Search Documents

By R. O. Williams

The concept of biaxial pole figures which completely represent sheel textures is defined and an iterative least-squares solution given. The method has been applied to rolled copper, aluminum, and brass. The results show that the prior ideal textures are reasonably correct but incomplete. The major components in all three cases consist of a continuous range of orienta-tions roughly described as starting from (211) [111] continuing to (110) [112] to (110) [001], the details dif- THIS paper considers the problem of representing rolling textures in the most useful and comprehensible manner possible. A representation called a biaxial pole figure which completely represents such textures fering in all cases. For brass, in particular, the last part of the range is the most important. A minor cube component is established for the copper and aluminurn. The results were also analyzed by means of sets of three axial (inverse) pole figures to give similar, less-detailed results. The method of analysis is outlined. Such a representation is significantly less powerful than the biaxial method, but it has considerable utility in the calculation of anisotropic properties. is defined and an iterative least-squares solution is given. Such textures may be approximated by treating the principal directions as fiber axes to give three axial (inverse) pole figures. This representation is very useful for calculating anisotropic properties. New data for rolled copper, brass, and aluminum are given by both methods. In an axial pole figure the relative frequency or probability of a given physical direction (normally the

Jan 1, 1969

By T. Prof. Egleston

How to interpret the composition of rocks has been a question which has caused a great deal of discussion and investigation among geologists and chemists. It is evident that that analysis will give the clearest results, which will give the relative proportion of the different minerals composing the rock as well as the weight of their different constituents. This, however, is a very difficult matter, and in those rocks which seem to the naked eye entirely compact, like obsidian and other rocks of that class, appears to be impossible. Cordier, in the early part of the century, invented a process which is known as the " mechanical analysis of rocks," which is really a method of mechanical preparation, and consists in crushing the rock to a certain fineness, and then, by virtue of their density, washing out the different minerals, so as to make a mineralogical analysis, separating completely the different constituents of the rocks. In the hands of so skilful a man, this was a comparatively easy matter, and Cordier found no difficulty in ascertaining the mineralogical composition of a rock. The ultimate chemical composition was ascertained from the sum of the elements contained in the different materials. In the light of to-day, it is very easy to see that the complete chemical analysis of the rock does not necessarily lead to the explanation of its character. It has been so difficult, however, to have any other kind of analysis made that most chemical examinations have been made as ultimate, and not as mineralogical analyses. The panning out of the different minerals composing the rock, which are often very nearly of the same specific gravity, is so difficult that a person of ordinary mechanical skill is scarcely able to do it; consequently the mechanical analysis which Cordier proposed, and was able himself so skilfully to effect, has never been practiced to any extent. A school was formed in France consisting of a very small number of Cordier's followers, which, in face of the difficulty of acquiring the method, very soon died out as a school, though some of his most skilful followers are still living. The next important step in ascertaining their composition was to out the rock into transparent sections and examine the minerals with

Jan 1, 1875

By Robert H. Richards

OF the several professions-the chemist, the civil engineer, the mining engineer, the mechanical engineer-the courses of instruction, as arranged at the scientific schools, differ considerably as to the amount of practical information which the student is able to gain. The analytical chemist has facility for a very thorough review of the processes which he will be called upon to perform. The student in civil engineering by his field practice learns the use of his tools and the art of taking field-notes. The mechanical engineering student is in the vicinity of machine-shops, which he can visit, and at which he can work. The student in mining engineering has no such advantages. The mines are at a distance, and the railroad fare to get to them is oftentimes an insuperable difficulty. The aim of these laboratories is essentially to give to the student in mining and metallurgy a chance to study on a small scale the practical parts of his profession. We cannot, in a small laboratory, build a mine to timber, to work, and to survey; we cannot make artificial quicksands and other impediments to mining. In short, we cannot study exploration; but we can study the mechanical preparation and the subsequent smelting of ores. Before presenting the plan of these laboratories it may be interesting to indicate the progress of the idea from its beginning. During the summer of 1870 President Runkle visited the mines of Colorado, and while there, conceived the idea of making an expedition with the mining students to some of the Western mining regions. He talked over the scheme with many railroad and mining men, and everywhere received encouragement. In the summer of 1871 the Institute party visited the mines of Colorado, and spent six weeks in taking notes of them. President Runkle here conceived the idea of building up a mining and metallurgical laboratory ; and by the aid of Booth & Co. of San Francisco, a stamp-mill was obtained, with the Washoe silver-working apparatus. During the year

