Search Documents

By C. A. Stetefeldt

In May and June, 1885, I was engaged in examining the goldores of Las Minas, in the State of Vera Cruz, Mexico, with a view of finding a cheap and efficient method for extracting the gold. The following minerals could be plainly seen in the ore : magnetite, pyrites of iron, pyrites of' copper, quartz, and garnet. Neither galena nor zinc-hlende mere visible, but the ore contained a trace of lead, and in some samples of ore from the Muertos mine, 1.19 per cent. of zinc mas found. Antimony and arsenic were not present. Native gold could scarcely be seen in specimens of' the ore, and it only appeared—mainly in extremely fine particles—after pulverizing and washing. Magnetite was in every instance the most prominent mineral, its quantity varying between 43 and 67 per cent. Determinations of copper and sulphur showed that from 3.5 to 7 per cent. pyrites of copper, and from 3 to 22 per cent. pyrites of iron were present. The gold-value of the ore varied between 0.3 oz. and 0.8 oz. per ton. I do not speak of specimens, but of average samples of large quantities of ore put through the battery. In ore that had been crushed through a No. 40 screen, the gold appeared, in part, as free gold, the rest being thoroughly mixed with the magnetite and pyrites, both minerals containing about the same percentage of gold. If this free gold was brought in contact with pure quicksilver it (lid not amalgamate readily, even if the quicksilver was charged with sodium amalgam.

Jan 1, 1886

By F. C. Langenberg

DURING the course of some magnetic investigations which the authors have under way, six bars of 0.43-carbon steel were tested, a permeameter designed after the Hopkinson yoke type being used. The results obtained were of some interest and although far from complete serve at least to show the necessity for a careful investigation of the previous history of the samples under study as well as the chemical composition. A steel of given chemical composition may assume a great variety of structures, depending on its treatment. Professor Sauveur has devised a very clear and effective means of illustrating this point: The accompanying microphotographs show some of the possible structures assumed by a 0.30 carbon steel (Fig. 1). It is now a well-established fact that a structural change is accompanied by changes in the tensile strength, elastic limit, hardness, etc., and it seems reasonable to assume also, a change in the magnetic properties. Six bars of a 0.43-carbon steel were used, all the bars being taken from the same rod and treated as follows: Bar 1. Heated to 1,100° and cooled in the furnace. Bar 2. Heated to 1,000° and cooled in the furnace. Bar 3. Heated to 900° and cooled in the furnace. Bar 4. Heated to 1,000° and cooled in air. Bar 5. Heated to 900° and cooled in air. Bar 6. Untreated. The bars were then turned to 13 mm. diameter and tested by the Hopkinson yoke method. After testing, three specimens were taken from each bar, one from each end and one from the middle. The homogeneity of the. bars was tested in this manner and in no instance could any difference in structure be detected between the three specimens.1

Jan 2, 1915

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.' ' The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By J. Lohrenz, R. J. Francis, G. C. Clark

