Search Documents

By S. W. Asihene, K. Osseo-Asare

The thermodynamic data necessary for the quantitative treatment of Metal-NH3- H2O systems at elevated temperatures are lacking in the literature. As a result discussions of the chemical basis of high temperature processes, such as leaching and hydrogen reduction, have tended to rely on low temperature thermodynamic data. In this paper a critical review is presented of the available high temperature data for metal ammine formation in aqueous systems, and methods are suggested to enable extrapolation of elevated temperature stability constants from low temperature thermodynamic data. Predictions of the Van't Hoff Lsobar, the simple cation Correspondence Principle (whereby metal ammine complexes are treated as simple cations) and Helgeson's Electrostatic-Nonelectrostatic Model are compared with the available high temperature stability constants for nickel ammines. Up to 80 °C all three estimation methods yield results which are in agreement with experimental data. However, serious deviations occur at higher temperatures; the various models overestimate the stability constants in the order Van't Hoff Isobar > electrostatic-nonelectrostatic model > simple cation Correspondence Principle. Using the experimental nickel data as a basis, a method is presented which permits reasonable estimates to be made of the stability constants of metal ammine complexes for temperatures above 80 °C.

Jan 1, 2004

By W. Petruk

Mineralogical studies and concentration tests were conducted on samples from an oolitic iron deposit from the Peace River district in Alberta to determine what concentrate grades and metal recoveries could be obtained. The samples assayed 32 to 37 wt. % Fe, and consisted of goethite, nontronite, ferruginous opal, siderite , quartz, amorphous phosphate and illite . Flotation with fatty acids yielded the best over-all results. A flotation concentrate from a composite sample of the iron horizon assayed, by weight, 43.0% Fe, 12.3% SiO2 , 1.9% CaD, 0.9% MgO, 4.5% Al2O3 and 2.0% P2O5 and lost 17.2% on ignition, for an iron recovery of 48.8% and a silica rejection of 80%. When heated to drive off the water, the concentrate assayed 52 w t. % Fe and 14. 8% w t. % SiO2

Jan 1, 1977

By C. E. Baltzer

This paper highlights the position of coal supply in regard to the requirements for electric-utility operations. The text and the appended tables outline the trend of thermal power development and fuel use in the electric-utility industry. Mention is made of several argumentative factors influencing the use of coal in relation to competitive oil and gas, and of the importance attached to developing a realistic understanding of the respective problems faced by the supplier and consumer of coal. * * * TREND OF" THERMAL POWER DEVELOPMENT T HE RATE OF ADVANCE in thermal power has been significant during recent years, particularly in the Atlantic Provinces, the Prairie Provinces, Ontario, and British Columbia. While dependence on thermal power in Quebec and the Northern Territories is less than in the remainder of Canada, these regions also eventually will have need for increased amounts of such power.

Jan 1, 1961

By A. R. Farkoosh, K. Korgiopoulos, McGill University, O. Rodop, L. A. Villegas Armenta