Jan 1, 1873

By Howard R. Hughes

In drilling for water and oil to reasonable depths through the generally soft yielding clay and sand formation of the Coastal Plain of Texas, Louisiana, and Mississippi, the rotating method of drilling was adopted, principally on account of the easy and quick penetration, and the low cost of the drilling plant. In favorable ground, free of heavy gravel and rock strata, as much as 1,600 ft. has been drilled in less than 36 hr., although such performances were of course rare. Hydraulic rotary drilling, or, as it is now called, rotary drilling, was used in the above States as early as 1880. The plant consisted of an ordinary derrick, a 25-h.p. boiler, a small hoist, a steam pump, and a water swivel with hose attachment, and an ordinary flat diamond-pointed bit. The successful drilling in of a phenomenal oil well by this process on Spindletop, near Beaumont, Texas, on Jan. 10, 1901, and the ascertained impracticability of drilling subsequent wells in the same locality by other methods (owing principally to heavy quicksand under pressure from below), brought rotary drilling into great prominence, practically to the exclusion of any other process throughout the Coastal Plain, and later on elsewhere. The method, as its name implies, involves the rotation of a pipe by means of machinery placed on the derrick floor. A drill bit attached to the lower end cuts a clearance for the drill pipe, with much the same motion and effect as an auger. Water forced through the drill pipe by means of a pump, and escaping through the bit, removes the cuttings and returns to the surface outside the drill pipe. In this manner the hole is kept open, permitting the drill stem to rotate freely. The pressure of the column of muddy water holds up the walls of the hole until it has been cased. Practically all the wells of the Gulf coast region, numbering nearly 10,000, have been drilled with this system. During the last five years its use has been extended to many other States and countries.

Jan 1, 1915

By Eugene F. Poncelet

This paper attempts to analyze the phenomena involved in the fracture of brittle solids by simple compression. Glass squares standing on edge, and compressed between two parallel steel jaws, developed jagged fractures, roughly parallel to the compression. Polarized light disclosed the presence of high local stress concentrations indicating poor contact all along the contact surfaces with the steel jaws. Teszar has shown that partial contact between the jaws and such a compressed solid causes tensile stresses in the free surfaces of the solid normal to the compression. Furthermore, Scoble has shown that in brittle solids fractures are caused by, and develop normally to, a sufficient tensile stress. It follows that such "partial-contact" cracks must be expected. With optically flat jaws and specimens, no "partial-contact" cracks developed. Instead, very smooth cracks vertical to the compression appeared 'upon release of the pressure. Investigation showed that the friction with the rigid steel opposed the return of the glass to its original width, after creeping on the steel as compression built up, thus setting up tensile stresses in the glass surfaces. It was not found possible to eliminate these "release" cracks. Compressed to destruction, such specimens flew to dust. A Microflash photograph taken during the explosive disintegration revealed: (I) oblique parallel fragmentation cracks, 30" off the direction of the compression; (2) transverse forking fragmentation cracks, normal to the former; (3) release cracks parallel to the compression; (4) a disintegration cloud. Given a distribution of submicroscopic cracks of random orientation throughout the glass, Griffith has shown the highest tensile stresses to be located at the tip of the cracks 30" off the direction of the compression. Although the preexistence of such cracks or flaws in unstressed glass is doubtful, they can be generated by the distorting forces set up by the compression itself. Atoms, in a structure held together by Morse-type forces or bonds, have under tension both a stable and an unstable state-of equilibrium. The difference in energy level between these two states is a function of the tension, and this difference must be borrowed from the thermal energy level of the bonds to reach the unstable state and result in a broken bond. As the fraction of the bonds having at any instant a sufficient thermal energy level is a known function of that level, it is possible to determine, in function of the prevailing tension, the fraction of the bonds that are broken. Upon breaking of the bond uniting two atoms at the tip of an advancing crack, the two atoms accelerate away from each other, causing in the solid propagation of a

Jan 1, 1944

By Eugene F. Poncelet

This paper attempts to analyze the phenomena involved in the fracture of brittle solids by simple compression. Glass squares standing on edge, and compressed between two parallel steel jaws, developed jagged fractures, roughly parallel to the compression. Polarized light disclosed the presence of high local stress concentrations indicating poor contact all along the contact surfaces with the steel jaws. Teszar has shown that partial contact between the jaws and such a compressed solid causes tensile stresses in the free surfaces of the solid normal to the compression. Furthermore, Scoble has shown that in brittle solids fractures are caused by, and develop normally to, a sufficient tensile stress. It follows that such "partial-contact" cracks must be expected. With optically flat jaws and specimens, no "partial-contact" cracks developed. Instead, very smooth cracks vertical to the compression appeared 'upon release of the pressure. Investigation showed that the friction with the rigid steel opposed the return of the glass to its original width, after creeping on the steel as compression built up, thus setting up tensile stresses in the glass surfaces. It was not found possible to eliminate these "release" cracks. Compressed to destruction, such specimens flew to dust. A Microflash photograph taken during the explosive disintegration revealed: (I) oblique parallel fragmentation cracks, 30" off the direction of the compression; (2) transverse forking fragmentation cracks, normal to the former; (3) release cracks parallel to the compression; (4) a disintegration cloud. Given a distribution of submicroscopic cracks of random orientation throughout the glass, Griffith has shown the highest tensile stresses to be located at the tip of the cracks 30" off the direction of the compression. Although the preexistence of such cracks or flaws in unstressed glass is doubtful, they can be generated by the distorting forces set up by the compression itself. Atoms, in a structure held together by Morse-type forces or bonds, have under tension both a stable and an unstable state-of equilibrium. The difference in energy level between these two states is a function of the tension, and this difference must be borrowed from the thermal energy level of the bonds to reach the unstable state and result in a broken bond. As the fraction of the bonds having at any instant a sufficient thermal energy level is a known function of that level, it is possible to determine, in function of the prevailing tension, the fraction of the bonds that are broken. Upon breaking of the bond uniting two atoms at the tip of an advancing crack, the two atoms accelerate away from each other, causing in the solid propagation of a

