Search Documents

By P. Breidt, E. S. Greiner

THIS note reports a determination of the melting point of germanium, and the liquidus of the Ge-Ga alloys; lattice constants of the a phase are given. The alloys were prepared by melting germanium (>20 ohm-cm resistivity) and gallium (99.6 pct) in evacuated silica tubes. The materials (50 to 70 g) were heated at 1000°C, held in the liquid state for about ¾ hr, and then cooled rapidly in the tubes. Points on the liquidus were obtained by thermal analysis which consisted of obtaining time-temperature data during heating and cooling the materials in high purity graphite crucibles and a helium at- mosphere. Temperatures were determined with a Pt—Pt-Rh thermocouple protected by a silica sheath. The couple was calibrated against a National Bureau of Standards calibrated couple and also against the freezing points of copper, silver, aluminum, and the 28.1 wt pct Cu, 71.9 wt pct Ag alloy eutectic. The samples for X-ray analysis were prepared by heating small pieces of the ingots in evacuated glass or quartz tubes at temperatures between 600" and 900°C for periods ranging from 2 hr to 22 days, periods deemed sufficient for equilibrium to be attained, followed by quenching in water. The heat-treated samples were ground to powder for X-ray analysis. The lattice constants of the germanium-rich phase (a) were determined with a baok-reflection focusing camera. The X-ray reflections (331 and 422 Cr Ka, 422 and 333 Cr KB) were corrected

Jan 1, 1956

By Lawrence P. Bonicatto

The steel industry's increased demand for higher grade pellets has caused the pellet producers to investigate methods of upgrading their product and the Hanna Mining Co.'s Groveland plant on the Upper Peninsula of Michigan is no exception. The low grade iron deposit is a complex mixture of magnetite and hematite with chert, quartz, jasper and various iron silicates.1 Beneficiation is by Humphrey spirals and anionic flotation of the iron minerals.2 Flotation of the spiral tailings makes up about 75% of the concentrate, while a minor amount of concentrate (less than 3%) is produced in magnetic circuits. The concentrate is pelletized at the rate of 1.6 million tpy. The initial concentrating facilities were constructed in 1958 and the concentrate was marketed as sinter feed until a pelletizing plant was added early in 1963. Grade improvement soon became a high priority research project, and several methods of concentration were investigated.

Jan 3, 1968

By E. W. Parker

THE anthracite region, from which there is produced annually about 80,000,000 tons, or approximately 15 per cent. of the total coal supply of the United States, has a combined area of a little less than 500 sq. mi. The total area occupied by the bituminous fields (including the sub-bituminous and lignite fields) is in the neighborhood of 400,000 sq. mi., so that 15 per cent. of the total output comes from this small area of only a little more than 0.1 per cent. of the coal-producing territory. of the United States. The productive anthracite area is divided into a series of basins or troughs, roughly parallel, extending. in a northeast-southwest direction through the. Counties

Jan 1, 1921

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members.) No. 544.-Mining engineer, 39 years of age, graduate E. M. with extensive experience in the United States, Canada and Spanish-speaking countries. Good organizer, energetic and resourceful. Experience covers mining and milling of gold, silver, lead, copper, zinc and tungsten. At present a Captain of Engineers, U. S. A., expecting to be released shortly. Open for engagement as manager, superintendent or examining engineer. Correspondence and personal interview solicited. No. 545.-Engineer and geologist, member, age 29 years, technical graduate and married. Six years' practical experience as surveyor, chief engineer and in exploration work in West, Southwest and Mexico. Speaks French and Spanish. Desires position with exploration company or as engineer and superintendent of small mine. Will be released from commission in United States Navy about February 1. No. 546.-For staff position-or manager. Member, married, graduate mining and metallurgical engineer, 18 years' experience in underground and metallurgical work on gold, silver, copper, lead and zinc ores. Details, references, and qualifications will be sent if requested, or may be seen at Institute office. Available immediately in United States or Canada. Would go reasonable distance for an interview if desired. No. 547.-Member, experienced in mine operating, engineering, general contracting and constructing. Technical graduate, mining engineer, married, age 38 years. Many years' practical experience while advancing through different positions to manager. Best of references and rating. Desires change. Position with future. Can obtain results. Salary commensurate with position. Available on short notice. No. 548.-Mining engineer, member, technical graduate, age 31, on military service since August, 1914, available after January 31. Best of references.