"New generation of Al-Mg-Si alloys with thermally stable dispersoids that prevent recrystallization and grain growth during hot deformation are currently used in automotive components requiring good formability. Alloy chemistry controls the phase formation especially age-hardening precipitates, dispersoids, and primary intermetallic which have pronounced effect on grain structure, strength and formability. In this work, thermodynamic calculations have been used to predict the effects of varying levels of Si (0.5-1.5wt%), Mg (0.5-1.5wt%) and Mn (0.1-2.5wt%) on phase selection. Thermodynamic calculations have been performed in equilibrium and non-equilibrium conditions via the FactSage™ software using the FTlite database. Selected compositions have been cast, heat treated, extruded and characterized through scanning electron microscopy with energy dispersive spectroscopy and electron channeling contrast imaging techniques. The calculations showed that at the hot deformation temperature of ~540 oC, exceeding certain Mg and Si levels would lead to retained *-Mg2Si intermetallics and Si particles at the grain boundaries in addition to a-Al-(Mn,Fe)-Si. It was found that retained *-Mg2Si phase which adversely affects formability can be avoided for Si+2Mg levels lower than 2.3wt%. FactSage calculations also showed that increasing Mn from 0.5wt% to 1wt% leads to an increase in the amount of dispersoids (from 1wt% to 2wt%) that can potentially slow down recrystallization and grain growth during hot deformation and improve formability. Calculations at room temperature also show that for an alloy with 0.7wt% Mg, excess Si beyond 0.7 wt% promotes the precipitation of Si clusters in the Al matrix that accelerate natural age-hardening. Results were confirmed by experimental investigation.INTRODUCTIONAluminum alloy 6082 (Al-Mg-Si) is used in the automotive industry because of its high strength, and good weldability (I. J. Polmear, 2006). The alloy is age-hardenable through the precipitation of ß-Mg2Si and its precursors, and the recrystallization is usually inhibited by Mn- and Cr-containing dispersoids formed through high temperature heat treatments (I. Polmear & Couper, 1988). However, it is known that minor changes in alloy chemistry (Mg/Si ratio) can have significant influences on the ductility and formability of these alloys by altering phase selection and the resultant microstructure (Gupta, Lloyd, & Court, 2001; McQueen & Celliers, 1997; Zajac, Hutchinson, Johansson, & Gullman, 1994). For automotive applications where wrought alloys (usually extrusions) are cold-formed to produce suspension components, the chemistry of the alloys and the extruded structure are of crucial importance as they determine the formability at room temperature (Asensio-Lozano, Suárez-Peña, & Vander Voort, 2014). In this study, thermodynamic calculations along with experimental investigations were carried out on the Al-Mg-Si system to understand their phase formation and precipitation hardening as a function of alloy composition."

Jan 1, 2016

By D. H. Pulling

Statistics for copper consumption from various sources show that the importance of production from secondary sources is increasing. This is of particular significance in countries such as the U.K ., which are totally dependent on secondary material for the supply of home-produced copper . A brief survey of the U.K . industry has shown that, in the past, relatively high profit margins have not encouraged high cap ital investment and development of more sophisticated operating techniques, but set against a background of rapidly escalating operating and energy costs , together with an ever-increasing demand for copper , it is anticipated that the industry will see great changes in the near future. With this in mind, an experimental furnace for continuous smelting of copper-bearing scrap has been developed at the University of Birmingham. This furnace has been designed to combine the conventional operations of blast furnace or reverberatory smelting, usually followed by converting, in one unit, and incorporates many of the features of the WORGRA and Noranda processes for continuous primary smelting . It consists of a long, sloping channel, constructed of chrome-magnesite refractory, which: is churned near the top. Smelting is effected lower down the channel, where iron, etc., in the scrap is oxidized and slagged off with silica flux. Provision is made for oil injection to increase oxidation rates. Metal can flow from the bottom of the channel, and slag from the top, so that a counter-current flow is achieved. The approximate molten capacity is 25 kg. Various scrap charges, both synthetically made and as supplied from various industrial smelters, have been successfully smelted. Metal of 83 -95 % Cu has been produced, depending on the original charge composition and the degree of air injection, although air injection was also found to considerably increase the copper loss to slag. Recoveries of other valuable non-ferrous metals in the charge were good.

Jan 1, 1977

By T. Plikas, L. Gunnewiek

Computational fluid dynamics (CFD) modeling was used to evaluate the performance and optimize the design of a potroom ventilation system in an aluminium smelter facility. The ventilation system must ensure the inflow of fresh air to the workplace by natural draft and the removal of heat and hazardous emissions generated from the pot cell process. A full-scale, three dimensional CFD model of the potroom was developed to predict the air temperature distribution and contaminant concentrations throughout the potroom for the purpose of verifying that the industrial workplace hygiene standards will be met by the proposed ventilation system design. The modeling work was used to optimize the size of the floor gratings around the pot cell and roof ventilator, as well as determine damper settings in the roof ventilator. The effects of outside air temperature and external wind on the performance of the ventilation system was evaluated to ensure the design performs adequately in response to seasonal variations in climatological conditions.