Compositional material balance methods have been extended to solution gas-gas cap-water drive reservoirs. Partial or complete pressure maintenance as well as reservoir repressuring by gas and/or water injection may be considered. Increrments of reservoir withdrawals and injections equivalent to a given time increment are used as the basic iterative step to allow the extension. An example field study shows how the reservoir volumes. extent of the water drive, and relative permeability ratio function may be estimated. Knowing these, the methods can be used to predict reservoir behavior. INTRODUCTION The compositional material balance is similar to conventional material balances in many aspects. The assumption of a pressure-homogenous reservoir with no transients is common to all conventional material balances1-1 although numerical methods are different. The compositional material balance also contains this assumption. Inclusion of phase equilibria directly in reservoir calculations is the key difference and improvement in the compositional material balance. A continuous account of the compositions of the reservoir fluids and effluents is determined. Calculations of fluid phases and properties can be based on these compositions. Excepting fluid phases and properties determined in this manner, the compositional material balance uses procedures exactly analogous to conventional methods. Brinkman and Weinaug5 and Jacoby and Berry6 have given compositional material balances for simple solution gas drive reservoirs; subsequently Jacoby and Berry' extended their procedure to include pressure maintenance by gas injection at constant reservoir pressure. This paper extends compositional material balance techniques to a more general combination drive reservoir with various types of pressure maintenance operations. The procedure for this extended compositional material balance and an example of its field application are presented. PROCEDURE The numerical calculations of this compositional mate- rial balance are performed on a high-speed digital computer. The most comprehensive case the present compositional material balance program can handle is a solution gas-gas cap-water drive reservoir with (1) water production, (2) water influx, (3) separate or commingled production from the oil and gas zones, (4) any surface processing arrangement including LPG and gasoline production, and (5) gas injection into the gas and/or oil zones." This description of the procedure applies to this most comprehensive case. Appropriate deletions in the procedure can be made for more simple mechanisms. ASSUMPTIONS In common with conventional material balances, the compositional material balance makes the following assumptions: (1) the total reservoir is at a uniform pressure at a given time; (2) the volumetric ratio of gas to liquid withdrawal at reservoir conditions is directly proportional to their mobilities; and (3) instead of assuming a pressure-dependent total gas-oil equilibrium, the cornpbsitional material balance makes a sianificantly different and more rigorous assumption as follows. Thermodynamic equilibrium exists for each component in the liquid-gas mixtures in the reservoir and in surface processing. These three assumptions are fundamental in the compositional material balance procedure. Other assumptions involve arbitrary simplifications of the reservoir mechanisms. This compositional material balance uses the following simplifying assumptions: (1) no bulk mixing occurs between the gas and oil zone; (2) total mixing occurs between any injected gas and the contents of the injection zone; (3) no in situ hydrocarbon liquid is produced from the gas zone; (4) no reservoir gas is retained behind any net bottom-water influx; (5) the residual saturation of hydrocarbon liquid at reservoir conditions behind any net bottom-water influx is constant; and (6) fluids retained behind any net bottom-water influx exert no further influence on the reservoir. These six assumptions are not fundamental. Modifications of the present procedure can be made for different assumptions of the reservoir mechanisms. THE TIME INCREMENT Previous compositional material balances have used a pressure increment for simple solution gas drive reservoirs"" and an increment of injected gas for pressure maintenance.' These increments are suitable for these simple cases. They are, however, inadequate for reservoirs with time dependent drive mechanisms including water drive. A time increment removes this inadequacy and is

US 4,141,854-Method of resolving water-in-oil emulsions from the organic solvent extraction of uranium from an aqueous ore leach solution The emulsion is treated at optimum temperature with a water-soluble acrylamide copolymer which contains 5-50% by weight of a lower alkyl substituted tertiary aminoethyl methacrylate or quaternary ammonium salts thereof The emulsion is broken, enabling recovery and reuse of the organic portion of the emulsion A M Pavilcius and M A Latko, assigned to Nalco Chemical Co Feb. 27, 1979 3 pp (252-301 1W) Filed: 12-14-77 (860,542). US 4,142,952-In the recovery of copper from an ore leach solution, the solution is contacted with a water-immiscible organic solvent containing 5 to 20 g/L of o-hydroxyaryloxime and 2 to 20 times the weight of the o-hydroxyaryloxime of nonylphenol The loaded solvent phase is separated from the aqueous phase and stripped with sulfuric acid Copper is recovered rapidly and in high yield from aqueous solutions containing high copper concentrations R F Dalton, as¬signed to Imperial Chemical Industries Ltd Mar 6, 1979 6 pp (204-106) Filed 1-3-77 (756,067). Priority: United King¬dom, 1-30-76 (3788/76), 6-15-76 (24722/76), and 10-21-76 (43711/76). Same- British 1,549,615, dated Aug. 1, 1979 US 4,148,631-In the recovery of nickel and cobalt from a mixed sulfate ore leach solution, both metals are extracted by means of a cationic extractant, the loaded extractant treated with an aqueous chloride or thiocyanate solution to back extract the cobalt, and the cobalt then recovered by solvent extraction or ion exchange with an anionic extractant Recovery is effected in a relatively few extraction steps. F Babjak, V A Ettel, and K. R Dymock, assigned to Interna¬tional Nickel Co , Inc, Apr. 10, 1979 6 pp (75-101 BE) Filed¬7-27-78 (928,401). Priority- Canada, 12-28-77 (293,967) US 4,148,813-An improved extractant for use in the recov¬ery of nickel and cobalt from an ore leach solution comprises a water immiscible organic solvent system containing solubilized mercaptide ions, e g , dodecanethiol. Cobalt and nickel mercaptides solvated in the organic phase are easily stripped in the presence of carbon monoxide and an aqueous alkaline solution A. S. Rappas and J. P. Pemsler, assigned to Ken¬necott Copp