Jan 1, 1944

By E. V. Foran

TheRe are many factors which control the ultimate production of oil and gas from a producing formation and the rate at which this production is obtained from any of the producing wells in the formation. The most important of these, and the one over which the greatest control can be exercised, is the differential pressure existing between the formation and the well bore. In producing any well by means of the gas-lift, it may be possible to change the flow tubing in a number of ways or vary the volume of circulating gas or air used for flowing the well, but if these operations, regardless of their magnitude, do not change the differential pressure between the producing sand and the well bore, they will in no way change the production of the well. If this statement is accepted as a fact, then all gas-lift or air-lift installations should be designed with but one object in view; namely, a means by which we can economically control very wide ranges of differential pressures between the formation and the well bore. Factors of Production In gas-lift production from any given formation, there are four major factors which govern the magnitude of the differential: (I) the depth of the well; (2) type and size of flow tubing; (3) volume of the circulating air or gas, and (4) physical properties of the oil-gas mixture after it has reached the well. The first of these factors is uncontrollable and does not vary. The other three are controllable within certain limits. The degree to which the last three factors can be controlled will cntircly govern the length of life of the well while on the lift, the lifting cost, and the daily production. It will also govern to some extent the ultimate production from the wells or leases producing by this method. These four factors will be discussed in detail in another part of this paper. Before proceeding further, a review of the present general practice in Texas, elsewhere than in the Gulf Coast region, will be given.

Jan 1, 1928

By Thomas Leonard Watson

Sulphide ore-bodies of more or less lenticular shape occurring in metamorphic crystalline schists, gneisses, and slates, and conforming closely in strike and usually in dip to the inclosing rock, have been recognized and described along the Atlantic seaboard from Quebec to Alabama. The ore-bodies do not entirely conform, in all cases, to the structure of the inclosing schists, but they sometimes cut across the foliation in dip, though conforming more closely with the direction of strike. In composition the principal sulphide mineral is usually py-rite or pyrrhotite, or both, accompanied by copper, frequently gold, and almost always some sphalerite and galenite. Other metallic ores are, so far as these sulphide bodies have been investigated, less common; silver is not uncommon, and in some of the pyrrhotite masses nickel is present in quantity sufficient to be commercially valuable. Cobalt frequently accompanies the nickel, usually in smaller amount, and the two vary much in relative proportion. Quartz and calcite are probably the most common of the non-metallic minerals. A number of silicate minerals are frequent representatives in one place or another ; garnet, am phi-bole, biotite, pyroxene, zoisite and others. The sulphide bodies of Virginia, comprising both pyrite and pyrrhotite, are among the most extensive along the Atlantic seaboard. Among the pyrite bodies may be mentioned the well-known and extensively worked mines of Louisa and Prince William counties, located on the main pyrite belt (A, Fig. 1) of the middle and northern, eastern Piedmont region in Virginia, and among the pyrrhotite bodics is the famous " Great Gossan Lead" (13, Fig. 1) of the Floyd-Carroll-Grayson coun-

Jan 1, 1908

By W. TRINKS

RAPID progress has been made in the automatic control of open-hearth furnaces in the past few years and many firms today\supply such control apparatus. It is somewhat surprising that so little was heard about open-hearth control up to about, 1928, and that thereafter the practice of automatically controlling open-hearth furnaces spread very rapidly. Before discussing the reasons for this it may be advisable to list the quantities that can be controlled. One of the easiest quantities to be controlled in the open-hearth furnace is pressure. The reasons for controlling it are plain. If there is excess pressure in the furnace, products of combustion leak out around .the .door and through all the cracks in the brick-work. The stability of the piers between the doors is seriously endangered, and front wall repairs become frequent. Furthermore, hot gases are lost that might be usefully employed in heating the checkerwork. If there is a slight vacuum in the furnace, cold air entering through the doors and cracks cools the interior, slowing down the reactions and making it impossible to secure the highest degree of preheat from the checkerwork.

Jan 1, 1931

By Gray L. L., Max Littlefield, Godbold A. C.