Jan 1, 2006

By Réal Tanguay, Mathieu Piché, Jacques Carignan, Charles Beaudry, André Bonenfant

"Le gisement Isle-Dieu est situé sur le flanc sud de l'anticlinal de Galinée. La stratigraphie locale comprend, de bas en haut, la rhyolite du Groupe du Lac Watson surmontée par le basalte du Groupe de Wabassee. Un horizon repère, siliceux et sulfure, d'origine sédimentaire, appelé ""Tuffite Clef', est présent au sommet du Groupe du Lac Watson et pend à 45° vers le sud.Le gisement Isle-Dieu est constitué par une lentille qui recoupe, en partie, la ""Tuffite Clef"". Elle est séparée en deux trorçons par un dyke de tonalite. Les données obtenues à partir des forages effectues à travers la rhyolite sous-jacente permettent de définir les zonations chimiques et pétrographiques de la cheminée d’altération.Ces transformation minéralogiques et chimiques sont caractérisées par un enrichissement en MgO, Fe2O3, MnO et un appauvrissement en CaO, SiO2 et Na2O. La zonation spatiale de ces altérations permet de mettre en évidence la géométrie et l'extension des conduits hydrothermaux. L'épaisseur maximale des sulfures massifs au sein de la lentille est en étroite relation avec l’importance des zones d'altération. Les patrons de variations chimiques dénotent une orientation préférentielle WNW des conduits hydrothermaux. Les parties les plus altérées et les plus déformées présentent localement de fortes variations positives en Zr, Nb, et terres-rares; ces concentrations sont vraisemblablement imputables a /' enrichissement résultant de la diminution du volume lors de l'altération.L'étude pétrographique montre que la porosité et la perméabilité du milieu ont joué un rôle important dans la circulation des fluides car les roches de la cheminée présentent des phénomènes de dévitrification, de bréchification et de microfracturation très prononces. La nature magnésienne de certaines chlorites et la perméabilité accrue du milieu semblent en accord avec le modelé propose par Roberts et Reardon, ( 1978 )"

Jan 1, 1990

By Jaeheon Lee, Junmo Ahn, Isabel F. Barton

"Newmont’s Mike prospect, currently undeveloped, is a blind Cu-Au(-Zn) deposit on the Carlin Trend, containing >8.5 M oz. Au, 1027 M lbs. Cu, and 809 M lbs. Zn as Carlin-type gold and polymetallic Cu-Zn minerals in Paleozoic lower-plate carbonates and shales. This project was undertaken 1) to examine the effectiveness of different lixiviants for leaching the Mike supergene Cu-Au ores via bottle roll tests, and 2) to determine what ore minerals resist dissolution in each leaching agent by comparing the mineralogy and chemistry of head and tail samples. Sulfuric and sulfurous acids were used to leach copper and cyanide was used to leach gold. Thiourea, glycine, and other lixiviants were used to leach both base metals and precious metal. QEMSCAN and SEM study of six samples of different ore types and grades indicate that the Au occurs as varieties of native gold, including auricupride and electrum. Major Cu minerals are native Cu, cuprite, malachite, chrysocolla, and conichalcite (Ca-Cu arsenate), with locally significant Cu in jarosite and goethite. Gangue mineralogy is dominated by quartz, sericite, chlorite, alunite, smectite and kaolinite, K-feldspar, and iron oxides (sensu lato). Results of bottle roll tests and leach residue mineralogy will be presented and discussed at the conference.INTRODUCTION Resource and Geologic Setting The Mike deposit is a large, blind Cu-Au(-Zn) deposit in the Maggie Creek district of the Carlin Trend of Nevada, USA, near the Gold Quarry mine (Figure 1). The mineral inventory, based on drilling, is 8.568 Moz. Au, 1027 M lbs. Cu, and 809 M lbs. Zn at average grades of 0.72 g/t Au, 0.34 wt% Cu, and 2.13 wt% Zn (inventory for a cone at $400/oz Au and $0.80/lb Cu by Norby and Orobona, 2002)."

