Search Documents

By Rais SA

In June, 1986, Freeport Indonesia, Inc., in conjunction with Out- okumpu USA, laboratory tested the Flash flotation concept on Primary ball mill underflow. These laboratory results indicated a possible 10% increase in precious metal recovery and 0.6% increase in copper recov- ery were available over conventional methods. By October of the same year two Outokumpu Skim Air SK-240 units were operational on one mill circuit and were achieving 5 to 10% increased recovery in precious metals with equal copper recovery at one percent higher final concentrate grade. Two more cells were purchased and installed on the remaining grinding circuit in July, 1987. As part of the installation of the Skim Air cells, an existing cluster of six 508mm Krebs cyclones were replaced by four 660mm Krebs cyclones. To reduce high circulating loads, these new cyclones were made horizontal at 45 degrees. This arrangement succeeded in reducing the mill circulat- ing load by 100% and has allowed for a 10% increase in throughput at the same grind.

Jan 1, 1988

By Gardavsky V, Gabell AR, Green AA

The I,)hyllosilicate mineral chlorite is a common constituent of altered rocks associated with volcanogenic massive sulphide deposits, and literature studies indicate that, in general, this mineral is progressively enriched in magnesium relative to iron as an orebody is approached. Studies have shown that there is a direct correlation between the Mg/Mg + Fe ratio of chlorite and its absorption spectra in the 2.7 to 3.0 um range. However, this region, which contains the fundamental 0-H stretch absorption features, is affected by intense atmospheric absorption, and therefore cannot be used for remote sensing. At shorter wavelengths (0.4 - 2.5um), there are windows where the atmosphere is sufficiently transparent and vibrational absorption bands still occur, although they are clue to overtones and combinations, and accord- ingly are much weaker than the fundamental features. Shifts to longer wavelengths with increasing iron content can still be observed in this region of the spectrum and, with better spectral resolution and sensitivity, it may be possible to monitor subtle variations in chlorite chemist by remote sensing techniques.

Jan 1, 1987

By Quilliam B, Richmond G

Aberfoyle Ltd. has utilised a variety of flotation technologies in the Hellyer concentrator in North-Western Tasmania. Hellyer ore, with its slow flotation rates and low rate differentials between values and gangue, requires the use of long residence times and low air consumption rates in the flotation circuit. The operation of the flotation circuit, with a nominal residence time of 7 hours, has necessitated the development of a control system to provide continuity through operator shift changes. Cell selections at Hellyer varied from the 54 m3 hybrid Dorf Oliver / Maxwell (DO/MX) cells, to smaller 32 m3 Maxwell cells, conventional Don-Oliver 300 (8.5 m3) and 600 (17 m3) trough cells, and a column cell. The advantages of the large cells included low specific power consumptions and a low capital cost. However, problems with mixing and the maintenance of consistent froth depth have been identified in the hybrid DO/MX cells. Short circuiting in the trough cells was apparent, causing a considerable reduction in metallurgical performance. The column cell performs to expectation, although the application is not ideal.

Jan 1, 1991

By West-Sells P, King J. A, Patel C

The Eskay Creek orebody is located in north-central British Columbia (Canada). The ore contains major gold and silver values and minor but economically significant quantities of zinc. The refractory nature of the gold necessitates a pressure oxidation pretreatment prior to cyanidation. After solid-liquid separation the oxidation solution can be treated by oxyhydrolysis for iron removal and cementation with zinc dust for noble element removal. The resulting solution, as obtained in pilot studies, contains 7 - 10 g/L Zn, 0.5 g/L Ca and 2 - 4 g/L Mg. Minor amounts of cadmium, copper and iron may also be present in the solution. Over 90 per cent recovery of zinc from Eskay Creek oxidation solutions could be obtained by four stages of zinc extraction with Cyanex 302 extractant (Cyanamid Canada Inc, Niagara Falls, Canada). Zinc was stripped from the organic with spent zinc electrolyte in two stages. A complete description of the bench scale and miniplant studies of the solvent-extraction electrowinning circuit follows. The behaviour of minor amounts of copper, cadmium and iron in the circuit is also Discussed.

