Search Documents

By William F. List, Marvin A. Schuster

Monolithic electrooptical mosaics of 2500 photo-transistor elements with internal row and surface column interconnections have been fabricated by epitaxial-planar diffsion techniques. Unique access to any elemed of the mosaic is provided through one of the fifty X and one of the fifty Y external leads. The sensor mosaic can be used for imaging applications and has a 1:1 aspect ratio, a resolution of 100 lines per in., a dynamic range in excess of lo3, a sensitivity of 0.5 per pw, element response within a 2:l range over 75 pct of the mosaic, and a minimum detectable signal of the order of 10-' w. Design considerations which ilnpose particclar fabrication yequirements are disctussed along with some of the problems peculiar to the epitaxial and planar-dijfision techniqes by which this device is fabricated. The solid-state silicon monolith has an imaging area of 0.5 by 0.5 in. and an element center -to- center spacing of 0.010 in. J monolithic solid-state electrooptical device has been developed as the photon-sensing mosaic for use in an image-converter system.' This system is the solid-state equivalent of the vidicon and can image radiation in the visible and near-infrared regions of the spectrum. The electrooptical image converter has the desirable size, weight, reliability, and low-power characteristics inherent in solid-state devices. It is read out by direct-wire means rather than by beam-scan techniques. The packaged unit is shown in Fig. 1. A selection of material for the sensor was based on considerations of both reliable fabrication techniques and material spectral response. Silicon was selected both for its response from the lower end of :he visible to the long-wavelength cut-off above 11,000A and for its well-developed epitaxial planar-diffused technology. The electrical image is composed of M x N discrete information bits with each bit emanating from one of the individual phototransistor sensors. The interconnected mosaic concept was introduced to provide a structure which is both manageable in its number of leads and compatible with conventional viewing systems which accept XY data. Interconnections along the Y direction are provided by internally diffused strips, while interconnections along the X direction are formed by vacuum-deposited metal surface bars. Unique access to any individual element of the M x N mosaic is available through one of the M and one of the N external leads. PHOTOTRANSISTOR DESIGN A phototransistor structure2 was selected for the discrete photon detectors of which the mosaic is com- posed. Basically, the mode of phototransistor operation is such that incident quanta are absorbed in the base area of the element where they generate electron-hole pairs. If the electrons are liberated within a diffusion length of the depletion region around the collector junction, they will diffuse to this depletion region and be swept across the junction where they account for a small component of the photocurrent. Similarly, the holes which are created within a diffusion length of the emitter junction will diffuse to this region where they forward bias the emitter and so induce injection of minority carriers into the base. This accounts for the substantial transistor photocurrent. This mechanism of operation implies several design and fabrication goals for the individual sensor elements: high electrooptical conversion efficiency, sufficient carrier lifetime in the base regions, and a maximum volume in which photons can be absorbed within a diffusion length from the depletion layer about the junction. Moderately high transistor gain is desirable to permit readout at low light levels; however, very high gain has a deleterious effect on mosaic dynamic range. The mosaic must also be characterized by good uniformity of element response as well as by good isolation between elements. The above set of conditions imply that junction depths must be optimized with respect to photon ab-