Jan 1, 2017

Up to thirty years ago, coal preparation in western Canada, except at four plants, had not included actual coal washing. The exceptions were at Nanaimo and Royston, B.C., where tub washers and wet tables were in use; at Hosmer, B.C., using. Robinson cones; and at Leitch Collieries, Passburg, Alta., using a feldspar jig. The two last named collieries had a short life and were not operating in 1920. The industry was divided, as at the present day, into two sections, steam (bituminous) coal and domestic (largely sub-bituminous) coal, the first generally supplying industrial needs and the second householcl and other heating requirements. The two sections overlap to some small degree today as prepared sizes, chiefly stoker, and briquettes, from steam coal are shipped for house-hold use, and domestic slacks are used in certain industrial plants. The .domestic operator, for reasons shown later, was not primarily concerned with actual coal washing as a phase of coal preparation, and bent his efforts to improvement of screening and loading plants, with hand-picking of coarse sizes. The bituminous operator, on the other hand, felt it necessary by 1920 to consider coal washing. When the mines were comparatively young, coal quality could be controlled to a considerable degree by selective mining, by leaving behind some of the seam or by-passing districts in a mine where the coal was of inferior quality to that in other districts. This obviously had its limitations, and so the next step was coal washing.

Jan 1, 1952

By Steven D. Botts

The Antamina project, owned by BHP Billiton Plc, Mitsubishi Corporation, Noranda Inc., and Teck Cominco Ltd. , is a $2.3 billion copper/zinc project, located in the Ancash Department in Perú. The project consists of an open pit mine, a 70,000 ton per day concentrator, a 302 Km. long concentrate pipeline, port facilities, a new access road, power line, and town site. The project is designed to produce up to 1.5 million tonnes per year of copper and zinc concentrates over a 23-year project life, and will be the third largest producer of zinc and the seventh largest producer of copper in the world. This mega project is the largest mining investment in the country and, during its construction stage, was the most important construction project worldwide. On May 28th, 2001, Antamina commenced testing operations and four months later, it reached commercial production. Antamina was officially inaugurated on November 14th, 2001 by Peruvian president Alejandro Toledo. The construction stage of the project generated 8,000 direct jobs, with a peak of 10,000 employees, and 30,000 indirect jobs. The permanent workforce consists of approximately 1650 employees, the vast majority of which are Peruvian Nationals; around 30% of whom came from the department of Ancash where the deposit is located. Approximately 5,800 indirect jobs will be generated from the project. Independent sources state that Antamina will increase the Peruvian mining exports by 30% and Peruvian GDP by 1.4% within its first year of full operation in 2002. Since winning the privatization bid for the project in 1996, the company has implemented a successful approach to community development and environmental protection based on sustainable development principals. Throughout the development of the project, a number of initiatives have been undertaken to ensure full involvement of the local populations in community development activities and the company?s environmental program. Due to its size, difficult logistics, cultural considerations and financial aspects, the project has faced a number of unique challenges in the area of environmental protection and management of community interaction. Antamina has been innovative in its approach to these issues, and as a result, has set new standards in Perú for environmental and community management, and sustainable development.

May 1, 2002

By Y. Huang

Corrosion of GaAs in aqueous electrolytes is a major limitation in implementing GaAs-based photoelectrochemical solar energy conversion systems, In this work, the corrosion behavior was investigated by electrochemical methods and surface analysis approaches, in both H2SO4 and NH3?H2O solutions, Open-circuit measurements showed that the cleaned GaAs surface was very sensitive to water/air, Impedance measurements for n-GaAs showed that an inductive loop only appeared at a high corrosion rate because a reaction intermediate is the oxidant for a further decomposition step in combination with chemical reaction with water, The results suggest that the same corrosion/decomposition mechanism occurred on n-GaAs in the two solutions, When the surface-hole concentration was low, the hole injection or generation process was the rate-determining step, At large reverse bias on n-GaAs, with high-hole concentration, the corrosion rate was limited by a Faradaic adsorption process, involving an adsorbed intermediate, The different surface compositions after corrosion in the two solutions can be explained by the dissolution of As(0), Further oxidation of As(0) to As(III) in NH3?H2O solution is still slow, as suggested from X-ray photoelectron spectroscopy (XPS) analysis,