Jan 1, 1993

By G J. Sparrow, M J. Fisher-White

A mineral and chemical characterisation study was conducted on ilmenite-rich heavy mineral concentrates sourced from the western sector of the Eucla Basin in southern Australia. Test work involved using X-ray diffraction (XRD), scanning electron microscope (SEM) and electron microprobe-based characterisation methods. Results showed considerable variability in the degree of ilmenite alteration between deposits with TiO2 contents varying from 53 - 63 wt per cent TiO2. Notwithstanding variability between individual deposits, the samples all had [Ti]/[Ti+Fe] ratios >0.5 consistent with a mineral assemblage of hydrated ilmenite or the hydrated, Ti-rich alteration phase pseudorutile (Fe3+2-x Ti3O9-3x (OH)3x). Accessory phases consisted of rutile (primary and secondary), zircon, aluminosilicates, quartz, Fe oxyhydroxides and spinels. Results for the most altered material are broadly comparable with data for ilmenite concentrates from the eastern margin of the basin. The mineralogy of the western Eucla Basin concentrates and the minor element composition of the ilmenite grains suggest they could be upgraded to synthetic rutile by a modified Becher process.

Jan 1, 2008

By W J

Al ores arriving at the works which contain more than 3% sulphur, together with all sands and other fine residues, are delivered to the roasting department. Those that are in a coarse condition are first sent to the crushing plant, consisting of 15 in. x 9 in. jaw crushers and two No. 5 Krupp mills. The ore is here crushed through a quarter mesh screen. Any pyritic concentrates high in sulphur are given a preliminary roasting, to bring the sulphur contents down to about 12 % and the roasted material is delivered to the H. H. charge-making bins. Here the various ores, sands, residues, roasted pyrites, together with about 12 % of limestone, are made up into I-ton charges in hopper trucks with bottom discharge. The trucks are elevated by hydraulic lifts to a tramway running over the roasting furnaces, and the contents are dropped into hoppers over each furnace, from whence the mixture is fed into the centre of each furnace by means of a Challenge ore-feeder.

Jan 1, 1918

Blasting effectiveness must be gauged by total production costs. ANFO charges made up in polythene "sausages" are not as profitable as is indicated by the price of ANFO. All-slurry charges are warranted only where blastholes cannot be dewatered effectively, or where drilling costs are very high. An increase in blasthole diameter leads to coarser fragmentation. This effect is most pronounced in tough and massive or blocky strata, or in ground which consists of unfissured boulders in a softer matrix. When ANFO and some slurry-type charges of small diameter are used in plastic-acting ground, charges may fail to detonate through precompression by charges fired on an earlier delay. The optimum blasthole length is rarely less than four times the burden distance. For best results, blastholes should be inclined to the vertical and parallel to the face. Nominal burdens and spacings are often altered radically by the initiation sequence. For best fragmentation, all blastholes must have good effective faces, and should be effectively stagg- ered with an actual spacing:burden ratio in the approximate range 2.0-5.0.

Jan 1, 1975

By Tullemans FJ

This paper describes the general approach to ore reserve estimation and mine planning used at the Kidston Gold Mine. The geological setting and exploration is briefly summarized for background information.A geostatistical study of the deposit was carried out to determine the geological ore reserve. This was confirmed using a manual polygonal technique. Optimum pits outlined by a Lerchs-Grossman open pit design algorithm were manually smoothed allowing mineable reserves to be calculated. Mine production schedules based on kriged block grades and tonnages are continuously updated using production blasthole assays. An arithmetic mean technique of block grade estimation has proved successful to date. After milling approximately 4.9Mt of ore, the mill grade of 2.13g Au/t is only 0.5% above the mine estimate of 2.12g Au/t. The difference in contained gold between "As staked" blasthole reserves and kriged mineable reserves is 3.8%. The application of blasthole kriging as a basis for ore/waste classification in erratically mineralized areas is being evaluated. Planned future developments are briefly mentioned.

