Search Documents

By P. Momni, D. Ersenkal

Equator Principles (EPs) are a set of guidelines developed and adopted by a series of financial institutions for assessing and managing social and environmental issues in project financing. Established in 2003, EPs are now adopted by some 68 financial institutions from 27 countries. As more and more financial institutions join this global initiative, it is important for project owners to have a logical framework embedded into the project lifecycle to reduce the risk of non-compliance which could result in costly delays. This paper outlines a proactive approach for project developers in order to integrate environmental and social aspects into entire project lifecycle.

Jan 1, 2010

By M. P. Du Plessis

"The paper discusses coal research in relation to the special needs of Western Canada, with its large resources of lignite and subbituminous coals. Research programs are presented under the following headings: Coal Liquefaction, Pyrolysis, Fluidized-Bed Technology, Underground Coal Gasification and Supporting Investigations. Typical processes are presented and their relevance to Canadian coals is described. The longterm plan of the Alberta Research Council for coal research and the steps taken for its implementation are discussed. Finally, some innovative concepts arising from basic research in coal chemistry are discussed.Canada's Coal ResourcesCanada is richly endowed with coal reserves. With estimated ultimate reserves of 600 billion tons in O.76-m (2.5-ft) thick seams under less than 762 m (2500 ft) of overburden, Canada rank s fourth after the USSR, the USA and Chinatu (see Table I) . Canada's reserves are incompletely explored and estimates are constantly being upgraded. Preliminary information from deeper test-hole logs suggest that similar , if not larger, tonnages occur at depths greater than 762 m (2500 ft).The types of Canadian coals and their regional Distribution(2) is shown in Figure 2. Alberta's subbituminous Plains coal represents about 70% of estimated national reserves. A large portion of the coal can be mined at relatively low cost by surface mining techniques, and it is currently being used exclusively for power generation in conventional thermal plants. This coal, however , also represents a large potential .source of liquid fuels which could equal or exceed that of oilsands and heavy oil. Table 3 compares Federal Government estimates for resources and reserves of fossil fuels in Canada and their recoverable oil content or equivalent.A conservation estimate of only the reserves of thermal coal represents an oil equivalent of 27.6 billion barrels , which equals the recoverable reserves of oil-sand bitumen and heavy oil. A more realistic estimate is probably several times this amount. Although coal can be converted to many other end products, such as fuel gas and synthesis gas for hydrogen and ammonia production, liquid fuels remain the most desirable product mainly because they can be transported more cheaply over long distances and their high energy density makes them uniquely suitable as fuels for transport and agriculture."

Jan 1, 1981

By C. Díaz, A. D. Dalvi, C. E. O'Neill

"Roast-reduction smelting (RRS) of nickel concentrate, combined with flash smelting of copper concentrate, was one of the process options that Inco considered as a means of meeting its 1994 sulphur dioxide abatement target at its Copper Cliff operations. RRS involves deep roasting the nickel concentrate in fluid bed roasters. The roaster off-gas is treated in a sulphuric acid plant, and the low sulphur calcine is reduction smelted with coke in an electric furnace to yield a sulphur-deficient matte. The latter material is converted to Bessemer matte in Peirce-Smith converters, with minimal evolution of sulphur dioxide, and the converter slag is reverted to the electric furnace. Excellent nickel and cobalt recoveries (Ire obtained. This paper discusses the development of RRS, including extensive commercial scale testing at Inco's Thompson Smelter, and its key operating parameters. IntroductionReduction of sulphur dioxide emissions has been a long-standing endeavour at Inco. At the company's Ontario Division, as shown in Figure 1, sulphur dioxide emissions were reduced from about 2 million to 685 000 tonnes per year over the period 1970-1985. Most of this impressive improvement was the result of a sustained research effort which led to increased rejection of pyrrhotite from the ore during milling while maintaining an acceptable nickel recovery. Between 1970 and 1985, the combined grade of the separate nickel and copper concentrates feeding the Copper Cliff Smelter increased from about 10070 to about 'lIJ0J0 Cu +Ni and the combined S/(CU +Ni) ratio decreased from about 2.8 to 1.65."