Jan 1, 2005

By Zhan Zhang, Hiromi Nagaumi, Zhen Li

"Recently, the remarkable strengthening effect of ??-Al(Mn, Fe) Si dispersoids at both ambient temperature and elevated temperature were found by several researches. A large amount of dispersoids can be formed by applying special heat treatments and within a suitable range of chemical composition of AA3xxx alloys. In the present work, the influences of Cr addition on the mechanical properties and microstructures of the Al-Mn-Mg-Si alloys were investigated. The mechanical properties at ambient and elevated temperatures were evaluated by micro-hardness and yield strength. Moreover, the microstructures in as-cast and heat-treated conditions were quantitatively analyzed by optical and electron microscopes. Results revealed that Cr also had effect on the number density and volume fraction of dispersoids. Micro-hardness and yield strength at ambient temperature increased with the increasing content of Cr, and the Cr addition increased the yield strength at elevated temperature as well. Moreover, the creep resistance at 300°C improved dramatically with the increasing content of Cr.INTRODUCTION Traditionally, AA3xxx aluminum alloys were widely used in packaging, automobile and architecture industries, because of its good formability, excellent corrosion resistance and weldability. And AA3xxx alloys were considered as non-heat-treatable alloys. However, the strengthening effect of dispersoids in AA3xxx alloys was discovered recently (Li & Arnberg, 2003;Li, Muggerud, Olsen, & Furu, 2012; Li, Zhang, & Chen, 2016; Liu & Chen, 2015).Alarge amount of dispersoids could precipitate by a proper heat treatment.In order to further improve AA3xxxalloys, the composition of the alloys should be optimized. A few previous studies were reported to investigate the influence of compositions on AA3xxx alloys. Adding Mn element could enhance the precipitation of ??-Al(Mn, Fe)Si dispersoids and improve the yield strength(Muggerud, Mørtsell, Li, & Holmestad, 2013), as long as the concentration of Mn was under the solid solution limit. Fe decreased the solubility of Mn and accelerated the precipitation rate of ??-Al(Mn, Fe)Sidispersoids(Li & Arnberg, 2003), the yield strength and creep resistance at elevated temperature could increase with an optimized content of Fe(Liu & Chen, 2016). Mg element would affect the nucleation process of ??-Al(Mn, Fe)Sidispersoids by forming metastable Mg2Si(Hirasawa, 1975; Li, Zhang, & Chen, 2017a; Lodgaard & Ryum, 2000), metastable Mg2Si precipitated during heating process and promoted the precipitation of ??-Al(Mn, Fe)Sidispersoids, moreover, Mg provided solid solution strength for AA3004 alloys(Li et al., 2016). Si increased the volume fractionof ??-Al(Mn, Fe)Sidispersoids(Muggerud et al., 2013)and decreased the size of ??-Al(Mn, Fe)Sidispersoids(Li, Zhang, & Chen, 2017b). With the addition of Mo, the size of dispersoids became finer with a higher volume fraction, the volume percentage of dispersoid free zones was reduced. Elevated temperature yield strength and creep resistance improved due to Mo addition (Liu, Ma, & Chen, 2017).However, the effect of Crelements on microstructure and mechanical properties of AA3xxx alloys were rarely reported."

Jan 1, 2018

By Floyd Smith

Based on underground observations made in .the coal mines of the Dominion Coal Company Ltd., this paper deals with the stress phenomena in the approach roads and headways and in the gob areas associated with the longwall method of total extraction. The deformation of roadways during development and the deformation of roadways during the total extraction period is delineated and presented in graphical form .. Conclusions are made as to the feasibility of the introduction of the retreat method of longwall extraction in one of the colhenes. The importance of future studies are enumerated, especially. those pertaining to the determination .of the opti.m.um sizes of protective pillars and to increasing the efficiency of the current methods of artificial roadway support.

Jan 1, 1967

By J. P. Morgan, D. B. Stewart

"AbstractLoad-haul-dump machines equipped with. a torque converter and hydraulic pumps have been field tested by means of an engine monitoring instrumentation package. It was found that owing to parasitic losses in the ancillaries and drivetrain, maximum available useable pourer may peak at less than full engine speed. Simple reduction of engine speed may save 15 to 25 percent on fuel consumption, with no significant loss of available power. On some machines, speed reduction will require modification of the torque converter . The cost of this modification, when necessary , would be offset by reductions in exhaust emissions, ventilation requirements, fuel consumption , heat, noise and hydraulic system maintenance, and by increased life of rotating components and filters and machine availability.IntroductionTHE CANADIAN EXPLOSIVES ATMOSPHERES LABORATORY, in conjunction with Deutz Canada Limited, has designed, constructed and field tested a portable instrumentation package. This package monitors diesel engine performance in underground mining machinery by continuously recording engine speed and volumetric fuel delivery. During tests designed to determine the engine load and speed conditions for the various segments which constitute actual underground operation of a Deutz F6L 714-powered 4-yard load-haul-dump machine, it was discovered that an unexpectedly large percentage of the engine power was required to overcome the ancillaries and drivetrain drag (1). That this large component of engine power is functionally related to engine speed rather than the operator's needs was verified by repeat tests of the used 4-yard machine and by testing of a new 5-yard machine powered by a Deutz F 8L 714."