Jan 3, 1919

By H. M. Varner

Under sponsorship of the US Bureau of Mines and the Department of Energy, a new type of rotary rock drill was developed by The Bendix Corp. Originally developed for the production of holes for the installation of longer than seam height roof bolts, the flexible drill is a useful tool for many drilling applications. It allows hands-off or remote production of holes for increased drilling speed and greater operator safety in any strata suitable for rotary drilling. This paper discusses various applications and experience for the flexible drill system in coal, metal/nonmetal mining, and for civil engineering uses. Manual, remote control, and automatic roof bolter modules are also discussed.

Jan 1, 1984

By J. O. Glanville, L. H. Haley

Ice frozen from a dilute chemical solution is mechanically weaker than ice frozen from pure water. This phenomenon is the basis of a practical method for reducing the strength of a mass of frozen coal. If a chemical additive is applied to moist coal prior to its shipment during freezing weather, the resulting frozen coal can be more easily broken than in the absence of the chemical additive. This greatly expedites the unloading and handling of coal during winter. There has been considerable research into the nature and mechanical strength of ice frozen from various solutions. In this paper, literature relating to this process as well as literature relating to the chemical treatment of coal and mineral particulates is reviewed. Some important articles are discussed and speculations made about the nature of the ice-weakening process. A laboratory evaluation of the effects of chemical additives on the mechanical strength of ice and frozen coal has been made. An apparatus designed for this purpose is described, and some results obtained with it are discussed.

Jan 1, 1983

By Koert D. Burnham, John G. Broughton

WOLLASTONITE in Essex County, New York, occurs as a typical contact mineral in a series of rocks metamorphosed by anorthosite. Sole current use is in various types of electric welding fluxes. Its uniform lathlike shape suggests its use as a specialized filler.

Jan 1, 1944

By Robert B. Fulton

Staurolite, an iron aluminum silicate mineral, is used industrially as a high value-in-use sand-blasting agent, as a premium grade foundry sand, and as the source of aluminum in portland cement manufacture in areas where the aluminum constituent is not economically available from shale or argillaceous limestone. It is produced by E. I. du Pont de Nemours & Co. as a coproduct in titanium mineral production in Florida where it was first recovered on a commercial scale in June 1952 from the Pleistocene sand deposit known as Trail Ridge. In the Trail Ridge deposit it comprises about one-fifth of the heavy minerals, the principal other heavy mineral constituents being ilmenite, leucoxene, rutile, zircon, kyanite, sillimanite, and tourmaline. Staurolite and the other silicate nonconductive heavy minerals are separated from the conductive titanium minerals on high-tension separators. The silicates are then separated from one another magnetically, the staurolite being relatively magnetic. In the total processing, 200 tons of raw sand yield 7 tons of heavy mineral concentrate from which about one ton of staurolite is recovered. This process yields staurolite concentrates of the characteristics given in Table 1. These concentrates are sold as three products with the size distribution of subrounded particles shown in Table 2. All three grades are used in sand-blasting for cleaning metal, for paint removal, and for cleaning buildings. Staurolite compares favorably with lower unit cost abrasives, such as boiler slags and mineral aggregates, in applications where the abrasive is used only one time and is not recovered. Because it is hard, fine, clean, and dense it can reduce blasting time, with less material reportedly being required [ ]

Jan 1, 1983

By Raja V. Ramani, Ralph W. Barbaro

This paper presents an application of a Mixed Integer Programming (MIP) model to the problem of locating a centralized coal preparation plant and determining the production schedule for the mines. The system used for illustrating model application is hypothetical but realistic. It consists of three mines, two potential preparation plant sites, heavy media processing plant, and one market. The goal is to maximize the total profit of the system while satisfying the coal delivery schedule over a three year period meeting both quantity and quality requirements (ash, sulfur, and heat content). In addition to the base case, four different scenarios are analyzed. These four modifications are: (1) removing the flotation circuit from the preparation plant and sending all of the fines directly to the clean coal, (2) lowering the quality of coal from one of the mines, (3) applying discounts to the unselected site to improve its competitive position, and (4) adding a new mine. A detailed discussion of the base case and the effect of these four alternatives is presented.