Jan 1, 1994

By P. B. Marchant

"Considerable gold and silver values are lost to flotation tailing from both the South ern Tail orebody and the Main Zone orebody,The underlying mineralogical assemblage of the two ore types is quite different. This paper describes the research strategy employed to determine an economical method to scavenge gold and silver from flotation tailing.Much of the unrecovered gold in the Southern Tail ore is associated with arsenopyrite while silver losses are probably as unliberated tetrahedrite and minor silver-bearing sulphosalts. Processing alternatives tested include bulk sulphide recovery by flotation and gravity, selective pyrite-arsenopyrite separation, cyanidation, and oxidation pretreatments such as pressure leaching and bioleaching to enhance cyanidation response. Gold losses in the Main Zone ore are more closely associated with silver-bearing minerals, pyrite, and siliceous gangue and consequently respond more readily to conventional tank cyanidation. The 5 300 tid carbon-in-leach circuit to treat Main Zone flotation tailing is described in detail.IntroductionEquity Silver Mines Limited's open-pit silver mine, a 70% owned subsidiary of Placer Development Limited, is located 37 km southeast of Houston in north central British Columbia. The deposit consists of two major ore zones, Main Zone and Southern Tail (Fig. I). These zones are within a sequence of Cretaceous volcanic and sedimentary rocks striking 015 degree s and dipping 45 degrees west. Feasibility ore reserves were 28 million tonnes grading 106 g A g/t, 0.96 g Au !t and 0.38% Cu a strip ratio of 2.2 to I. A detailed mineralogical description has been presented and a comparison of the two ore zones is shown in Table I."

Jan 1, 1986

By James Stenhouse

Abstract The aqueous oxidation of pyrite in caustic solutions under oxygen pressure was investigated by measuring that effect of reaction variable on oxygen consumption by the reactions. From the results of this investigation, a model for the process has been proposed. In this model, sulphur diffuses as a positive ion through an oxide layer which forms on the sulphide particles and is then oxidized to sulphate ion. Iron is oxidized by substitutional diffusion of oxygen atoms into the oxide layer. The effect of most reaction variables on the rate of oxygen consumption can be explained with this model. Introduction Recent investigations (1,2,3) have shown that certain sulphide ores can be readily leached by agitating the ore in the form of a pulp under pressure in the presence of oxygen. Since very little was known of the mechanism of this oxidation, a programme of investigation was inaugurated in 1949 in the laboratories of the Department of Mining and Metallurgy of the University of British Columbia. Financial support for the investigation was received from the National Research Council in the form of student grants and bursaries, from the Canadian Liquid Air Company, Limited, and from the Consolidated Mining and Smelting Company of Canada, Limited. The first objective was to devise a technique to study the primary oxidation reactions in aqueous solutions and to apply the technique to a detailed study of the oxidation of pyrite in caustic solutions.

Jan 1, 1952

By C. I. Walker

Field tests at a number of large mineral processing operations have been undertaken to better understand the wear life impact of different aspects of pump design, materials of construction and maintenance procedures. Data are presented for wear rates, and typical result variability is explored. To improve the availability of pumping equipment in a milling circuit it is not only important to improve the wear life, but also reduce the variability in the wear life of components so that the incidence of premature failure is lessened. Localised gouging wear due to flow separation and turbulent eddy formation is often the point at which part-holing occurs. A number of improvements to the design of pump impeller and throatbush (suction side liners) to reduce the localised gouging wear are outlined. Also, results are presented on the use of composite materials (mix of metal, rubber and ceramic) for throatbush materials to protect specific areas against wear.