Jan 1, 1980

By C. Bezemer, I. Havenaar

An investigation was carried out on the dynamic liltration behavior of drilling fluids. In a set-up consisting of a porous pipe through which the drilling mud was circulated, dynamic liltration rates and cake thicknesses were determined as a function of flow rate and filtration time. Eventually, a state of equilibrium was reached; i.e., both cake thickness and filtration rate attained constant values. Concurrently, dynamic filtration tests were carried out in a simple dynamic filter apparatus where mud flow was similar to that in a rotational vismmeter. In both arrangements the relation between equilibrium liltration data and rate of shear at the cake surlace was studied. Filter pipe and dynamic filter apparatus were lound to give identical relations. It was therelore concluded that the latter apparatus, which is suitable lor routine measurements on small amounts of mud, could be used to determine the dynamic liltration behavior of mud under borehole flow conditions. Some data are presented on the effect of filtration pressure and temperature on equilibrium filtration rate and cake thickness. INTRODUCTION In oil well drilling, the drilling fluid used generally forms a mud cake on the permeable sections of the borehole wall while filtrate is lost into the formation. As to the conditions under which this filtration process takes place, a distinction should be made between static mud filtration (mud is not circulating) and dynamic mud filtration (mud is circulating). In recent years several investigatorsl-5 have studied the process of dynamic mud filtration about which little had previously been known. This type of filtration is the subject of this paper which confirms several findings of previous investigators. It differs from already published works, however, in the following respects. 1. It contains a description of a simple laboratory apparatus developed for dynamic filtration measurements on small amounts of mud. 2. The effect of rate of shear at the cake surface on dynamic filtration has been studied. As a result of this study, dynamic filtration data pertaining to the borehole conditions of mud flow can be found from laboratory tests. 3. Some data are presented on the effect of filtration pressure and temperature on dynamic filtration. The work was limited to a small number of muds. No attempt was made to compare data on API filtrare loss with dynamic filtration rates. Previous workers have clearly shown that no correlation exists between static and dynamic filtration rates. EXPERIMENTAL ARRANGEMENT To establish whether the effect of mud flow conditions on dynamic filtrations is governed by the rate of shear at the cake surface, two different types of mud flow were used. In this connection the experiments were partially conducted by means of a porous pipe through which mud was circulated, partly in a dynamic filter apparatus which somewhat resembles a rotational viscometer. In both cases the flow conditions of the mud were well defined, thus making it possible to-calculate rates of shear at the cake surface. The filter pipe was 200 cm long with an internal diameter of 3 cm. Its perforated wall was covered on the inside with filter cloth on which the mud cake could form. Mud was pumped through the pipe at linear rates varying from 20 to 186 cm/sec. The required filtration pressure was obtained by means of a lack-pressure valve downstream of the filter pipe. In this arrangement the type of flow existing in the borehole is reasonably well simulated. The dynamic filter apparatus (Figs. I. and 2) consists mainly of two concentric cylinders with a clearance of about 0.5 cm. The outer cylinder (rotor) can be rotated at rates up to 1,000 rpm. The outer surface of the inner cylinder (radius about 2.5 cm) is covered with filter cloth or paper supported by copper gauze. The two cylinders are mounted inside a pressure

Jan 1, 1967

Jan 1, 1924

By J. L. Gillson

Historically, rock deposits and sand deposits of titanium minerals came into production about the same time, although there may be some argument as to what is meant by production. Beach de- posits of heavy minerals in India (Figs. 1-4) and Brazil (Figs. 5) were worked for monazite about the turn of century, but as there was then no market for titanium minerals, these were thrown away. The rock rutile deposits at Roseland, Va., Fig. 6, were worked to supply rutile for titanium chemicals and for coloring ceramics long before there was a titanium pigment business. The pigment industry started about the middle twenties, both in Europe and the U. S., and almost simultaneously the rock deposits at Ponte Vedra Beach near Jacksonville, Fla., were worked for titanium content. Since those days, production from both types of deposits has continued to grow at a rapid rate; many deposits of both types have been found, and reserves have grown to very large figures. In total tonnage of reserves, there is no doubt that the rock deposits are far ahead of the sand deposits; nevertheless there is a very large tonnage of commercial sands available. It is the quality of titanium mineral in the sand and the relatively lower costs of operating sand deposits that have kept them abreast, at least in annual tonnage produced, with the rock deposits.