The West Edmond pool of Central Oklahoma, a limestone reservoir, has an area in excess of 29,000 acres and as of Sept. 15, 1946, had produced 53 million barrels of oil from 731 wells at an average depth of 6900 ft. Water has encroached into the reservoir along the west side of the pool and although the area of water invasion is large the net volume of water influx is small, because encroachment has been primarily into a fracture system. The most significant part of this study concerns the character of the Hunton reservoir. Geological study of cores of the producing section was made to supplement core-analysis data. It was determined that approximately 90 pct of the pore volume was contained in intergranular or sand-like porosity and 10 pct in fractures (intermediate porosity). The porous limestone is divided into blocks by the fractures, although in the strongly dolomitic parts of the producing section, fractures are less well developed. The low-permeability intergranular porosity, largely subsidiary to the high-permeability fractures, will produce oil into the fractures by evolution of solution gas. The fractures in effect serve as drainage channels for production of oil from the inter-granular porosity. Because of such a large difference in permeabilities of the two com-ponents, a high degree of by-passing will occur, and, accordingly, the economics involved in undertaking full-scale high pressure gas injection operations have been seriously questioned. Introduction The West Edmond Hunton pool, which covers portions of Canadian, Logan, Oklahoma, and Kingfisher Counties in Central Oklahoma, is the largest reservoir producing oil from a limestone in the state. The total area of the pool comprises about 29,240 acres and development is considered to be essentially complete. In all, 731 producing wells have been completed in the Hunton reservoir at an average depth of approximately 6900 ft, and have yielded a cumulative oil production in excess of 53 million barrels as of Sept. 15, 1946. In addition to wells completed in the Hunton limestone, 21 wells have been completed in the Bartlesville sand at a depth of approximately 6500 ft, which have produced a total of 730,000 bbl of oil. One small producer has been completed in the Cleveland sand at a depth of 5700 ft. However, a study of only the Hunton limestone reservoir will be presented in this paper. The most significant phase of this study concerns the special type of geological core examination that was made in an effort to ascertain the type and degree of porosity in the rock in accordance with lithologic types. Results of this geological study showed the west Edmond pool to be of such a complex nature as to appreciably affect the behavior normally associated with homogeneous reservoirs. Recognition of this condition in the

Jan 1, 1948

By Max Littlefield, Godbold A. C., Gray L. L.

The West Edmond pool of Central Oklahoma, a limestone reservoir, has an area in excess of 29,000 acres and as of Sept. 15, 1946, had produced 53 million barrels of oil from 731 wells at an average depth of 6900 ft. Water has encroached into the reservoir along the west side of the pool and although the area of water invasion is large the net volume of water influx is small, because encroachment has been primarily into a fracture system. The most significant part of this study concerns the character of the Hunton reservoir. Geological study of cores of the producing section was made to supplement core-analysis data. It was determined that approximately 90 pct of the pore volume was contained in intergranular or sand-like porosity and 10 pct in fractures (intermediate porosity). The porous limestone is divided into blocks by the fractures, although in the strongly dolomitic parts of the producing section, fractures are less well developed. The low-permeability intergranular porosity, largely subsidiary to the high-permeability fractures, will produce oil into the fractures by evolution of solution gas. The fractures in effect serve as drainage channels for production of oil from the inter-granular porosity. Because of such a large difference in permeabilities of the two com-ponents, a high degree of by-passing will occur, and, accordingly, the economics involved in undertaking full-scale high pressure gas injection operations have been seriously questioned. Introduction The West Edmond Hunton pool, which covers portions of Canadian, Logan, Oklahoma, and Kingfisher Counties in Central Oklahoma, is the largest reservoir producing oil from a limestone in the state. The total area of the pool comprises about 29,240 acres and development is considered to be essentially complete. In all, 731 producing wells have been completed in the Hunton reservoir at an average depth of approximately 6900 ft, and have yielded a cumulative oil production in excess of 53 million barrels as of Sept. 15, 1946. In addition to wells completed in the Hunton limestone, 21 wells have been completed in the Bartlesville sand at a depth of approximately 6500 ft, which have produced a total of 730,000 bbl of oil. One small producer has been completed in the Cleveland sand at a depth of 5700 ft. However, a study of only the Hunton limestone reservoir will be presented in this paper. The most significant phase of this study concerns the special type of geological core examination that was made in an effort to ascertain the type and degree of porosity in the rock in accordance with lithologic types. Results of this geological study showed the west Edmond pool to be of such a complex nature as to appreciably affect the behavior normally associated with homogeneous reservoirs. Recognition of this condition in the