Jan 1, 2012

By J. A. Eisele, D. L. Pool

"The Bureau of Mines has developed a particle agglomeration technique to improve the flow of leaching solution through heaps of low-grade gold-silver ores which contain clays. Benchscale experiments and industrial practice have shown that the percolation rate of cyanide leaching solution is greatly enhanced by mixing the ore with Portland cement as a binder, moistening the mixture, mechanically tumbling to form agglomerates, and aging before heap building and leaching. A slight modification ofthe technique allows its application to precious-metal-bearing tailings, which cannot normally be treated by heap leaching because they are too fine. IntroductionMany low-grade gold and silver deposits and tailing materials from former mining operations in the western United States are potential sources for precious metals. These sources are too low grade or too small to support the capital cost of a conventional cyanidation plant but have stimulated the development of lowcost procedures, such as extraction of the precious metals by heap leaching with cyanide. The Bureau of Mines has investigated methods to improve the recovery ofgold and silver by heap leaching these low-grade materials.For heap leaching to be successful, the crushed and stacked ore must have good permeability so that uniform distribution of the cyanide leaching solution through the heaps can be achieved. Some of the most difficult gold and silver ores to treat by heap leaching are those containing excessive amounts of clays, or fines generated during crushing. Excessive amounts of slimes, generally minus 50-micrometre or 270-mesh Tyler sieve size particles, in the heap feed will slow the percolation of the leaching solution, cause channelling, or produce dormant or unleached areas within the heap, resulting in long leaching periods and low extractions. In extreme cases, the clays or slimes can seal the heap and cause the leaching solution to run off the sides of the heap rather than through it."

Jan 1, 1987

By Henri-Loui Jacob, Suzie Nantel

"Depuis la fin des annees 1800, la province de Grenville represente pour Ie Quebec une source importante et diversifiée de minéraux industriels. Le Ministère de l'Énergie et des Ressources du Québec, dans Ie cadre de I'entente auxiliaire Canada-Québec, et les compagnies minieres y ant multiplié, surtout depuis 1983, leurs travaux d 'exploration, de cartographie, et d'évaluation pour les minéraux industriels. Ces travaux ant conduit ala découverte et ala mise en valeur de gisements de granite architectural, de graphite, de dolomite et ant aussi permis de repertorier des gîtes et des indices prometteurs de wollastonite, de silice, de calcite. de dolomite, de silicates d'alumine et de terres rares. Les gisements récemment découverts sont actuellement exploités au sur Ie point de l'être et les gîtes et les indices les plus prometteurs ant été jalonnés.ABSTRACTSince the late 18oos, the Grenville Province in Québec has been an important and diversified source of industrial minerals. The Ministere de l'Énergie et des Ressources du Québec, under the Canada-Quebec Mineral Development Agreement, and the private sector have put an emphasis on exploration, mapping and evaluation programs in the Grenville Province for minerals, particularly since 1983. These programs have led to the discovery and the development of deposits such as architectural granite, graphite and dolomite, and have also led to inventories of occurrences and prospects of wollastonite, silica, calcite, dolomite, alumina silicates and rare earths. The deposits discovered lately are presently being quarried or will be in the near future. The most promising occurrences and prospects have been claimed."