Jan 1, 1977

By Sangjian Zhang, Zhu Xiao, Lairong Xiao, Rushi Chen, Mei Fang, Zhou Li

The copper-graphite metal matrix composites were fabricated by two different production methods: directly sintering with copper and graphite (Cu-Gr composite), and in-situ sintering with cuprous copper and graphite (Cu2O-Gr composite). During the in-situ reaction sintering, a redox reaction occurs at the interface of the Cu2O particles and Gr particles, resulting in the improved physical and mechanical properties of Cu2O-Gr composites. Compared with Cu-Gr composite, Cu2O-Gr composite has a higher compression strength at any given graphite content due to the improved interface bonding and uniformly distributed fine graphite particles in the matrix. Increasing graphite content decreases the mechanical properties of the copper-graphite composites. The compression strength of Cu2O-Gr composite is 50-100 MPa higher than that of Cu-Gr composite. INTRODUCTION Copper-graphite composites have been widely used in industry due to their low density, relatively high strength and hardness, good thermal and electrical conductivity, arc ablation resistance and self- lubrication ability (Grandin & Wiklund, 2018; Han & Xu, 1999; Huang et al., 2017). Electric sliding contact friction pair in the high-speed railway system and motor brush in electric contact components have a very high demand on electrical conductivity and self-lubrication ability of materials. The electric devices need to bear both mechanical load and high electric current. Copper-graphite composites with good mechanical, electric and self-lubrication properties are the best candidates for application in multifunctional electric sliding contact frication components. The relative sliding speed of friction pair is developing towards 100 m/s or even faster, which can withstand the electric flow of more than 800 A, and it is often accompanied with vibration and impact (Guo & Ding, 2008). Conventional wear-resistant materials can no longer meet the current requirements and this promotes the development of copper- graphite composites with excellent comprehensive properties (Ding, Chen, Zhu, Zhang, & Zhou, 2009; Yasar, Canakci, & Arslan, 2007). There are many ways to fabricate copper-graphite composites, mainly including powder metallurgy method, liquid immersion infiltration method, rapid sintering method and electrodeposition method (Kalin & Poljanec, 2018; Kim, Lee, & Han, 2014; Liu et al., 2018; Wang et al., 2018). Each method has its own advantages and disadvantages, and the powder metallurgy method is the most commonly used one due to its simple process, high economic benefit, and industrial production applicability. The common steps of the powder metallurgy method are as follows (Samal, Parihar, & Chaira, 2013): firstly mixing the copper (copper alloy) powders and graphite with a certain ratio, following by die-forming, and then sintering at the high temperature with or without pressure. The advantage of copper-graphite composites is that the graphite distributed in the copper matrix uniformly and it can form a carbon diaphragm preventing the wear of the composite (Fu & He, 2010). However, the bonding strength of the interface between the copper matrix and the graphite is relative low as the combination between them is mechanical interlocking but not metallurgical bonding (Ma et al., 2008). It is meaningful to develop new fabrication technology of copper-graphite composites with better interface bonding, which could provide guidance for the design of copper-graphite composites with excellent comprehensive properties.

