Search Documents

By R J. Higgins, M Edraki

What is the meaning of the Life of a Mine (LOM) if that mine results in a requirement for water treatment in perpetuity? ‘In perpetuity’ is of course a duration with no relationship to a Life-of-Mine or what might rightly be regarded by external stakeholders as a fair and reasonable post-mine recovery period. It exceeds the life span of investors, mine managers and governments, indeed even of capital markets as we know them, and of corporate and individual memories.In mine and mine closure planning, decisions are usually based at least to a significant extent on traditional economic analysis underlain by discounted cash flows (DCF). For investments in income-producing facilities, such as mining development and equipment, and ore-processing plant and equipment, this analysis reflects commercial reality and allows for comparison of competing investments. However, for environmental and social infrastructure, the same analysis using the same input parameters, especially the discount rate applied to cash flows, can lead to a bias against the adoption of best practices for non-investor stakeholders. CITATION:Higgins, R J and Edraki, M, 2018. Water treatment in perpetuity – or not?, in Proceedings Life-of-Mine 2018, pp 131–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By I T. Ross

Sampling drawpoints in block cave mines has been a contentious issue for many years. Doubts have been expressed as to the validity of the process used at most mines. This paper outlines the sampling practice commonly in use, discusses the resulting issues associated with reconciliation and drawpoint closure decisions. The paper also looks to the future and highlights issues for some block cave mining operations currently planned to have in the order of one thousand active drawpoints. It is likely that these operations will require a new approach to drawpoint sampling. There are several potential technologies currently available although some appear to be better suited than others to replace the current approaches. CITATION:Ross, I T, 2012. Sampling in block cave mines, in Proceedings Sampling 2012 , pp 81-86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By B Wentzinger

This paper presents the results of state parameter estimates in an active coal boiler ash storage facility using the most recent methods currently in use for cone penetrometer interpretation. State parameters estimates are also compared with the critical yield stress ratio approach, which is proposed as an additional liquefaction potential screening method. Recommendations are provided regarding additional in situ tests and laboratory tests that may be undertaken to improve the state parameter assessment and data produced for use in subsequent stability or liquefaction studies.

Jul 1, 2021

By T Takayama, M Matsumura, Y Konno

The steel industry accounts for 14 per cent of domestic CO2 emission in Japan, and iron ore sintering process occupies approximately three per cent. While Fe content in iron ore is gradually decreasing. So, the amount of concentrated iron ore will increase in the future. We have focused on magnetite concentrate as sinter materials, because magnetite can be easily magnetically beneficiated. However, it is experienced that blending magnetite ore resulted in increasing Fe2+ component in the iron ore sinter, which results in lower reducibility. Therefore, promoting the oxidation reaction from magnetite to hematite in the sintering process is countermeasure for reducibility. In addition, this promotion causes increase of oxidation heat, which results in high sinter strength and reduction of coke. It is assumed that the oxidation of magnetite tends to proceed in the cooling stage, where the oxygen partial pressure increases after the combustion of fine coke, but there are few studies on the effect of heat profile, especially cooling path. The purpose of this study is to design the effective sintering heat profile to promote oxidation of magnetite ore, especially, to investigate the effect of cooling path on sintered ore microstructure. In this study, magnetite ore and magnetite reagent were respectively mixed with calcium carbonate reagent. Then the mixed samples were pressed and formed into cylindrical tablets for simulating the adhesive layer of a pseudo particle. Through examining influence of maximum temperature and cooking rate on oxidation reaction of magnetite, we confirmed that the oxidation reaction of magnetite is suppressed at above 1350°C for maximum temperature, compared to 1300°C. Sintering at lower temperature is desirable because hematite is stable below 1350°C in the Fe2O3-CaO phase diagram.