Jan 1, 1990

By A. M. Nordale

Let us first trace a line, mentally, across Alaska and Yukon, starting at a point in the west slightly south of the delta of the Yukon river and from there continuing eastward, loosely following the 63rd parallel of latitude until we have passed beyond the eastern border of Yukon. We will make two pronounced digressions southward to include the greater parts of the Iditarod and Tanana River valleys. That visualized line roughly defines the southern boundary of permafrost. North of it lies a vast region, fully three-fourths of the area of the two territories, which includes Seward peninsula, the great Yukon River basin, and the tractless wastes of the Arctic. During some frigorific cycle in the distant geological past, the ground there was frozen to a depth of many hundreds of feet. How deep the frost actually penetrated is not known, but it has been found to exceed three hundred feet in many places. Nature afterwards provided a perfect insulating cover in the form of heavy moss and dense grass, which has protected the ground from the heat of the sun's rays during the intervening ages. This frozen condition has always been accepted as something indigenous to the North and little thought was given to -it until recently, when the United States Government and, I believe, the Canadian Government, began extensive studies of it, particularly in respect to its effect and bearing on the development of the great oilfields of the Arctic. Within this large region and but a short distance south of the Arctic circle are the three principal producing placer gold fields in the sub-arctic, whose hubs centre at Nome and Fairbanks in Alaska and at Dawson in Yukon Territory. The geological structure and history of the gold-bearing deposits of Dawson and Fairbanks are very similar and probably closely related. They are typical placer deposits produced by stream action during periods of erosion and inundation and subsequently covered with a thick layer of fine, powdery silt mixed with decayed vegetation which, locally, is termed 'muck'. The depth of muck varies from less than 10 to more than 250 feet, with the greater depth near the lateral edges of the valleys. The gravel underlying it is medium in size, well rounded, and composed mostly of quartz and schist. The proportion of sand or fines is approximately 40 per cent. No large boulders and little clay are found, for those districts, as well as that of Nome, have not been subjected to glaciation. The most common bed-rock found is either decomposed or hard schist, but infrequently it is slate, quartz, diorite, or a porphyry. The vertical concentration of the gold is invariably on bed-rock and in the lower few feet of gravel which overlie it. The horizontal concentration or paystreak is roughly parallel to the trend of the valley but does not ordinarily coincide with the course of the present stream. The width of the paystreak usually expands from a few feet at the head of a creek to several hundred feet near its mouth.

Jan 1, 1947

By P. Favreau

"This paper describes the progress accomplished at the Noranda Technology Centre in the field of three-dimensional computer-aided underground blast design. Traditional methods of laying out underground blasts are reviewed, and the new computer-aided approach is described. Time savings achieved through the use of BLASTCAD can be advantageously used to better engineer blasts, using models and blast vibration analysis. Future work involving the attachment of blast models directly to the system is also addressed.IntroductionThe Noranda Technology Centre's (NTC) Environment and Mining Laboratory, in cooperation with the mining operations of the Noranda Group, is committed to the development and implementation of new technologies in the field of mineral extraction . Within the frame of its research program, the Blasting Technology Program is developing computer "" tools"" designed to assist the blasting engineer or technician. These computer "" tools"" are regrouped under a global software system called BLASTCAD.The BLASTCAD project started in 1990 at NTC. At that time computer programs designed to calculate and model various blasting parameters had been accumulated. These programs cam e from different sources and were mutually incompatible. Furthermore, they were developed as research programs with tittle effort spent on user interface. These programs are very useful, but are highly specialized, need large input files and can be quite tedious to use as ""standalone"" packages .Therefore, the situation being faced was one where all these programs were available at the Noranda Technology Centre, but not a t the operations. The two following options were then considered: 1. continue to run all the models and programs at the Noranda Technology Centre, and present results through reports to the mines, or2. regroup all the different programs under a single one that would make them share the same data base and be transported to the user. This second option is the one that was adopted; the result is BLASTCAD."