Jan 1, 1948

By Frank S. McKenna, Myron A. Pugacz, Clarence E. Jackson

THE notched-bar impact test has proved worth while in certain applications as a test for control of the quality or the heat- . treatment of steel. In view of the serious thought that even so simple a test as the tensile test, has evoked during the past years, it is not surprising that the notched- bar impact test should have inspired much experimental work. The correlation of the great number of data has not been successful, although steady progress has been made toward a better understanding of this test. Progress has been made, especially, in the isolation of the effects of the many variables that control the results. The stress system imposed on a specimen with a notch is so complicated and un- predictable that no simple evaluation of the test has been possible. Because of this uncertainty, many engineers hesitate to use the notched-bar impact test, and this attitude may well continue until a better understanding of the effects of the variables in the test are available. Without doubt, any additional data that may be presented should be accompanied by as complete a description of the details of test as possible, so that it may be added to the general fund of information that is to serve as the basis for the theory of the notched-bar impact test. The many factors that may control the test results have been pointed out repeatedly. The importance of the effect of the type and dimensions of the specimen has been recognized. Most of the work reported by American investigators has been limited to small- size (Charpy) specimens tested as a simple beam; two types of notches (Fig. I) have been commonly used. Considerable data have also been presented by many investigators using a small specimen tested as a cantilever beam; this commonly being called the Izod test. Here, however, a shear component of stress makes the stress system even mare complex than that present in the simple beam type of test, hence a critical analysis is difficult. Much work has also been reported by investigators using the tension type of specimen. A second variable that must be con- trolled is the testing temperature. An indication that the tests were performed at room temperature is not sufficient, since in many steels a variation of a few degrees in the actual testing temperature may be sufficient to give an entirely different range of results. Other factors. such as the com- position and condition of the material being tested and the speed of test, should also be considered. Many investigators have contributed data and theoretical discussions on the problems encountered in notched-bar test-

Jan 1, 1944

By Avnulf Muan, Egil Aukrust

The activity-composition curve for cobalt oxide in (Co,Fe)304 solid solutions with spinel-type stmcture has been determined experimentally by studying the equilibrium between the spinel phase and a coexisting cobaltowüstite phase, "(Co,Fe)O", at 1200°C. A large negative deviation from ideal behavior prevails in the spinel at low cobalt oxide concentrations and a positive deviation at high cobalt oxide concentrations. The activity-composition curve for iron oxide in the solid solution is determined from the above curve by integvation of the Gibbs-Duhem equation along the join Co3O4,-Fe3O4. The standard free energy of formation of cobalt ferrite, CoFe2O4, from the oxide components CoO and Fe2O3 is calculated to be -8.2 kcal. ThERMODYNAMIC properties of (CO,Mn)3O4 solid solutions with spinel-type structure have been presented recently.' The present paper deals with similar relations in another spinel solid-solution phase, that represented by the system Co3O4-Fe3O4. The principles involved in measurements and calculations of thermodynamic properties for the system Co3O4-Fe3O4 are analogous to those used and discussed in detail in the work on (CO,Mn)3O4. A (CO,Fe)3O4 solid solution coexists in equilibrium with a (Co.Fe)Ot solid solution over a considerable Here acOo1.33 and aao are the activities of cobalt oxide in the spinel and the oxide solid solutions, respectively, pO2, is the oxygen pressure of equilibration, and pb, is the oxygen pressure at which CoO and CosO4 coexist in equilibrium in the binary system Co-O at the same temperature. The activity-com position curve for cobalt oxide in the (Co,Fe)O solid solution in contact with metal has been determined in a previous investigation by the present authors.' The system shows a small positive deviation from linear behavior. Because of the large defect concentration in wiistite and in (Co,Fe)O solid solutions, one cannot assume that the activity-composition relations in the oxide phase coexisting with a spinel phase at relatively high oxygen pressures are the same as those prevailing in the oxide solid solution coexisting with metal. However, a Gibbs-Duhem integration over the ternary Co-Fe-0 solution can be used to determine activities of cobalt and iron, and hence of CoO and FeO, from a knowledge of the oxygen potentials. Several papers have dealt with the subject of application of the Gibbs-Duhem equation to multi-component systems. 3-6 In the present case, it was

Jan 1, 1964

By H. H. Reamer, B. H. Sage

Attempts have been made to predict the volumetric and phase behavior of naturally occurring hydrocarbon mix-turesl-6 but these methods have not been extended to the higher pressures and tem-peratures that are currently encountered in some producing formations. Furthermore, the methods of prediction at present avail-able have not been tested in a sufficient number of cases to ensure their applica-bility to all naturally occurring hydrocar-bon mixtures, even at the lower pressures and temperatures. For these reasons the behavior of a number of hydrocarbon mix-tures from a field in which the subsurface pressures are above 4500 lb. per sq. in.t and the temperatures are in the neighbor-hood of 250°F. was investigated. Method The objective of this program was to determine the volumetric behavior of ma-terial as it existed in the reservoir as a function of pressure, temperature and com-position. Strictly speaking, this cannot be accomplished in any simple fashion. How- ever, the variations in composition that are encountered within a producing reservoir may be approximated roughly by means of mixtures made up of two arbitrarily chosen constituents. Experience indicates that the liquid and gas phases from a high-pressure gas trap afford a simple source of material for this purpose. Throughout this discus-sion the samples of the gas phase and liquid phase from the production trap will be called the "trap-gas sample" and the "trap-liquid sample," respectively. The volumetric behavior of both of the trap samples was determined throughout the temperature interval between 100" and 250°F. at pressures up to 5000 lb. per sq. in. In addition, the behavior of eight different mixtures containing varying proportions of the two trap samples was studied throughout the same temperature and pressure intervals. The experimental results yielded information concerning the specific volume of the material as a function of pressure, temperature and the relative quantity of the trap samples. The relative amount of each of the paraffin hydrocarbons of lower molecular weight than n-hexane was determined for each of the trap samples. In addition, the specific weight, viscosity and average molecular weight of the hexanes-and-heavier fraction of the trap-liquid sample were determined as well as similar information for each of five fractions separated from this material by distillation. From these data the weight fractions of each of the components from methane through pentane were determined for the trap samples and eight systematically chosen mixtures. Materials The gas and liquid samples were obtained from the production trap of a well in the Rio Bravo field in California during the fall of 1939. Information concerning the condi- 70

