Search Documents

By C. B. Webber, L. S. Diaz

"The paper presents the approach taken by Craigmont Mines to grinding circuit control. A detailed description is given of a fully automatic control system which bases its control actions on the continuous measurement of particle size in the cyclone overflow stream. The control system holds a specified particle size in the cyclone overflow, and grinds rod mi 11 ore feed at increased rates. The principles of operation of the system used for continuous measurement of particle size are described, end the improvements in mill throughput and copper recovery over several months of continuous operation are presented.INTRODUCTION Craigmont Mines Limited is located in the south-western interior region of the province of British Columbia, approximately 230 road miles north-east of Vancouver, and ten miles west of the town of Merritt. A moderate climate, good roads and service facilities provided by the Canadian Pacific Railway, Inland Natural Gas Company, and the B.C. Hydro and Power Authority, have provided a very favorable mine and plant site.The preliminary metallurgical design of the Craigmont mill was based on the test results of samples obtained from the original 2500' level drift during 1959. Pilot plant runs and other research testing for design pur¬poses were conducted at the Canadian Exploration Ltd. Laboratory, at Salmo, B.C. The design flowsheet was altered in progressive stages from 2,000 to 3,000, and finally 4,000 tons per day as the ore reserves became better defined. Construction work on the 2,400' level mill site commenced in late 1960. The official opening of Craigntnt Mines Limited took place on September 15, 1961, a little over two years from the time of the metallurgical assessment of the original ore samples.Mill throughput to date has varied widely both on a daily and a monthly basis, due to the varying hardness of the mine ores. The grindability af the ore appears to be related to the oxide iron content, which varies from lows of 9% to highs of 20%. Daily tonnage has ranged from 5,000 tons per day with 10% iron in the feed, to 6,000 tons per day with 20% iron feeds."

Jan 1, 1973

By Douglas W. Reeve, Hoc Nghia Tran, David Barham

"In kraft pulp mills, the spent pulping liquor is concentrated and used as fuel in the recovery boiler. Extensive deposits are formed in the upper section of the boiler due to the very high ash content of the fuel and the volatite nature of the ash. Deposits are composed of Na2S04, Na2C03 NaCI, some potassium salts and reduced sulphur compounds. Chloride and potassium salts are enriched in the deposits compared to the smelt due to their greater volatility.Severe corrosion of the superheater tubes in a recovery boiler has been traced to three factors: a non-uniform temperature profile in the flue gas, relatively high operating steam temperatures and high chIoride and potassium concentrations in the fireside deposits.The role of chIoride and potassium in superheater corrosion has been explained by increased Iiquid phase in deposits. Together with corrosion studies, this information has shown that kraft recovery boiler superheater corrosion due to the chloride and potassium enriched deposits can be avoided by proper boiler operation and by judicious superheater and furnace design.IntroductionThis investigation of recovery boiler superheater corrosion was initiated by the discovery of severe corrosion of the final stage superheater in a Canadian closed cycle kraft pulp mill(1,2). Metal wastage leading to tube failure was believed to be due to three major causes : the relatively high operating steam temperatures, the uneven distribution of flue gas temperature across the boiler which created a "" hot spot"" and the high chloride and potassium concentrations in the superheater fire side deposit. The mill responded to the problem by i) lowering the superheater steam temperature from 475°C to 380°C, ii) minimizing the chloride content in the spent pulping liquor, by controlling the NaCI input with recovered bleach plant effluent, and iii) changing metallurgy of a portion of the bottom section of the final stage superheater platens from ferritic steel T-22 (2.25% Cr, 1% Mo) to austenitic steel Incoloy 800H (21% Cr, 32% Ni, 46% Fe, 1.5% Mn, 1% Si, 0.6% Al) (Fig. 1). Details of the superheater corrosion experienced in the closed cycle mil! have been reported in previous papers(l ·2,) ."