Jan 1, 1993

By T. Crivits, I. Bellemans, K. Verbeken

In the metallurgical industry, furnace cooling is often employed to enhance furnace lifetime. Hence, the pyrometallurgical phase comes in close contact with a non-air coolant. The proximity of the pyrometallurgical phases to the coolants may lead to dangerous situations. In case of a breach of the cooling circuit, the contact between a hot and a cold liquid may cause a vapour explosion. The outcome of this vapour explosion includes a pressure wave which could result in damage to the furnace, bodily injuries or even casualties. To prevent such dramatic events, the origin of vapour explosions is currently being studied in more detail. For this purpose, OpenFOAM was used to perform Computational Fluid Dynamics (CFD) simulations. In a first step, simulations were run to get a better idea of the influence of the compressibility on the simulations. The obtained results help in getting a better insight on the need of computational power, and possible numerical errors using compressible or incompressible solvers in future simulations. In a second step, systems without vapour explosions were simulated and compared to experimental results with mercury and aluminum. INTRODUCTION Humanity started using metals for tools around the Chalcolitic (~7400 cal BC), when copper was melted in small furnaces (Radivojevic, Rehren, Farid, Pernicka, & Camurcouglu, 2017). Nowadays, metallurgy has grown into a major industry and it has become impossible to imagine society without metals. In the pyrometallurgical industry, coolants (low temperature liquids, for example water) and pyrometallurgical phases (high temperature liquids, such as slags, mattes and alloys) are typically present in close proximity of each other. The interaction between these two phases can have catastrophic consequences (Tveit et al., 2008; Ferguson & Zsamboky, 2017). A vapour explosion may occur as the consequence of the rapid evaporation and expansion of the coolant. Whereas the volume of a gas increases linearly with the temperature (approximately a factor four by heating from 100°C to 1300°C), a simple calculation of the ratio of the two specific volumes shows that evaporation causes the volume of water to increase by a factor of 1700 at 100°C and ambient pressure (Table 1 and equation (1)), a number that was also found in literature (George, Nexhip, George-Kennedy, Foster, & Walton, 2006). The volume change occurs so fast that it resembles an explosion, hence the name vapour explosion. Such an explosion at industrial scale can cause economical losses, bodily injuries or even fatalities.

Jan 1, 2019

By B. J. Cunliffe

"Filter cloth in the mining industry is an ambiguous title asthis suggests filter cloth use from underground ventilation to the refining processes. The time allowed for this paper would be better served in con-centrating on vacuum filters common to all mine mills and to offer some simple guide lines to the mill metallurgists in the choice of filter cloth for this type of filter.The requirement of the filter cloth is to separate solids from liquids under a vacuum head by forming a permeable layer of solids or cake, through which liquids can flow until the panel or disc sector leave the slurry tank and to continue to pass residual moisture from the cake formed during the cake drying cycle, and to discharge the cake on air-blow so that the cycle can be repeated.Whilst the mill metallurgist should not be expected to under¬stand all aspects of filter cloth manufacturer, it is however, advantageous for him to understand a little of the textile language associated with filter cloth for his own protection against ""trial-and-error"" methods, which are both time consuming and costly.If improvements are to be made over existing filter cloth in use an examination of the limiting factors of the cloth used should be made and the major causes for removal determined, e.g. cloth blinding, high moisture in cake, poor cake discharge on air blow, mechanical damage to cloth.As each of the limiting factors mentioned has a bearing on the choice of fibre used, the yarn type and weave of a suitable cloth, an under-standing of these points will assist the mill metallurgist in avoiding repetitive trials offering little degree of success."

Jan 1, 1971

By Pierre Beaudoin, Michel Bourassa, Robert Lanthier, Samir Chéfaï

"Mine Doyon, in collaboration with CRM's Process Control Division, improved the control strategy at the SAG mill I Ball mill grinding circuit. The project aimed at increasing operation stability and throughput. First, a needs analysis was achieved in order to define the control philosophy and to upgrade the process control equipments and instrumentation. The stabilizing control strategy has been developed and implemented successfully using single loop PID controllers. The monitoring feature as well as the rule based supervisory control strategy were implemented on 486PCs running Process Vision and COMDALE/C softwares. Main features of the control strategy are described in this paper while results are presented and discussed.RésuméLa Mine Doyon, en collaboration avec le service de contrôle des procédés du CRM, a optimisé la stratégie de contrôle au circuit de broyage. Les objectifs du projet étaient !'amélioration de la stabilité de !'ensemble de !'opération et la maximisation du tonnage usiné. Une analyse de besoins a été réalisée pour concevoir la philosophie de contrôle et déterminer les ajouts a apporter a I 'instrumentation et au systeme de contrôle. Une stratégie de contrôle à deux niveaux, integrant stabilisation et supervision, a été developpee et mise en opération. La regulation est réalisee par une combinaison de contrôleurs Moore de type PID. Le monitoring et la stratégie de contrôle a base de règles soot implantés sur des micro-ordinateurs de type PC/486 avec les logiciels ProcessVision et Comdale/C. Les principaux aspects de Ia stratégie de contrôle sont décrits dans cet article et les résultats obtenus soot présentés et discutés."