Jan 1, 1967

By G. D. Cremer, J. J. Cordiano

Aluminum powder is a well-known article of commerce and in various forms has been marketed widely for use in paint, for pyrotechnic purposes and for exothermic mixtures. For a number of reasons, however, aluminum powder has not been employed extensively in powder metallurgy, although a great many proposals along this line have been offered. Aluminum and alumiuum-alloy powders oxidize readily upon exposure to air and the thin film of oxide (or hydroxide) thus formed is highly refractory, in that ordinary gaseous reducing agents such as hydrogen or carbon monoxide do not reduce the oxide to metal at temperatures below the melting point of aluminum. It has been thought that the presence of these films of oxide on aluminum particles would interfere markedly in powder metallurgical work and a number of suggestions have been made, either for preventing the formation of the film through the production of the powders in inert or reducing atmospheres, or for the removal of the oxide by means of powerful reducing agents, including "nascent" or atomic hydrogen released from metal hydrides. A second and more serious difficulty in the use of aluminum and aluminum-alloy powders in powder metallurgy resides in the fact that during compression such powders tend to adhere or cold-weld to the die walls, thus interfering with the formation and ejection of a compact. A third difficulty, which has been encountered only with aluminum-alloy powders, is their hardness when compared with elemental aluminum. Certain of these powders are susceptible to age-hardening, which further hinders the formation of strong green compacts. These conditions are particularly true of atomized aluminum-alloy powders. Even in the annealed condition, plastic deformation of alloy powders under pressure is low when compared with unalloyed powders. This fact, coupled with the lower corrosion resistance of the alloy powders. is probably the significant factor in our failure to obtain strong sintered pieces. Methods of Puoducing the Powder Many methods have been proposed for manufacture of aluminum powder, only a few of which are used commercially. Several of the more important processes include: (I) atomization of the molten metal; (2) mechanical pulverization and other types of comminution; and (3) graining, in which molten aluminum is stirred during freezing. For pigment and certain pyrotechnic uses aluminum flake powder is desirable, because of its greater proportion of surface to volume; and large quantities of such material are made by a procedure that involves stamping or ball milling. In making flake intended for use as pigment,

Jan 1, 1943

By G. D. Cremer, J. J. Cordiano

Aluminum powder is a well-known article of commerce and in various forms has been marketed widely for use in paint, for pyrotechnic purposes and for exothermic mixtures. For a number of reasons, however, aluminum powder has not been employed extensively in powder metallurgy, although a great many proposals along this line have been offered. Aluminum and alumiuum-alloy powders oxidize readily upon exposure to air and the thin film of oxide (or hydroxide) thus formed is highly refractory, in that ordinary gaseous reducing agents such as hydrogen or carbon monoxide do not reduce the oxide to metal at temperatures below the melting point of aluminum. It has been thought that the presence of these films of oxide on aluminum particles would interfere markedly in powder metallurgical work and a number of suggestions have been made, either for preventing the formation of the film through the production of the powders in inert or reducing atmospheres, or for the removal of the oxide by means of powerful reducing agents, including "nascent" or atomic hydrogen released from metal hydrides. A second and more serious difficulty in the use of aluminum and aluminum-alloy powders in powder metallurgy resides in the fact that during compression such powders tend to adhere or cold-weld to the die walls, thus interfering with the formation and ejection of a compact. A third difficulty, which has been encountered only with aluminum-alloy powders, is their hardness when compared with elemental aluminum. Certain of these powders are susceptible to age-hardening, which further hinders the formation of strong green compacts. These conditions are particularly true of atomized aluminum-alloy powders. Even in the annealed condition, plastic deformation of alloy powders under pressure is low when compared with unalloyed powders. This fact, coupled with the lower corrosion resistance of the alloy powders. is probably the significant factor in our failure to obtain strong sintered pieces. Methods of Puoducing the Powder Many methods have been proposed for manufacture of aluminum powder, only a few of which are used commercially. Several of the more important processes include: (I) atomization of the molten metal; (2) mechanical pulverization and other types of comminution; and (3) graining, in which molten aluminum is stirred during freezing. For pigment and certain pyrotechnic uses aluminum flake powder is desirable, because of its greater proportion of surface to volume; and large quantities of such material are made by a procedure that involves stamping or ball milling. In making flake intended for use as pigment,

