Search Documents

By Saeid Akhavan

Accumulative roll bonding (ARB) is a severe plastic deformation process for achieving ultrafine grains in metallic sheets without changing the sample dimensions. In this study, ARB process was carried out on 5083 aluminum alloy sheets up to 6 cycles. In this process, the surfaces of the strips to be joined are roughened and cleaned and then stacked. After stacking, the specimen is roll-bonded by rolling using a 50% reduction. The rolled specimen is cut into two halves, and the above-mentioned procedure is repeated for several times. Microstructural characterizations were analyzed by transmition electron microscopy (TEM). Tension and Vickers hardness tests were performed on produced sheets for evaluating their mechanical properties. In order to clarify the failure mode, fracture surfaces after tensile tests were observed by scanning electron microscopy (SEM). The results indicated that at the early stages of ARB process, grains were subdivided by deformation induced boundaries. After several ARB cycles, lamellar structure elongated in the rolling direction contains lamellar boundaries was formed. With increasing the strain, mean spacing of lamellar boundaries decreased. Finally, continuous recrystallization resulted in a microstructure covered with small recrystallized grains with an average diameter below 100 nm at the end of four cycle. The tensile strength and hardness of the 6 cycle ARB processed 5083 aluminum alloy sheet increased about two and three times of the initial values, respectively. Results indicated conformity between mechanical evolutions and microstructural changes during ARB process. Fracture surfaces observations showed that failure mode in ARB processed aluminum is shear ductile rupture with elongated small dimples.

Oct 1, 2011

By K. Soldenhoff, M. Fainerman-Melnikova

The use of strong base resins for uranium recovery is severely affected by the presence of chloride ions in solution. In areas where high-quality process water is not readily available, the use of saline water would extend the potential application for ion exchange in uranium processing. This study presents measurements of uranium uptake, using a wide range of commercially available weak base anionic exchangers, from solutions with chloride concentrations ranging from 2.5 to 22 g/L Cl. Out of 14 weak base anionic resins tested, 3 were identified that were not severely impacted by the presence of chloride and significantly outperformed a gel strong base resin typically used for uranium recovery in high-chloride environments. The uranium loading was sufficiently high for the consideration of development of the application of uranium recovery from uranium ores leached with seawater.

Jan 1, 2012

By Yi-xin Zhoa

The characteristics of coal bumps are analyzed based on the microseismic data from No.8935 workface in Xinzhouyao coal mine, Datong Mining Group. The geology of this workface is characterized by the thick sandstone roof and coal seam, both with relative higher stiffness and strength. In order to investigate the mechanism and precursors of coal bumps occurred in No.8935 workface, the locations of microseismic, the relationship of microseismic energy and frequency and the spectrum of microseismic signals are analyzed. The result shows that the coal bumps in No.8935 workface were mainly induced by the seismic caused by roof failure. The coal pillar near the goaf is more easily to bump. The statistics results indicate that the coal bumps were mainly occurred in the gate road near the pillar, less than 50m ahead of mining face and located in the hard roof adjacent with coal seam. Moreover, the frequency, energy, b-value and frequency spectrogram of microseismic events were found to decrease before coal bumps. It was found that the frequencies of the microseismic events before coal bumps mainly concentrate upon 5~60Hz. The sudden decreasing of frequency and increasing of amplitude of microseismic events can be regarded as a precursor of coal bumps.

Aug 1, 2013

By David M. Knowles, R. Gordon Gastil

"The Precambrian sedimentary series of the Labrador geosyncline, including iron formation, extends into southwestern Labrador and adjacent Quebec. The iron formation consisted of primary oxide, silicate, and carbonate facies which were deposited simultaneously in an irregular basin in response to migratory environmental conditions. The iron formation isochemically recrystallized to coarse-grained quartz-iron oxide, iron silicate, and quartz-iron carbon-ate rocks during prolonged regional metamorphism. The rocks are deformed on two deformation axes intersecting at large angles, and are characterized by isoclinal to recumbent folds. Parts of the formation have been profoundly affected by a post-metamorphic leaching and oxidizing environment."