Jan 1, 1986

The Central Extended Orebody is located within the Cracow Goldfield approximately 360 km northwest of Brisbane and approximately 220 km west of Bundaberg. It is an epithermal gold deposit hosted by the Late Carboniferous to Early Permian Camboon Andesite. The lode was mined by open cut methods and produced 170 458 tonnes of ore at 5.62 g/t gold.The geology of the rit is relatively simple, comprising two rock types, trachyandesite and rhyolite which have been sub-divided into several units. The trachyandesite is sub-divided into three rock types: brecciated trachyandesite which is the most widespread, hydraulically fractured trachyandesite hosts the mineralisation and the third sub-unit is chloritised hydraulically fractured trachyandesite and has no associated mineralisation. The mineralisation is confined to quartz veins in hydraulically fractured trachyandesite. Several phases of brecciation and subsequent quartz and quartz/adularia vein injection are evident although not all phases are mineralised. Two rhyolite dykes intrude the trachyandesite one is monolithic, the other is sub-divided into hydraulically fractured rhyolite (barren), silicified rhyolite and auto-brecciated rhyolite.

Jan 1, 1993

By S Moradi

The thickener overflow of zinc concentrate, obtained from flotation process in the Angouran plant located in Iran, contains a large quantity of slimes which were transferred to the tailing ponds. These slimes have caused problems of storing and environmental aspects in the Angouran area. The objective of this research is to describe the extraction of zinc from these slimes by leaching method using sulfuric acid in pilot plant scale.Chemical analyses showed that these tailing materials contain 35 per cent of zinc. By XRD analysis, smithsonite is identified as the major constituent. Calcite, dolomite, and cerussite are found as carbonate minerals. A minimal amount of Zn occurs as hemimorphite. Quartz, kaolinite, clinochlore and muscovite are other silicate minerals in the slimes.In the optimal conditions, ie acid leach at pH of 1, temperature of 55¦C, reaction time of 120 minutes and solid-liquid ratio of 1:3 and neutralisation with Ca(OH)2 at pH = 4.5, temperature = 70¦C, time = 90 minutes, the total recovery of zinc obtained was 95 per cent.

Jan 1, 2004

Compared with modern longwall coal mining systems, automation has not been developed very far in the underground metal minin industry. One of the main reasons for this is that present har rock mining systems do not produce ore with a controlled degre of fragmentation. The often poor fragmentation from the stopescauses large extra costs and precludes material which 1-ends itself to automationThe paper investigates the possibility c technology for automatic loading and trapconveyor belt to a shaft dump pocket. With this concept, it will be necessary to control the maximum fragment size by careful blasting design. The degree of fragmentation will have to be finer than is common to-day. The study shows that the belt conveyor mining con-cept with controlled fragmentation may be economically competitive with conventional cyclic loading and transport, even for an annual production as low as 0.5 mill. tonnes.. Fragmentation design and cost calculations have been based on a combination of the Kuznetsov relationship between blasting parameters and mean frag-ment size, and the Rosin-Rammler formula for fragment size distribution.

Jan 1, 1985

By J M. Parr, C J. Yeats

Discovered in 1991 by combined plume detection and bottom-tow photography (Binns and Scott, 1993) and for some years thereafter the highest tenor mineral occurrence known on the ocean floor, the PACMANUS hydrothermal field has since been surveyed and sampled in great detail by CSIRO and international research agencies (Binns et al, 1995; Auzende, Urabe and Scientific Party, 1996; Binns et al, 2002; Tivey et al, 2006). Since 2005 commercial surveys employing deep-tow geophysical packages and remotely-operated vehicles (ROVs) have been conducted by Nautilus Minerals Inc and partners within Papua New Guinea-granted offshore exploration licenses (Nautilus Minerals Inc, 2008). Two academic drilling programs have been conducted, one under the international Ocean Drilling Program (ODP) directed at deep structure (Shipboard Scientific Party, 2002; Binns, Barriga and Miller, 2007), and one using a 5 m capable seafloor diamond drill to investigate the immediate subsurface at one site (Petersen et al, 2005). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Harris RW, Wood BR