Jan 4, 1959

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

Eighty-four quaternary titanium-base alloys from the following systems were investigated: 1. Titanium-chromium-carbon-nitrogen. 2. Titanium-chromium-carbon with copper, vanadium, molybdenum, manganese, iron, or nickel. 3. Titanium-chromium-nitrogen with vanadium, molybdenum, or nickel. The tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships of these alloys are reported. HIS paper is the third in a series describing J- titanium-base alloys. The first paper describingdescribed titanium binary alloys, and the second contained data on a large number of titanium ternary alloys. Eighty-four heats, comprising three groups of quaternary titanium-base alloys, are described in this paper as follows: 1. Titanium-chromium-carbon-nitrogen alloys. 2. Titanium-chromium-carbon alloys containing copper, vanadium, molybdenum, manganese, iron, or nickel. 3. Titanium-chromium-nitrogen alloys containing vanadium, molybdenum, or nickel. The methods of preparing, fabricating, and testing the alloys are described in the paper Binary Titanium Alloys. Quaternary Titanium - Chromiurn - Carbon -Nitrogen Alloys The properties of titanium-chromium-nitrogen and titanium-chromium-carbon ternary alloys have been described in the paper Ternary Alloys of Titanium. Because small amounts of nitrogen and carbon both appear to be somewhat beneficial, these additions have been investigated fairly completely in quaternary alloys containing chromium at the following levels of composition: 2.5, 3.5, and 5.0 pct chromium 0.25 and 0.5 pct carbon 0.1 and 0.2 pct nitrogen Mechanical Properties: The mechanical properties of these alloys are listed in table I. Fig. 1 and 2 show graphically a comparison of the tensile properties and hardnesses of quaternary alloys with those of the titanium-chromium binary alloys. Fig. 1 shows the comparison at 0.25 pct carbon, whereas fig. 2 shows the comparison at 0.5 pct carbon. It is concluded from these data that 0.25 pct carbon and 0.1 pct nitrogen are desirable additions to the 5 pct chromium-titanium base. It is further concluded that most of this improvement is produced by the nitrogen and that carbon is either harmless or mildly beneficial, at least up to 0.25 pct. Structure and Transformation Range: The effects of carbon and nitrogen on the transformation range of the titanium-chromium alloys were determined as part of the routine investigation. Additions of 0.25 pct carbon and 0.1 pct nitrogen had no appreciable effect upon the transformation range. However, the addition of 0.25 pct carbon and 0.2 pct nitrogen definitely raised the beta solvus temperature, as shown by fig. 3.

Jan 1, 1951

By B. M. Larsen, W. E. Shenk

This paper describes a method of reversal control of the open-hearth furnace that obtains in practice those effects considered below as essential to a completely automatic control, without appreciable interference with the natural rise and fall in temperature of the regenerative portions of the furnace system. Growing out of some studies of radiation pyrometry in open-hearth regenerators, it was developed during 1934-1938, and has been successfully applied to a number of commercial furnaces. The goal of open-hearth furnace operation is the highest rate of production of steel of proper quality consistent with good refractory life and fuel economy. This requires rapid heat transfer from furnace to charge, which in turn is dependent upon heating the furnace refractories to the highest safe operating temperature. The greater the heat input to the melting chamber, the sooner this limiting temperature will be reached, so that control methods in general that are designed to protect against overheating of refractories should help to maintain maximum fuel input and production rate. For the typical open-hearth system, with fixed regenerator capacity and with rate of fuel input usually restricted in its range of variation, our basic assumption is the idea that the only other important variable —that is, the time interval between successive reversals—should also be held constant or within a small range. The present reversal control was designed therefore so that, under normal operating conditions, no arbitrary limitation is imposed other than to keep the reversal interval within the optimum time range. However, since a near approach to completely automatic operation involves protection of refractories through the balancing of furnace end temperatures as well as emergency protection against temperature peaks above some upper limit, it was also felt essential to employ, as an integral part of the control unit, a temperature-measuring instrument to register the true temperature of the refractory surfaces at some critical region in the hot ends of the regenerative zones. As the basic elements of the control, we thus have one "maximum" and one lLminimum" time relay and a potentiometer recorder-controller, combined with switches and relays to operate as follows: I. Reversal normally occurs within an optimum range limited by the maximum and minimum settings to about 4 to 6 min. variation, but the actual interval usually is less variable and closer to the minimum setting. 2. The margin between minimum and maximum time is utilized, together with a "floating temperature limit" in the potenti-ometric control instrument, to correct any tendency toward temperature unbalance between ends of the furnace. 3. A second "maximum temperature