Jan 1, 1943

By J. J. Kanter

The choice of a nonferrous metal or alloy for a given Application is frequently predicated upon a consideration of properties other than merely the capacity to withstand stress. When ability to withstand stress is the dominant engineering requisite of the material to be used, economic considerations seldom lead to the choice of nonferrous metals and alloys. In most instances where a nonferrous metal is used it is because of some special quality of either corrosion resistance, electrical properties, thermal properties, antifriction, or fabrication advantage that commends its application. The mechanical properties, as a rule, present an incidental engineering consideration entirely secondary to the special quality deciding its use. Indeed, great ingenuity has often been exhibited by engineers and metallurgists in overcoming the mechanical shortcomings of a nonferrous base material. in order to take advantage of some outstanding property. . With this thought in mind, we might better appreciate some of the problems in stress design. encountered with nonferrous metals and alloys pertinent to a symposium on their creep characteristics. Our considerations must necessarily be far from complete because of the broad range of materials in the nonferrous category for which creep properties assume a technical interest. Creep deformation of these metals can be subject for study at temperatures ranging from ambient to incandescent, depending upon which one is under consideration. Whereas the steel metallurgist thinks of creep as an essentially high-temperature engineering consideration, the same is not necessarily true in the field at hand. The diversity of the creep problems in the nonferrous field is perhaps accountable to some extent for its virginity as a symposium subject. Each research has necessarily been sponsored by some organization or group interested either in promoting the use of a certain nonferrous base or in obtaining data toward the solution of a mechanical difficulty encountered in applying a material indispensable for its special attributes. Perhaps as many techniques of creep testing have been used as there are base metals implied under "nonferrous." Some of the creep problems that have occasioned researches are associated with steam-pressure vessels such as tubes, drums, castings, and forgings of copper-base and nickel-base alloys, cable sheathings of lead and lead-base alloys, electrical transmission lines of copper and aluminum, engine parts die-cast from alloys based on zinc, aluminum, copper— soldered and brazed joints-—as well as numerous duties at extremely high temperatures met with alloys based on cobalt, nickel, tungsten, molybdenum, platinum, and other precious or semiprecious metals. Postwar technology will have the benefit of much creep research on nonferrous metals, which for reasons of security cannot be discussed on this occasion. Suitability OF Metals As already intimated, the bulk of the constructional metal that ordinarily is

Jan 1, 1945

By Milton E. Wadsworth, Edward M. Eyring

BETTER understanding of solid surfaces and their associated adsorption products is of both academic and practical value. The study of detergents and their behavior in cleaning surfaces is fundamentally related to the nature of the products adsorbed and their ability to compete for certain surfaces. Similarly in flotation, the nature of the adsorbate before and after adsorption is basic to clear understanding of the process. The recently developed pellet technique1,2 employing infrared spectroscopy provides a powerful tool for the study of solid surfaces. Absorption bands, which are infrared-active, may be observed for adsorbed products. Also any changes in the surface substrate that occur as a result of adsorption may be detected by means of differential spectra. In applying the pellet technique to solids of large surface area, French and his coworkers3 have surveyed the adsorption of organic flocculants on clay minerals, oleic acid on fluorite, and ammonia on cracking catalysts. Recent work on application of differential infrared spectroscopy to the study of solid surfaces' has demonstrated that the difference between a sample and a reference can be obtained with double-beam instrumentation. In this way displacement of surface products, adsorption of new products, and differences in the substrate, if any, may be detected. Experimental Procedure: Potassium iodide pellets were used in this study, prepared from recrystallized analytical reagent grade KI. Grinding was carried out in a Fisher mechanical agate mortar. Two-gram plates containing the solid under study were pressed in a special evacuated die constructed in the laboratory at the University of Utah." Concentration depended on the solid in question. Zinc sulfide and willemite are sufficiently transpar- ent in the infrared region for concentrations as high as 20 mg of mineral in 2g of KI to be used. Zinc oxide is even more transparent, permitting concentrations as high as 60 mg in a 2-g plate. For non-differential operation, however, much lower concentrations (2 to 10mg/2g KI) had to be used. Spectra were obtained on a Per kin-Elmer 21 double-beam recording infrared spectrophotometer. A sodium chloride prism was used giving a spectral range of approximately 2 to 15 v wave length. For differential runs a resolution of 1000 was used and the scanning speed was controlled commensurate with instrument response. The response was checked continuously and each spectrum was repeated several times. For nondifferential runs a resolution of 927 was used. Zinc oxide used was analytical grade oxide fume. The zinc sulfide was precipitated from solution with analytical grade zinc sulfate and sodium sulfide. The precipitate was washed and centrifuged several times and dried. Before use the precipitate was washed in dilute HCl and then treated with saturated NH4Cl to remove any bulk oxides and sulfates. X-ray patterns of the precipitate were comparable to that of the natural mineral sphalerite. The precipitate was much more satisfactory than finely ground natural ZnS because of its very large surface