Jan 1, 1941

By H. H. Reamer, B. H. Sage

Attempts have been made to predict the volumetric and phase behavior of naturally occurring hydrocarbon mix-turesl-6 but these methods have not been extended to the higher pressures and tem-peratures that are currently encountered in some producing formations. Furthermore, the methods of prediction at present avail-able have not been tested in a sufficient number of cases to ensure their applica-bility to all naturally occurring hydrocar-bon mixtures, even at the lower pressures and temperatures. For these reasons the behavior of a number of hydrocarbon mix-tures from a field in which the subsurface pressures are above 4500 lb. per sq. in.t and the temperatures are in the neighbor-hood of 250°F. was investigated. Method The objective of this program was to determine the volumetric behavior of ma-terial as it existed in the reservoir as a function of pressure, temperature and com-position. Strictly speaking, this cannot be accomplished in any simple fashion. How- ever, the variations in composition that are encountered within a producing reservoir may be approximated roughly by means of mixtures made up of two arbitrarily chosen constituents. Experience indicates that the liquid and gas phases from a high-pressure gas trap afford a simple source of material for this purpose. Throughout this discus-sion the samples of the gas phase and liquid phase from the production trap will be called the "trap-gas sample" and the "trap-liquid sample," respectively. The volumetric behavior of both of the trap samples was determined throughout the temperature interval between 100" and 250°F. at pressures up to 5000 lb. per sq. in. In addition, the behavior of eight different mixtures containing varying proportions of the two trap samples was studied throughout the same temperature and pressure intervals. The experimental results yielded information concerning the specific volume of the material as a function of pressure, temperature and the relative quantity of the trap samples. The relative amount of each of the paraffin hydrocarbons of lower molecular weight than n-hexane was determined for each of the trap samples. In addition, the specific weight, viscosity and average molecular weight of the hexanes-and-heavier fraction of the trap-liquid sample were determined as well as similar information for each of five fractions separated from this material by distillation. From these data the weight fractions of each of the components from methane through pentane were determined for the trap samples and eight systematically chosen mixtures. Materials The gas and liquid samples were obtained from the production trap of a well in the Rio Bravo field in California during the fall of 1939. Information concerning the condi- 70

Jan 1, 1941

By E. W. Filer, R. P. Smith, L. S. Darken

The solubility of nitrogen gas in purified iron and low alloy steels is determined for the y region (930° to 1350°C). The diffusivtiy of nitrogen is estimated from the rate of approach to equilibrium. The investigation of aluminum-killed steels, held in nitrogen, discloses precipitation of aluminum nitride, the solubility of which is determined. ALTHOUGH several investigations of the solu-bility of nitrogen gas in y iron have been reported, all have made use of the method adopted by Sieverts in his classic work, whereby the solubility is determined by the pressure or volume change of the gas. The agreement between different investigators* is rather poor, particularly as compared to the self-consistency of results of several individual investigators. The present report represents a portion of our investigation of the equilibrium of nitrogen and nitrogenous atmospheres with iron and steels. The method adopted in this temperature region (910" to 1400°C) consists of holding the specimen in gaseous nitrogen, quenching (or cooling), and determining the nitrogen content by direct analysis (solution in acid followed by distillation and titra-tion of the ammonia).** Up to 1050°C a 20 in. vertical wire-wound (Kan-thal) furnace was used; this was wound in three sections so that by proper adjustment of relative currents, and use of a modulator1 and a commercial controller (using a chromel-alumel control couple), a zone almost 6 in. long could be maintained uniform within a few tenths of a degree. Since the temperature coefficient of the nitrogen solubility is low, the full precision was not utilized and a variation of l° to 2" was tolerated; a variation of a similar amount also occurred occasionally between the beginning and end of the experiment. At higher temperature a vertically mounted, tubular Globar furnace and control unit was used; the zone of uniformity (l° to 2"C) was here limited to about 2 in.; fluctuations with time were comparable to those in the wire-wound furnace. Reported temperatures were measured by use of a platinum-platinum-rhodium thermocouple, which was frequently com- pared with a similar standard couple which was calibrated at the gold and palladium points and also compared with one certified by the Bureau of Standards; error from this source is believed to be less than 1 "C. Nitrogen gas from a commercial cylinder was mixed with slightly over 1 pct H by use of a gas mixer described previously.' This mixture was passed over hot copper and through ascarite and phosphorus pentoxide to remove oxygen and water vapor. The purified gas contained 1.05 pct H. This procedure was adopted to prevent the formation on the specimens of oxide film, which is well known to be nearly impervious to nitrogen; its success was attested by