Jan 1, 1984

By V. Concha, M. Hashemzadeh

"The objective of this study was to gain a better insight into the kinetics of chalcocite leaching in an acidic ferric sulfate media. Chalcocite leaching in acidic media is known to occur in two sequential stages, with the first stage being much faster than the second. The leaching residue from the first stage is typically assumed to be a covellite type of material. This study hypothesized that the mineralogy after the first-stage leaching varies in response to different leaching conditions. We investigated the dependency of the mineralogy of the first-stage leaching residue on temperature and initial ferric concentration. The experimental results showed that chalcocite leaching behavior altered upon temperature and initial ferric concentration. A proposed combined reaction model was found to be able to describe the experimental data. The first stage was described very well by the shrinking core diffusion model while the second stage was described very well by the shrinking core chemical reaction model. This finding has important implications for mine operations to manipulate leaching conditions to create the desirable leaching kinetics.INTRODUCTION The kinetics of chalcocite leaching in sulfate media has been extensively studied (Cheng & Lawson, 1991; Fisher, 1994; Fisher, Flores, & Henderson, 1992; Niu, Ruan, Tan, Jia, & Sun, 2015). Sullivan (John D. Sullivan, 1930) proposed a two-stage process for chalcocite leaching in an acidified ferric sulphate solution. The two-stage leaching of chalcocite is presented as the following reactions:"

Jan 1, 2017

By P. C. M. Knops, K. Rijnsburger, R. M. Santos

To overcome the challenges of mineral CO2 sequestration, this work utilizes a unique proprietary Gravity Pressure Vessel (GPV) reactor technology, and focuses on reaction products of high economic value. The GPV provides intense process conditions through hydrostatic pressurization and heat exchange integration that harvests exothermic reaction energy. Here, laboratory-scale tests of the envisioned process was performed in tubular and continuously stirred tank reactor (CSTR) autoclave reactors. The mineral used was Olivine (~Mg1.6Fe2+0.4(SiO4) + ppm Ni/Cr), although asbestos, steel slags and oil shale residues are also under investigation. The effect of several process parameters on reaction extent and product properties was tested: CO2 pressure, temperature, residence time, additives (buffers, lixiviants, chelators, oxidizers), solids loading, and mixing rate. The products (carbonates, amorphous silica and Chromite) were physically separated (based on size, density and magnetic properties), characterized (for chemistry, mineralogy and morphology) and tested in intended applications (e.g. as pozzolanic carbon-negative building material). Economically, it is found that product value is the main driver for mineral carbonation, rather than, or in addition to, the sequestered CO2. The approach of using a GPV and focusing on valuable reaction products could thus make CO2 mineralization a feasible and sustainable hydrometallurgical process.

Jan 1, 2015

By A. Khan, C. Ciriello

The purpose of this paper is to demonstrate the value of constraint modelling in optimization of mineral processing systems. This will be achieved by first understanding the overall concept of variation and constraints present in any system. Next, the value of using a Constraint Model in optimization is demonstrated through comparison of business cases. The benefit of understanding the severity of constraints and movement of the bottleneck within a mineral processing system will be understood through the use of a case study. Paper will conclude with a summary of all optimization benefits that utilization of a constraint model can bring.

Jan 1, 2015

By J. W. Hendry

"This paper will discuss the application of tools and the evolution of computer-assisted procedures in the production planning process at Quintett e Coal Limited (QCL). In 1986, QCL produced 5.3 Mt of clean coal from their surface mining operation located in north eastern British Columbia. The structural complexity of the sedimentary deposit and high rate of mining necessitate the consideration of large amounts of geological information which continually updates the interpretation. There are multiple unit operations required during the process of mining through a given multi-seam sequence, which results in many interdependent faces, and multiple iterations of scheduling sequences in order to satisfy a given set of objectives. In order to facilitate these activities in a timely fashion, it was recognized that a computer systems' capability needed to be developed which could increase the efficiency of information input, manipulation and output. IntroductionQuintette Coal Limited (QCL) has been operating a large metallurgical open pit coal mine in northeastern British Columbia, since 1982. The mine produced 5.3 Mt of clean coal in 1986 for export to Japan. Throughout the start-up period and the subsequent build -up of production levels, it became evident that the primary producing area was comprised of extremely complex faulted structures. This has resulted in development and modification of specialized mining methods employed to effectively recover the resource. Similarly, the planning and engineering techniques employed have been evolved over the same period of time. The implementation of computerized methods has been one of the major developments in this process, including geology interpretation, modelling, reserve definition, quantification, production planning and scheduling, and graphical plan presentation. These capabilities have been employed, in various forms, for project scale feasibility work and long range planning for some time, however, the use of computer tools for short-term, detailed production planning of a complex mining environment presents a different set of problems. It is hoped that a presentation of the current state of evolution and future plan s for development will be of interest to organizations considering implementation of a similar system."