Jan 1, 1957

By John W. Vanderwilt

The unpredictable behavior of ground movement and subsidence has complicated the problems that attend the extraction of large quantities of ore. Special studies, particularly relating to coal mining, have yielded such a voluminous literature and so many involved controversial theories that a partial review would be difficult. Limited space makes any kind of a review impractical. The features to be considered cover only a relatively small part of the broad problems of ground movement and subsidence, but it is believed that this small part is critical. The practical aspects are important, since they bear directly on safety of mine workings, on recovery of ore and on dilution of ore in block caving and related systems for extracting large quantities of rock. The ground movement to be described occurs outside the vertical boundaries of a caved block in the area that is commonly referred to as being in the "zone of draw." "Draw" is a term that originated in the subsidence problems related to coal mining, and it is defined by a line drawn from the margin of the area caved underground to the most distant fracture at surface on the same side of the caved area as shown in Fig. I.' A line thus drawn is called the cave line, and its angle with respect to the horizontal is the cave angle or angle of draw. It is understood that the line is taken normal to the limit of mining, and in a vertical plane. The prevailing theories as to draw and angle of draw assume that appreciable movement occurred along the cave line, which has been described as a fracture resulting from the shearing action brought about by the weight of the overlying load. Fig. 3 shows diagrammatically the mechanics of ground movement adjacent to an area of subsidence according to the prevailing theory of draw (A, from Royce2) and, for comparison, ground movement observed in the Climax mine (B). The text in Peele's Handbook2 referring to Fig. 2 does not state the meaning of the "original position of top of workable ore" in the rectangular space above "ore in place," and the arrows are not explained. However, this presentation is most concerned with the zones outside the rectangle. According to the prevailing theory, as shown at the extreme left under A, Fig. 2, the vertical tension cracks at surface change at a shallow depth to shear fractures forming the cave line, and it is assumed that appreciable movement takes place along the cave line toward and into the subsiding caved block. The mechanics of ground movement observed in the Climax mine, as shown under B, Fig. 2, does not accord with the prevailing theory, particularly as regards the cave angle and draw. The vertical tension cracks seen at surface die out at depths of 150 to 225 ft. and shear fractures do not develop. Movement is confined at surface to a mantle of rock 50 to roo ft.