Jan 1, 1995

By D. B. Langford, R. Hart

"This paper presents an overview of the state-of-the-art in industrial and utility power metering and control systems with particular emphasis on Digital Power Meters and Power Demand Controllers.IntroductionModern micro-processor technology, combined with very fast, high accuracy analog to digital converters, is rapidly allowing economical, digital power instrumentation systems to replace the traditional electro-mechanical meters and equipment previously used for instrumentation, control and protection in industrial power systems. Consequently, instrumentation and Supervisory, Control and Data Acquisition (SCADA) systems that were only practical for the very large utility or user are now available to smaller utilities and users. The information available includes sequence of event recording, trend logging, energy management cost allocation and automated load control, among others. The heart of any power monitoring system is the Digital Instrumentation Package (DIP) . These ""DIP's"" include Digital Power Meters (DPM's) and Power Demand Controllers (PDC's) as well as other specialized instrumentation packages such as Mini RTU's."

Jan 1, 1991

By B. A. Kjarsgaard, C. J. Mwenifumbo

"Abstract - Natural gamma-ray measurements were made in the GSC Smeaton drillhole as part of the borehole geophysical classification of kimberlite pipe 169. In addition, forty samples of Cretaceous sediments (shales, siltstones, and sandstones) and thirty-five kimberlite samples, selected from the drill core, were analyzed for major and trace elements. These elements included potassium (K), uranium (U), and thorium (Th), which are the main naturally-occurring radioactive elements.Different phases of the kimberlite, and the Cretaceous sediments which show variations in the gamma-ray activity, can be easily delineated on the gamma-ray logs. The gamma-ray logs indicate that the radioactivity in the kimberlite derives mainly from Th, and, to a lesser extent, U. Most of the kimberlite units are enriched in Th and U relative to the Cretaceous sediments, and these radioelements are mainly hosted by accessory apatite and perovskite, and minor zircon. Potassium concentrations are low in the kimberlite. The higher K concentration in the sediments clearly distinguishes the Cretaceous sediments from the kimberlite.The U/K and Th/K ratios show important and distinct differences between the two major types of volcaniclastic kimberlite. Kimberlite lapillistones have higher U/K and Th/K ratios than the olivine crystal tuffs. Furthermore, standardized U/K and Th/K geophysical logs can be used to separate marine reworked olivine shoreface sands from other shallow marine sediments that contain kimberlitic detritus. The identification of different phases and/or stratigraphic facies of kimberlite on the basis of radioelement distributions means that gamma-ray spectrometry can assist exploration, particularly in regard to diamond grade distribution."

Jan 1, 1999

By Michael L. Wayman

Native copper is copper which exists in nature in elemental, metallic form, rather than being chemically combined as is the case with the more usual oxides, sulphides, carbonates, etc. Several other metals, including gold, silver and platinum also occur in native form as do, rarely, iron, lead and mercury; a few naturally occurring native metal alloys, notably electrum (gold-silver) and tumbaga {gold-copper or gold-silver-copper) are also known. An analysis of the relative availabilities of native metals as nuggets in a useful size range111 shows native copper to be by far the most abundant of the native metals, exceeding both gold and silver by at least two orders of magnitude. While such an estimate is crude, it serves to illustrate why copper was one of the first metals to have been used by ancient peoples. Native copper is known to occur on all inhabited continents, although its exact occurrence and abundance in ancient times cannot be unambiguously determined because many surface deposits may have been totally exploited and are therefore no longer identifiable. It is clear, however, that native copper does or did occur in all areas inhabited by the early metal-using cultures, for example in the Andes, in Central America and in the Near East. It is remarkable that most of the world's native copper occurs in the deposits of the Lake Superior region, primarily on the Keweenaw Peninsula of northern Michigan and on Isle Royale, an island in Lake Superior some 50 miles north of the Keweenaw deposits. Canadian deposits of native copper are found in Newfoundland and Labrador, Nova Scotia, Quebec, Ontario, British Columbia, the Yukon and the Northwest Territories (on Victoria Island, Bathurst Inlet and the Coppermine River area). It was to locate the latter deposits that the explorer Samuel Hearne was sent overland from Hudson's Bay in 1770; they were also surveyed by Sir John Franklin's expeditions in the 1820s.