Jan 1, 1959

By J. Oyunaa, P. Munkhbaatar, A. Sarnai

"The molybdenum mining process used at Mongolia Erdenet Company is a selective flotation of molybdenite from the copper porphyry ores in which the extraction of molybdenum comes as a byproduct of the ongoing copper production.The mineralogical composition of molybdenum concentrate is 99.4% molybdenite (MoS2), 0.09% molybdenum oxide (MoO3), 0.52% powellite (CaMoO4) and wulfenite (PbMoO4) and content 47.76– 47.92% molybdenum, 1.5–2.67% copper, 0.04% renium.From compared solvents sodium and carbonate and ammonia are like extracted molybdenum than hydrochloric acid, which contained 96.23–97.72 p.c. of its total amount. Hence to take into consideration abundance, cheap and suitable for analysis and processing the molybdenum concentrate ammonia is choosing as a basic solvent. By direct evaporation of ammonia extract solution, we obtained ammonium ortomolybdate, which contains 73.47% MoO3. INTRODUCTIONMolybdenum occurs in the earth’s crust in an abundance of about 10–14%, mainly as molybdenite, MoS2. Small quantities are also associated with other metals having similar chemical properties. Thus wulfenite (PbMoO4) is found in oxidized parts of sulfidic lead deposits in many regions of the world; powellite [Ca(Mo,W)O4] is a calcium molybdate usually formed from the modification of molybdenite in deposits containing tungsten as scheelite (CaWO4) and tungsten substitutes for molybdenum up to about 10%. Ferrimolybdite (Fe2Mo3O12·8H2O) is the product of oxidation of molybdenite in the presence of iron (III) compounds. Molybdenite is the primary source of molybdenum. Should demand for molybdenum rise so that additional sources become necessary, wulfenite, powellite, and ferrimolybdite may become commercially significant. Molybdenum ore is mined by underground and open-pit methods. A typical primary molybdenum ore body contains 0.05–0.25% Mo, and secondary ore bodies (copper porphyry ores) average 0.3–1.6% Cu and 0.01–0.05% Mo. Flotation remains the preferred and almost exclusive method of upgrading the molybdenite mineral to an industrial-grade molybdenite concentrate containing 90–95% MoS2, the balance being gangue (Habashi, 1997)."

Jan 1, 2016

By L. H. Cole

FOR many years Industrial Minerals, or as they were formerly called, 'the Non-Metallic Minerals', compared with the metallics, were considered of only minor importance and as such were given scant attention in the technical press as well as in the public press. Those days are, however, happily passing, and thanks, to an appreciable extent, to the constant endeavour of the Industrial Minerals Section of this Institute, established in the fall of 1932 industrial minerals are now assuming the importance to which they are entitled. The term 'Industrial Minerals', when first adopted in this sense by the Institute, was thought to be original in its application, but it is interesting to note that it had been used many years previously by the Queensland Geological Survey in the following publication: SALT Article 1 in Industrial Minerals by B. DUNSTAN, Chief Government Geologist (Publication No. 268, in Part) Queensland Geological Survey, Department of Mines, Brisbane 1920 In Queensland, however, the term embraced some of the metals as well as the non-metallic minerals proper. The lead furnished by Canada in this matter bore rapid fruit, and already the term 'Industrial Minerals' is widely used, not only throughout Canada but in the United States as well.

Jan 1, 1939

By K. J. Fair, G. Van Weert, J. E. Schneider

"IntroductionCyanidation is the principal process for extracting gold from ores . Many primary gold ores, however, are partially or totally refractory in the conventional cyanidation process.Considerable success has been achieved with new gold leaching techniques, such as intensive cyanidation, pressure cyanidation, carbon-in-leach cyanidation, etc. These techniques however, do not offer substantial gains in gold extraction from refractory pyrites.The more drastic pretreatment processes such as roasting, chemical oxidation, autoclave oxidation, and bacterial oxidation all utilize oxidation to break down the structures of pyrite and arsenopyrite. This generally renders the gold amenable to cyanidation.Comparative cost studies indicate that the oldest commercial pretreatment method, i.e. high temperature roasting, is currently the least expensive option if the sulphuric acid can be sold. It operates with air at atmospheric pressure and is characterized by fast reaction rates. For an alternative hydrometallurgical con centrate treatment method to be competitive, it too should operate with air at atmospheric pressure and with fast reaction rates. The NITROX process meets these conditions."

