner, built specifically for the coal trade, and the unloading facilities at Lakeview, Ontario. Coal Shipping at Sydney C OAL from the mines operated in Cape Breton by the Dominion Coal Company, Limited, has been shipped from the International Piers, situated on the east side of Sydney Harbour, for over sixty years. There were three piers, of which two were active-ly used in the shipping of coal until 1964. Nos. 2 and 3 were high piers about 600 feet long, of wooden construction throughout. They were founded on&apos; rock-filled cribs and creosoted piles driven into the harbour bottom, and each had two decks which carried standard-gauge railway tracks.

Jan 1, 1965

By Wm. F. Wuest

INTRODUCTION THE Western Canada sedimentary basin has one feature in common with the Precambrian Shield area: it also was a great chemical laboratory. The mining industry of Canada exploits the end products of chemical experiments that occurred on the Shield during periods of repeated disturbances in Precambrian times. The petroleum industry on the other band exploits what also appears to be the final results of chemical experiments that took place throughout all of post-Precambrian up to Tertiary times. Since the subject of this paper is a factual study of Alberta well waters, no attempt is made to answer significant questions pertaining to the probable role waters play in the generation of oil, or to the significance of the effects of structure and depth on waters. Data from several hundred well-water analyses were compiled by the writer in a series of charts and diagrams, of which those included in this paper are representative. Early studies indicated the possibility that outstanding anomalies in general concentration of waters and in greatly increased concentration of elements such as calcium, magnesium, bromine, and iodine for example, might be expected from wells that produced oil or were in the immediate vicinity of producers. The water analyses from wells which? were drilled at a later date did not confirm this possibility, and it is suggested that, aside from their initial value to the petroleum engineer or to. those interested in the commercial possibilities of brines, no definite significance as an aid in oil discovery can be attributed to water analyses.

Jan 1, 1951

By Peter Rubie

For many years, optimising the relining of hard rock grinding mills has been complicated by: ?? the large number of variables; ?? the low frequency of relines (slow feedback loop); ?? the potential economic risk associated with some changes. A technology that has its roots in the automotive manufacturing industry is being utilised to construct a statistically accurate, configurable, and dynamic simulation of the mill relining process. The effects of various mechanisation and process changes can be rapidly modelled and compared. This technology will provide mill maintenance managers and contract relining companies with the opportunity to benchmark current performance against world?s best practice. It will also provide an opportunity for concentrator plant designers and mill manufacturers to plan for maximum plant efficiency, by designing an infrastructure and equipment combination that maximises annual plant availability. This simulation tool and its associated data set, has been developed using recent grinding mill performance data from mills of varying dimensions, liner configurations, mill relining equipment, operator and tool variables. The simulation will provide an output that the various stakeholders can utilise to make optimal decisions within the given financial, physical and technological constraints of the individual concentrator plant.

Jan 1, 2012

By A. M. Simons

Cyanide destruction by Caro’s acid is one process commonly employed by gold operations to meet regulatory requirements and/or the International Cyanide Management Code compliance for weak acid dissociable (WAD) cyanide in cyanidation tails or waste water from such operations. Typically smallscale bench tests to evaluate and assess the suitability of the Caro’s acid destruction process are conducted. Additionally, the experimental procedure used during these preliminary investigations may also differ from that implemented at the full-scale. This paper presents the results from a fundamental investigation of the Caro’s acid process to establish a more detailed understanding of the impact that the experimental procedure has on the destruction of cyanide. In particular, it was found that the control of pH was important to avoid copper(I) cyanide precipitation at low pH and maximise WAD cyanide destruction. Residual peroxide in the preparation of Caro’s acid has the potential for subsequent cyanide destruction and could be exploited.

Jan 1, 2014

By Mark Weidenbach

OZ Minerals owns and operates the Prominent Hill copper-gold concentrator in South Australia, built in 2008 and commissioned in early 2009. The concentrator operates via semi autogenous grinding in a thirty four foot ThyssenKrupp Polysius mill followed by a twenty four foot Polysius ball mill in closed circuit with hydro cyclones, designed for an ore throughput of eight million tonnes per annum. The main aspects of designing the circuit are discussed along with the issues faced in the early stages of operation. A review of the optimization strategy applied to the milling circuit such as cyclone optimization, advanced process control strategy implementation and reline management to improve availability is then discussed highlighting areas of significant process improvement that have seen the plant exceed nameplate throughputs above nine million tonnes per annum.

Jan 1, 2012