Search Documents

By Leon H. Nelson

Several factors which affect the segregation and solidification of killed hot-topped steel ingots are: (1) pouring temperature, (2) volume in the hot top, (3) taper in the ingot, (4) pouring rate by varying the nozzle size, (5) segregation of several elements, (6) moving ingots before completely solidified. In most of this discussion, segregation will be measured in terms of carbon variation only. All the data given are results on S.A.E. 1040 analysis of fully killed steel direct-poured in hot-topped molds giving 20-in, square ingots. Thus the variables of analysis and ingot size and contour are eliminated. Segregation results are all on the rolled-bloom size, not on the ingot itself. They are results from plant-control work and not results of special research on ingot segregation. Pouring Temperature The temperature (or, more correctly, the amount of superheat above the liquidus-solidus) of the steel entering the ingot is, of course, one of the most important factors influencing segregation and solidification. Table 1 gives the average segregation of a number of heats of S.A.E. 1040 steel with normal pouring temperatures of 2775" to 2825" F. The table also gives some data on segregation in hot heats (pouring temperature 2840" to 2870" F.) and in cold heats with some skull (poured at 2725" to 2760" F.). The results in Table 1 are on steel ingots with 20-in. square cross section and 60 in. long to the hot top. The ingot weighs 7100 lb. and the hot top contains 14.3 per cent of the total ingot volume and 11.2 per cent of the total ingot weight. The results are from drillings after rolling the ingots to bloom size. Segregation results obtained on the bloom are probably not as great as they would be in the ingot itself, since heating the ingots for rolling can perhaps cause some migration of carbon from regions of high and low carbon to those of average carbon content.

Jan 1, 1937

By H. A. Coy, James A. Noble

The Mascot mines of the American Zinc Co. of Tennessee are situated at Mascot, Tenn., 14 miles northeast of Knoxville, on the Southern Railway. The district is centrally located in the Great Valley, or Appalachian Valley Province. Prior to 1900, a small output of zinc was obtained from oxidized ore mined in open pits. In 1900, a shaft was sunk to sulfide ore, and in 1903, a second shaft was put down, neither being as deep as 200 ft. The American Zinc Co. of Tennessee began drilling in 1911, and outlined an ore-body to which its No. 1 shaft was sunk, to a depth of 365 ft. Since that time, the American Zinc Co. of Tennessee has been the only operator in the district. The Federal mining laws have never been in operation in Tennessee and mining lands are as irregular in boundary and area as farm lands. Ownerships are generally held in fee. In most cases the surface and mineral rights are transferred together. Electric power is supplied at 66,000 volts by the Tennessee Power Co., from a hydro-electric plant at Parksville, Polk County, Tenn., 100 miles from Mascot. No other power is used, but an emergency steam plant is held ready in case of interruption of service. Labor is all native and non-union. Negroes are employed for most of the shoveling, and for a few miscellaneous jobs, but for almost no other work. Exploration Exploration is carried ahead of mining largely by surface drilling. Both churn and diamond drills are used. Holes are not spotted according to geometric plan, but to block out ore outlines with the least number of holes. Churn-drill cuttings from each 5-ft. run are mounted for formation record, and in ore ground, all the bailings from each 3 ft. of advance are sampled and assayed. Diamond-drill cores are sampled and a specimen core filed for formation record. In ore ground, all the core

