Search Documents

By G. A. Reinhardt, H. J. Cutler

ThE Youngstown Sheet & Tube Co. has produced a large tonnage of 0.35 to 0.45 carbon forging steel, the acceptance of which was based on the physical properties of test specimens obtained by forging the original 5 3/4-in. (14.5 cm.) square bloom to a 3/4-in. (1.9 cm.) round. Annealed and tempered specimens were required. The test bars were annealed by heating from 900" to 950' C. and cooling slowly in mica. The test bars were tempered by heating to 825' to 875" C., quenching in water, and drawing to 515" to 535" C. Immediately after heat treatment, the test pieces were machined to a diameter of 0.534 in. (1.38 cm.) and tested. Very good physical properties were obtained and no difficulty was experienced in meeting the specifications called for. UlTimate Strength.. Elongation, Lb. pER Sq. In. PEE Cent.. in 4 In. Not LeEs Than Annealed specimens.............. 78,230 to 92,450. 18 Tempered...................... 120,000 to 149,350 9 After experience on this material, production of slightly higher carbon forging steel was started. The method of testing this material required that test blooms be either normalized or annealed. The normalizing consisted in heating to 850" to 900" C. and cooling in still air; the annealing, in heating to 850" to 900" C. and cooling in the furnace or in mica. From the treated bloom, the test pieces were taken either by core drilling or by sawing from points midway between the edges and the intersection of the diagonals. The cores or blocks were turned to a standard 2-in. test piece with a diameter of 0.564 in. and tested without further treatment. The physical requirements of the test pieces were: yield point, pounds per square inch minimum, 44,800; ultimate strength, pounds per square inch, 89,600 to 112,000; elongation, per cent. in 2 in. not less than 17. Difficulty was encountered as soon as work on this material was started. Many precautions and refinements were instituted but it was found very difficult to secure the required elongation.

Jan 1, 1920

By Edmund D. North

In making a glass model of mine-workings, each mine will present some little individualities, to meet which will call for the exercise of special ingenuity. Having made several models, I offer the following details of the model of the Montana-Tonopah mine-workings, believing that with small changes for different conditions the method described can be successfully used in making a glass model of the workings of any mine. The model, Fig. 1, has the top, one end, and the front removed. The case is made of kiln-dried pine, painted with several coats of dead-white paint. It is made to take sheets of glass 24 by 42 in. in size, and is 18 in. high, the workings shown being on a scale of 1 in. = 40 ft., or 4800 : 1 scale. The base is made of four pieces of 2-in. material, well pinned and glued together. The back, of material 1 in. thick, is secured rigidly to the base by screws and countersinking. The four posts, 1.5 in. square, are so cut that the front and two ends of the model fit in flush with the outside edges of the posts. The top rails, 1 in. square, are fastened rigidly to the front and back posts by means of small iron braces. The ends, front, and top of the case are of 0.5-in. material; the ends and front are held in place at the bottom by pegs fitting into the base ; at the top the ends are held by buttons and the front by cupboard-hooks on the inside. Hinged hasps on the cover, fitting over staples in the end-pieces, make it easy to lock the entire case. Before the back is fastened to the base, it is cut with horizontal and vertical grooves to receive the horizontal and vertical sheets of glass, shown clearly in Figs. 1 and 2. The horizontal grooves, spaced to scale, represent the vertical distances between the levels at the shaft. The vertical grooves are placed wherever cross-sections of the workings are desired.

Jan 1, 1910

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of complaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and insure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage o~ breakage en route. The small sizes present in a car-of prepared coal as received by the purchaser consist of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers' loss because of breakage in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal. An Ohio dealer estimates the degradation in loading and shipment of West Virginia coals consigned to Ohio cities as follows: Pocahontas lump