Jan 1, 1945

By Leendert de Witte, Fred J. Radd

In many areas caring failures can be directly related to electrical currents observed in the casings. It is the thesis of this paper that the observed casing currents are mainly due to electrochemical potentials of the type in evidence on spontaneous potential curves of electrical logs. The general nature of these potentials are discussed and an equivalent circuit is given for current and potential distributions around open holes. The casing forms a short circuit to these potentials and tends to average the effects of local cells. The case of casing corrosion opposite the Dakota water sands in the salt-mud area of Kansas is discussed anil used us a qualitative, illustration of the relation between SP's and casing currents. A method of quantitative derivation of casing current distribution frorn electric log SP curves, using linear transform theory, is described and results are compared with a measured current profile. The effects of hydrogen over-potentials at the cathodic portions of the pipe are considered and some laboratory data are given in support of conclusions regarding the over-1.01tuge.s. INTRODUCTION To date an appreciable amount of work has been done on the measurement of oil well casing currents and on the correlation of the anodic portions of the current profiles with corrosive casing failures. Speculations on the origin of the casing currents have, however, remained rather vague; and although almost every plausible cause has been mentioned, there is to the writers' knowledge no clear-cut expose' on the details of the causes of the corrosive currents in the literature. A study of current surveys and casing failures in the N.W. Burnett field, Ellis County. Kan.. indicated the probability that concentration cell emf's between the Wellington salt section and the relatively fresh waters in the Dakota sands were a major cause of the corrosion currents. A more general concept evolved upon analysis of the severe corrosive conditions in the Pleistocene sands in the Ventura Avenue and San Miguelito fields in California. In this area no major variations in the salt content of the formation waters occur and yet large casing currents are observed. An explanation is found in the fact that the local spontaneous potentials which are set up due to concentration contrast between the drilling fluid and the connate water are short circuited when casing is set. The very conductive path through the casing increases the magnitude of the currents and has the tendency to average local sources over fairly large intervals. Current will flow between the sections that are predominently shaly and the sections that are mostly sandy. At the places where the current leaves the pipe, corrosive attack will occur. This same phenomenon will be present wherever unprotected pipe is set through sections that show large SP kicks on the electric logs over reasonably thick interval~. GENERAL- NATURE OF THE SPONTANEOUS POTENTIALS When a sequence of sedimentary rocks is penetrated by a drill hole filled with a mud which has a different salt concentration from that in the formation waters, various types of electrochemical potentials are established between the formations and different parts of the mud column. Opposite clean sand sections. a simple liquid-liquid junction potential will be observed; while opposite argillaccous formations, a membrane potential, often referred to as shale potential, will be established. The first quantitative analysis of these emf's in terms of liquid junction and membrane potentials is due to Wyllie.1

Jan 1, 1956

By J. P. Pritchard, J. T. Pierce, O. G. Slay

This paper discusses the results of a technology-evaluation program to ascertain the feasibility of a piotornask-photoresist technology developed for fabrication of multiple-layer thin-film superconductive circuitry. The uehicle selected for this evaluation was a 120-bil associative data processor requiring a set of nine photomasks to define a similar number of patterned material layers of lead, tin, and polymer insulation. A total circuit area of 4 sq in. involved 2500 actitle and 12,000 passive crossings. Several short-free, electrically continuous specimens were satisfactorily completed under this program. Problems encountered in the preparation and use of the requi-ed set of Photomasks are discussed, as also are the problets of providing suitable external connections. A major retarding factor in the development of the superconducting thin-film cryotron technology for many years was the absence of batch fabrication means yielding necessary device density and count per substrate for practical applications. Early workers in the field desired only limited numbers of devices to permit careful study of discrete devices and representative circuitry integrating logic and memory capabilities. For these purposes mask stencils could be formed to selectively control the placement of materials, sequentially vapor-deposited in vacuum, to form the multilayer structure. In general a distinct pattern was required for each material layer; therefore, mechanical provisions were required to change not only the material source, but the patterning mask as well, before each deposition. All deposition steps were preferably performed in a single evacuation of the deposition chamber. Thus the means for storing, transporting, and registering masks and sources with respect to the substrate existed and were operated within the vacuum environment. In the authors' experience, the approach was and remains serviceable for preliminary device study, but was not extensible to an economical manufacturing method by virtue of the difficulties inherent in mask stencil preparation and use, and the capital investment implicit in the mechanization requirements. Since the commercial attraction of the cryotron technology stems principally from its potential for economical batch fabrication, the authors' program has placed major emphasis on fabrication methods. A highly useful method has evolved through adaptation