Jan 1, 1949

By J. T. Norton, Joseph Gurland

IN spite of the extended use and high state of practical development of the cemented tungsten carbides, the structure of these alloys is still a matter of considerable controversy. The characteristic high rigidity and rupture strength of sintered compacts have been attributed to a continuous skeleton of tungsten carbide grains, formed during the sintering process. This view is based mainly on the work of Dawihl and Hinnuber,1 who reported that a sintered compact of 6 pct Co maintained its shape and some of its strength after the binder was leached out with boiling hydrochloric acid. After leaching, only 0.04 pct Co was reported to remain in the compact. They also showed that the assumed increasing discontinuity of such a skeleton, as the cobalt content is increased, could be made to account for the observed discontinuous increase of the coefficients of thermal expansion, the loss of rigidity, and the impaired cutting performance of alloys of more than 10 pct Co. Contradictory evidence was cited by Sanford and Trent,' who mentioned that a sintered compact was destroyed by reacting the binder with zinc and leaching out the resulting Zn-Co alloy. The skeleton theory also does not account for the observed change of strength of sintered compacts as a function of cobalt content. If the skeleton is responsible for the strength, the latter would be expected to decrease with increasing binder content. Actually, the strength increases and reaches a maximum around 20 pct Co. In addition, tungsten carbide is brittle and undoubtedly very notch sensitive. The highest value found in the literature for the transverse rupture strength of pure tungsten carbide prepared by sintering is 80,000 psi.3 herefore, such a skeleton does not easily account for a rupture-strength value of 300,000 psi and higher, commonly found in sint.ered tungsten carbide-cobalt compacts. In view of the conflicting data present in the literature, experiments were undertaken to determine whether the sintering of tungsten carbide-cobalt alloys leads to the formation of a carbide skeleton or whether the densification behavior and the properties of cemented compacts are consistent with a structure of isolated carbide grains in a matrix of binder metal. The specimens were prepared from powders of commercial grade. Tungsten carbide powder ranged in particle size from 0 to 5x10-4 cm. Mixtures of tungsten carbide and cobalt were ball milled in hexane for 48 hr in tungsten carbide lined mills. After milling, the specimens were pressed in a rectangular die (1x1/4x1/4 in.) at 16 tons per sq in. NO pressing lubricant was used. Sintering of the tungsten carbide-cobalt compacts was carried out in a vertical tube furnace equipped with a dilatometer (Fig. I), by means of which the change of length of the powder compacts could be followed from room temperature to 1500°C. An atmosphere of 20 pct H, 80 pct N was maintained inside the furnace. Decarburization of the samples was prevented by the presence of small rings of graphite inside the furnace tube. The temperature of the sample was measured by a platinum-platinum-rhodium thermocouple, which also was part of a temperature control system able to maintain a constant temperature within ±100C. Pure tungsten carbide compacts were prepared by sintering the carbide without binder or by evaporating the binder from sintered compacts in vacuum at 2000°C. Since complete densification of these samples was not desired, they were sintered only to 60 or 80 pct of the theoretical density of tungsten carbide. The specimens were prepared for metallographic examination by polishing with diamond powders and etching with a 10 pct solution of alkaline potassium ferricyanide. Cobalt etches light yellow and the carbide gray. The amount of porosity is exaggerated since it is difficult to avoid tearing out carbide particles, especially from incompletely sintered samples. Experimental Observations A number of specific experiments were carried out in order to study some particular aspect of the sintering problem. The details of these experiments, together with their results, are as follows: Electrolytic Leaching: The binder was removed by electrolytic leaching from sintered tungsten carbide-cobalt compacts for the purpose of determining the continuity of the carbide phase. The method used was based on the work of Cohen and coworkers4 on the electrolytic extraction of carbides from annealed steels. If the sample is made the anode, using a 10 pct hydrochloric acid solution as the electrolyte, the binder is dissolved, but the rate of solution of tungsten carbide is negligible. A current density of 0.2 amp per sq in. was applied. As shown in Fig.

Jan 1, 1953

By D. R. Bomberger, M. Deul

An automatic microscope has been developed to measure the size and populations of macerals and minerals in fine coal particles. Differentiations are made on the basis of reflectance. This study is concerned with the size distribution of pyrite inclusions. Most fine coal cleaning processes do not remove pyrite as completely as a straight density separation. Consideration of the pyrite size distribution is suggested as a more accurate method of predicting sulfur reduction by a cleaning process. Analyses of float-sink results and Deister Table operation in terms of pyrite particle sizes are made. Other potential applications of automatic microscopy are also discussed. In the study of coal cleaning by pseudo-gravity methods (tables, cyclones, hydrotators, etc.), it is customary to express the deficiency of the process relative to float-sink measurements in some form of "percent efficiency". These have been calculated in many different ways in order to provide a means of extrapolation of test data to untested coal feeds. This works quite well with coarse coal (here defined as larger than one-eighth in.). Large, heavy pieces of refuse are rejected rather thoroughly by many cleaning processes, and the efficiencies relative to float-sink results approach 100%. In coarse coals, the difference in the sizes of fine pyrite is masked by the averaging effect of the large coal envelopes. The existence and fate of fine pyrite is often hidden in the larger numbers representing coarse (and easily removed) pyrite. There are cases where it is desirable to subject fine coal (here defined as smaller than one-eighth in.) to cleaning processes. This is true of naturally occurring fie coal streams and in cases where comminution followed by cleaning is necessary to provide the quality desired. It is in this area that the use of process efficiency relative to float sink fails. Percent efficiencies decline to very low figures, and equivalent separation densities become a matter for conjecture. The net result is that an attempt to estimate product quality from float-sink data and a process efficiency figure often results in large errors. This work represents a new approach to the problem by observing the fate of pyrite particles, grouped by sizes, in a cleaning process. Examples are given which relate pyrite size measurements to float-sink washability and to a Deister Table operation. EXPERIMENTAL WORK The automatic microscope used here has been previously described.' Briefly, it is an instrument which measures the diam of particles (as defined by a range of reflectance) exposed on a polished specimen. The instrument scans a sample briquet, measures diam of exposed pyrite inclusions and records the data by size intervals. Preparation of the briquet is critical, due to the automatic nature of the process. The principal requirement is for an optically flat surface, so that focus will be maintained as the motorized stage moves the specimen under the lens. The various substances present must be polished to the same level in spite of the wide difference in hardness between coal substance and minerals. The polishing method must not pluck out small grains, which might be rather loosely held by surrounding coal. The procedure below was successful in producing all of these results. The coal sample (8 mesh or finer) was riffled (a micro vibrating riffle is essential) to obtain 15 g. One volume of Lucite powder (thermosetting plastic mounting medium) was mixed with three volumes of coal and mixed thoroughly. A briquet was formed using a cylindrical die (1 1/4 in. diam) at 3000 lb per in.* pressure and 150°C. Preparation of the optical surface was accomplished on automatic polishing equipment, according to the following schedule: 1) Grinding: 3 stages, using successively fine Carborundum grits of 180, 320 and 600 mesh. 2) Rough polishing: 2 stages, using 3µ alumina on cast iron, followed by 1µ alumina on lead. 3) Fine polishing: 2 stages, using 0.5µ alumina on napless broadcloth over bronze, followed by 0.1µ alumina on silk filament cloth over bronze. Raw data were corrected for the fact that the chords