Jan 1, 1950

By P. R. Bradley

The property of the Alaska Juneau Gold Mining Co., covering the Juneau gold belt for over a mile in length, consists of 136 claims and 24 mill sites; these are near Juneau, Alaska, in what is known as the Harris mining district. Gold was discovered in the district in 1880, by Richard T. Harris and Joseph Juneau, who had been prompted to explore the section by rumors they had heard among the Indians. Gold was first found on the beach at the mouth of Gold Creek and further search revealed the lode deposits in the Silver Bow basin, about two miles inland. The lode locations made immediately thereafter constitute the principal area of the Alaska Juneau group of claims. Gradually news of the strike spread and, during the late eighties, Silver Bow basin became a substantial producer of gold, both from placer work and from quartz milling. Numerous small mills of various types were erected to crush high-grade float and stringers gouged to shallow depths. Placer mining gradually ceased and the pioneer milling operations gave way to larger and better mills, which in time were the predecessors of the two large mills built by the Alaska Gastineau Co. and the Alaska Juneau Co. on the shores of Gastineau Channel. This evolution from arrastres to small mechanical mills, thence to the two large-capacity mills on Gastineau Channel, although a natural sequence of events, had a most important bearing on the development of the district. Knowledge of the character, extent, and value of the ore deposits gained by these early operations could not have been acquired otherwise. Spencer shows1 that the early mills were: Arrastres in 1881-82-83-84-85-86-88; a 5-stamp mill in 1882; a "newly devised grinding mill" in 1884; two Huntington mills in 1886; a 10-stamp mill in 1889; a revolving Dodge mill in 1890; a 5-stamp mill in 1891; and a 20-stamp mill in 1893. He also estimates the gold production to the end of 1893 as $1,000,000 from lode mining and $1,250,000 from placer mining. No estimate can

Jan 1, 1925

By Y. A. Chang

Heat content values of tantalum monocarbide and tungsten monocarbide have been determined from 325" to 985°K by means of a drop-type diphenyl ether calorinzeter. Based on the values obtained in the present study and those available in the literature, best values lected and computed from 298. 15°K to temperatures close to their respectiue melting points. At temperatures higher than 1700°Kfor TaC and 27000 K for WC, values of Cp and related thermodynamic quantities were extrapolated based on the two Debye parameters: one corresponds to the metal sublattice and the other to the carbon sublattice. The contrzbutzon In the total specific heat due to lattice dilation was evaluated using the Nernst-Lindemann relalionship. The calculated values of Cp were in good agreement with the In view of their refractoriness, tantalum monocar-bide (TaC) and tungsten monocarbide (WC) are of con- experimentally determined ualues. Furthermore, the calculated values of the absolute entropies at 298.15"K were 5.03 and 4.15 in comparison to the experimental values of 5.05 and 4.15, all expressed in the unit of cal per degg-atom. Using the same Debye parameters, values of the linear coefficients of ther mal expansion for TaC and WC were calculated from absolute zero to their respective melting points using the Grüneisen equation. The calculated values are in excellent agreement with the experimental values available in the literature. Finally, the values of the bulk modulus of TaC from room tenzperature to temperature near its melting Point were also calculated using the equation recently derived by Anderson. No cot~ipari-son between the calculated and experimental values can be made due to lack of experimental data. siderable practical interest. In order to completely define these materials, it is necessary to know their thermal properties as a function of temperature. Tantalum rnonocarbide having a NaCl structure (B-1 type) melts congruently at 4250PK,1 while tungsten monoearbide with a simple hexagonal structure (Bh type) melts per itectically at 3049°K into melt and graphite.2 In the present study, the heat content values (from which

Jan 1, 1968

By EDBIUND U. NORTH

IN making a glass model of mine-workings, each mine will present some little individualities, to meet which will call for the exercise of special ingenuity. Having made several models, I offer the following details of the model of the Montana-Tonopah mine-workings, believing that with small changes for different conditions the method described can be successfully used in making a glass model of the workings of any mine. The model, Fig. 1, has the top, one end, and the front removed. The case is made of kiln-dried pine, painted with several coats of dead-white paint. It is made to take sheets of glass 24 by 42 in. in size, and is 18 in. high, the workings shown being on a scale of 1 in. = 40 ft., or 4800 : 1 scale. The base is made of four pieces of 2-in. material, well pinned and glued together. The back, of material 1 in. thick, is secured rigidly to the base by screws and countersinking. The four posts, 1.5 in. square, are so cut that. the front and two ends of the model fit in flush with the outside edges of the posts. The top rails, 1 in. square, are fastened rigidly to the front and back posts by means of small iron braces. The ends, front, and top of the case are of 0.5-in. material; the ends and front are held in place at the bottom by pegs fitting into the base ; at the top the ends are held by buttons and the front by cupboard-hooks on the inside. Hinged hasps on the cover, fitting over staples in the end-pieces, make it easy to lock the entire case. Before the back is fastened to the base, it is cut with horizontal and vertical grooves to receive the horizontal and vertical sheets of glass, shown clearly in Figs. 1 and 2. The horizontal grooves, spaced to scale, represent the vertical distances between the levels at the shaft. The vertical grooves are placed wherever cross-sections of the workings are desired.