Jan 1, 1983

By ir. H. Eraly

The allocation of miners to teams, and of teams to production faces, is complicated by the high degree of absenteism of miners in Belgium. Therefore, the exact knowledge of who is actually present at the beginning of a shift and of the exact skills of those present, enables the foremen and mine captains to constitute their teams before all men go down into the mine in the most effective way possible. This paper describes the system of attendance recording and of displays which the foremen use to constitute their teams and/or to interrogate the personnel data base in order to do so. It shows how the foremen dialogue with the computer, to change the function of a miner within a team, to another team, or the function of a team as a whole. The implementation of the system, data bases, and data communication equipment and procedures, is described. The benefits obtained are presented for each level of the company: foremen and team supervisors, engineers, mine management.

Jan 1, 1977

By Rodolfo V. de la Cruz

The in situ deformability of rock masses is determined by relating the applied load to the radial displacements of points on the borehole wall that are outside of the loaded surfaces. The external displacement method includes the steps in which: a) radial displacement sensors are installed to measure the change in length of a diameter of a borehole; b) unidirectional self- equilibrating pair of forces perpendicular to the direction of radial displacement measurements are applied on opposite sectors of the borehole wall, and; c) using elastic theory, the in-situ deformability of the rock mass can be related with the applied loads and measured radial displacements. The displacements outside the loaded surfaces are comparatively smaller in magnitude than displacements inside the loaded surfaces. These displacements, however, are sufficiently large and can be measured precisely by commercially available linear displacement sensors. Loads are applied by a conventional borehole jack. Existing methods for measuring the in situ deformability of rock masses yields unreliable results due to complex boundary stresses, small and varying contact areas, and the existence of fractures. It was shown that in the external displacement method, the effect of boundary pressure distribution and contact area are negligible. Also, since the displacements measured in the external displacement method were due to materials that are deeper inside the rock mass, borehole fractures have less influence on the calculated deformation modulus.

Jan 1, 1982

Discussion of the paper of COURTENAY DEKALB, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 331 to 337. HORACE V. WINCHELL, Minneapolis, Minn.-Mr. Dehalb summarizes the reasons which he believes are important for the revision of the mining laws, as follows: "1. The conceptions as to the characteristics of orebodies that were held at the time the statute of 1872 was enacted have since proved to be in many respects erroneous." We all appreciate the force of that suggestion. The idea of the old prospector who made rules and regulations in the early days, which were attempted to he incorporated, so far as possible, in the Mining Act of 1872, was that all of the veins in a certain district outcropped upon the surface, or approximately parallel to each other upon the surface, and maintained that parallelism beneath the surface. Therefore, it seemed perfectly proper and natural for each man to stake his claim upon an outcropping, and have the right to follow that vein in working downward, with the general expectation that his workings would always remain just as far away from those of his neighbor as the outcroppings upon the surface. This does not happen to be the case. Dr. Raymond has very ingeniously referred to the subject in one case, in words which read as follows: "If all mining properties presented this beautiful simplicity of structure (ideal location of ideal vein), and all mining locators exhibited a corresponding simplicity of purpose, the application of the law would be easy, but the naiveté of the statute fares badly between the freaks of nature and the tricks of man."