Jan 1, 1986

By R. W. Thompkins

MINE operators are concerned with temperature conditions in their mines, particularly the effects of high temperatures on the l1ealth and efficiency of tl1eir employees. This paper is written to focus attention on the variables of heat transfer between rock and air. It illustrates the difficulties of predicting the manner, and the extent, of heat transfer from theoretical concepts, prior to actual operation of a mine airway. There are ~1any sources of heat in mines. The most important is that of the rock surrounding the airway. This heat, in turn, is a product of the age of the rock, faulting, proximity to recent igneous activity, oxidation of sulphides, hot ground waters, etc. The sources of heat may be constant for any one mine, but they are far from constant when dealing with various mining districts or e1•en with a number of mines in the same district. A second source of heat is that produced by machinery in operation. Practically all the waste

Jan 1, 1962

By R. T. Saxon

Prior to November 1975 there were several failures of front -wheel spindles on large haulage truck s in B.C., attributed to fatigue cracks. Since that time, a non-destructive test program has succeeded in detecting the cracks before catastrophic failure, However, the author regards the failures as just one example of a. general unreliability in large high-strength steel castings and urges the industry to look to forgings for sensitive components of heavy equipment.

Jan 1, 1977

By R. Carrier

"There has been a continuous evolution with the use of pre-cast concrete elements in the construction of aluminum smelters. In 1990, Phase I of Alouette was built using cast-in-place concrete exclusively. Whereas, other AP 30 technology plants such as Hillside 2 in the mid-1990s used pre-cast concrete beams with cast-in-place floors. Mozal 2, in 2002, used pre-cast concrete beams with pre-cast partial-slab operating floors. Alouette Phase II went further. Not only were the potroom building beams and floors pre-cast, but the entire pot support system, insulating walls and basement jersey walls were pre-cast. Once the techniques for bending and welding the reinforcement bars and the design for attaching electrical insulating plates to the concrete was perfected, the challenge for the project remained only in the logistics of transporting the pieces to site and simple erection. The overall impact on the project was dramatic. Using prefabricated concrete not only allowed advancement of the schedule, but totally eliminated formwork, re-bar installation, and form removal activities along with the handling of all the materials involved with these activities. With the elimination of these labour and material-intensive portions of the job, exposure to work injuries was dramatically reduced. The most prevalent activity for lost time accidents is during the rough work associated with concrete formwork, placing concrete and form removal. Another area where prefabricated elements were successfully used on Alouette Phase II was for the insulating walls enclosing the pot area, known as the ""claustra walls"". Usually these walls are constructed in-situ using mortar and breeze block. Success was also achieved with prefabrication of the perimetric walls that are installed at the lower floor of the potroom. A big advantage of using prefabricated concrete in the electrolysis area is in assuring electrical isolation for the operating floors. Poured concrete requires a meticulous clean-up effort before commissioning to establish the electrically ""floating"" characteristics of the operating floors. Poured concrete results in ""wash"", stray wood,"

Jan 1, 2006

By G. A. Vissac

IN THE preliminary design of a coal washery, the most important factor to evaluate is the ash content of the final product. The ash content permissible may be imposed by market demands, but, in the final analysis, sooner or later - as most consumers today are buying coal on a 'heat value' basis - the coal operator has a certain margin of latitude. and the ash content of the coal to be delivered can be determined on the basis of maximum returns and highest profits. A few years ago, the most desirable separation was selected on the basis of the plus-minus 0.10; that is, the most desirable gravity of the separation was selected at the point showing a minimum amount of near gravities in the raw coal. The reason for this was an expected wide error over these near gravities. Today with the recent development of cry accurate, automatically controlled cleaning apparatus, a much larger latitude is possible, and the most desirable gravity of separation can be selected, almost exclusively, on the basis of the economic factors involved. To illustrate these new methods of investigation we shall give two examples, based on actual coals from the western United States.

Jan 1, 1957

By Jeff Smith

Agenda About NORTHPARKES The NEED The INITIATIVE The SEARCH The PRODUCTS The SOLUTION The RESULTS The Northparkes copper-gold mine in Central Western NSW commenced operations in 1994. Copper concentrate is produced and shipped to smelters in Japan, China & India under long term contracts with spot sales to other Asian countries.