Nov 8, 2021

By J Morgan

Regular monitoring of surface deformation over mine sites is important for providing updated information to managers regarding geotechnical risks related to ground instabilities. This is particularly true in cases where unexpected or accelerating movement patterns are observed, as these trends may have implications related to worker safety within active mining environments, as well as continuity of ongoing operations. InSAR is an active remote sensing technique that uses radar satellite imagery to precisely measure ground movement. This technology has started to become a standard tool for monitoring surface stability in many different sectors, including underground and open pit/cut mining applications. In recent years the launch of satellites that collect radar imagery on a more frequent basis, coupled with advances in InSAR processing techniques, has improved both the extent to which movement patterns typical of mining operations can be characterized and the temporal scale on which results can be reported to geotechnical departments. As a result of these developments, InSAR monitoring can now better meet the operational needs of mine sites. An overview of the more recently launched satellites that have a particular relevance to the monitoring of mines is provided, along with an explanation of the InSAR tools that are the most valuable to mine managers and geotechnical engineers. First, broad differences between high resolution X-band imagery and low resolution (but freely available) Sentinel imagery are discussed. Second, the various InSAR tools and their particular applications for different types of mine sites and operations are covered, which include fast delivery deformation maps for short-term reporting, multi-interferometric algorithms for longer-term analyses and rapid movement tracking (RMT) for emergency monitoring or high-risk situations. The ability of the technology to resolve 2D and 3D movement is also touched upon. Practical examples of InSAR application over a variety of mine sites will be presented, as well as surrounding hazards including landslides, to illustrate how InSAR can help provide geotechnical engineers with a picture of surface stability over the full mine site and surrounding areas to help manage risk. CITATION:Morgan, J, 2018. Wide area mapping of ground instabilities from space: InSAR for geotechnical risk assessment and hazard monitoring, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 375–382 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By D Cumming-Potvin

Incidents that trap miners in underground mines have serious consequences for the miners and the mine operators involved. It is of utmost importance that mine operators utilise all available tools when trying to locate and rescue trapped miners. From testing conducted at underground hard rock mines, Cumming-Potvin et al (2013) found that pre-existing microseismic monitoring systems, which are routinely used for seismic risk management, have the potential to be used for detecting and locating trapped miners.This paper reflects on the Anzac Day seismic event that trapped two miners at Tasmania Mine, Beaconsfield, on 25 April 2006. The Anzac Day event occurred at 2123 on a Tuesday evening. Rescuers were unable to confirm that the trapped miners had survived until 1930 on Sunday evening. It is not possible to speculate on how the rescue operation may have been different had the technology to use the microseismic monitoring system for the purpose of detecting the trapped miners been available. However, it almost certainly would have been different. The recent research project has demonstrated that knowing the fate of the Beaconsfield miners might have been achievable up to 100 hours earlier than was the case in 2006. That knowledge would have been invaluable to the rescue effort.By examining the seismic array at the Tasmania Mine, the reliability of detection over the working levels of the mine could be quantified. Had the methodology been available, adding six additional sensors (at a cost of $40 000), would have been sufficient to increase the likelihood of detection to greater than 90 per cent in the working levels of the mine. This was true both at the time of closure of the mine in 2012, and just prior to the Anzac day event.CITATION:Cumming-Potvin, D and Hills, P B, 2014. Use of a pre-existing microseismic monitoring system to detect trapped miners (with reflections on Beaconsfield 2006), in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 143–150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By A R. Penney

Safety management, both personal and that associated with catastrophic hazard, helps to define the success of mining companies. Personal safety management, often categorised by slips, trips and falls, has been widely addressed, with numerous approaches successfully adopted. Catastrophic hazard can lead to a single accident (eg ground collapse, underground fires etc) causing multiple fatalities. Catastrophic hazard management in mining is an emerging discipline, and as such there are various pitfalls to demonstrate its effectiveness and success; it is much more than simply meeting regulatory requirements. Various standards, guidelines, and leading practices are available for reporting key performance indicators. While measuring and reporting safety related key performance indicators (KPIs) such as Total Recordable Injury Frequency Rate (TRIFR), Lost Time Injury Frequency Rate (LTIFR), are important, they often lack detail, and give little insight into the effectiveness of catastrophic hazard management strategies and controls. Catastrophic hazards are low likelihood, high consequence events, and as such demand a different management approach. Companies cannot use the suite of personal safety metrics to help demonstrate management of catastrophic hazards. In-field verifications have revealed that senior management commitment to safety is often clear, well organised, and resourced. However, there are often some inconsistencies between what management promotes and plan, to what the operational teams understand and implement. Communication and clear understanding of expectations were the common themes identified to help empower supervisors to reinforce requirements of catastrophic hazard management. A lack of specific, measurable, and time-sensitive goals and objectives for the short- or medium-term, making it challenging to track progress was another key observation. Development of an integrated, multi-disciplinary auditing process executed by an experienced team of technical subject matter experts, provided an in-depth understanding of the requirements of catastrophic hazard management. Areas such as underground fire prevention, explosive storage, electrical safety, mobile vehicle interactions, ground control, inrush, and shafts and winders management have substantial overlap and intertwined processes, and similar strategies for emergency responses. Auditing of catastrophic hazards and safety management systems compliance is only the first step in safety assurance. Completing operational performance audits in technical areas and benchmarking the site verification of safety management documents and verifications forms a critical part to clearly demonstrate industry leading safety practices. No longer is it the external inspection or regular hazard management plan review requirements that dominate, but rather the culture of continual hazard identification, management, controls verification, underpinned by improvement and follow-up verifications of the corrective actions.