Jan 1, 1925

By Ernest F. Burchard

The Pao deposits of iron ore are in the State of Bolivar, Venezuela, near Upata, about 30 miles south of the Orinoco River and 90 miles east of Ciudad Bolivar. They were discovered 4 or 5 years ago and have not yet been developed to the stage of mining. In March-April, 1929, the writer devoted a week to the examination of these deposits. The maps, drill records and chemical analyses presented herewith were derived from original sources, and the field photographs were made by the writer. The petrographic and metallographic data are from notes by C. S. Ross and M. N. Short, of the U. S. Geological Survey, who have kindly collaborated in these special phases of the study. The Iron Obebodies Topography and Accessibility The deposits are in a region of low mountains representing northern outliers of the Guayanan Highlands. These mountains reach altitudes of 1800 to more than 2000 ft. above sea level, as determined by aneroid barometer. The iron ore is found on mountain crests that reach altitudes of 1915 to 1930 ft., and may be followed down precipitous slopes for 200 • to 300 ft. or more. The greatest vertical range in outcrop is nearly 400 ft., and drilling has indicated that the ore extends to this depth below the surface in one place, at least. The superior hardness of the iron ore accounts for the preservation of the local mountain crests with the intermediate valleys eroded in softer granitic rock. The deposits of iron ore are reached by a private road for automobiles branching northeast from the Ciudad Bolivar-Upata road, a distance of about 12 miles. This road was used in 1928-29 by trucks for transportation of food and camp supplies, gasoline, drilling equipment, etc., but was not suitable for the transportation of iron ore. Between Ciudad Bolivar and the iron-ore area the western two-thirds of the automobile road passes through nearly level, open country known as the savanna, largely used for grazing cattle. About 96 km. (60 miles) east of Ciudad Bolivar at

Jan 1, 1931

THE refining period of an open-hearth heat blends imperceptibly into the finishing period, during which final adjustments are made in slag composition, in bath action and temperature, and in composition of the steel, in order to prepare it for casting into ingots. Operations must be governed by the consideration that alterations in the character of the heat during the finishing period must be held to a minimum. In a broad sense, the finishing and deoxidation period of a heat may be said to be- gin when the action of the last ore addition has ceased, and to end when the teeming of the ingots is completed. INGOT STRUCTLIRES A survey of the relative advantages and disadvantages of different types of ingot structure is required because deoxidation treatments during the finishing period control the amount of gas evolved during solidification and consequently determine the type of ingot structure. Four classes of ingots are recognized, de- pending upon the degree of deoxidation to which the steel has been subjected. These types are killed, semikilled, capped, and rimmed; typical examples of their structures are represented by ingots 1, 2, 5, and 7, respectively, of Fig 9-1. The actual ingots from which these cross sections were sketched were all poured to the same height (indicated by the dotted lines) in the same type and size of bottle-top molds. The eight drawings of the figure represent selected types of ingot structure in a continuous series from "dead killed" to "wild," resulting from variations in the total quantity of gas evolved, from none at all to copious amounts, during solidification of the steel in the mold. Killed and semikilled steels are adjacent at the "quiescent" end of the ingot structure series where only small amounts of gas are evolved. The term "quiescent" describes the action of the molten metal during and subsequent to the teeming of killed and semikilled steels. Capped and rimmed steels are adjacent at the

Jan 1, 1964

By Ralph Smith

DEVELOPMENT of the lime industry in Ste, Genevieve County began in a crude way in 1840. According to information furnished by the Missouri Bureau of Geology, in the early days small vertical kilns built of stone were used, and wood was the fuel. Modern development began in 1904 when one company introduced steel shells lined with firebrick. Within a few years two more companies erected similar plants, and in 1925 a fourth company began operations. Thus there are today four lime companies at Ste. Genevieve, all operating at high capacity and with a gradually increasing production. GEOLOGY The limestone of Ste. Genevieve County, which has the chemical composition and purity required for lime burning, is the upper 80 or 90 ft. of Spergen formation. The Missouri Bureau of Geology, in its geological map of Ste. Genevieve County, gives the Spergen formation a total thickness of 160 ft., but only the upper portion is pure enough for lime burning, with an average raw-stone analysis of 98.7 per cent CaCO3; 0,35 Si02; 0,3 R203; 0.35 MgCO3; 0.3 SO3. The Spergen, one member of the Meramac group, Iowa series, of the Mississippian system, underlies an area approximately 12 miles long north and south, by 5 miles wide east and west (Fig. 1) in Ste. Genevieve County. The entire eastern two-thirds of Ste. Genevieve County is sedimentary, the formations dipping gently toward the east on an average grade of about 4 per cent, or 2 ½ °. Thus the outcrops of the various sedimentaries run approxi-mately north and south. A line running west from Ste. Genevieve crosses the outcrops of the sedimentaries, ranging from the top of the Mississippian to the Ozarkian geological system in a space of 12 miles. Thus with the gentle dip of 2 1/2° the 160-ft. thickness of the Spergen formation stretches out in its outcrop so that it is approximately one mile