May 1, 2006

By N. Wachgama, J. P. T. Kapusta, R. U. Pagador

The Thai Copper Industries smelter (Thai Copper) is located some 200 km southeast of Bangkok near the MapTaPhut deep sea port in one of the industrial centres of Thailand. Although construction of the complex started in the mid 1990s, the smelter, acid plant and refinery were completed in 2004. Thai Copper is a state-of-the-art copper smelter processing imported concentrates with a total yearly capacity of 165,000 tonnes of cathodes. It employs the El Teniente Technology where concentrates are blended and smelted continuously in a primary smelting reactor to produce high grade matte or white metal. The white metal is converted in batches to blister copper in Hoboken siphon converters equipped with Air Liquide Shrouded Injector (ALS I) Technology for sonic injection of oxygen enriched air. Final refining is carried out in two anode furnaces prior to anode casting and electrorefining. Thai Copper and Air Liquide Canada executed a technical assistance agreement in late 2005. Pre-commissioning of the shrouded injectors took place in July and November 2006 while hot commissioning occurred in December 2006. This paper presents the major technical aspects of the joint commissioning, including the establishment of operating practices specific to shrouded injection converting. Preliminary results of this first commercial implementation of ALSI Technology in copper converting are also provided.

Jan 1, 2007

By J E. Gordon

For many years, it has been known that certain loud noises may, with prolonged exposure, temporarily or permanently damage a person's hearing ability. Pneumatic rock drills, al-though among the offenders, have, until recently, remained unaltered and unrestricted as to noise output. Now, there are drills available with higher rates of penetration and yet with noise levels reduced to those of previous models or less. Use of such drills, when proved to be superior in noise attenuation and of acceptable performance, should be encouraged in order to reduce future hearing losses to a minimum. People Have the Right to Hear P ERHAPS the earliest recognized indication of hearing loss due to industrial noise was the deaf-ness developed by the workmen in boiler factories. Here, the vibration set up in the shells by the riveting hammers gradually deteriorated the workmen's hearing, especially those whose job it was to hold the dollies inside the drum, where the sound is greatly intensified by reflection

Jan 1, 1963

Mineral engineering is defined as those engineering activities that relate to the discovery, development and utilization of mineral resources. Using petroleum engineering as an example, it is shown that the breadth of the field to be studied is a major educational problem. Breadth of field is aggravated by the rapidity with which technological demands may change. At present, special short courses serve to update engineering education. Recent experience suggests an increased rate of change for the future. The fact that engineers have typically human needs and goals, and the fact that engineers respond to these in our free society, introduces a third class of problems. One approach to the solution of these problems is the unified engineering curriculum based on a core of subject mat-ter common to all engineering. Experience suggests that the unified curriculum is an effective method to minimize the importance of the first two problem areas presented, and shows a degree of success in handling some problems within the third area. Perhaps, for the good of all segments of society, it is best to have both career-oriented and unified curricula represented by educational institutions of high quality.

Jan 1, 1963

By D. M. Maijer, S. L. Cockcroft, A. B. Phillion, P. Fan, C. Reilly, H. Khadivinassab

A combined experimental / numerical approach is proposed to investigate the bulk transfer of solute due to liquid metal feeding during shape casting of aluminum alloy A356 (Al-7Si-0.3Mg). A dumbbell-shaped experimental casting geometry has been developed, which promotes solute redistribution due to liquid metal feeding. The redistribution of solute in trial castings is evaluated based on the area fraction of eutectic phases. In the numerical model, silicon species segregation during solidification are calculated assuming the Scheil approximation, and are coupled with macro-scale solute transport due to Darcy flow in the mushy zone and feeding flow. The model has been implemented within the commercial CFD software, FLUENT, which simultaneously solves the thermal, fluid flow fields and species segregation on the macro-scale. The experimental and numerical results are compared and contrasted to examine the effects of liquid metal feeding in this casting.

Jan 1, 2014

By Wengui Su, Qi Zhang, Junce Wang, Zhijun Ma, Xingyuan Weng

"Mesoporous materials with large specific surface area, pore size, and pore volume have been widely used in many fields such as ion exchange, gas separation, adsorption, and catalysis. Mesoporous materials prepared using natural zeolite have the advantages of both acid and alkali resistance. In this work, mesoporous materials were prepared using natural zeolite as the starting material and diethylenetriamine (DETA) as a template. The resulting samples were characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD) and N2 adsorption-desorption experiments. The influence of the crystallization temperature and crystallization time on the specific surface area, pore volume, pore size, and morphology of the resulting mesoporous materials are also discussed. Our results show that for an increase in both the crystallization temperature and time, the average pore size first increases then decreases, while the specific surface area first decreases then increases. Based on this work, we concluded that the optimal crystallization temperature was 2003 and the optimal crystallization time was 60 h. These conditions gave an average pore size of 17.93 nm, a pore volume of 0.048 cm3g-1, and a specific surface area of 16.48 m2g-1.INTRODUCTIONMesoporous zeolite, as the name implies, is a highly porous crystalline zeolite. This material is of interest due to its high hydrothermal stability, its adsorption and diffusion properties for macromolecules, and its excellent selectivity and activity as a catalyst. In recent years, it has become a hot spot among research of porous catalytic materials and has been widely used in petroleum and natural gas processing, fine chemical processing, various adsorption and separation tasks, and other uses (Carvalho & Urquieta- Gonzalez, 2015; Teh, Triwahyono, Jalil, Mukti, Aziz, & Shishido, 2015)."