Jan 1, 2019

By H. R. Banks

IF you have ever travelled in the valley lying between the Selkirks and the Rockies in the East Koorenay district, you will have noted that the former mountains are rounded and massive, while the serrated peaks of the latter, fingering into the sky, bring an entirely different. picture. These two mountain ranges, with the comparatively level valley between, serve splendidly to introduce the subject for discussion. It is rather strange that, despite the fact that wear is undoubredly the greatest force with which human ingenuity bas to contend, it has come in for very little study from the stand point of pure science. Empiricism has been the sole ally in the fight for improvement! That we may have a clear understanding as to what we mean by wear, I would include in the term the breaking dawn of ail solid matter, from the natural wearing dawn of the mountains previously mentioned, to the hale in the mill pipe-line, which forces one to shut-down-usually at some un-earthly hour-to carry out a repair. It seems a far cry from mountains to mill launders or pipe-lines, but, magnified sufficiently, most of the materials with which we have to deal would show surfaces not unlike those we see around us. The progressive steps of wear, or ?erosion' as our geological friends would prefer to term it, are exemplified in the two ranges of mountains and the valley between. True, the wearing dawn by natural forces is a slow process. The aeons which have passed since first these mountains were formed seem endless. The natural forces pitted against them seem puny in the light of the interminable rime that has been needed to effect the changes. But here, as in the case of the materials with which we are dealing day by day, the combination of many forces ultimately brings about that condition which we describe as 'worn out'. In the case of the mountains, it is when they are finally levelled into plains, and in the case of equipment which we use, it is when that equipment will no longer serve its purpose.

Jan 1, 1943

By N. W. Bliss

"Bauxite has been the almost universal ore of aluminum for about 100 years, with most of the world's reserves oc¬curring in the developing countries. As a result of fiscal and political activities prompted in part by the energy crisis, the formation of the IBA combined with increasing freight and labour costs, these reserves are no longer as competitive or as secure as they once were. This has given fresh impetus to the development of processes for alumina production that utilize raw material other than bauxite. Canada has no bauxite and it is prudent to look for alter¬native raw materials within our own boundaries suitable for one of these processes.Of the three igneous rocks that have been used as a source of alumina, only anorthosite is considered as a potential source in Canada. The Al content would be extracted by a sinter process, which currently requires a raw material with a. minimum of 28% Al2O2. Thus, about 4 tons of anorthosite and 10 to 12 tons of limestone are needed to produce one ton of alumina. There are two petrologically distinct types of anorthosite, one containing the plagioclase andesine-labradorite and around 26% Al2O3, and the other containing upwards of 30% Al2O3, in by¬townite-anorthite; for our purposes they may be con¬sidered as low- and high-alumina anorthosite respectively. The high-alumina anorthosites are somewhat rare; the low-alumina anorthosites are much more common, partic¬ularly in Eastern Canada. Geologically speaking, there is no shortage of anorthosite in Canada. The reserves are im¬mense, although their low Al2O3 content coupled with con¬siderations of location, access and proximity to limestone could be constraints to their development. Fly ash from coal-fired thermal power stations and nepheline syenite can also be used in a sinter process, but neither is likely to be utilized in Canada in the immediate future.The H+ process utilizes an acid attack to leach Al from a raw material with at least 20% Al2O3. One of the best raw materials is kaolinite-bearing clay; not only is it high in Al, but most of it can be extracted. With the possible exception of the Whitemud clay in Saskatchewan, Canada is apparently deficient in clays with sufficient reserves to support an alumina plant utilizing the H+ process. Low-alumina clays with illite and montmorillonite may also prove to be a suitable raw material if advantageously sited with respect to industrial centers. The average shale con¬tains only 15% Al2O33, much of which may be contained in minerals, such as feldspar, not amenable to acid leaching. If shale is used as a source of alumina, it will be because it contains some other valuable commodity, such as oil or uranium, the extraction of which leaves the spent shale upgraded in extractable Al2O3 and lowers the over-all costs to a point where it is economic, Thus, rejects from coal washing plants are most commonly considered as a source of alumina; they are already mined, are available in large and ever increasing amounts, and may contain significant amounts of combustible material which upgrades the Al2O3, content of the resulting ash. Coal rejects from existing and developing coalfields in Alberta and British Columbia are a possible source of raw material, but present data indicate they may contain insufficient Al2O3."