Mar 29, 2023

By M Dean, M Nehring, P Knights, M S. Kizil

Integrated continuous mining techniques such as fully mobile in-pit crusher and conveyor (FMIPCC) systems offer inherent labour, energy and environmental benefits to deep pit metalliferous mines. However, before such systems become commonplace, a number of barriers must be overcome.This paper outlines a number of commonly perceived barriers to FMIPCC application, together with a number of suggested solutions. The paper advances a design approach for specifying FMIPCC systems for deep pit metalliferous applications. A novel FMIPCC configuration is advanced using a hydraulic excavator in backhoe configuration. Because of the requirement to minimise belt extensions, a mine planning approach is presented based on a series of parallel and radial belt conveyor moves.The FMIPCC system does not fully replace truck-shovel systems. In the proposed mine plan, sinking is undertaken with truck-shovel systems using a series of box cuts, whereas pit ‘widening’ activities are accomplished via the FMIPCC system. Because of inherent differences in mine sequencing, the net present value derived from the FMIPCC mine will differ markedly from that derived from traditional, nested-pit, truck-shovel mining approaches. Therefore, any comparison of the FMIPCC and truck-shovel approaches must take into account radically different mine planning approaches.CITATION:Dean, M, Knights, P, Kizil, M S and Nehring, M, 2015. Selection and planning of fully mobile in-pit crusher and conveyor systems for deep open pit metalliferous applications, in Proceedings Third International Future Mining Conference, pp 219–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By B L. Sommerville

"The theme of this International Mining Geology Conference is ‘Setting New Standards’. Rio Tinto’s iron ore operations include a complex integrated supply system to deliver ore from 15 mine operations through four independent terminals over 1700 km of rail line. Significant growth in the past 20 years has seen production grow from 88 Mt in 1997 to 329 Mt for the 2016 calendar year.With more than 50 years of mining in the Pilbara, Rio Tinto has extensive experience in developing standardised approaches to mine geology and the geometallurgical prediction of product quality to meet the increasing growth profile and business planning complexity.Rio Tinto’s standardised approach to mine geology can be developed and utilised on a daily basis to enable the optimisation of the supply chain in terms of tonnages and product quality. This experience demonstrates a fully standardised system can balance the needs of a systematic process across all mine sites and the flexibility for mine geologist to determine and use local properties at each mine; this is done by ensuring two key principals are in place: a single, centrally maintained, system is established and maintained, providing a common set of processes and software across all mine sites the system allows senior mine geologists to review and customise key attributes and product regressions, ensuring site specific data is used in product predictions.The benefits of formal work process and standardisation include health, safety and environment, people and skill development, cost and improved communication. Also product predictions from mine geologists are one of the key inputs into an integrated and dynamic mine to ship scheduling system, optimising the supply chain whilst still managing the product quality. The experience of Rio Tinto is that a standardised approach to mine geology is an enabler of value for the iron ore operations.CITATION:Sommerville, B L, 2017. Mine geology standardisation – providing the foundation to consistent short-term geometallurgical product predictions in a complex multimine and supply chain environment, in Proceedings Tenth International Mining Geology Conference 2017, pp 13–20 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 20, 2017