Jan 1, 1988

By K. R. Barnard, K. D. Marte, T. V. Gamarano

"The first commercial scale application of CSIRO’s direct solvent extraction (DSX) technology has been in operation at the Boleo project in Mexico since December, 2015. In this application, DSX is a synergistic solvent extraction system consisting of the extractants LIX 63 and Versatic 10 for recovery of cobalt and zinc from a solution background of manganese, magnesium, and calcium. Key operating parameters such as metal extraction, phase disengagement and extractant stability are summarized and discussed in this paper.INTRODUCTION Commissioning of the Boleo processing plant, located on Mexico’s Baja peninsula, began with the copper circuit starting in late 2014, with first copper cathode production achieved in January, 2015. The cobalt and zinc circuits began commissioning in December, 2015 with first zinc sulphate monohydrate (ZSM) and cobalt cathode production achieved in February and April, 2016 respectively. The Boleo project flow sheet and development has been described in detail in previous publications (Dreisinger, et al. 2005; Dreisinger, Baxter, & Molnar, 2006; Dreisinger, et al. 2008; Dreisinger, et al. 2009) and is summarized schematically in Figure 1. Boleo is a mixed oxide/sulphide Cu-Co-Zn-Mn high clay deposit that is processed in a whole ore, atmospheric, oxidative and reductive, sulphuric acid/seawater leach. Copper is recovered as cathode by conventional solvent extraction and electrowinning. Cobalt and zinc are recovered, from a solution background of manganese, magnesium, and calcium, by CSIRO’s synergistic solvent extraction technology Direct Solvent Extraction (DSX). Cobalt and zinc are bulk stripped from the DSX circuit and then further purified by phosphinic acid solvent extraction to produce zinc sulphate monohydrate granules via spray dried granulation and cobalt cathode rounds via divided cell electrowinning."

Jan 1, 2017

By R. H. Duval

"In May 1936, Pamour started producing gold by cyanidation of flotation concentrates, and in 1939 was milling about 1, 600 tons per day.Refining records dating from 1939 show two oil-fired furnaces in use, (Rockwell type 46 11 x 29 11 inside oval shell).Refining time averaged 7. 83 hours during the year 1939, indicating a complete refining shift of about 9. 33 hours. That year appears to be characteristic of the period with regard to time required and results obtained.For that year total fineness (gold + silver) of the bars averaged 940 (approx.), but it frequently dropped below this figure, sometimes far below.Furnace lining life varied widely from three to seven or more months. Sillimanite was the standard lining but Mullfrax 41 was frequently used.For many years refining practice remained practically unchanged, and in 1960 procedure still consisted essentially of mixing a flux(% Composition Borax 41, Silica 11, Soda-Ash 11, Nitre 15, Mn02 22) with cyanidation precipitate in the ratio of l. 2 to l and heating to a medium heat (yellowishred, 2000° F) with a low flame for a long time. Time required was about 10. 5 hours per refining. Results were still much as detailed above.At this time it was decided to revise refining procedure, in an effort to shorten refining time and obtain consistently good bullion fineness."