Jan 1, 1910

By A. R. Rosenfield, G. T. Hahn

The effects of adding 0.025 volume fraction of uniformly dispersed Tho2, particles (particle size -380A) to iron have been examined. The two-phase alloy is shown to have a lower transition temperature and higher cleavage stress than either the base metal or a solid-solution alloy (Fe-3Si). Enhanced cleavage resistance is thought to be a consequence of particles limiting the effective slip distance of dislocations and thus the ability of Pile-ups to act as stress concentrations. Further calculations predict that the highest cleavage strengths are attained with uniform dispersions, where the particle size is kept small (-250A) and the volume fraction is relatively large (-2 to 3 pct). ALTHOUGH a fine dispersion of second-phase particles is known to impart strength to an alloy, the possibility that it might also impart ductility has only recently been explored. Outstanding progress has been made in the production of ductile tungsten alloys containing Tho21,2or (Hf, Zr)C,= but the contribution of the dispersion to ductility has neither been optimized nor fully analyzed. The basis for such an analysis has now been developed1,5 and is discussed briefly below. Experiments on iron are also described that attempt to isolate one of the possible ductilizing mechanisms and test its effectiveness. In analyzing these experiments, it is important to remember that cleavage obeys a stress criterion, and that either a lower ductile-to-brittle transition temperature or a higher cleavage stress is evidence of enhanced resistance to cleavage. DUCTILIZING MECHANISMS Slip Blockage. Cleavage fracture of polycrystals may be initiated at the intersection of a slip band (or twin) and a neighboring grain or a large (-1 to 5 µ) particle. The slip band generates a stress concentration at its head, and either the grain boundary fractures, the particle fractures, or cleavage is initiated in a neighboring grain. Experimental evidence for this viewpoint is found in metallographic studies8-8 and from the observation that cleavage is usually preceded by yielding.8-11 The potency of a slip band as a stress concentrator

Jan 1, 1968

By William Blauvelt

THE type of gas producer in which the ashes are fluxed and run off as slag was among the very earliest made. Ebelmen built the first one in 1840 at Audincourt, France, only a year after the installation of the first gas producer of which we have record. Charcoal was used as the fuel, with blast-furnace slag and clay is flux. My interest in this type of producer began when as a boy I saw the fluxing producer at Chester, N. J., which was invented by W. J.. Taylor, and described by him in 1881.1 This producer was invented independently by Mr. Taylor to meet the difficulties he experienced in making producer gas for roasting sulphurous iron ores. It will be of interest to review briefly his description of his producer. It was built like a small blast furnace, having a hearth 24 in. in diameter and 24 in. high. The bosh angle was 25° from the vertical; the diameter at the bosh 4 ft. and at the top 3 ft.; the total height 12 ft. The producer contained one water-cooled tuyere 12 in. above the bottom, with a 1.5-in. nozzle.. Depth of the coal above the tuyere; 6 ft. Mr. Taylor mixed the coal with from 30 to 40 per cent. of basic blast-furnace slag to flux the ash. Occasionally some limestone was also used, but never limestone alone, as the use of the furnace cinder gave a larger volume of slag and made it easier to maintain a proper fluidity. . The producer was blown with a small Weimer blowing engine, delivering 300 ft. of air per minute, at from 1 to 1.5 lb. pressure. The slag was tapped every 2 hr. and was black and glassy in appearance. Broken or egg size anthracite was used. The fine sizes of anthracite could not he made to work. Mr. Taylor expressed the belief that bituminous coal could be used if not too fine, but no experiments were made with this coal. Runs were made of four weeks' duration, with no stops or changes. Mr. Taylor reported the following advantages:

Jan 12, 1913

By R. E. Rick-Secker, W. M. Baldwin, R. McC. Baker

The development of residual stress in strip during rolling has not been systematically studied. A few scattered papers1 -3 mention the existence of residual stresses in rolled strip or touch upon some of their consequences,4 but there is no report of experimental studies in the literature describing the effect of roll diameter, strip thickness, reduction per pass, metal or metal temper on the magnitude of residual stresses developed in strip. A knowledge of the effect of these factors is of utmost importance since the present trend in some mills to roll thicker castings brings the rolling operation directly into that set of conditions which, as will be brought out in the present paper, can develop residual stresses of a high order of magnitude. Fundamentally, residual stresses are developed when a metal is inhomogeneously unloaded from a plastic stress state. A quantitative treatment of the problem requires a reasonably complete understanding of both the plastic stress state existing in the metal during deformation and the elastic stress state that would exist in the metal if the metal deformed as a perfectly elastic body. Our knowledge of either state during rolling is so meager that we can make no more than certain limited predictions. The external stress state* operating between the roll and the metal consists of Fig i—External stress state operating on metal being rolled (after siebel and LUEG5) compressive stresses acting almost perpendicularly to the strip surface but varying in intensity both across the width of the strip and along the length of contact between the roll and the strip. An example of such a stress distribution is shown in Fig I. The nature of the internal stress state, produced by this distribution, is not known. Various investigators,5-7 however, have felt that a qualitative similarity must exist between the internal stress state so produced and that produced in a wide strip that is compressed between two flat-nosed punches. In the latter case the external stress state is represented by a uniformly distributed compressive stress acting per-pendicularly over the face of the tool. The

Jan 1, 1949

By Paul A. Farrar, Felix Ermains, Harold Margolin

The systems Ti-Crand Ti-Vhave been reinvesti-gated in the region up to 40 wt pct alloying addition using both conventional and rapid quenching techniques. The Ti-Cr eutectoid temperature was determined to be at 667° & 10° C and 14.5 wt pct Cr. The solubility of the Cr in a Ti was found to be less than 1 pctat 700"C. The P transus of the Ti-V system was found to be depressed to 510°C at 40 wt pct V and the solubility of V in a Ti was found to be less than 2 wt pct at 700°C. Investigation by a. d. McQuillan1-3and m. k. McQuillan4 on the systems Ti-Co, Ti-Cr, Ti-Cu, Ti-Fe, Ti-Mn, Ti-Ni, and Ti-V has cast doubt as to the position of the ß/a + ß boundaries in many of these systems. Their investigations were carried out using hydrogen pressure and/or rapid quenching experiments, as opposed to the conventional quartz capsule techniques employed by most other investigator.'" By these methods, the ß/a + ß boundary was found to be lower than that obtained by conventional techniques in all except the Ti-Fe system. In the latter, the ß/a + ß boundary was essentially the same as the boundary obtained by conventional technique.7' On the basis of rapid quenching results in the Ti-Cr system, M. K. McQuillan4 placed the eutectoid temperature below 550°C whereas other investigations using conventional techniques had placed the eutectoid variously as between 650' and 700°C,5 between 675' and 700°C,6 between 650" and 675°C,7 at 670°C,8 and above 625"C.la9l3 In order to check these results, a reinvestigation of four of the systems was undertaken using both conventional and rapid-quenching techniques. The Ti-Fe and Ti-Mn systems will be dealt with in anoth er paper, with only the Ti-Cr and Ti-V systems being discussed here. EXPERIMENTAL TECHNIQUES Alloys employed for the delineation of the systems under investigation were prepared from iodide titanium sheet capsules containing the alloying materials,