Jan 1, 1952

By Alfred R. Powell

Late in 1944 a group of petroleum and coal technologists was organized in Washington under the sponsorship of the Petroleum Administration for War and the U. S. Bureau of Mines. This group, known as the Technical Oil Mission, was placed under the authority of the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff, which was then promoting the organization of other missions to be sent to Germany to obtain technical information regarding various industries in that country. The objective of the Tehnical oil Mission was to obtain technical data on German production of synthetic oil from coal and all other commercial practices and research projects connected with the oil industry. The primary purpose was to obtain such data as were immediately essential to assist the war against Germany and Japan, with secondary emphasis on technical information that would assist American industry after the end of the war. since oil-production facilities in Germany and the occupied countries controlled by Germany were the top targets for strategic bombing, the Technical Oil Mission was the first group under the Technical Induslrial Intelligence Com,mittee to enter Germany. A few members of the group flew to London in February 1945 and the majority of the remainder followed in March. In London they were joined by an equal number of British investigators and the combined mission was then sent into Germany under the authority of the Combined Intelligence Objectives Subcommittee (CIOS). A summary of the more important information gained by this combined British and American mission is presented below. German Oil Production The oil available to Germany, both natural and synthetic, and including production from occupied countries, reached a peak in late 1943 and early 1944 Production at this time was at the rate of 1,200,000 metric tons Per month, equivalent to 100,000,000 bbl. per year, or about 7 per cent of the wartime production in the United States. Of this production, jo per cent was crude oil from Romania and Hungary, 12 Per cent was crude oil from Germany itself, including Austria, 9 per cent cumprised coal-carbonization products, that is, tar and light oil, and only the remaining 29 per cent was synthetic liquid fuel made from coal or tar. Synthetic liquid fuel made in Germany was equivalent therefore to less than 2 per cent of wartime production of crude oil in the United States. The success of the strategic bombing campaign against German oil-production facilities is demonstrated by the fact that by September 1944 the Ploesti fields of Romania and much of the syrlthetic oil production had been eliminated, so that the amount of oil available to the German war machine was only 25 per Cent of the peak qualltity mentioned above. By early 1945, when the combined British and American oil mission was entering

Jan 1, 1947

By Alfred R. Powell

Late in 1944 a group of petroleum and coal technologists was organized in Washington under the sponsorship of the Petroleum Administration for War and the U. S. Bureau of Mines. This group, known as the Technical Oil Mission, was placed under the authority of the Technical Industrial Intelligence Committee of the Joint Chiefs of Staff, which was then promoting the organization of other missions to be sent to Germany to obtain technical information regarding various industries in that country. The objective of the Tehnical oil Mission was to obtain technical data on German production of synthetic oil from coal and all other commercial practices and research projects connected with the oil industry. The primary purpose was to obtain such data as were immediately essential to assist the war against Germany and Japan, with secondary emphasis on technical information that would assist American industry after the end of the war. since oil-production facilities in Germany and the occupied countries controlled by Germany were the top targets for strategic bombing, the Technical Oil Mission was the first group under the Technical Induslrial Intelligence Com,mittee to enter Germany. A few members of the group flew to London in February 1945 and the majority of the remainder followed in March. In London they were joined by an equal number of British investigators and the combined mission was then sent into Germany under the authority of the Combined Intelligence Objectives Subcommittee (CIOS). A summary of the more important information gained by this combined British and American mission is presented below. German Oil Production The oil available to Germany, both natural and synthetic, and including production from occupied countries, reached a peak in late 1943 and early 1944 Production at this time was at the rate of 1,200,000 metric tons Per month, equivalent to 100,000,000 bbl. per year, or about 7 per cent of the wartime production in the United States. Of this production, jo per cent was crude oil from Romania and Hungary, 12 Per cent was crude oil from Germany itself, including Austria, 9 per cent cumprised coal-carbonization products, that is, tar and light oil, and only the remaining 29 per cent was synthetic liquid fuel made from coal or tar. Synthetic liquid fuel made in Germany was equivalent therefore to less than 2 per cent of wartime production of crude oil in the United States. The success of the strategic bombing campaign against German oil-production facilities is demonstrated by the fact that by September 1944 the Ploesti fields of Romania and much of the syrlthetic oil production had been eliminated, so that the amount of oil available to the German war machine was only 25 per Cent of the peak qualltity mentioned above. By early 1945, when the combined British and American oil mission was entering