Jan 5, 1915

By J. L. Lamon, W. Crafts

P. Coheur and L. Habraken—We read this paper with great interest and are glad to congratulate the authors for their valuable work, supplying an important contribution to the mechanism of tempering on the carbides in vanadium steels. We are in a good position to appreciate this work since we have been studying, for more than a year, Cr-Mo steels of a composition similar, but less highly alloyed (namely 0.1 pct C, 3 pct Cr, 1 pct Mo). Our results are quite in concordance with the authors', however, we wish to point out that it is very interesting to use equally the electron microscope in order to observe the variations of microstructure in steels. We have studied simultaneouslv the evolution of the carbides in situ with the electron microscope, and, after extraction, again with the electron microscope, and then with X-rays. The first results which we have obtained have been communicated at the Congress of Delft (July 1949) and at the "Journbes de la Metallurgie" in Paris (October 1949). These may be summarized as follows: After tempering with varying either the tempering temperatures or the tempering times, the carbides show two evolutions. The first one is connected to the carbides existing in the steels, principally in the boundaries of the grains. For some groups of steels these carbides may coalesce and for other groups they may

Jan 1, 1951

CHICAGO SECTION CHAS. H. MACDOWELL, Chairman, LUTHER V. RICE, Vice-Chairman, HENRY W. NICHOLS, Secretary-Treasurer, GEO. P. HULST, ALEX. K. HAMILTON, FREDERICK T. SNYDER, HENRY P. HOWLAND. The Field Meeting of the Chicago Section proved to be the most enjoyable meeting ever held by the Section. It took the form of a visit to the Northern Indiana Industrial District where the day was spent inspecting metallurgical plants in Indiana Harbor and East Chicago and in amusement at the Hammond Country Club. The weather was perfect and about 50 members and ladies attended the meeting. An inspection of the plant of the Inland Steel Co. occupied the morning. The plant was decorated in honor of the occasion and the company provided attractive souvenirs. It was noticed here that many of the ladies displayed an interest in the inspection and an understanding of the processes that would not have shamed professional metallurgists. While the members of the Section seemed to be most interested in the by-product coke ovens and the by-product recovery plant, the ladies enjoyed especially watching the snake-like antics of the red-hot rods in the wire mill. Leaving the steel plant, the Section enjoyed a ride through the district by automobile and arrived at the Hammond Country Club in time for lunch. In the afternoon some of the members inspected the plant of the International Lead Refining Co., at East Chicago, while the rest spent the time at the Country Club in golf, tennis, trap shooting, bridge and other amusements. During the dinner at the Hammond Country Club an informally organized male quartette led the singing in real college boy style. In the evening, E. E. Billow talked on the use of oil burners in metallurgical furnaces, Mr. MacDowell told of the present status of the Potash Industry and the Secretary told of some of the happenings at the Arizona Meeting. HENRY W. NICHOLS, Secretary.