Jan 1, 1938

By D. K. Crampton

INTERNAL stress and season cracking in brass have been studied for many years and the technical literature contains many data on various phases of the subject. A résumé of the literature shows certain fairly well established points upon which various authors are mostly agreed: 1. Season cracking is primarily caused by the presence of relatively high internal stresses, or possibly in some cases by external stresses, or both. 2. A specific corrosion is also essential to season cracking: Certain agents, particularly mercurous salts, mercuric salts and ammonia salts; have such a specific corrosive effect. 3. The tendency to season crack under given conditions increases with increasing zinc content, brass containing less than 20 per cent zinc being relatively immune. 4. In alpha brass the season cracks are intercrystalline; in alphabeta brass they lie between the two constituents; and in beta brass they are transcrystalline. 5. The ordinary impurities or added elements in special brasses have little or no effect on the tendency to season crack. 6. Internal stresses can be eliminated, or at least reduced to a safe 'limit by annealing treatments at temperatures that do not produce visible microstructural changes or appreciable softening of the worked brasses. There are, however, some points in connection with the phenomenon of season cracking which have not been thoroughly investigated, or wherein different authors and investigators are not entirely in agreement. The investigations described in this paper were undertaken to determine: 1. The correlation between mercurous nitrate tests and actual season cracking on long-time atmospheric exposure. 2. The quantitative effect of type and degree of drawing operations on the intensity of internal stress and on the tendency to season crack in brass tubes. 3. The possibility of drawing high-brass tubes in such a manner as to prevent the occurrence of harmful stresses rather than to find a remedy for such stresses once having obtained them.

Jan 1, 1930

By R. J. Evans

THE Combined Metals Reduction Co.'s plant is at Bauer, Utah. It was built primarily to treat ore from the Combined Metals mine at Pioche, Nevada. Shortly after its completion, the company acquired the old Honerine mine, and ores from this mine, as well as custom ores from widely scattered districts, are now being treated at the Bauer plant. PIOCHE ORE The Pioche ore, which comprises about 50 per cent. of the mill feed, occurs as a replacement of an impure thin-bedded limestone. The lime beddings are separated by thin layers of micaceous shale containing appreciable quantities of sericite and graphite. The ore is an exceptionally fine-grained, dense mixture of minerals and gangue, assaying approximately 0.03 oz. gold, 7.2 oz. silver, 7 per cent. lead, 15 per cent. zinc, 16 per cent. iron, 29 per cent. insoluble and 1.5 per cent. lime. Of the total lead 7 per cent. is in the form of sulfate and carbonate. Approximately 10 per cent. of the ore consists of chert nodules impregnated with barren pyrite; the nodules average 0.8 mm. in size, and are extremely hard, compared with the other constituents of the ore. Microscopic examination of Pioche ore ground to 80 per cent. minus 150 mesh shows pyrite, sphalerite and galena still attached. EARLY ATTEMPTS AT ORE DRESSING Metallurgists, both professional and those working for private companies, have been more or less familiar with the Pioche ore since 1913; in fact, a total of 35 commercial and plant laboratories experimented with the ore between 1913 and 1921. The work during this period was decidedly negative, it being seemingly impossible to effect a satisfactory separation of the valuable minerals into marketable products. In 1913, it was recognized that fine grinding-that is, about minus 200 mesh-was required to liberate the minerals from one another, and from the gangue, but such fine grinding was not considered practicable at this time.