The borehole televiewer is a downhole geophysical logging device that produces continuous, oriented, 360¦ images of the drill hole wall. Two types of borehole images are currently being generated at the BHP Billiton Mount Whaleback deposit. The optical televiewer (OTV) tool captures a ærealÆ image of the borehole wall whereas an acoustic televiewer (ATV) generates an image through variations in physical borehole size, scattering the energy from an acoustic beam. Orientation of the resulting ævirtual coreÆ is derived through magnetometers and accelerometers, providing values within one degree for both inclination and azimuth. Downhole structures such as fractures, joints, foliations and bedding planes are selected directly off the borehole image, recorded and displayed in a 3D modelling package along side adjacent drill holes. Measurements are corrected from apparent to true dip and magnetic to true north. Strata-bound magnetic anomalies are identified and corresponding measurements excluded. The importance of borehole imaging increases substantially with its ability to integrate the OTV and/or ATV data with other forms of lithological and structural data. At Mount Whaleback, the borehole televiewer has been implemented to provide information for geotechnical exploration including structural analysis, lithological characterisation and rock-mass conditions. Within the large area in and around Mount Whaleback, drilling may intersect a number of different geological formations with various rock types and conditions. With the application of the borehole televiewer, reverse circulation drilling can provide information traditionally obtained by diamond drilling.

Jan 1, 2007

By R C. Morris

Two major types of economic secondary iron ores occur in the banded iron formation (BIF)-rich Hamersley Province of the Pilbara, Western Australia:dominant BIF-hosted bedded iron deposits (BID)detrital ore deposits (DID sensu lato), which are mainly hosted in the three province-wide Cenozoic sequences that include coeval non-ore sediments and comprise:a. the major Miocene, fluvial channel iron deposits (CID)b. the lesser Eocene and Pliocene detrital iron deposits (DID sensu stricto).Striking differences exist between the massive CID resources and the much smaller underlying and overlying DID. CID are essentially riverine alluvial ooidal rocks with abundant small fossil wood fragments and variable iron peloids, but with only extremely rare recognisable lithic remnants. The original matrix is typically ramifying layered goethite. Eocene DID are mainly alluvial with minor pisoids, whereas Pliocene–Quaternary DID are dominantly coarse colluvial gravels, both derived from and largely retaining the original textures of BID, hard cap or variably ferruginised surface BIF. The colluvial DID matrix is typically ferroan-aluminous soil, resulting in canga where replaced by goethite, which may be dehydrated to hematite by exposure. The Cenozoic deposits occur in two dominant geomorphological environments: the southern Marra Mamba to Brockman Iron Formation strike valleys containing all three Cenozoic sequences and the much later northern Brockman Iron Formation plateau valleys that include only the Miocene and Pliocene sequences. The Cenozoic detritals formed in different climatic regimes, with an extended dry period forming a prominent province-wide dehydrated carapace on the Eocene DID. The Miocene ‘optimum’ followed with its thick scrub-covered deep regolith that produced the fossil wood-rich CID and was succeeded by the arid cool period of the Oakover limestone/calcrete. A major renewal of exposure and erosion in the Pliocene resulted in the extensive iron gravels of the Pliocene–Quaternary.CITATION:Morris, R C, 2015. The Cenozoic detrital iron deposits of the Hamersley Province of Western Australia – a tribute to Mal Kneeshaw, in Proceedings Iron Ore 2015, pp 319–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By A C. Robertson

World urban expansion puts constraints on the available land surface area of our major cities both for accommodating people as well as providing infrastructure and services whilst at the same time attempting to preserve the remaining natural environment. Whilst consideration is often given to underground planning for private and public transport infrastructure, the author is of the opinion that the current lack of underground planning of our cities that are suitable for underground development will have major long implications when finally the need for underground space planning is critical and ultimately recognised. This paper identifies the need for our city planners to integrate surface planning and underground planning as a ‘total planning solution’ where the city plan incorporates the elements of underground space planning as identified in this paper. Investigations by the author reveal that there are very few cities in the world that actually incorporate underground space planning in their city plans. The author uses the City of Brisbane as a case study for the potential introduction of underground space planning as part of the city plan. Despite efforts by the author to include the planning concept of underground commercial development in the latest Brisbane City Plan 2014 as well as four underground space workshops in Brisbane over the past 20 year through the Australasian Tunnelling Society (ATS), underground space planning for the City of Brisbane, apart from infrastructure projects, is not considered of significance to the City of Brisbane.CITATION:Robertson, A C, 2014. Commercial underground space – planned development for the future, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 513–518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By K Tanguturi, B Belle, R Balusu