At any given time, the tidal force subjects massive regions to a spatially uniform load. The deformation of any large structure due to these forces is proportional to the elastic properties of the structure. In this aspect, the tidal force applies a load in a manner similar to that of a large-scale testing machine. Any anomalies in the measured tidal response must reflect alterations in the average elastic response of the massive structure. In the present work, tidal tilt measurements obtained in the wall of a large dam are used to infer changes in the response of the dam to applied loads. In particular, it is found that the dam response has changed by approximately 13 percent, on average, for two monitoring periods separated by 5 years. It is possible that these changes were produced by the different volumes of water in the dam for the monitoring periods. The tidal measurement technique can also be applied to monitor changes In the average structural response of large underground and surface masses relevant to coal and metal mines.

Jan 1, 1992

The granitoid rocks in Burma can be subdivided into three main belts viz. (1) Eastern Granitoid Belt, (2) W-Sn related, Central Granitoid Belt and (3) Porphyry Cu (Au)-related, Western Granitoid Belt. The W-Sn related, central belt Granitoids were interpreted to have generated during the continent-arc collision and the Porphyry Cu(Au)-related, western grantioid belt was emplaced in a magmatic-volcanic arc above an east-dipping subduction zone. INTRODUCTION Major tectonic domains of Burma Burma region can be subdivided into N-S trending (6) major tectonic domains from west to east (1) Arakan Coastal Strip as ensimatic Foredeep (2) Indo-Burman Ranges as Outer Arc or Fore Arc (3) Western Inner-Burman Tertiary Basin as Inter-Arc Basin (4) Central Volcanic Belt (Central Volcanic Line) as Inner Magmatic-volcanic Arc (5) Eastern Inner-Burman Tertiary Basin as Back-Arc Basin and (6) Shan-Tennasserim Massif as ensialic, Sino-Burman Ranges (Bender, 1983). The Sagaing (transform) Fault and Shan Boundary Fault form as a tectonically significant boundary between Eastern-Burman Basin (Back-Arc Basin) and continental,

Jan 1, 1987

By Oliveira JF

Thiourea is an alternative reagent for cyanide in gold leaching. The recovery of gold from acidic thiourea solutions by adsorption on activated carbon is based on methods similar to those applied for the extracting of gold from cyanide solutions, but the mechanism involved in the process is not completely understood. In the present work, studies were carried out to evaluate the adsorption of gold onto activated carbon. Experimental data showed good agreement with both the Freundlich and Langmuir isotherms. The adsorption of gold from acidic thiourea solutions proved to be an endothermic process, while the adsorption from cyanide is known to be exothermic. The isosteric heat of adsorption of -11.3 kcal/mol in the early stages of the adsorption is an indication of a process involving chemisorption. The effect of temperature was studied between 15¦C and 55¦C. An activation energy of 3.5 kcal/mol was determined by the Arrhenius plot, which indicates that the controlling step in the kinetics of adsorption is the diffusion onto the porous structure of the activated carbon.

Jan 1, 1993

By Lewis IE

Copper-lead dross is a by-product of the refining of lead bullion produced by the Imper- ial Smelting Process. This dross contains some 27 percent copper, 50 percent lead, four percent zinc and one percent sulphur. An ammonium carb- onate leach at atmospheric temperature and pressure removed the copper from the dross while the lead zinc and precious metals remained in the leach residue for return to the smelter. The leach solution containing the copper was then purified by liquid-liquid ion exchange using LIX64N in a kerosene diluent. ("LIX" is the registered trade mark of a range of hydroxy oximes marketed by General Mills Inc.) The pilot plant had a capacity of 0.7 kg/h of CuSO4,5H20 and was operated for some fifty days on a two shift basis. Copper sulphate of excellent purity was produced, and the results obtained indicated that a copper recovery of ninety percent from the dross could be expected from a commercial installation.