Jan 1, 1976

By Thomas Genty, Pascal Marcotte, Matthew Gillman, John Baechler

Elevated concentrations of ammonia nitrogen is a common characteristic of mine impacted water and generally results from the dissolution of undetonated explosives (i.e., Ammonium Nitrate and Fuel Oil and emulsion explosives) by contact water. Several active water treatment technologies are commercially available to remove ammonia nitrogen, but reduction of active treatment demand by promoting natural attenuation is considered best industry practice. In this paper, the results of laboratory-scale and full-scale trials of a semi-passive approach (i.e., enhanced algae growth) to remove ammonia nitrogen at the Meliadine mine are presented. Phosphorus was found to be the limiting factor to algae growth at the mine site. The addition of various concentrations of phosphorus was first tested at a laboratory scale. The samples were exposed to in-situ conditions, and ammonia nitrogen removal rates ranging from 40% to 93% were achieved over a period of 24 days. This paper also presents the methodology and results of an in-pond treatment during which a 50% ammonia nitrogen removal rate was observed after 68 days. The studied mine site uses breakpoint chlorination as its primary treatment approach for ammonia nitrogen removal. The results presented in this paper show the potential of using enhanced algae growth as a pre-treatment method, subsequently reducing the quantity of chemicals required for operating the breakpoint chlorination plant. This potential requires further investigation and additional trials are currently under evaluation.

Jan 1, 2023

By G. A. Van Wielingen

"The conditioning of natural gas to meet contract pipeline specifications involves in the majority of cases in Western Canada, the appropriation of substantial capital expenditures for treating and processing installations. It is therefore of vital importance to the owners and producers of natural gas to arrive at an appreciation of the economics pertaining to the production and surface handling of their gas reserves at the earliest possible stage of field development. The treating and processing of natural gas often results in considerable changes in composition and related physical characteristics between the wellhead and the point of delivery of the saleable gas. This paper presents a general outline of engineering calculations which can be applied in the pre-determination of the effects that surface handling of gas will have on the composition and physical characteristics of sale-able gas. Emphasis has been placed on the calculation of hydrocarbon dew-points, heating values and shrinkages prevailing at the various stages in the surface handling of natural gas. It is believed that advance information indicating the approximate ranges of these physical properties will facilitate process selection and will provide a basis for the estimation of capital and operating costs of process installations."

Jan 1, 1960

By Rosie Moore, Harvey Keats, Kerry Sparkes, A. J. Naldrett

"Abstract-The Voisey’s Bay Ni-Cu-Co deposit was discovered in late 1994 as the result of prospecting initiated in the summer of 1993. By July 1995, proven mineable reserves were 31.7 x 106 tonnes grading 2.83% Ni, 1.68% Cu and 0.12% Co, and current total resources in all categories are quoted to be in the order of 150 X 106 tonnes. The deposit is associated with a body of troctolite belonging to the Nain Anorthosite (1.35 Ga - 1.29 Ga) suite, which was emplaced across the boundary between the Proterozoic "Rae" Province to the west and Archean "Nain" Province to the east.The deposit can be described in terms of three geological settings. The "Ovoid" is a 600 m long by 350 m wide by 100 m deep lens of massive sulfide, covered by 10 m to 20 m of glacial overburden, and separated from the underlying country rock quartz-plagioclase-biotite gneiss by a breccia of gneissic fragments in troctolite known as the Basal Breccia Sequence. To the west of the Ovoid lies the "Western Extension", comprising disseminated and massive sulfides in a north-dipping sheet of troctolite which ranges from upper unmineralized troctolite down through troctolite with increasing amounts of sulfide (up to 50%), to massive sulfide (in some places only), and then to Basal Breccia Sequence. East of the Ovoid, the troctolite sheet broadens out into a troctolite intrusion, within which occurs the "Eastern Deeps", a zone of massive and disseminated sulfide up to 100 m thick that is currently being explored. The mineralization of the Eastern Deeps lies along the line of intersection of a feeder sheet with the base of the intrusion. The current interpretation is that the three geological environments represent different erosional levels through a single mineralized intrusion. In this model, the deepest erosional level lies to the west and exposes the feeder to surface, whereas the Ovoid represents the base of the intrusion at surface, and the Eastern Deeps the base of the intrusion overlain by 600 m to 900 m of troctolite. Sulfides and gneissic fragments were brought up by magma flowing quickly through the feeder, and settled out where the flow rate decreased as the sulfide-bearing magma mixed with magma already emplaced in the intrusive body."

Jan 1, 1996