Jan 1, 1965

By K. Webb

At both the international and country level, the issue of how the mining sector and indigenous populations should engage on issues of mutual interest or concern has emerged as one of central importance and controversy; involving the mining industry, Aboriginal communities, governments, the courts, and other stakeholders. At its heart, stakeholder engagement is an ethical issue, although it manifests itself in international instruments, domestic laws, industry guidance and agreements. At the international level, the concept of ?free, prior and informed consent? (FPIC), while not subject to widespread agreement on the finer details of evolving definitions, seems to be emerging as an increasingly recognized engagement norm. Within Canada, through a series of decisions, the Supreme Court of Canada (SCC) has articulated a fiduciary obligation of the Crown to consult with and accommodate impacted Aboriginal groups on resource management issues. Provincial governments have been variously attempting to adjust their resource management regimes to stay in alignment with SCC and lower court decisions. Mining sector organizations, working with First Nations partners, have developed agreements to work together for mutual benefit. At the individual mine and community level, there have been instances of constructive engagement, as well situations of physical resistance and legal challenges. The purpose of this paper is to examine the potential impact of new rules under the Ontario Mining Act introduced in 2012 and taking full effect in 2013, which amongst other procedural specifications, addresses the issue of mining industry-Aboriginal consultation in exploration and development activities. Leading up to the passage of the regulations, representatives from some junior mineral exploration companies have been highly critical of the new rules. Similarly, there have been a range of responses to the new rules from some in the First Nations community. The paper will review the regulation in terms of its apparent alignment with SCC decisions and the international norm, compare the regulations with existing mining sector organization guidance documents, and it will draw on the stated perspectives and commentaries of First Nations communities, mining firms, governments, nongovernmental organizations, and others. Building on the foregoing, the paper will provide a preliminary analysis of the perspectives and potential impacts of the new regulation on various stakeholders, and on that basis, possible avenues for further consideration will be suggested.

Aug 1, 2013

By Vicken Aprahamian

"The Royal Canadian Mint (RCM) operates a gold and silver refining toll operation in Ottawa, Ontario, Canada. The silver refining line is a recent addition and was commissioned in 2005. One source of silver in the refinery is from gold doré which undergoes Miller chlorination before electrorefining to 99.99% cathode gold. Treatment of the Miller salt or silver-copper chloride produced consisted of a 2-stage high temperature reduction process step using soda ash prior to 2005. Copper-rich silver bars were produced and shipped offsite for further refining.The copper-rich bars could not be blended into sufficient high grade silver doré to dilute the copper and allow electrorefining in a silver nitrate medium. A new wet process was developed and commissioned to replace the high temperature reduction and allow removal of bulk copper. Thus upgraded impure silver produced was cast into anode for electrorefining to 99.9% purity silver flake. The 2005 RCM Hydromet Slag process is presented as well as its more current version. In addition, mention is made of a novel processing scenario for the introduction of Miller chlorination silver into the electrorefining circuit."

Jan 1, 2015

By Sabine Noelte, Mikko Petteri Rantamäki, Christopher Robben, Anssi Takala, Karl-Erik Rånman

"Sensor-based ore sorting is on its way to establish as a standard option for physical separation. The increasing number of installations in coal, iron ore, industrial minerals and hard-rock metal mining segments underlines the technological and financial potential that is beginning to be untapped. The Ma’aden Phosphate installation with 1.650 t/h sensor-based ore sorter feed sets a new benchmark for the possible capacity of stationary installations. Besides stationary installations, including multiple sorters parallel in different size ranges and multiple stages, containerised semi-mobile plants are applied. These offer two advantages, first being the reduction of transport costs when applied close to the mining face. The second is that semi-mobile systems enable processing of tens of thousands of tonnes of ore in a piloting phase with an approximate duration of 0.5 to six months, verifying the results laboratory mini-bulk tests on 5–10 tonnes of sample. This is especially important for low-grade metal ores because of the inherent Fundamental Sampling Error, as well as the Grouping and Segregation Error. The paper elaborates the results achieved within the I2MINE project, treating polymetallic ore at the Boliden Concentrator in Sweden.INTRODUCTIONSensor-based ore sorting (SBS) is becoming a standard option for physical separation, applied in all segments of mineral production. The Umm Wu’al project sets the bar for stationary SBS installations with 1,650 t/h feed (TOMRA, 2015). TOMRA Sorting Solutions has finalised an agreement in cooperation with Outotec to supply Outotec-branded sorting solutions for the mining and metallurgical industry (TOMRA, 2014). Especially for low-grade hard rock metal ores, an interdisciplinary approach is necessary applying experts for all aspects of mineral production. Due to the impact on the whole process stream, it is important on the end user side to have high level managerial support and involve all disciplines to ensure that all stake holders are involved in the analysis."