Management of high rates of goaf gas emissions between 4000 and 6000 L/s of methane gas in longwall panels is a challenging issue, particularly in start-up areas of the panels. There is a need for investigation of the effect of various goaf gas drainage concepts and techniques, and development of effective gas drainage strategies for management of high goaf gas emissions in start-up areas of the longwall panels. This paper presents the results of various computational fluid dynamics (CFD) simulations that were carried out to investigate the effect of different goaf gas drainage strategies and combinations for gas management in the start-up area of the longwall panels. Results indicated that the gas (methane) concentration in goaf holes on the tailgate (TG) side vary between 50 and 75 per cent under the simulated field conditions with flat coal seam gradients. The results also indicated that operation of more goaf holes for draining the goaf gas on the TG side results in high ingress of oxygen and further reduction in gas concentration in goaf gas drainage holes. The simulations also included scenarios with goaf gas drainage holes on the maingate (MG) side, TG cut-through seal and near the start-up area. This paper presents the results of various goaf gas drainage strategies and discusses the effect of various combinations in order to develop effective goaf gas drainage strategies for gas management in start-up areas of the longwall panels.CITATION:Tanguturi, K, Balusu, R and Belle, B, 2015. Development of goaf gas drainage strategies for start-up areas of highly gassy longwall panels, in Proceedings The Australian Mine Ventilation Conference, pp 251–258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J J. L du Plessis, S Viviers, G Ratner

Escalating electricity costs are one of the biggest operational cost drivers in mining. The trend to use high-powered auxiliary fans delivering increased airflow to meet the dilution requirements of diesel equipment, together with the reliance on ducted systems rather than traditional flow-through systems to ventilate areas, increases the overall energy requirements of ventilation systems. To manage and reduce electricity costs energy management systems can be implemented, inefficient operating units can be replaced and the operation of energy-consuming components of ventilation systems can be optimised.This paper describes the process followed to design and develop an energy-efficient axial flow auxiliary fan. The fan-targeted design was based on static pressure and volume flow rate requirements incorporating higher overall fan efficiencies. A brief overview of the results is given, including the aerodynamic design procedure using computational fluid dynamic (CFD) analysis. The mechanical design criteria used, including stress analysis on the rotor and designs to improve the vibration levels of the fan, are also presented. Through this study it was demonstrated that the aerodynamically designed rotors using profiled and twisted blades improve the total fan efficiency considerably when compared with some of the older-generation fans using cambered plates. The latter were typical in the mining sector in South Africa at the time of the study where average overall fan efficiencies of standard cambered fans less than 63 per cent and some of the older-generation cast aluminium blades have peak overall fan efficiencies of about 65 per cent. Peak overall fan efficiency of more than 80 per cent was achieved by using the described design and development process. Additional benefits are that the fans are quieter due to the better aerodynamic design and have a longer operating life due to reduced vibration levels.In conclusion, the use of CFD to develop fans to deliver the required volume flow at the required pressure allows quicker design turnaround time. It furthermore allows the ventilation engineer the option to specify a specific fan and is not limited to an off-the-shelf catalogue fan. It thus allows engineers to purchase a fit-for-purpose energy-efficient fan. The introduction of reliable fan control systems may, however, still result in the biggest cost benefit for underground mines.CITATION:du Plessis, J J L, Ratner, G and Viviers, S, 2015. Design and development of energy-efficient secondary axial flow fans, in Proceedings The Australian Mine Ventilation Conference, pp 337–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

Detailed underground mine design and optimisation studies undertaken by the author over the past few years have clearly demonstrated that additional value can be created by varying the cut-off grade (COG) spatially throughout a deposit as well as over time. This additional value can be particularly significant for marginal operations. This paper, by way of worked examples, illustrates the conceptual and practical considerations of applying a differential cut-off policy for an underground mine to both maximise value and manage risks associated with production and metal price volatility. Consideration is given to both the design stage of a new mine and to the strategic and practical application of a differential cut-off policy in an operating mine.