Jan 1, 1947

By John R. Green

ROTARY kilns, varying in construction, are used in a variety of processes. Products differ and operating conditions vary according to economic requirements. All of these variables influence the degree of instrumentation and type of control necessary or profitable to install. Products fired in rotary kilns are the results of combined temperature and time treatment and the interrelation of these two factors should be kept constantly in mind in the perusal of this paper. MEASUREMENTS OF KILN TEMPERATURE The securing of proper temperatures within the rotary kiln, either of the charge or of the kiln lining in the high fire zone, are basic objectives of kiln operation; therefore the measurement of these high-temperature conditions merits first consideration.. For these measurements, radiation pyrometers, properly designed and protected, have proved adequate, particularly where records or automatic control are desired, while optical pyrometers may serve as portable indicators. Light-sensitive devices or photoelectric cells in this service are capable of producing records as well as certain forms of automatic control. High-temperature measuring devices for rotary-kiln work should have the measuring unit protected from dust, as a continued accumulation of deposit would lower the readings. Fig. I shows a typical application of radiation equipment to a rotary kiln, mounted far enough away from the sighting hole through the kiln hood to be protected from puffs or stingouts and with a sighting tube having a series of settling chambers, to prevent dust from reaching the lens. Although dust conditions inside the kiln itself usually fluctuate considerably and have their effect upon the readings at that moment, such effects are not cumulative and show as a continuous fluctuation in the temperature indicated, provided the radiation unit and recorder are responsive to such slight and rapid temperature fluctuations. The ambient temperature to which a measuring unit is subjected fluctuates from possibly o° to over 200°F., therefore these changes should have no effect upon the final reading or upon the life of the measuring unit. A very narrow sighting angle is desirable, so that measurement of temperature may be made as far as possible into the high fire zone without. effect of the flame temperature. There should be some sighting means on the measuring unit, so that the proper field may be viewed. Measurement of wall temperature taken at a point where the charge has just left the wall is less affected by dusting conditions than when taken elsewhere. Factors Influencing Temperature Table I gives an outline of the factors that produce kiln temperatures and com¬ments on the possibility of measurement and control. Of greater number and of varied influ¬ence are the factors that control when, where and how the heat is delivered to the kiln, the type of flame and the rate of

Jan 1, 1941

By G. W. Imholz

The effect of new discoveries and development of other pools recently discovered is reflected in the increase in production from 586,000 bbl. during 1940 to 758,000 bbl. during 1941 in Coleman County. The States Oil Company's No. I Hudson, Coleman County, was the discovery well of the Silver field, with a total depth of 3540 ft.; initial production, 10,000,000 cu. ft. of dry gas and 60 bbl. of oil per day from the Gray sand, topped at 3482 ft. The first well drilled in the new Jim Ned field was the Merry Bros. and Perini No. I Greer, also in Coleman County. It had a total depth of 3937 ft. and an initial production of 152 bbl. of 42" gravity oil in 6 hr., through I-in. choke, from Gray sand encountered from 3909 to 3937 feet. J. E. Farrell's No. I Rose, Haskell County, was a new discovery, around which no additional wells have been drilled. Total depth was 3002 ft., plugged back to 2780 ft. to test an oil sand encountered from 2663 to 2685 ft., which when perforated with 76 shots at that depth was good for 85 bbl. of 40" gravity oil. In Fisher County, General Crude drilled its No. 12 Flanagan to a total depth of 6746 ft. After plugging back to 4578 ft. to test a sand encountered from 4515 to 4528 ft. it was abandoned as a dry hole. The top of the Ellenburger was reported as 6094 feet. Interest in Jones County continued unabated, largely through the development of the Wimberly pool in the southern part of the county, where five Cisco sands are producing. At present the pool has been defined on the south and the southwest. The structure has 170 ft. of closure; the lower limestone pays producing on top of the structure and the fist pay encountered, the Akard sand, producing on the flanks of the structure. Five deep wells were drilled in Stonewall County (H. and T.C. survey)—the Shell Oil Company's No. I-A Patterson, in block D, with a total depth of 6827 ft., dry and abandoned; the Shell Oil Company's No. I Rutherford, block I, with a total depth of 6239 ft., dry and abandoned; the Leader Oil Company's No. I Bilberry, block D, with a total depth of 5700 ft., dry and abandoned; Forest Development Company's No. 2 Boyd, block D, with a total depth of 4753 ft., dry and abandoned; and the Hunter et al. No. I Boyd, block D, total depth 4757 ft., dry and abandoned. J. E. Farrell drilled his No. I Tipton south of a well that produced from a Strawn sand for some time, to a total depth of 5202 ft., where it was abandoned. The well is in the southwest corner of sec. 43, block 19, T. and P. survey, Nolan County.

Jan 1, 1942