Jan 1, 1967

By Paul Billingsley

Introduction. THE Georgetown mining district is located in Deerlodge county, Mont., about 20 miles west of Anaconda. It lies along the divide between the headwaters of Warm Springs creek, draining eastward, and Flint creek, flowing west and north through the Philipsburg valley. The actual divide is formed by Cable mountain, a narrow ridge running north and south, terminating to the south in low hills overlooking Georgetown lake, and to the north in a high, rugged plateau that falls off to the west to the wide valley of Flint creek. Oil the eastern, or Warm Springs, slope of Cable mountain is the Cable mine, with the Hidden Lake mine a few miles north. On the western slope is the Southern Cross group, with smaller mines, the Twilight, Cincinnati, Red Lion, and Big Bill, at intervals to the northward. The Georgetown mines lie in the hills south of Cable mountain; the Philipsburg mines, of which the Granite Mountain, Bimetallic, Hope, and Trout are the chief, form a separate group to the north, overlooking Flint Creek valley and Philipsburg. (See Fig. 1.1) The region ranges in elevation from 5,000 to 9,000 ft. It is, with the exception of the lower valleys, well timbered with small fir and pine, although Cable mountain and the higher summits to the northward rise slightly above timber line. The main valleys have the smooth contours of glaciation, and their mouths are frequently choked with morainal deposits.

Jan 9, 1913

By Peter T. Luckie, Harold L. Lovell, E. R. Palowitch, A. W. Deurbrouck, James K. Kindig

PART 1: DENSE MEDIUM SEPARATION by E. R. PALOWITCH and A. W. DEURBROUK INTRODUCTION During 1965, 64.9 percent of the 512 million tons of bituminous coal and lignite produced was cleaned mechanically, of which 95 million tons was cleaned by dense medium processes.l The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes rose from 7.0 to 28.5 percent from 1938 to 1965. Dense medium separations include those coal preparation processes which clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes offer the following advantages over other coal cleaning processes : 1. Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of the feed in the range of e 0.1 specific gravity units. 2. Ability to maintain a separating gravity that can be controlled with ±0.005 specific gravity units. 3. Ability to handle a wide range of sizes (up to 14 inches). 4. Relatively low capital and operating costs when considered in terms of high capacity and small space requirements. 5. Ability to change specific gravity of separation to meet varying market requirements. 6. Ability to handle fluctuations in feed both in terms of quantity and quality. HISTORY Sir Henry Bessemer patented the first dense medium process in 1858. Solutions of the chlorides of iron, manganese, barium and calcium were proposed as separating liquids; the separation was made in a cone-shaped separator. One large-scale plant using calcium chloride was erected in Germany but soon was abandoned. The Chance process, using a mixture of sand and water, was first

Jan 1, 1968

By R. F. Mehl, J. K. Stanley

THE recrystallization of cold-worked metals is studied ordinarily by determining the temperatures required for complete recrystallization to occur within a given arbitrary time period, usually within 15 min. to 2 hr. The results obtained are conventionally assembled in a three-dimensional diagram relating this temperature to the amount of cold-work (percentage deformation) and the resultant grain size, though sometimes other modes of representation are employed.1 Such three-dimensional diagrams are not complete, for the number of variables exceeds the number represented. The process of recrystallization is characterized by a time-rate, a fact that is not portrayed upon ordinary recrystallization diagrams. It is known that recrystallization consists in the formation of new nuclei and the growth of these nuclei, a process that continues until the matrix is completely consumed and the original set of grains entirely replaced by the new. This knowledge is old.2 Truly heterogeneous reactions invariably proceed by nucleation and growth; the decomposition of eutectoid solid solutions provides an example about which much is known,3 and freezing, originally studied by Tammann, provides the classic example. Although recrystallization is not a heterogeneous reaction within the orthodox meaning of the term, the mechanism of the process is the same. As in eutectoid inversion and freezing, it should be possible to study the rate of isothermal recrystallization as a function of time, and it should also be possible to analyze the isothermal reaction curve into the component rates of nucleation and growth that determine them.* Other methods, not employing the rates of nucleation and growth, have been used to represent the rates of such reactions, but these in general have been artificial and have not led to progress .4,5† The theory of recrystallization is not in advanced state; if recrystallization data were obtained in terms of the rate of isothermal recrystallization, and in terms of the rate of nucleation and the rate of growth of recrystallized grains, and in particular if the temperature coefficients of these rates were measured accurately, an adequate theory should be more readily developed .27 Such an effort requires proper experimental technique, but especially requires suitable methods of mathematical analysis to convert measurements made upon a surface of polish into values for the rate of nucleation and the rate of growth and to combine these into a rate of isothermal recrystallization. These methods are now