Jan 1, 2005

By J E. Powalisz

"The application of automated sampling techniques can help to provide a representative sample of process fluids and slurries that provide data for controlling process, custody transfer and quality assurance and quality control purposes.The automation of sampling provides a more consistent and reliable sampling process and eliminates many of the human-induced errors. Automated sampling can also provide a higher degree of safety in the plant/processing environment as well as better bottom-line results.Automated, fixed volume samplers can provide a very representative sample by integrating many small ‘grabs’ of sample from a process. Automated samplers can be controlled in a variety of ways to optimise the sampling process, including:cycle ratedwell timetotal volume.Properly selected and applied, an automated sampler can effectively isolate the operator from the process fluid during sampling and, to a great degree, during sample container collection.A variety of materials of construction, including seals, are available to handle demanding mining applications. Alloy 625, alloy 2205, AL6XN® and even certain plastics are used successfully in mining slurry applications.This paper explores the application of automated, fixed volume, batch style samplers in copper/nickel and gold processing, specifically pregnant leach solution and extraction fluids.Several specific field applications are discussed, including process installation details, hardware and operation.CITATION:Powalisz, J E, 2014. The application of automated samplers in copper/nickel processing, in Proceedings Sampling 2014, pp 35–42 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

By D Head

IonicRE acknowledges within our mining industry, there is a common belief that workplace health and safety, often referred to as safety, is just a matter of ‘common sense’ – something obvious and easy. However, at IonicRE, we hold a different perspective. We understand that safety is far from easy. We recognise the need to emphasise the importance of understanding and conveying the inherent difficulties of working safely. We are committed to implementing processes that support individuals in achieving our safety objective of eliminating fatalities and permanently disabling injuries. To build resilience and sustainability into safety performance, we draw parallels with the principles underpinning sustainable and exceptional production performance. Achieving sustainable safety performance demands effective leadership, meticulous planning, adept management, genuine care and unwavering commitment. We’ve leveraged various tools and techniques, such as DISC theory, Maslow’s hierarchy, process control, Kaizen, Six Sigma and Kirkpatrick’s 4 levels, among others, to facilitate this improvement. There methods play a pivotal role in developing a Safety Blueprint for enhanced safety performance. This paper provides an overview of IonicRE’s Safety Blueprint, a strategic framework for developing our safety capability. Our capability is underpinned by three key pillars. Firstly, a comprehensive risk management approach is imperative, encompassing the understanding of hazards, the identification of threats to our people and the associated risks. Secondly, it entails providing and enforcing accountability to sustain our safety capability. Lastly, it involves constructing an effective defence system against threats and harm. Implementing these pillars requires a meticulously devised change process. Anticipating resistance and potential setbacks, we underscore the importance of having the right people and a wellcommunicated vision for safety at IonicRE. A Safety Blueprint serves as a detailed plan outlining the path toward a future goal. At IonicRE, we contend that safety in the mining industry has generally lacked a coherent and effective Safety Blueprint – a comprehensive plan to navigate the journey toward a destination. Drawing parallels with NASA’s detailed plan for landing a man on the moon safely, we question why, as an industry, we cannot similarly eliminate fatalities. While progress has been made in the last century, we must not wait another 50 years to eradicate fatalities from our industry. Examining Safe Work Australia data from 2008 reveals that 47 per cent of mining fatalities result from vehicle activity and 40 per cent stem from individuals being struck by an object. As of December 7, 2023, seven lives have been lost in the mining industry in Australia this year, indicating a stubborn trend mirroring 2022, with limited improvement over the past 25 years. These incidents are not isolated or unexpected. We understand the hazards and controls, yet fatalities persist. IonicRE considers that the mining industry stands at a critical juncture – do we accept a plateau in mining safety performance, or do we rethink our approach? At IonicRE, we are thoroughly reassessing the hazards that threaten our people, systematically redefining effective risk control measures and establishing a robust framework to hold individuals accountable for the effective implementation of the control measure.