Jan 1, 2016

By R. G. McDonald

"High iron solution concentrations often result in the formation of basic ferric sulfate during the high temperature oxidation of sulfidic materials such as base metal and refractory gold concentrates. Consequently, the “Hot Cure Process” followed by limestone neutralization is required to facilitate subsequent processing and/or disposal of the leach residue. The present paper discusses strategies that can be employed to influence the composition and nature of the high-iron content leach residues produced during pressure leaching.INTRODUCTION Control of iron deportment in hydrometallurgical processing remains a key challenge for a range of reasons. Strategies generally relate to the control of conditions under which iron is optimally rejected (Demopoulos, 2009). Supersaturation provides the driving force for crystallization and this can be controlled by a number of factors that include (1) pH and/or Eh control, (2) the presence of matrix anions and impurities, (3) dilution, (4) complexation and dissociation and (5) manipulation of the rate at which the metal to be precipitated is released to solution. Each of these factors is impacted by temperature. Good control of crystallization is essential to the control of precipitate properties such as the degree of crystallinity, stability, particle size and quality which covers both the extent of impurity uptake and suitability of the precipitate for waste disposal. The quality and properties of iron precipitates in turn can impact downstream processing. It is the aim of this paper to discuss the generation of iron-containing residues produced during the pressure oxidation of sulfidic ores and concentrates and how the nature of these can be controlled to potentially facilitate further processing. A brief overview of several related topics will now be given and include, where relevant, discussion of work undertaken in our laboratories. In addition, brief discussions of selected process options that enable good control of iron rejection will be provided."

Jan 1, 2016

By I. Farr, M. R. Mock, J. C. Robison

"HPAL and POX autoclave vapor-space gasses are vented through an autoclave PCV (Pressure Control Valve). The downstream steam-born mist of liquid droplets and solid particles travels in excess of 1000 m/s with megawatts of kinetic power at temperatures up to 160 C. The characteristics of downstream states often result in problems with corrosion, erosion, noise and vibration. Comprehension of those and related characteristics aids in improved pressure control, overpressure control and autoclave level control. We introduce compressible multiphase flow concepts and constructs germane to such flow including choked flow, continuous phase change, shock waves and supersonic flow plumes. Flow modeling based on first principles quantitatively predicts such flows providing a tool for component sizing and a method to estimate effects of water injection on flow. Insight deduced from modeling aids in mitigation of afore mentioned problems of which we share some from-site examples.INTRODUCTION First principles related to fluid thermodynamics and compressible flow have been employed akin to their application in the rocket industry. We will present the results of the application of those principles conceptually and authentically without mathematical rigour while using language of the pertinent disciplines. The autoclave (AC) vapor space over the slurry of a POX (Pressure Oxidation) or HPAL (High-Pressure Acid Leach) system (depicted in Figure 1) is vented via a PCV (pressure control valve) followed by certain ducting, and perhaps a nozzle, before exiting at atmospheric (typically) pressure. As indicated by its name the PCV controls the AC pressure as the flow control component of a pressure control loop."

Jan 1, 2017

By Janice Zinck, Ian London

In recent years, the secure supply of critical and technology metals has become increasingly important tomajor industrialized economies that seek to sustain their industrial base and develop advanced technologies, such as clean energy. Canada, with its significant reserves of rare earth element (REE) and other metals, has an opportunity to supply some of the global demand for these materials. However, to transition from promising mineral deposits to marketable products, investment in strategic research and development (R&D) and expertise is needed to address the complex technological challenges around the production, separation and processing of these metals, and to better understand the global market for these key commodities. To this end, in its April 2015 budget, the Government of Canada committed to invest $23M over 5 years to accelerate production of REE and chromite/ferrochrome. The goal of this program, developed in close association with industry, is that Canada contributes a sustainable supply of REE to the global market. The research and development program will provide the technological capacity to establish a Canadian REE industry. This paper will discuss REE R&D advances achieved in the first year of the program in areas of mineral characterization, beneficiation, leaching, separation and environmental management and will highlight the Canadian model of collaboration where industry (e.g. prospective producers, technology companies), government, academia and other stakeholders work closely to ensure that the R&D is targeted, innovative and effectively deployed and commercialized.