Jan 1, 1999

The mixer that is commonly encountered in hydro metallurgical operations consists of a single turbine and tank combination. However, it would be advantageous to examine some common solvent extraction mixing systems in the light of the fundamentals of chemical reactor design. The basic concepts of reactor design are commonly used in the chemical industry, and it should not be too difficult to apply them to solvent extraction. The factors that affect the engineering design of a reactor are: the reacting system; the type of reaction; and the configuration of the reactor. The reaction system in solvent extraction consists of a heterogeneous liquid phase, involving two immiscible liquids. It is essential f or the process that the reactor product can be separated efficiently in the subsequent settler. The type of reaction in solvent extraction system may be quite complex, and the picture is complicated by the presence of competing and side reactions. The reactors themselves have been generally continuous stirred tanks, and the nature of the mixer-settler makes it unlikely that the pumping mixer can be dispensed with. However, it appears that there should be some definite advantages to a system of stirred reactors in series. The kinetic experiments which are carried out should have the definition of optimum reaction conditions as one of their goals. The data obtained from these experiments must also be applicable to the design of reaction equipment. Reactor selection and design is often a unique problem for each chemical process, and does not lend itself to a systematic general approach. However, the application of chemical and physical principles to mixer design in solvent extraction should result in practical, more efficient plants.

Jan 1, 1979

By Carlos Palacios M., Brian K. Townley

"Abstract - The mainland Aysén region of Chilean Patagonia (44°15' - 47°30'S) is a representative segment of the South American active continental margin, distinct with respect to northern and central Chile. Mineralization consists mainly of polymetallic deposits, with important Zn-Pb mines and more recently discovered Au-Ag deposits, unlike the central Andes, which are dominated by Cu mineralization. On a regional scale, rocks may be grouped in four main map units: 1) the Paleozoic metamorphic basement; 2) upper Jurassic-Cretaceous calc-alkaline volcanic and marine sedimentary rocks; 3) the Patagonian batholith, and 4) upper Cretaceous to Miocene basalts and marine and continental sedimentary rocks. The upper Jurassic-Cretaceous rocks and the Patagonian batholith formed in a volcanic arc and back-arc setting superimposed on the Paleozoic metamorphic basement.Based on geographic location and geologic and tectonic setting, ore deposits in this region are assigned to three groups, from south to north: El Faldeo, Fachinal, and El Toqui. The El Faldeo group (south of 47°05'S) includes upper Jurassic Zn-Pb skarn and associated polymetallic massive sulfide vein deposits locally overprinted by Au-rich epithermal mineralization, hosted by volcanic and sedimentary rocks and/or by rocks of the metamorphic basement. The Fachinal group (46°05' - 47°05'S) consists of volcanic-hosted lower Cretaceous Au-Ag epithermal deposits, except for the Mina Silva and Manto Rosillo deposits, which are metamorphic basement-hosted Zn-Pb skarns. The El Toqui group (44°30' - 46°05'S) comprises lower Cretaceous Au-rich Zn-Pb skarns and associated polymetallic veins, as well as Au-Ag-rich epithermal deposits, hosted by volcanic, intrusive, and marine sedimentary rocks. Galena lead isotopic signatures for each deposit group indicate a decreasingly radiogenic trend from south to north, suggesting different lead sources or differences among underlying crust. Three metallogenic provinces and two metallogenic epochs are proposed for the Aysén region: the El Faldeo metallogenic province of Late Jurassic age; and the Fachinal and El Toqui provinces of Early Cretaceous age. Résumé - La partie continentale de la région d’Aysen (Patagonie chilienne, 44°15' - 47°30'S), est unsegment représentatif de la marge continentale active d’Amérique du sud, différent des segments du nordet du centre du Chili. La minéralisation, qui consiste essentiellement en des dépôts polymétalliques, avec d’importantes mines de Pb-Zn, et des dépôts d’Au-Ag récemment découverts, différe de celle des Andes centrales où domine la minéralisation cuprifère. A l’échelle régionale, les roches peuvent être regroupées en quatre unités cartographiques principales : 1) le socle métamorphique paléozoïque, 2) les roches volcaniques calco-alcalines et les sédiments marins du Jurassique supérieur-Crétacé, 3) le batholite patagonien, et 4) les sédiments marins et continentaux ainsi que les basaltes du Crétacé supérieur-Miocène. Les roches du Jurassique supérieur-Crétacé et le batholite patagonien, formés dans un contexte d’arc volcanique et d’arrière-arc se superposent au socle métamorphique paléozoïque.Fondé sur la localisation géographique ainsi que sur le cadre tectonique et géologique, les dépôts de minerais de cette région se répartissent en trois groupes, du sud au nord, El Faldeo, Fachinal et El Toqui. Le Groupe El Faldeo (sud de 47°05'S) contient des skarns à Pb-Zn du Jurassique supérieur associés à des veines de sulfures massifs polymétalliques, localement recoupées par des minéralisations épithermales, riches en Au, et contenus dans des roches sédimentaires et volcaniques et/ou dans des roches du socle métamorphique. Le Groupe Fachinal (46°05' - 47°05'S) consiste en des dépôts épithermaux Au-Ag, se trouvant dans des roches volcaniques du Crétacé inférieur, excepté pour les dépôts de la Mine Silva et Manto Rosillo, où des skarns à Pb-Zn, se trouvent dans le socle métamorphique. Le Groupe El"