Jan 12, 1916

By C. D. Hall

This paper may be divided into two main parts: (1) analysis and data to show that Eq. 6 adequately correlates the authors' experimental data, and (2) the assertion that Eq. 20 "should permit scale-up with data taken from one pipe diameter for Newtonian, inelastic non-Newtonian, and viscoelastic fluids, such as dilute polymer fracturing fluids, which produce considerable pressure reductions." The authors might well recommend that this broad grouping of fluid types could be correlated by using Eq. 6 (requiring data from at least two pipe diameters). On the other hand, Eq. 20 is only shown to be adequate for conditions within the range of the present data set. Specifically, predictions by Eq. 20 for diameter scale-up to casing sizes would give larger deviations than implied in Table 2, and scale-up for some other fluids that give large drag reduction could be grossly in error. The description of a class of fluids "which produce a diameter family of straight parallel lines on a log (d?p/4L) vs log (8 v/d) plot. . ." defines a necessary condition for using Eq. 6; i.e., that s shall be constant for each fluid. The proposal that Eq. 20 is applicable to turbulent flow of such fluids is equivalent to saying that the spacing of these parallel lines, with A being constant, will be found to correspond to m = -1.20 for all such fluids. Table 1 shows the values of m derived from data on 16 non-Newtonian fluids. The key statement of this paper is that the diameter exponents "do not vary significantly from . . . -1.20." In statistical terms, this says that the m value for each fluid, which was obtained from all the measurements made on that fluid. has not been shown to be different from the arithmetic mean of the m values for the 16 fluids tested. This implies that the group mean, -1.20, is a more reliable value to use for an individual fluid than is the m value derived from the data on that fluid alone. No statistical test is described to support the key statement that the diameter exponents do not vary significantly from -1.20. Such a test would have to take into account that each individual m value is shown to correlate the pressure gradients for its fluid, with only about 3 percent standard deviation over the diameter range covered. That is, the m value is not the result of a single independent measurement. Thus, it would not be sufficient, or valid, to compare the deviation of one of the m values with the variance of the 16 values of m about their mean. An alternative interpretation of the key statement is that the diameter exponents do not vary appreciably from -1.20; i.e., that using -1.20 does not cause serious inaccuracy. Table 2 seems to be offered in support of such an assertion. However, such a statistical treatment (1) is unnecessary and (2) cannot lead to any valid scale-up generalization. The amount of error introduced by using a 1"wrong" value of diameter exponent — i.e., -1.20 instead of m — is determined by Eq. 6. The ratio of the pressures predicted by Eqs. 6 and 20 for scale-up from ds in small pipe to d, in casing is The pressure for 30-percent calcium carbonate slurry (m = -1.112) in 10-in. ID pipe would be predicted 30 percent higher by Eq. 6 than by Eq. 20, if based on tests in 0.5-in. ID pipe. The data set tested in Table 2 represents only a limited sample of pipe diameters (ratio of about 4:l) out of the population of diameters that would

Jan 1, 1970

By Effingham Humphrey

THE Lehigh Valley. Coal Co. finished the rebuilding of its Drifton No. 2 breaker at Drifton, Pa., in the summer of 1917. The new construction comprises an addition and the complete remodeling of the old breaker. It is of interest to note that the old structure was the first iron breaker erected in the anthracite region. THE OLD BREAKER This old breaker was built by the Cross Creek Coal Co., under the direction of the late Eckley B. Cole, in 1888-89, and was fully described by him in the Transactions.1 The columns were cast iron, 8,'10 and 12 in. square. The floors and partitions in pockets were cast-iron ribbed plates. The struts were cast iron of "H" section; the other members were of structural iron either rolled I-beams or built-up sections. The sizes of the rolled beams varied from 6 to 20 in. deep, while the built-up sections, made of plates and angles, varied from 6 to 63 in. in depth, so that there apparently was no rule to determine the type of section used. In the remodeling of the old structure, practically everything was taken clown excepting the columns and roof, and such beams as were necessary for temporary construction purposes, and, therefore, a close inspection of the old structural members could be made and the effect of the acid water oil them could be noted. The cast-iron members were but slightly attacked by the water, while the wrought-iron beams, in the wet places, were corroded almost to failure.

Jan 2, 1918

By F. P. Dewey

The subject of this paper does not embrace the consideration of ways and means for the increase of analytical accuracy, or the question what could or should be attained in that direction. I desire simply to call attention to the degree of accuracy exhibited in actual every-day practice. In estimating this, little weight will be given to the evidence afforded by the agreement of duplicate or multiple determinations by the same chemist; for I am convinced that such agreement is a delusion and a snare. Nor will special importance be attached to the agreement of two or even three analyses in special cases, or to the agreement between two methods practiced by the same analyst. I propose to compare the results obtained by several chemists, working upon the same sample and by various methods, in order to exhibit, as I have said, the actual condition of practice. The available material for illustrating this phase of the question is unfortunately scanty; but something has been done; and I hope, by calling attention to some of the work in this line, to stimulate further work in the same direction by inducing others to prepare suitable samples and submit them to various chemists who are competent and willing to make the necessary determinations, and fully describe the methods they employ. I draw most of my illustrations from the Transactions of the Institute, the Proceedings of the Association of Official Agricultural Chemists, and from personal experience. Manganese in Steel.—In May, 1881, Mr. William Kent presented a paper to the Institute entitled " Manganese Deter-