Jan 1, 2016

By A. Zarei-Hanzaki, S. M. Fatemi-Varzaneh, M. Haghshenas

The microstructure in modified semi-solid ALTHIX (A356) alloy consists of aAl phase with Al/Si eutectic structure. Silicon phase in eutectic structure is coral like with fine fibers. The lack of good ductility in this alloy is related to the presence of silicon fibers. Accordingly many investigations have been recently conducted to modify the Si morphology through Thermomechanical processing on this alloy. In the present work an ALTHIX (A356) alloy was deformed at 450°C, 500°C and 540°C through different strain rates. Consequently the silicon fibers were broken into small particles. The results indicated that the Si particles may coarsen according to Ostwald ripening mechanism at 540°C deformed by rate of0.0005 sec-1 & 0.0001 sec-1-

Jan 1, 2006

By F. E. Patton

"IntroductionAT NORANDA, the strength of the ore and wall-rocks per-mitted mining in large open stopes. While some of the orebodies were small and could be mined out in one stope, in most cases their size was such that it was essential that ore pillars be left during the first stage of mining. In these cases, backfilling has been necessary for ground control and to facilitate the later recovery of the ore in these pillars.This paper discusses the development of the •backfill and •its use in pillar recovery.GeologyThe ore bodies at Noranda occur as replacement deposits in a block of rhyolite flows and breccias, bounded on the north by the Horne Creek fault and on the south by the Noranda Andesite fault. Mineralization consists of pyrite, pyrrhotite, magnetite, chalcopyrite, sphalerite, gold, and various tellurides.The main orebody is a massive sulphide deposit designated the 'H' orebody. It is elliptical in plan, measuring roughly 400 feet by 800 feet, and is divided into two zones -Upper H, extending from surface to the 1,500-foot level, and Lower H, from the 1 ,500-foot level to just below the 3,000-foot level.Mining MethodsOpen stope mining in both Upper H and Lower H zones has been fully described in previous publications (1). A brief review only of the mining methods will be given here."

Jan 1, 1952

By Golaleh Riahi

An original method is used to obtain stable nanoparticles of gold-based mono- and bimetallic systems supported on an acidic zeolite. This approach has been applied to PtHY (1wt% Pt) and to bimetallic Pt-AuHY containing 1% of platinum to which is added the amount of gold required to give Au/Pt molar ratios of 20,40,60 and 80%. Metal clusters of Au or Pt-AuHY are formed inside the supercages of the zeolite framework by the thermal reduction of cations by the ligands (en = H2N-CH2-CH2-NH2) under inert gas flow at a temperature depending on the metal. The use of acidic zeolites favours the dispersion of the metal and the thermal stability of the particles. This stability is explained by chemical anchoring of metal clusters by the Brønsted sites of the support. Several techniques have proved that for a molar ratio of 20% metal particles of Pt-AuHY are bimetallic. The segregation of Pt and Au starts for molar ratio =?40%. The catalysts tested on the methylcyclopentane hydroconversion reaction reveal that the addition of gold to platinum leads to an increase in the activity and an improvement in the selectivity for isomerization of the skeleton (cyclohexane and benzene) to the detriment of hydrogenolysis. Similar results were obtained for the dodecane isomerisation to isododecane. These catalysts were also tested in CO, propene and propane oxidation. The activity of fresh catalysts is rather low. It increases after their pretreatment in oxygen or hydrogen atmosphere. In propene oxidation in the reaction mixture O2 ? H2, beside total oxidation of propene to CO2, also propene hydrogenation was observed, particularly at low temperatures. The presence of Au enhances the hydrogenation properties: high selectivities (> 90%) to propane and high propane yields on PtAu HY are observed up to ~150oC, whereas for Pt HY catalyst the selectivity and yield to C3H8 decreases rapidly with the temperature beginning from ~100oC.

Oct 1, 2003