Jan 1, 2016

By Daan Maijer, Wade Marquardt, Robert MacKay, Steven Cockcroft, Farzaneh Farhang Mehr

"To comply with the new Corporate Average Fuel Economy (CAFE) standards, the automotive industry is aiming to reduce weight and increase the power and efficiency of small displacement engines through the application of forced induction technologies. As an example, there are now several 2.0 litre turbocharged engines in production, producing in excess of 240 hp. To meet the need for improved fatigue properties in the engine blocks used in these high-output engines, a new water-cooled chill technology is under exploration at UBC in partnership with General Motors and Nemak. A series of experimental techniques were used to assess the capability of the new chill to extract heat from an A319 casting in the vicinity of the main bearing bulk head. The results show that this method has the potential to achieve a reduction in secondary dendrite arm spacing thus meeting the new microstructural specifications for these engines.INTRODUCTION The automotive industry is working to meet the stricter efficiency requirements laid out within the CAFE (Corporate Average Fuel Economy) regulations (Bastani, 2012; Cole, 1995; Mackay, 2011; Miller, 2000), while at the same time not sacrificing performance. One approach is to increase the use of lightweight materials, which leads to a decrease in the overall vehicle weight and fuel consumption (Cole, 1995; Mackay, 2011; Miller, 2000). Other approaches include smaller displacement engines and gas-electric hybrid drivetrains. However, one trend that is becoming clear, is a greater emphasis on force induction gasoline engines. This allows for weight reduction to be achieved with smaller displacement engines without sacrificing performance. One consequence of this approach is that the engine block materials are subject to higher in-service thermal and mechanical cyclic loads (Cole, 1995; Miller, 2011; Heysler, 2001) The fatigue properties of an alloy are strongly affected by a number of the, as-cast, microstructure features including, Secondary Dendrite Arm Spacing (SDAS), porosity and eutectic lamella spacing (including intermetallic ß-Al5FeSi platelets) (Mackay, 2010a; Mackay, 2010b; Viet-Duc, 2015; Casellas, 2005). It is generally accepted they can act as fatigue initiation sites and that a reduction in their size will result in an improvement in fatigue performance. For a given alloy chemistry, one of the key parameters affecting the length scale of all three is cooling rate (Mackay, 2000)."