Apr 16, 2024

By P M. Cepuritis

In hard rock mining, large-scale bulk mining methods such as block or panel caving (BC/PC) and sublevel caving (SLC) typically generate significant surface deformations such as subsidence. Surface deformations need to be considered in the project evaluation and planning stages of cave mines, for example, planning and location of critical underground mine planning infrastructure such as portals, haulage and vent shafts, access roads, or potential damage to existing infrastructure, changes to surface water management, waste dump, stockpile and tailings dam stability, and environmental impacts. Assessing the impact and risks associated with subsidence is a key component in robust mine planning and operations management.

Nov 29, 2022

During the first five years of operation, the Lihir gold mine has steadily increased plant throughput rate to over 4 Mtpa, well above the original design capacity of 2.8 Mtpa. Understanding how future variations in ore type impact on plant performance has been an integral part of LihirÆs development program. This paper discusses the key drivers for significant improvements to the plant, including a second oxygen plant, a pilot flotation plant, an autoclave heat recovery circuit, a pebble crushing circuit and additional autoclave feed pumping capacity. The result is a process plant with the flexibility to accommodate variations in ore type without significant loss of throughput.

Jan 1, 2003

By B Rusk, L Corriveau, P Emsbo, R P. Xavier

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Porphyry-Cu (Mo-Au) deposits and iron oxide-copper-gold (IOCG) deposits are both characterised by the presence of abundant halite-saturated fluid inclusions that reflect the circulation of hyper-saline hydrothermal brines. While it is widely accepted that brines involved in the formation of porphyry copper deposits derive from unmixing of moderate-salinity, intermediate-density fluids that exsolve from crystallising magmas, the source of brines that form IOCG deposits remains enigmatic and intensely debated. In this extended abstract, we summarise the fluid inclusion characteristics of both deposit types and present trace element compositional data for halite-saturated fluid inclusions from both porphyry copper deposits and IOCG deposits from around the world.While both deposit types typically contain halite-saturated fluid inclusions, vapour-rich fluid inclusions in IOCG deposits are less common than in porphyry deposits and evidence for fluid immiscibility is rare. IOCG deposits also typically lack intermediate-density fluid inclusions that characterise the deeper quartz-rich veins in many porphyry deposits. Many IOCG deposits contain CO2-only fluid inclusions, a type of fluid not observed in porphyry Cu deposits.Our fluid inclusion compositional data show that most porphyry Cu (Mo-Au)-related brines are dominated by Na, K and Fe and contain elevated concentrations of Ca, Cu, Pb, Zn and Mn up to around the one per cent level. On the other hand, IOCG brines are Na-Ca-Fe-dominated and typically contain far less Cu, Mn and Zn than porphyry brines. In addition to Ca, these fluids are also strongly enriched in Ba and Sr relative to porphyry-related brines. Such compositions are consistent with extensive fluid-rock interaction and/or an evolved sea water contribution to IOCG brines.A sea water or basinal brine source for IOCG brines is further supported by bromine concentrations that are much higher than is characteristic for porphyry-related brines. Porphyry brines have Cl/Br molar ratios of between 800 and 3000, which is characteristic of primary magmatic brines, whereas the Cl/Br composition of IOCG brines is more variable. For example, Na/Cl/Br ratios of most IOCG deposits in the world-class Carajás district fall on or near the sea water evaporation curve (most Cl/Br molar ratios are between 200 and 1000) and are diagnostic of sedimentary bittern brines. A few of the deposits in this district also show evidence of the input of subordinate amounts of magmatic brine. At Ernest Henry, in the Cloncurry district of Australia, most Cl/Br ratios plot close to the sea water evaporation curve, but Cl/Br ratios of up to ~5000 in several samples suggest the input of lesser amounts of magmatic fluids, and possibly evaporite-dissolution-derived fluids. Taken together with geologic constraints, these data strongly suggest that porphyry-type deposits form from the circulation of dominantly magmatic fluids, while IOCG deposits form from large-scale circulation of high-salinity fluids sourced dominantly from sedimentary basins with variable input of magmatic volatiles.CITATION:Rusk, B, Emsbo, P, Xavier, R P, Corriveau, L, Oliver, N and Zhang, D, 2015. A comparison of fluid origins and compositions in iron oxide-copper-gold and porphyry-Cu (Mo-Au) deposits , in Proceedings PACRIM 2015 Congress, pp 271–280 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015