Jan 1, 1962

By Philip N. Adler, Harold Margolin

Univariant equilibria between the Ibcc, IIhcp, and UIfee phases of thallium have been determined and indicate a triple point at 110°C and 37 kbars. Calculated II —I transformation curves are compared with the experimental. Transformation volumes and/or enthalpies are calculated and enthalpies are compared with available data. ThE triple point of solid thallium has been reported by Bridgman as 153°C and 38 kbar.' More recently, Jayaraman et at.2 have reported the triple point as near 115°C and 39 kbars. Meyerhoff and Smith,3 assuming the elevated-pressure modification of thallium is fcc, as Kaufman suggested,4 and that it is continuous with the room-temperature fcc phase in the Tl-In system, have used pressure data up to 5 kbars to predict the triple point at 162°C and 35.8 kbars. Piermarini and weir5 have indeed found the elevated-pressure phase to be fcc. The effect of variations of pressure and temperature in the IIhCp — Ibcc transformation in thallium have also been reported by werner6 and more recently by Ponyatovskii.7 The work reported here is part of an investigation of the effects of temperature and pressure on the Tl-In system. I) EXPERIMENTAL PROCEDURE The onset and progress of transformation were determined by changes in resistance. A commercially available tetrahedral-type pressure apparatus was used. Specimens of 0.060 in. diam, representing 0.63 pct of the cell volume, were encased in AgCl and mounted in pyrophyllite, as shown schematically in Fig. 1. It can be seen that the specimen is in series with the graphite furnace. Resistance changes of 0.1 pct could be detected with a Kelvin bridge. Resistance of the sample was of the order of 1 milliohm. Other pertinent details in regard to calibration and cell-assembly design are given elsewhere.' Temperature calibration of the cell was carried out in two ways as a function of input wattage. Through a hole drilled in the graphite furnace, a chromel-alumel thermocouple was inserted into the AgCl to a point 0.010 in. from the sample, with the

Jan 1, 1964

By F. Wartenweiler

Much has been written on milling and cyanidation as practiced on this gold field, therefore the purpose of this paper is to record its development only briefly and to describe in more detail the contemporary state of the science and art of this branch of metallurgy. It is a pleasing task, because a steady evolution is to be recorded. Definite trends influenced the development. Some have the stamp of original thought and observation; many have been achieved from a logical sequence of planned experimentation and research; while others have resulted from the drive of sheer necessity. The large scale of operations and capital outlay has compelled conservative progress. Banket ORe For a better understanding, a review of the characteristics of the ore may not be out of place. The Witwatersrand gold ore is named "banket" from the similarity of the oxidized outcrop ore to the Boer almond cake of that name. The inter bedded orebody is commonly called "reef." It is a conglomerate composed of various sizes of pebbles, principally non-gold-bearing white quartz, which constitute about 70 per cent of the bulk, within a matrix of cementing material consisting of fine-grained quartz, sericite, chlorite and chloritoid and containing the precious metals and mineral sulfides. Argillaceous components in the mil pulp may be as high as 32 per cent. Of the sulfide minerals, pyrite and pyrrhotite are predominant. Most base-metal sulfides are present, but sporadically and generally only found in highly concentrated mill products. In the latter, osmiridium is recovered in varying amounts; from 1 oz. in 3000 tons to 1 oz. in 10,000 tons of ore. Most of the oxidized ore has been mined, so milling is confined principally to the sulfide ore. A typical analysis of sulfide ore is: silica (SiO2), 86.76 per cent; pyritc (FeS2), 2.75; ferric oxide (Fe2o3), 2.65; alumina (Al2o3), 6.91; lime (CaO), tr.; magnesia (MgO), 0.70; sp. gr., 2.7. Milling grade at present price of gold (137 shillings per ounce) varies from 3.5 to 8.5 dwt., with one mine milling ore as high as 16 dwt. The

Jan 1, 1935

By YANG TSANQ WOO

THE method of making coke that has been adopted at the Kaiping and other collieries in northern China resembles, to some extent, the familiar bee-hive oven process of the United States, except that a kiln with permanent sides is used instead of a closed oven, and the products of combustion are drawn off at the bottom, In building coke-kilns in China, two circular holes, 8 ft. 6 in. in diameter at the bottom and 13 ft. in diameter at the top, are excavated in the ground, both being .connected at the bottom by a flue as shown in Fig. 1. The sides and bottom of the kiln are lined with fire-bricks, and covered with a layer of fire-clay, and a rectangular opening, 6 in. by 8 in., connects the bottom of each kiln with the main flue. Around the edge of the hole, and overlapping the lining, is a wall of fire-brick extending .2 ft. 6 in. above the level of the ground. An open space 5 ft. wide is left in this wall, through which the coal is carried into the kiln and the resultant coke removed. This space, of course, is bricked up during the time that the coking operation is being carried on. The wall is pierced with nine flue-openings uniformly placed around the circumference, each intervening space in the wall being strengthened with a brick buttress, as is shown in Figs. 2 and 4. The floor of the kiln, as well as the main flue, is lined with fire-brick. Before charging the coal, it is first placed in shallow bamboo sieves, 2 ft. in diameter, and immersed in a trough 10 ft. long, and 3 ft. wide, fed with pit-water; in which it is washed by hand. Fig. 3 shows the manner in which the washing is done. From 25 tons of good " dust" coal, 22.5 tons of washed coal are obtained. When ready to charge the coal into the kiln a temporary cone-shaped flue of fire-wood and lump coal is first built to a