Jan 1, 2017

By China University of Mining and Technology, P. Zhang, C. Zhou, C. Duan

"Recovering pyrite from the gangue with high sulfur content is of great significance for both economic development and environment protection in China. Due to the global water shortage and high cost in wet separation processes, it is urgent to explore more efficient energy and water conservation method in mineral processing field. This study has proposed an innovative method based on density difference for fine pyrite enrichment by vibration fluidized bed. In this study, the total sulfur content (TSC) of the gangue sample is 19.18%, and the pyrite is disseminated with fine granularity in the gangue which should be crushed for dissociation. The combination and dissociation experiment of -6mm gangue shows that the dominant density of -6+3mm, -3+1mm and -1+0.5mm comminuted material is +2.9g/cm3. Based on the analysis of characteristic, the effects of various factors on the separation performance were experimental studied. The results show that gas velocity, vibration intensity and bed height all have the significant effects. With the increases of superficial gas velocity, vibration intensity and bed height, the separation performance all presents a decreasing tendency. Additionally, the TSC of -6+3mm, -3+1mm and -1+0.5mm materials are respectively up to 37.94% , 35.43% and 30.61% at the optimum conditions, which are the 1.72?1.90 and 2.29 times as much as the TSC of raw material, respectively. This study demonstrates the vibrated fluidized bed can recovery pyrite from the gangue effectively.INTRODUCTIONWith the increasing mining and separation of coal, the yield of gangue has a further growth tendency, which has become one of the largest reserves of industrial waste (Querol et al., 2008). However, many harmful elements, such as S?NOx and Hg, is existed in the gangue leading the serious damage to the soil and environment (Hao, Yun, Zhanyuan, Sen, & Song, 2013). In addition, the economic would be suffered from the loss resulting in the occupied of arable land caused by the accumulation of gangue (Yeheyis, Shang, & Yanful, 2009; Zhou, Liu, Yan, Fang, & Wang, 2012). Therefore, the government has put forward the policies of ""green mining"" in China (Xing & Gao, 2009; R. Zhang, Ai, Zhou, Ju, & Zhang, 2015; Zheng, Du, Li, Qiu, & Yang, 2015). Among different research areas of coal utilization, extracting the useful minerals has become one of hot topics (Ledin & Pedersen, 1996; P. Patra & Natarajan, 2003; Partha Patra & Natarajan, 2004). At present, many researchers has devoted to the desulfurization of coal all over the world. As result, the sulfur element, which is mainly existed in the presence of pyrite, would transferred in the tailings, namely the gangue. Meanwhile, the pyrite is important raw materials to produce rubber, paper, textile and match. Consequently, recovering the pyrite from the gangue is not only suitable to the requirement of ""green mining"", but it could turn the waste into the treasure having the important significance."

Jan 1, 2016

By C. Chapman, P. Cowx

"INTRODUCTIONTetronics Research and Development Co. Limited has installed several plasma torches for steel heating in continuous caster tundishes. An extensive demonstration program on a 14 tonne tundish reported the following advantages of plasma heating.• close control of steel temperature to ± 5°C;• a reduction of the furnace tapping temperature of up to 20ºC, leading to savings in energy and refractories costs ;• improvement in steel quality, to produce a slab product with an equi-axed crystal structure and a reduced number of large sub-surface slag inclusions;• the virtual elimination of oxygen pickup in the tundish; and• the capability of making ferroalloy trim additions to the tundish to permit a change of steel grade during casting, greatly decreasing inventory costs.The Need for Tundish HeatingIn the continuous casting of steel, the function of the tundish is to transfer the molten metal between the ladle to one or more continuously fed casting moulds. Figure I shows a typical temperature profile of molten steel in the tundish over the first cast cycle. It is observed that a rapid drop in temperature occurs both at the start of the cast, due to the tundish refractories absorbing heat, and also during ladle changeover. In addition, as a result of thermal losses through the ladle sidewalls, there is a gradual decline in the bulk steel temperature over the entire heat cycle. Consequently, in normal tundish operation, it is necessary to cast with a high superheat (25°C to 30°C + above steel liquidus temperature) in order to prevent freeze-up of the strand. Problems of high temperature variation and the potential of the steel solidifying in the tundish are greater for small caster units of low thermal mass . A high steel superheat increases the steelmaking vessel process time and refractory wear and prevents the formation of a uniform equi-axed solidification structure in the cast steel, resulting in centre line segregation and porosity. The large drop in the casting temperature that occurs during unsteady state operation causes an increase in the number of sub-surface inclusions, reducing the value of the product. Accordingly, plasma heating may be employed to maintain the molten steel at an optimum temperature to produce a slab of consistent quality."