Jan 1, 1928

By R. J. Evans

The Combined Metals Reduction Co.'s plant is at Bauer, Utah. It was built primarily to treat ore from the Combined Metals mine at Pioche, Nevada. Shortly after its completion, the company acquired the old Honerine mine, and ores from this mine, as well as custom ores from widely scattered districts, are now being treated at the Bauer plant. Pioche Ore The Pioche ore, which comprises about 50 per cent. of the mill feed, occurs as a replacement of an impure thin-bedded limestone. The lime beddings are separated by thin layers of micaceous shale containing appreciable quantities of sericitc and graphite. The ore is an exeeptionally fine-grained, dense mixture of minerals and gangue, assaying approximately 0.03 oz. gold, 7.2 oz. silver, 7 per cent. lead, 15 per cent. zinc, 16 per cent. iron, 29 per cent. insoluble and 1.5 per cent,. lime. Of the total lead 7 per cent. is in the form of sulfate and carbonate. Approximately 10 per cent,. of the ore consists of chert nodules impregnated with barren pyrite; the nodules average 0.8 mm. in size, and ire extrcmely hard, compared with the other constituents of the ore. Microscopic examination of Pioche ore ground to 80 per cent . minus 150 nicsh shows pyrite, sphalerite and galena still attached. Early Attempts at Ore Dressing Metallurgists, both professional and those working for private companies, have been more or less familiar with the Pioche ore sinee. 1913; in fact, a total of 35 commercial and plant laboratories expenmented with the ore between 1913 and 1921. The work during this period was decidedly negative, it being seemingly impossible to effeet a satisfactory separation of the valuable minerals into marketable products. In 1913, it was recognized that fine grinding-—that is, about minus. : 200 mesh—-was required to liberate the minerals from one another, and from the gangue, but such fine grinding was not considertd practicable at this time.

Jan 1, 1928

By Stuart Croasdale

Not long ago I was called upon to conduct some experiments on the treatment of ores from the New Cornelia copper mine, Ajo mountains, Arizona, for the Calumet & Arizona Copper Co. The problem was a very interesting one and contained some unusual features. Incidental with this problem was the utilization of a large amount of low-grade pyrite in the Bisbee mines of the company, provided this could be accomplished by any feasible method. The New Cornelia mine is situated 45 miles south of Gila Bend, the nearest railroad point, on the Southern Pacific Railroad. It is about 160 miles, almost due west, from Tucson. This section is one of the most arid in the United States. The normal annual precipitation, as given by the United States Weather Bureau covering a period from 1870 to 1901, is 3 to 5 in. During June and July, 1913, the records kept by the company gave the following results. These are all I have available, but they show the enormous evaporation that can be expected, which may be a factor in leaching operations on a large scale. Temperature, Degrees F. High Low Average June...................... 112 62 84.0 ' July...................... 115 71 87.8 Evaporation June July Concrete tank, inches............ 11.7 10.72 Iron tank, inches.............. 14.8 13.07 Rainfall, inches................ None 0.77 Cloudy days................... None 10.00 Aside from several springs about 10 miles from the property, the nearest known water in quantity at the time these experiments were made was the Gila river at Gila Bend, 45 miles distant. Part of the developinent of the property of course included drilling for water in the valley, which was in progress at the conclusion of my experiments. The ore deposit itself is unusual. It consists of of intrusive plug of monzonite or granite porphyry. Chalcopyrite, bornite, and magnetite are finely disseminated throughout the magma in sufficient quantities to make the greater part of the mass commercial ore to a certain depth.

Jan 1, 1915

By R. G. Treuting, R. M. Brick

Despite the basic importance of slip in the plastic deformation of metals, and the considerable experimental investigation, thought, and speculation that have been devoted to the fundamental nature of these processes, surprisingly few data have been reported regarding the microscopic appear- ance and distribution of slip lines,‡ the external manifestation of the slip process. Photographs hitherto reproduced in the literature are in general at low or unspecified magnifications with no correlation to the prior shear. A single-crystal cylindrical tensile specimen of alpha brass about 1/2 in. in diameter, one of many previously prepared by H. L. Burghoff,1 was available for study. A plane about 3/16 in. wide, parallel to the specimen axis and normal to the plane containing the slip direction and the specimen axis, was ground and metallographically polished along the entire 5-in. gauge length. Heavy etching produced a surface free of both scratches and flow. The specimen was strained in tension until slip markings first became visible on the polished surface (Figs. 1 and 2). Re-stressing the crystal caused additional markings to appear at an initially lower stress than previously was required. Stretching the specimen to produce a dense concentration of slip lines caused such variations in level in the polished surface (normal to the slip direction) that microscopic study at higher magnifications became impossible. After annealing 15 hr. at 850°C, the specimen recrystallized to form two grains with a boundary approximately normal to the specimen axis and about midway along its length. Each was X-rayed, and two planes were again polished along the length of the specimen, in this case each parallel to the slip direction in one of the two crystals. A light longitudinal scratch parallel to the specimen axis was drawn down the center of each plane. A Huggen-berger extensometer was attached to the crystal A, whose slip plane would have the higher resolved shear stress of the two, and the specimen was again strained in tension.