Nov 1, 1905

By R. Clare Coffin

The production of oil in the Rocky Mountain district, including southeastern New Mexico, increased from 33,048,630 bbl. in 1930 to 34,325,163 bbl. in 1931. This increase was due to production in New Mexico, which exceeded the 1930 figure by approximately 5,000,000 barrels. Total production by fields is given in Table 1. Exploration during 1931 resulted in the discovery of a new oil-producing horizon in the Big Muddy field in Natrona County, Wyoming, and ' the discovery of a new gas pool in the Powder Wash structure, Moffat County, northwestern Colorado. Gas was discovered also in the Frontier sands of the Bunker Hill dome, Carbon County, Wyoming, but no test has yet been made by which to determine the significance of this discovery. All other exploration which resulted in increasing the known reserves of oil and gas in the district was confined to drilling in partly outlined fields where known limits of production were extended. During the year two major gas pipe lines were completed in western Montana, and one in southwestern New Mexico was extended into Arizona. One new project involving the marketing of natural gas from Wyoming fields included the conversion of an existing oil line to a gas line to serve towns in southeastern Wyoming and western Nebraska. Colorado The decline of 132,501 bbl. in the production of oil in the Colorado fields during 1931 from the figure of 1930 is due to the natural decline of existing wells, partly offset by the increased production in the Greasewood area. New exploration was limited largely to northeastern Colorado, where attempts were made to find oil in areas adjacent to the Grease-wood field. Powder Wash, Moffat County.—The Ohio Oil Co. is to be credited with the discovery of a gas field in the Power Wash structure in Moffat County, Colorado. The initial well drilled in sec. 5-11-97 encountered a sand at a depth of 2152 ft. which produced 34,188,000 cu. ft. of gas on an open-flow test. The rock pressure was reported as 630 Ib.

Jan 1, 1932

By Alfred Beasley

LEAD-REFINING practice at the. Bunker Hill differs to some extent from that of other United States refineries using the Parkes process, in that the Bunker Hill-has reverted to a custom used years ago of making two kinds of skims, or crusts, in the desilverizing kettles. Also, this was the first refinery to adopt the liquation process for silver skims as developed in Australia. Both of these ideas were brought to the attention of the operator by H. S. J. Sommerset, in the summer of 1924, while he was visiting metallurgical plants in the United States, when he was general superintendent of the Broken Hill Associated Smelters Pty., Ltd., of Port Pirie, South Australia. Since Mr. Sommerset's visit, United States patents on the liquation process have been issued to George Kenneth Williams, of Port Pirie, South Australia. At the Bunker Hill, the lead bullion is conveyed from the blast furnaces to the refinery in brick-lined cast-steel pots, each having a capacity of 5 tons, by a 20-ton electric crane, to which is suspended a Fairbanks-Morse suspension-type scale on which the gross, tare and net weights are obtained. The bullion is poured from the small bullion pots into either one of two kettles of 105 tons capacity, and when a kettle is entirely filled the heavy dross is removed by skimming it into a 5-ton pot suspended by the crane. The crane operator becomes proficient in the manipulation and a kettle is skimmed in a very short time. After the kettle is skimmed clean the bullion is pumped to a kettle of the same size alongside, where the bullion is cooled until it has almost frozen. By using two kettles for the drossing operation, one to accumulate the bullion where the heavy dross is removed, and then pumping to a clean kettle comparatively free of hangings, etc., it is possible to reduce the copper content much lower than if only one kettle is used in the operation. The average yearly analysis of bullion is given in Table 1.