Jan 1, 1989

By L. Tafaghodi, A. Hosseinpour

"Silicon is considered as the most appropriate semiconductor material for manufacturing solar cells because of its natural abundance and being nontoxic. The transferable knowledge and technology from the electronics industry and the long history of silicon-based semiconductors are also assisting the domination of silicon as the most common semiconductor material. Developing an environmentally and economically viable process for producing solar grade silicon has been one of the main challenges in the silicon industry in the past few years. Metallurgical refining processes have received significant attention because of their high productivity and low cost. Slag refining is one of the purification methods which is based on oxidation of the impurity elements, followed by its dissolution into a slag phase. This article presents a review of various slag refining processes that have been employed for purification of silicon and silicon alloys. SiO2, CaO, CaF2, CaCl2, Al2O3, MgO and Na2O are the major components of the slags used for silicon refining. These slags can be classified into three main categories including binary, ternary and quaternary slags.INTRODUCTION Silicon can be categorized into three different grades based on its application or purity: metallurgical grade silicon (MG-Si) with purity of ~98 %, solar grade silicon (SoG-Si) with purity of ~99.99999 % and semiconductor grade silicon (SeG-Si) which has the purity of 99.9999999 % (Johnston & Barati, 2010; Krystad, Tang, & Tranell, 2012; Tang, Øvrelid, Tranell, & Tangstad, 2009). Producing SeG-Si is carried out through an energy-intensive and complicated process named Siemens. This purification process is relatively slow and involves using toxic and corrosive reagents (e.g. Trichlorosilane). At present the majority of SoG-Si is produced via Siemens or Siemens-like processes and there is very limited production via processes dedicated to SoG-Si. Because of the difference in silicon specifications required in microelectronics and photovoltaic industry, and the cost and energy associated with the Siemens process, an interest has emerged to develop technologies dedicated to producing low cost SoG-Si (Istratov et al., 2003; Johnston, Khajavi, Li, Sokhanvaran, & Barati, 2012; Mitrašinovic, D'Souza, & Utigard, 2012; Wu et al., 2012)."

Jan 1, 2017

By Brien A. Perry, Art Wiebert

"Many organizations which have implemented Total Quality Management (TQM) are finding that the process has either stalled or is not working so well as originally envisioned. This can be particularly evident in an engineering environment where the uniqueness of engineers and their particular culture has not been adequately considered. Winning the commitment of a highly educated group ojprojemnnJJ1s to the TQM concepts, which are often initially 5W2 as too simplistic poses special challenges.Successful TQM implementations are found among technical groups where employees have significant input into creating the new work culture, feel empowered to make changes and are well trained in teamwork. A coach who is knowledgeable in implementation problems can, when working closely with the technical teams, help them circumvent obstacles and guide them successfully through the difficult early phases. The remaining key ingredient for success is supportive management which leads the change and is both informed and appreciative of the accomplishment being made.This Paper is based on first-hand experience with common problems and results encountered in implementing TQM in an engineering environment. Described in the paper are ways of avoiding these problems through awareness of the unique nature of engineering groups, implementation planning, just-in-time training and coaching people in the TQM process. The paper concludes with a focus on the opportunities and results from a successful implementation. These opportunities and results include the benefits each engineer can realize through process thinking, empowerment and teamwork."

Jan 1, 1995

By R. Pakalnis, H. Miller, Madill. T.

"This paper describes a methodical approach to the estimation of the orientation and the magnitude of in-situ stresses. The study was performed at the Ruttan Mine, Sherritt Gordon Mines Ltd. , a 6,000 T.P.D. underground operation, located in northern Manitoba, Canada. It involves an initial estimate to be made based upon: structural interpretation • virgin stress measurements conducted in other areas (world wide, regional)The verification of the prevailing stress regime was made by conducting CSIRO hollow inclusion(1) overcoring measurements. The current cost for a virgin stress determination is about $7000 per measurement(2) and the difficulty encountered in attaining a good reading is high. This paper will describe the analytical procedures employed at Ruttan in evaluating the in-situ stress magnitude and orientation based on three overcore tests. It is proposed to perform an additional six measurements in order to verify the following results:Vertical stress = av (MPa) = 0.027 by depth (m)Major principal stress = o! """" 2.5 xav (340°/-20°)*Intermediate principal stress = a2 - 1.2xav (070°/0°)Minor principal stress = a3 """" o.8xov (160°/-70°)IntroductionThe Ruttan Mine of Sherritt Gordon Mines Ltd., a 6,000 T.P.D. underground operation, is located in northern Manitoba, Canada (Fig. I). The Ruttan copper-zinc orebody is a multi-lensed, steeply dipping (70 degrees) en-echelon deposit. Individual lenses have a maximum strike length of 350 m with widths varying from 7 m to 61 m. The mining method is o pen stoping with delayed backfilling and extends from surface to 860 m below surface."

Jan 1, 1985