Jan 1, 1942

By R. C. Wilcox, R. V. Lawrence, P. A. Calhoun

The V-Rh-Si, Nb-Rh-Si, and Cr-Rh-Si systems were investigated to evaluate the extent of solid solubility between binary Cr3O structures. All Cr3O components lie within the favorable atomic size range1 for the formation of the Cr3O structure. Previous studies indicated complete solid solubility between V3Si and V3Sn2 and no solubility between Sn and cr3si3 or Si and Nb3Rh.4 The Cr3O structure is not found in the Cr-Sn and Nb-Si binary systems. Powder compacts were are-melted under argon, homogenized in a vacuum at 1000°C, and water-quenched. Alloys containing greater than 15 at. pet Si were annealed 100 hr. X-ray diffractometer methods were used to study all systems utilizing copper radiation for the Cr-Rh-Si system and chromium radiation for the other two systems. V-Rh-Si System. The alloys prepared in the V-Rh-Si system and the measured lattice parameters for the Cr3O structure found in each alloy are listed in Table I. The characteristic Cr3O diffraction pattern was found in all binary alloys. The measured lattice parameter of V3Rh (VRS-1) is in agreement with the reported value5 while the value for V3Si (VRS-5) is only in fair agreement.' In

Jan 1, 1965

By C. H. Mathewson, P.W. Bakararian

The greatcr part of the literature on the plastic behavior of magnesium dates back to that active period of research in crystal mechanics immediately following the widespread preparation of isolated metallic crystals large enough for the application of conventional methods of mechanical testing. These investigations, performed on single crystals, revealed an analogy between zinc and magnesium with respect to their fundamental mode of deformation. in the operation of glide and twinning, respectively, on crystallographically similar planes. Mathewson and Phillips (1928)' by geometrical analysis identified the plane in magnesium as the twinning plane. Schiebold and Siebel (1931) confirmed this twinning planc, established the basal plane as the plane of slip, and a digonal axis I as the slip direction. They also rcported twin formation in a secondary role on the {IOI} plane. Schmid (1931)³ summarized and discussed the earlier evidence and presented the results of his own experiments on the effect of temperature and small amounts of soluble elements. From X-ray studies on extended wire single crystals, he concluded that slip along the basal plane in the direction of the digonal axis I closest to the stress direction was the sole slip system operating at atmospheric temperature. This conclusion was based on experiments with crystals of many different orientations relative to the stress axis. Special attention was directed to the basal plane and the digonal axis I, as the plane and direction of greatest atomic density. Determinations of resolved shear stress at the onset of plastic yielding-—i.e., the critical resolved shear stress—were also made; the average of these calculations showing 82.9 grams per sq. mm. This value varied only slightly up to 300°C. at which temperature it was found to decrease to 70.5 grams per sq. mm. The extension of his crystals at temperatures above 225°C. further disclosed the presence of new slip systems. After the origince specimens of circular section had been