Jan 1, 1975

The precious metallogenic belt and its geoloqical-tectonic location in eastern China.The precious metallogenic belt of eastern China is located in the western part of the Pacific gold metallogenic belt, and occurs in the upper levels of the continent cut by a deep fault structure tending NNE and NE, and active during the Mesozoic. The precious metallogenic period ranges mainly from Late Jurassic to Early Cretaceous (160 Ma-110 Ma); subordinate mineralisation occurred during the Hercynian period, and was rare in the proterozoic.Seven precious metallogenic belts are recognised from east to west, i.e. from continent to the margin active belts, as follows:1. Au-Ag-Te metallogenic belt of East Shandong Province2. Au-Ag-Pb-Zn metallogenic belt of west Liaoning-Miyun area3. Au-Os-Ir-Cr-Cu Mo metallogenic belt of Chengde Pingquan area4. Au-Ag-Pb-Zn metallogenic belt of Zhang Xuan area5. Au-Ag-Pb-Zn metallogenic belt of Zhejiang province6. Au-Ag-Se metallogenic belt of East Qinling area7. Au-Pd-Cu-Mo metallogenic belt of Wansu area

Jan 1, 1990

By Jefferson CB

Adaptive optimisation is the adjustment of operating conditions to maintain optimum process performance as the feed quality varies. This strategy has the potential to be economic- ally better than the maintenance of a constant optimum performance with a blended feed. Application of the strategy is hindered by practical difficulties and economic risks. A computer simulation of leaching processes has been used to identify ore-process systems which have the greatest potential benefits from adaptive optimisation. They are systems with low value feed materials and a broad distribution of reactivities, in pro- cesses which are sensitive to the operating variable that is being manipulated (e.g. residence time). Improvements of up to 13% in throughput and 5% in the economic operating margin can be achieved. The results are sen- sitive to the precise model which is used for the process kinetics. It seems that the kinetics of the last few per cent to react are particularly relevant. A realistic situation has been identified where a synergistic inter- action occurs in blended feeds which makes adaptive optimisation disadvantageous.

Jan 1, 1984

By R Witt, M Lowing

Tanking of tunnels is now often specified when inflows exceed as little as 1 L/s/km with a unit distance of 100 m. To demonstrate inflows over a 100 m segment of a tunnel are less than 0.1 L/s with a standard error of 0.01 L/s by timed, gravity filled, volume measurement up and downstream of the segment, the measuring cylinder volume (L) must exceed 10 Q, where Q is the flow in L/s, and the number measurements taken and averaged must exceed 20 . If a standard error of 0.02 L/s is acceptable then 5Q2 measurements must be taken and averaged. If gravity filling is not possible then the number, n, of repeat pumped container measurement required is given by: where: is the 100 m section leakage is the volume filling time is the standard error of volume measurementZ is the standard normal variateK is a coefficient dependent on physical measurement conditions Based on analysis of field data an indicative coefficient of variation of volume measurement is ~0.05.

Jan 1, 2008

By R K. Dayal

Many transport tunnels show distress after few decades of construction. Owing to exorbitant cost of replacement, rehabilitation of tunnels has become inevitable and rapidly gaining attention/significance worldwide. This paper discusses the detailed planning and design of remedial measures for repairs and rehabilitation of the twin tube highway tunnel in India, at an elevation of 2200 m constructed approximately 38 years ago. The tunnel length is 2547 m having 30 m2 cross-sectional area of each tube. The tunnel is lined in stretches, totalling 60 per cent lined and the remaining portions are unlined. The tunnel has developed acute problems of rock falls, water leakage, distressed pavement and icicle formation resulting in slow movement of vehicular traffic which has also increased. Suffocation inside the tunnel caused deaths due to inadequate natural ventilation, hence artificial ventilation was deemed necessary and was provided in the restricted 28.5 m2 cross-sectional area of tunnel. The paper would be useful for planners, designers and construction engineers for setting future trends.

Jan 1, 1999