Jan 1, 1930

By S. Razi

Injection luminescence of single crystals of rare-earth-activated CdS was investigated. Crystals of CdS:Nd, CdS:Er, and CdS:Yb, grown by the vapor transport technique, were suitably etched and hetero-junctions of Cu2S-CdS were fabricated on one side of the CdS substrate by chemical reaction. The device was then heated to 200°C in an inert atmosphere for 5 min. Static V-I measurements show that at low voltages (V < 1 v) the current is controlled by the junction, while at higher voltages the bulk Properties of the CdS substrate effectively control the current. Because of the large thicknesses no negative resistance was found. Reverse breakdown voltage varied from 5 v, for junctions that were not heat-treated, to 100 v, for diodes that received the proper heat treatment. The rectification ratio, measured in the range of 2 to 10 v, varied from 300 to 3000. Capacitance- voltage measurements indicate a weak dependence of the junction capacity on applied voltage. The capacity was found to increase appreciably with room light illumination. The variation of capacitance with frequency is indicative of a p+-i-n structure. An open-circuit voltage of 0.4 v was measured under an illumination of 100 mw per sq cm. Under forward bias, the bluish-green edge emission characteristic of CdS was observed. No sharp rare earth emission line was observed, which is in contrast to our results using ZnS:Tb, where, under high-voltage excitation, the rare earth emission was dominat over the lattice emission. The absence of rare earth emission implies that either the nature of the rare earth ion is different at the het-erojunction than in the bulk or the probability of energy transfer to the rare earth ion is small. RARE earth elements are playing an increasingly important role in the Synthesis of materials for a variety of purposes, e.g., solid-state lasers, color television screens, and so forth. Interesting systems result when wide-band-gap photoconducting lattices are activated with rare earths. A study of the lumines-

Jan 1, 1969

By J. R. Campbell

It is the purpose of this paper to review somewhat in detail the literature on the subject that is extant, which ought to provoke considerable beneficial discussion. The value of 1 per cent. ash in blast-furnace practice was brought to the attention of the writer when he was connected with the U. S. Steel Corpn. Various groups of blast furnaces in the Pittsburgh district compiled a statement in which the average saving was about 6 c. per ton on pig iron for every 1 per cent. of ash reduction. Later, the same groups of furnaces, when materials had reached a higher price, compiled a statement in which there was a 30-cent saving on pig iron for every 4 per cent. ash reduction in the Pittsburgh district, which was equivalent to 7½ c. for every 1 per cent. ash reduction. In the Chicago district, on long freight hauls of coal and coke from the Pocahontas district, the set-up was 30 c. per ton of pig iron for every 2 per cent. ash reduction, or 15 c. for every 1 per cent. Some years ago, Ralph H. Sweetser, of the American Rolling Mill Co., presented a paper which provoked considerable comment.&apos; To get the matter again before this body a résumé of his computations is given below: Comparison of Pig Iron Costs Ash in Coal. Ash in CoKe, Fixed Carbon in Coke peR Ton OB PIG Iron peN Day, Per Cent. PeR CeNt. Coke. Per Cent. PIG IRon. Lb. Tons 6.00 8.70 89.80 1800 365.0 7.00 10.15 88.35 1860 353.2 Coke with 8.70 Per Cent. Ash Ore mixture, 4144 It). = 1.85 tons @ $5.50.............................. $10.17 Coke, 1800 lb. = 0.90 ton @ $6.50..................................... 5.85 Limestone, 1000 lb. = 0.50 ton @ $1.50................................. 0.75 Labor, $365 per day on 365 tons....................................... 1.00 Supplies and service, $250 per day...................................... 0.68 Overhead, $200 per day............................................... 0.55 Reserve for relining and depreciation................................... 1.00 Total............................................................. $20.00

Jan 1, 1931

By J. A. Herbst, G. E. Agar

The effect of fluid viscosity on the classification of solids in a liquid-solid cyclone was investigated. The separation size was found to be proportional to Additionally, it was found that the prediction of flow rate through a cyclone is dependent on a Reynolds criterion. Above a critical value, the flow can be predicted by a simple equation, whereas, below this value a variable orifice coefficient must be introduced. INTRODUCTION The solid-liquid cyclone is widely used as a device for classification, thickening, and heavy media separations. The more important variables and how they affect the performance of a cyclone are known and have been the subject of several investigations.&apos; In general, these studies have paid little attention to the viscosity and those which have, introduced it through Stokes settling considerations. Systems which contain appreciable amounts of swelling clays exhibit viscosities much greater than water, and in these systems the viscosity term becomes important in determining the separation size. The work described here was done to determine in a Newtonian system the dependence of separation size on viscosity. BACKGROUND The separation size for a cyclone classifier has been related to the parameters of the cyclone by an equation of the form: where a is probably between 1.3 and 1.5, ß is between 0.50 and 0.57, and 6 has a theoretical value of 0.5. where y has a value between 1.8 and 2.0. Although these relationships are empirical, equations that differ only in the exponents have been derived from theoretical considerations. Those interested in the origin of these equations are referred to some of the original work.6,7 MATERIALS AND PROCEDURE The laboratory apparatus used in this study is pictured diagramatically in Fig. 1. Feed slurry was pumped from an agitated 15-gallon plastic tank by a centrifugal pump driven by 3/4 hp motor. The static pressure of the feedstream and thus the pressure drop through the cyclone was measured on a gage located as close to inlet of the cyclone as possible. When samples were not being taken, overflow and