Jan 1, 1897

SHELBY M. HARRISON,* New York, N. Y. (written discussion ?).¬Your secretary requested a brief description of the Russell Sage Foundation, in order that members of the Institute, if they should desire to avail themselves of it, would know what type of service is offered to them through our institution. The foundation was established in 1907 by the gift of Mrs. Russell Sage of $10,000,000 as a capital fund, the income of which is to be spent for the improvement of social and living conditions in the United States. One of the lines of activity which the foundation has felt would lead toward this end is the development and promotion of community surveys; and because the scope and methods followed in these surveys are very similar to the scope and method of much of the institution's work in general, an idea of its main activities can perhaps be given best by describing one of our surveys. Incidentally, it may be pointed out that antecedent to the survey stand at least two important facts: first, the recognition. that communities are active, not static forces, that they develop, that changes in. material and human relationships occur continuously, and that with them come new social and civic problems which must, in many cases, be diagnosed and prescribed for anew; and second, the reality of scientific advances along lines which make possible at least some measure of solution of the problems. Evidences of these changes are abundant; many of them are found in the rapid growth of cities in the last few decades. Villages in agricultural districts, places where everybody knew everybody else, where the pulpit had been long the chief or only influence molding public opinion, where the air was unclouded by the smoke from factory stacks, where the water supply was not affected by pollution, where sunlight and building

Jan 5, 1918

By D. C. McLean

This report summarizes the work that has been done during the past several years in adapting resins for use as auxiliaries in mine roof support. The resins were applied in two ways: 1) by injection into the strata, and 2) as a bonding agent for roof bolts and reinforcing bar. The Explosives and Mining Chemicals Department of the American Cyanamid Co. has worked during this period in cooperation with the Roof Control Research Group of the U.S. Bureau of Mines, the Pattin Manufacturing Co., the J. H. Fletcher Co., the Homestake Mining Co., the U.S. Steel Corp., the National Mines Corp. and the Pocahontas Land Corp. in an effort to create resin formulations and methods for applying them as a practical and sate type of roof support for mining areas particularly where conventional support is inadequate, yet expensive. This, work has involved much pioneering in a field where theory, speculation, and pure mythology predominates, and little basic engineering data is available. It is strange butt true that, despite the importance of roof control both from an operational and safely standpoint, there is scarcely a mining' company in this country that has an engineer, or anyone, assigned to the study of roof support problem, except temporarily--after a bad roof fall. The responsibility for improving roof control methods seems to have been placed entirely upon the shoulder, of the USBM, various State departments of mines, and individual roof bolt manufacturing; companies. It was in cooperation with the USBM that Cyanamid first developed resins for mining use.

Jan 1, 1964

By H. F. Yancey, O. L. Furse

Although usually coal is screened with punched plate screens having round-hole perforations, there has been an increasing use of wire-cloth screens with square apertures, especially at pneumatic coal-cleaning plants and at other plants that use vibrating screens. It is therefore desirable to establish a relationship between round-hole and square-hole screens for use not only in experimental investigations of coal-preparation problems, but also for use in commercial operations. This need is apparent whenever it is necessary to substitute wire cloth for punched plate and still retain the familiar trade-size product. Although similar work probably has been done by industrial organizations concerned with the screen sizing of coal, the only recorded study of the subject other than the one described herein of which the authors are aware is that of Roesler,1 who screen-sized two samples of limestone and two of zinc concentrates crushed to pass 1/2 in. with a set of square and round-hole screens and found the ratio to be 1:1.23. Procedure In the course of a study of various methods for determining the friability of coal,2 it was necessary to screen-size the products of a series of friability tests of three different coals with both round-hole and square-hole screens. The coals used were from the Roslyn No. 3 and the Bayne mines in Washington and the Rolapp mine in Utah. Twenty 25-lb. samples of each of these three coals at 3 to 2 1/2 in. round-hole size were dropped from a height of 10 ft. to a concrete floor, and then screened with

Jan 1, 1934