Jan 1, 1943

By C. H. Mathewson, P. W. Bakararian

The greatcr part of the literature on the plastic behavior of magnesium dates back to that active period of research in crystal mechanics immediately following the widespread preparation of isolated metallic crystals large enough for the application of conventional methods of mechanical testing. These investigations, performed on single crystals, revealed an analogy between zinc and magnesium with respect to their fundamental mode of deformation. in the operation of glide and twinning, respectively, on crystallographically similar planes. Mathewson and Phillips (1928)' by geometrical analysis identified the plane in magnesium as the twinning plane. Schiebold and Siebel (1931) confirmed this twinning planc, established the basal plane as the plane of slip, and a digonal axis I as the slip direction. They also rcported twin formation in a secondary role on the {IOI} plane. Schmid (1931)³ summarized and discussed the earlier evidence and presented the results of his own experiments on the effect of temperature and small amounts of soluble elements. From X-ray studies on extended wire single crystals, he concluded that slip along the basal plane in the direction of the digonal axis I closest to the stress direction was the sole slip system operating at atmospheric temperature. This conclusion was based on experiments with crystals of many different orientations relative to the stress axis. Special attention was directed to the basal plane and the digonal axis I, as the plane and direction of greatest atomic density. Determinations of resolved shear stress at the onset of plastic yielding-—i.e., the critical resolved shear stress—were also made; the average of these calculations showing 82.9 grams per sq. mm. This value varied only slightly up to 300°C. at which temperature it was found to decrease to 70.5 grams per sq. mm. The extension of his crystals at temperatures above 225°C. further disclosed the presence of new slip systems. After the origince specimens of circular section had been

Jan 1, 1943

By W. B. Morrison

The principal factors influencing the total percent elongation of a lead-tin eutectic and several low-alloy steels which exhibit superplasticity were investigated. These factors are: a) Strain-rate sensitivity of the stress (m). b) Specimen geometry; in particular, diameter-to-length ratio (d0/l0), and surface irregularity (e.g. notches). A feature of the tensile deformation of a superplastic alloy is the early appearance of a neck which continues to extend throughout the test. As a result the total elongation is directly related to the diameter-to-gage-length ratio. The strain-rate sensitivity of the stress varies during extension, mainly because of microstruc-tural changes. A satisfactory correlation exists between the minimum strain-rate sensitivity and total elongation, as indicated in the equation shown below. Notches cause a considerable reduction in total elongation and their effect is greatest at high values of strain-rate sensitivity. An initial notch depth exists below which there is no appreciable effect on elongation. An equation relating elongation to strain-rate sensitivity and specimen geometry is proposed, THE total percent elongation of a tensile specimen is usually regarded as a measure of superplasticity. However, little attention has been given to the fact that total elongation is also a function of specimen diameter and gage length, even though the importance of geometry has long been recognized in the tensile testing of materials in which elongations are relatively small.* In the present study, the effect on superplas- tic extension of the ratio of specimen diameter to length was investigated and an analysis was made of strain distribution along the gage length. Superplastic alloys are characterized by having a flow stress sensitive to strain rate but relatively insensitive to strain.2"' In an earlier study,5 it was found that the strain-rate sensitivity of several low-alloy steels changed during the test and that the minimum value correlated best with total elongation. In the present study, the variation of strain-rate sensitivity during the straining of a lead-tin alloy was investigated. EXPERIMENTAL PROCEDURE Lead-tin eutectic alloy (32 pct Pb 68 pct Sn), made from high-purity lead and tin, was cast in the form of 1-in. diam rod. The rod was cold-rolled in stages to 0.25 in. diam and then swaged to 0.125 in. diam. Samples were cut from the rod at various stages of the mechanical working process. Tensile test specimens were then made by attaching threaded steel ends to the rods by an epoxy-base thermosetting adhesive which required a setting treatment of 2 days at room temperature. The rods were seated in the steel ends in holes approximately 0.01 in. oversize. The test pieces thus made were of various diameters and gage lengths. These were stored at a temperature of about -70°C (-94°F) until required for testing. The distribution of strain along the gage length of a specimen was determined at various stages of the tensile test. The lead-tin alloy was superplastic at room temperature and direct observations during testing were simple. The gage length was divided by reference marks into five initially equal units. These reference marks were made with ink and were reinforced during the test when the initial marks became faint. Photographs were taken, at intervals, of the deforming specimen and measurements of the elongation in each of the gage units were made on these photographs. Tests were also done on several superplastic low-alloy steels whose properties were described earlier.5 The chemical compositions of these steels are given in Table I. A diagram of the notched tensile specimen used in the steel tests is shown in Fig. 1. The specimens were tested at 900°C (1650°F) in a furnace through which a mixture of He + 2 pct H was continuously circulated.5 RESULTS Strain Distribution. Approximately 20 tests on lead-tin alloy specimens were conducted to determine the strain distribution during the test. An example is shown in Fig. 2 of the strain distribution in the gage

Jan 1, 1969

By Charles Becker

THE practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles. Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1936