Jan 1, 1967

By Gilbert P. Moore

Petroleum operations in Bolivia are still limited to those of the subsidiaries of the Standard Oil Co. of New Jersey. Development work is being carried on at Sanandita and at Bermejo and testing operations in the north. Five wells have been completed at Sanandita. Wells 1 and 2 are producers, 3 and 5, which are north of 1 and 2, are poor wells, and well 4, to the south, was dry. In the Bermejo field, well 5 has just been completed. No information as to the production is obtainable. In the north one string was operated at each of the following locations: Machareti, Camatindi and Camiri. The well completed at Machareti during the year was a failure. The result of the others is not known. It is reported on good authority that a pipe line will be completed in 1931 to connect the Sanandita field with the Lomitas field in the Argentine. This will place Bolivia among the ranks of the producing countries of South America for the first time. This development indicates that some arrangement has been arrived at with the Argentine Government for the importation of Bolivian oil. During 1930 the Bolivian Government declared in effect the new Petroleum Law which had been expected for such a long time. One of the first acts of the military junta, which rose to power through a coup d&apos;état, was to cancel this law, so that Bolivian oil operations are still under the old law of 1921. One new local company was formed to exploit 1,500,000 hectares near the town of Cochabamba. The Bolivia Concessions, Ltd., which had a concession permitting the selection of 17,000,000 acres in eastern Bolivia, is reported to have failed in 1930 and is now being liquidated. Chile During 1930 the Chilean Government entered into a contract with an individual to explore in five distinct zones of the Republic. According to the contract, geologists must be at work there by May 1 of this year and a well must be started by the end of 1931. If the operations are

Jan 1, 1931

By R. Philip Hammond

MONAZITE has had a Cinderella-like history. Although nearly go per cent pure rare-earth compound (rare-earth phosphate) it was sought at first not for the rare earths but for the sake of a minor constituent-thorium. The thorium, essential for the Welsbach gaslight mantle, was present in only small quantities and the principal constituents, the rare earths, were largely discarded. Gradually, however, the rare earths have developed uses of their own and today have left the thorium far behind in value. OCCURRENCE Monazite was first produced commercially about 1886, in North Carolina, where it was collected in small sluices by farmers who found it in stream beds on their land. The deposits were later exploited on a larger scale, but were mostly abandoned in a few years, when monazite from Brazil came upon the market in far larger quantities. Domestic production ceased entirely in 1906. The Brazilian source is still active, together with Indian, Dutch East Indies, and Australian deposits. Several other localities in the United States have yielded monazite, but none of these has produced commercially as yet. Monazite occurs originally in pegmatites and gneisses, through which, unfortunately, it is scattered in highly dispersed form. All commercially useful deposits consist of transported monazite sands liberated by erosion and concentrated by the action of water, which has sluiced away lighter materials and concentrated the heavy (D = 5.0 to 5.2) grains of monazite, together with ilmenite, zircon, garnet, and other dense minerals. The Carolina deposits were in stream beds; most of the other deposits mentioned are on or near the seashore, where the action of the waves has served to concentrate the monazite. In most cases today, the sands are worked to obtain the ilmenite and zircon, as well as monazite. The minerals are separated by means of sluices, dry tables, and magnetic separators, and each is finally obtained nearly pure. No crushing or grinding is necessary. The concentrates are shipped in fiber bags. COMPOSITION OF MONAZITE As Table I illustrates, monazite is the anhydrous orthophosphate of the cerium [ ] group of rare-earth elements. A small amount of yttrium and terbium group phosphate is also present.* All the rare-

Jan 1, 1946