Jan 1, 1942

By R. M. Brick, R. G. Treuting

Despite the basic importance of slip in the plastic deformation of metals, and the considerable experimental investigation, thought, and speculation that have been devoted to the fundamental nature of these processes, surprisingly few data have been reported regarding the microscopic appear- ance and distribution of slip lines,‡ the external manifestation of the slip process. Photographs hitherto reproduced in the literature are in general at low or unspecified magnifications with no correlation to the prior shear. A single-crystal cylindrical tensile specimen of alpha brass about 1/2 in. in diameter, one of many previously prepared by H. L. Burghoff,1 was available for study. A plane about 3/16 in. wide, parallel to the specimen axis and normal to the plane containing the slip direction and the specimen axis, was ground and metallographically polished along the entire 5-in. gauge length. Heavy etching produced a surface free of both scratches and flow. The specimen was strained in tension until slip markings first became visible on the polished surface (Figs. 1 and 2). Re-stressing the crystal caused additional markings to appear at an initially lower stress than previously was required. Stretching the specimen to produce a dense concentration of slip lines caused such variations in level in the polished surface (normal to the slip direction) that microscopic study at higher magnifications became impossible. After annealing 15 hr. at 850°C, the specimen recrystallized to form two grains with a boundary approximately normal to the specimen axis and about midway along its length. Each was X-rayed, and two planes were again polished along the length of the specimen, in this case each parallel to the slip direction in one of the two crystals. A light longitudinal scratch parallel to the specimen axis was drawn down the center of each plane. A Huggen-berger extensometer was attached to the crystal A, whose slip plane would have the higher resolved shear stress of the two, and the specimen was again strained in tension.

Jan 1, 1942

By M. Gensamer

ALTHOUGH a large number of X-ray photograms of cold-rolled steel have been published, two circumstances have led to the experimental work reported in this paper. The first is that no complete study, making use of the pole-figure method of Wever1, has been made of cold-rolled low-carbon steel. Wever has published pole figures of mild steel sub-jected to plane parallel deformation1,2 and undoubtedly he has applied the method to cold-rolled mild steel, but the authors have not found these data published. Kurdjumow and Sachs3 have applied the method to the study of rolling and recrystallization textures in electrolytic iron; their results will be referred to later. The reason for this dearth of papers using the pole-figure method is obvious; a greater number of photograms and more analytical work (although this work is quite simple and straight-forward) are required to construct a pole figure than most investigators have felt worth while, despite the fact that no other method of which the authors are aware will satisfactorily depict the orientations of the crystal-lites in a polycrystalline aggregate. The second circumstance that led to the work reported in this paper was the appearance of a paper by Wayne A. Sisson4 on the same subject. In his valuable study of the factors influencing the development of pre-ferred orientations in cold-rolled mild steel, Sisson made one observation that required confirmation; that is, that at some stage of the rolling proc-ess the type of preferred orientation changed from the type that gives a photogram characterized as a "six-point" X-ray pattern to that known as a "four-point" pattern. A similar observation had been made by Tam-mann and Heinzel5, who studied the orientations developed in the rolling of steel by the specular reflection of light from the etched surface of rolled samples. These workers also found that the type of preferred orientation