Jan 1, 1999

By Pierre Sauvé, Guy Perrault, Armand Savoie, Pierre Trudel

"La Mine Doyon est une entreprise détenue à parts égales par Cambior Inc. et par Minerais Lac Ltée qui en est l'opérateur. Les statistiques de production au 1"" janvier 1990 indiquent que, depuis le début de son exploitation (1980), 10.3 Mt de minerai d'une teneur moyenne de 5,9 g Au/t ont été usinées. Les réserves sont estimées a 10,4 Mt à une teneur moyenne de 6,6 g Au/t jusqu' à une profondeur de-450m.Trois zones minéralisées sont présentement en exploitation. Ces zones sont caractérisées par la présence de veines de quartz-pyrite accompagnées localement de chalcopyrite. Les roches encaissantes sont les schistes a séricite (zone# 1), les roches volcaniclastiques de composition felsique (zone #2) et intermédiaire (zone #2, zone ouest) ainsi que les roches intrusives appartenant au pluton de Mooshla (zone ouest). Toutes ces roches ont subi un métamorphisme régional dont l'intensité correspond à la limite supérieure du facies schiste vert ( -425°C}.Les zones minéralisées sont situées à I' intérieur des zones de déformation et d'altération les plus intenses. L'étude des structures mineures nous indique que la région a subi plusieurs épisodes de déformation ductile a fragile qui sont antérieurs, contemporains et postérieurs al a minéralisation. L'analyse structurale indique également que la déformation majeure est associée à une importante phase de compression orientée N-S a NNE-SSW.L’ensemble des observations suggère que la minéralisation et I' altération associée sont de type épigénétique. La mise en place du minerai se serait effectuée à la fin de l'épisode principal de métamorphisme et de la déformation."

Jan 1, 1990

By R. D. Browns

In his Budget Speech on March 31, 1 977, the Honourable Donald S. Macdonald expressed concern about the financing of investments through new equity issues. He mentioned the need to render more attractive participation in the equity market by investors in all in come brackets. One of the measures introduced in the budget to accomplish this goal is the proposal to increase the dividend gross-up and tax credit in respect of most dividends received by an individual from Canadian companies. The following comments and tables serve to illustrate the impact of this particular proposal.

Jan 1, 1977