Jan 1, 1936

By Hans Conrad, W. D. Robertson

FORMAL theories of yielding and flow have been developed to describe thermally activated plastic flow in metal crystals.'-" hey are all based on Becker's' original idea that thermal fluctuations aid the applied stress in overcoming internal barriers to flow and lead to the following relation. where j is the strain rate; C is a constant which includes a frequency factor, the entropy, the number of flow units, and the amount of strain associated with each successful fluctuation; E(T) is the activation energy associated with flow, and is a decreasing function of the applied stress, 7; k is Boltzmann's constant; and T is the temperature in OK. The various theories differ mainly in the model chosen and in the nature of the relationship between the applied stress and the activation energy. Beckerl and Orowan' suggest a relationship of the form E a(Ti — t)2, where .ri represents the stress required for flow without the aid of thermal fluctuations; Kauzmann,3 Cottrel1,5 and Seeger6,7 suggest E a(t — t) ; Fisher8 suggests E while Cottrell and Bilby4 suggest a more complex relationship between E and 7. Additional data are needed to test these various theories., esweciallv- in view of Dorn's9 ork. which indicates that the activation energy for creep is independent of the stress and strain. The present paper presents the stress-strain data derived from incremental loading of magnesium single crystals in tension and direct shear, in the temperature range of 78" to 364°K. Incremental loading was employed in order that the creep component of the strain could be determined. Stress-strain curves of aluminum10-13 and copper" single crvstals. derived from incremental loading tests, have been found to be in agreement with those obtained by the more conventional constant strain rate or loading rate tests. Two types of tests were conducted in the present investigation: 1) tests in which the temperature was maintained constant throughout the entire

Jan 1, 1958

By R. V. Norris

It was stated in a former paper1 that an intensive study of anthracite costs was being made by the engineers of the United States Fuel Administration. The results of this study are now available and are offered as a supplement to the former paper. Anthracite costs as reported for the 6-months period, December, 1917, to May, 1918, inclusive, as compiled by the Federal Trade Commission, were used as a base, and charts similar to those described in the former paper were made for the standard white ash anthracite and for red ash and Lykens valley coals. Adjustments The adjustments of cost from a reported to a price-fixing basis, as described for the bituminous methods, were applied but showed only minor adjustments as necessary. The great spread in anthracite prices on the varyingsizes, which for the 6-mo. period under review ranged in average from $5.244 for nut to $2.074 for barley coal, makes the question of the percentage of sizes produced at the different collieries a vital one. The realization with the same prices for each size must be within very wide limits, when it is considered that the percentage of prepared coal reported from different collieries varied from over 80 per cent. to below 30 per cent. for fresh-mined coal. Hence, as the spread in prices for the various sizes must be predicated on some percentage, it is essential to find some method of adjustment to allow for this variation. The logical method of adjustment is to calculate actual costs to costs as of the standard percentage of sizes, so that the margin between the adjusted costs and the average realization shall be the actual margin for each colliery between its actual costs and actual realization due to its particular percentage of sizes. As a base for realization the actual percentage of sizes for fresh-mined coal for the 6-mo. period was adopted. This percentage is given in Table 1.

Jan 1, 1920

By Walter R. Hibbard

THE term lineage was first introduced by Buerger1 to denote dendritic branches, grown from a crystal nucleus during solidification from the liquid, with imperfections in alignment of the order of 10-1 [ ] to 10-4 cm. These imperfections are associated with distortions of the dendrites caused by the subsequent solidification of the inter-dendritic filling and are illustrated in Fig 11. Buerger etched zinc single crystals made by the Bridgman2 method to develop this dendritic pattern and show lineage microscopically. Since maximum crystal growth in face-centered cubic metals occurs along the [100] directions,2 lineage would appear in copper as small deviations of dendritic branches from these directions. Elam4 and others5-8 reported etching effects resulting from coring along the cube face traces of various copper alloy crystals. These traces were used by Samans8 to orient single crystals. Williamson9 noted a "lined structure (in alpha brass single crystals) consisting of an ordered arrangement of etch pits" which were probably traces of {100} planes but somewhat uncertain because they were never straight (i.e., apparently lineage). Greninger10 described the distortion and multiplicity of Laue spots in back reflection X ray photograms of copper single crystals showing lineage. The present investigation includes metallographic, X ray and property studies of lineage in large grain and single crystal specimens of copper. PREPARATION OF SPECIMENS Specimens 10 in. long and ½ in. diam of oxygen-free copper (O.F.H.C.) (99.985 pct) were melted vertically in graphite crucibles under an atmosphere of commercial nitrogen purified through a gas train including sulfuric acid, potassium chloride, magnesium chlorate, hot copper chips and phosphorus pentoxide. After a temperature of 1200°C had been maintained for ½ hr, the furnace was turned off and the specimens cooled at a rate of about 150°C an hour. This method of direct solidification was used by Greninger10 to produce single crystals with marked lineage and in this investigation produced a fair yield of single crystal specimens in

Jan 1, 1947

By H. A. Baumann, A. J. Rostosky

EVER since the first installation of wet-washing methods of coal preparation, the removal of the water added by the washing process has created serious technical and operating problems. The rapid development and widespread adoption of wet washing has necessitated a corresponding development of dewatering methods and equipment. The amount of water retained by coal varies with the size of the coal. The moisture that is largely on the surface of the particles is easily shaken off coarse coal; thus coarse coal can be dried comparatively easily and quickly. Fine coal presents a larger surface area than does coarse coal, so its capacity for retaining moisture is greater. In fine coal, moisture below about 5 per cent is held between the coal particles and its removal is difficult. Draining and drying of the finer sizes is a major problem at many washeries. Two common problems of coal-washing practice that are intimately connected with dewatering and drying are the clarification of washery water and the prevention of stream pollution. The first field has been studied from many angles, including the use of coagulating and settling agents followed by vacuum filters to remove the solids, and the use of sludge tanks with dewatering screens incorporated therein. In many districts, the disposal of sludges into streams has been stopped by law. The lack of space for impounding sludges has created problems of disposal in other districts. Reduction in moisture means a saving in freight costs as well as the elimination of difficulties in unloading and storing. Excess moisture in coal causes it to freeze in localities where severe climatic conditions prevail. Excess water in coals to be used in the production of coke and manufactured gas has a chilling effect on the walls of the oven or retort. Dryness of coal is important in producing good briquettes. CLASSIFICATION OF MOISTURE Moisture in coal can be classified as inherent and surface moisture. Inherent moisture is regarded as a part of the true coal substance, having been present in the original vegetal matter from which coal was

Jan 1, 1943

By J. W. Halley

RIMMING steels derive their name from their action during solidifica-tion in the molds. As a result of incomplete deoxidation, gas is evolved during freezing, and the metal has a characteristic rolling action. The metal rises along the mold walls and descends in the center of the ingot. This action keeps the top of the ingot open and the advancing rim of solid metal can be seen. The rim grows until the rolling action is insufficient to prevent the top of the ingot from freezing or until the action is stopped by capping the ingot with a heavy plate. The violence of the reaction and its characteristics, such as growth or drop ill the molds, are deter-mined by the Composition, the furnace practice, and the deoxidation in the ladle and in the molds. Though rimming steels represent a large proportion of the amount of plain carbon steel made, they have received comparatively little attention in the technical literature. The manufacture of rimming steels has been described by Hibbard,1,2 Fleming,3 Pierce4 and Jackson.5 The reactions occurring during rimming have been considered from the theoretical point of view by Chipman and Samarin.7 The structure of rimmed-steel ingots has been discussed by Nead and one of the present authors.6 Meyer,8 in studying segregation, investigated the distribution of carbon, sulphur and phosphorus in rimmed-steel ingots by analyzing the rim and core of blooms. In their studies of segregation, the Joint Committee of the Iron and Steel Institute and the British Iron and Steel Federations studied distribution in one billet and one ingot of rimmed steel. A detailed study of the distribution throughout the ingot has not been published. The present investigation was undertaken to determine accu-rately the distribution of carbon, manganese and sulphur in normal rimmed ingots and the general distribution of other common elements present. The study included some work on the effect of pouring condi-tions and furnace practice on the distribution, though there is still much to be done in this direction.

Jan 1, 1938

By D. Turnbull, J. E. May

THE (110) [001] texture in silicon iron is of considerable interest both from the technological and scientific points of view. Its occurrence was reported more than 20 years ago.1-4 The texture develops by means of secondary re crystallizatjon5 and can be very strong, that is, greater than 90 pct alignment even thouh the primary re crystallization texture is weak or complex. This behavior is in contradistinction to the face-centered metals which develop their strong secondary recrystalliza-tion texture from a strong primary recrystalliza-tion texture.', The microstructural changes accompanying the (110) [001] texture formation in silicon iron are as follows: When properly prepared cold-rolled sheet (i.e., 0.015 in. thick) is annealed at about 800°C, primary recrystallization occurs and a fairly stable fine-grained primary recrystallized matrix of about 0.02-mm-diam grain size is produced. The material at this stage does not have the strong (110) [110] texture. As the temperature is raised to about 900°C, relatively large grains appear in the finegrained matrix and they grow at the expense of the smaller grains to many times the sheet thickness. In time the complete sample is consumed by these large grains. This process of the growth of relatively few grains (about one in 105 primary grains) at the expense of many grains is called secondary recrystallization. Since all the secondary grains are of essentially (110) [001.] orientation, the strong texture is developed by this secondary recrystallization process. Theories of the (110) [001] texture in polycrystal-line silicon iron have been proposed by Decker and Harker and by Dunn.Decker and Harker have shown that grains initially in the (110) [001] orientation will upon annealing after cold-rolling, re-crystallize back to the initial orientation. To account for the sharp texture in silicon iron they propose that (110) [001] grains become more highly strained than grains in other orientations and therefore recrystallize first. They are then the lowest energy grains and can consume their higher energy neighbors. Grains in orientations other than (110)

Jan 1, 1959

By Aug. J. Jr. Bowie

(Read at the Wilkes-Barre Meeting, May, 1877.) Brief Outline of the General Topography of the Gold Regions of California. THE topographical features of California, as demonstrated by the explorations of the State Geological Survey, are found to be exceedingly simple. Three equidistant parallel lines can be used in conveying a general idea of the physical geography of Central California. A straight or " main axial line," whose course would be north 31° west, passing through the culminating peaks of the Sierra for a distance of five hundred miles, can be assumed as the eastern boundary of the State. A second parallel drawn fifty-five miles west of the " main axial line" will skirt the western base of the Sierra Nevada, along the edge of the foot-hills. A third parallel run equidistant from the second will represent "as nearly as possible the western base of the Coast Ranges." These parallel lines divide the State into three belts, namely, the Sierra, the Great Valley of California, and the Coast Ranges. " This arrangement of the physical features holds good for a length of four hundred miles in the direction of the main axial line, comprising almost the whole of the agricultural and the greater part of the mining districts."* The section of the country which is of immediate interest to the miner is the western slope of the Sierras. These mountains, rising in a short distance from the Sacramento plains to elevations of over seven thousand feet, with occasional peaks ten and twelve thousand feet high, are cut by numerous deep and precipitous gorges or capons, through which drains the immense watershed of the Sierra, supplying the main rivers of the State and ultimately emptying into the Pacific Ocean. Between these capons, ridges or divides are formed, on top of * See vol. i, p. 5, Geological Survey of California. J. D. Whitney, State Geologist.

Jan 1, 1878

By M. J. Sinnott, W. R. Kiessel

The creep characteristics of commercially pure titanium sheet in the annealed state, cold-worked state, and cold-worked and recovered state in the temperature range from 75' to 750°F have been determined. Titanium has been found to exhibit strain aging characteristics. The effect of strain aging on creep has been determined. A possible explanation for the poor creep properties of titanium is proposed. THE metal titanium exhibits many desirable properties but results on its creep properties have been somewhat disappointing. The creep strength is low even though the material has a very high melting point.' The present work was undertaken to determine the creep strength of titanium in various conditions; annealed, cold-worked, and cold-worked and recovered and to determine why titanium shows such relatively poor creep properties. The general procedure followed in this research consisted in obtaining the usual mechanical prop- erties such as creep strength, short time tensile strengths, and hardness on materials treated to a controlled degree of internal strain, as determined by X-ray diffraction measurements, and their subsequent interpretation in terms of this internal strain. The material used in this work was sheet stock taken from one heat of commercially pure titanium. As-received, this sheet was 0.060 in. thick. The analysis was given as 0.037 pet C, 0.023 pet Si, 0.50 pct W, 0.063 pct Ni, 0.08 pct Fe, and the remainder titanium. The oxygen and nitrogen were unreported but generally are about 0.2 pct in commercial heats. In order to put the material in a state of minimum internal strain all the sheet was given an anneal in a static argon atmosphere for 1 hr at 1600°F prior to processing and testing. The microstructure of the material after this treatment was essentially a single-phase solid solution of uniform equiaxed grains. For the studies on the cold-worked sheet, the material was reduced by rolling in a two high, 5 in. mill. Rolling was done at room temperature in passes

Jan 1, 1954