Jan 1, 1964

By W. F. Holbrook

THE problem of sulfur control is important in all blast-furnace operations but particularly for certain grades of steel because of the rigorous specifications. During the past decade the tendency has been to produce pig iron, and, hot metal of lower sulfur content. As most of the sulfur in the ion originates in the fuel, the use of high-sulfur coke demands modifications in practice to meet sulfur specifications. While it is generally known that high temperatures and more basic slags favor desulfurization, operators as a rule produce the most acid slag that will permit proper desulfurization. The viscosity of blast-furnace slag has been thought to be related to desulfurization and has been investigated by Feild and Royster1, also McCaffery and his associ-ates2, but apparently no systematic effort has been made to determine the relative desulfurizing powers of slags over the range of composition encountered in practice.

Jan 1, 1936

By Robert L. Gower, John H. Cash

Interconnections for integrated circuits operating at rnicrowaue frequencies rzust be formed as microwave transmission lines. This paper describes the fabrication of one type of microwave transmission line known as microstrip, which can be fabricated on momlithic integvated circuits by deposition of 0.1- to 2.0-mil-thick metal and dielectric films. A microstrip line consists of a narrow conducting strip separated from a gvound plane by a dielectric material. Thick films of good conducting materials are required for low loss at high frequencies. Vacuum-evaporation methods for depositing aluminum and silver films are described. The narrow conducting strip forming the top conductor is defined by photoresist-etching techniques after the thick rnetal film is deposited. Gold plating with a photoresist-masking technique is also used to forrrz thick metal conductors. The microstrip dielectric layer is formed by deposition of suitable dielectric films 0.1 to 2.0 mils thick. Several deposition techniques were investigated. Electron-beam evaporation of quartz is described. Electrical characteristics of deposited microstrip lines at microwave frequencies are included and the microwave power attenuation as a function of conductor and dielectric thickness is given. It is concluded that the deposition of microstrip transmission lines is a practical way to achieve low-loss interconnections in monolithic integrated circuits. CONNECTIONS between devices in low-frequency and digital circuits are usually made by connecting the devices with a length of conductor such as a metal lead oi- a wire. If this method were applied to microwave integrated circuits, the reactance of the connection due to the series inductance and parasitic capacitance would be very high, in fact too high to permit successful circuit operation. In addition, resonance and antenna effects would occur at high frequencies, especially when the connections approach the wavelength.' Connections which are sections of transmis- sion line will overcome these difficulties. The electromagnetic field is confined to the volume of the transmission line, parasitic effects are not present, and circuit design utilizes familiar transmission-line techniques. TRANSMISSION LINES One type of transmission line geometrically adaptable to integrated circuits is known as micrstri. A microstrip line can be generated from a coaxial line as shown in Fig. l(a). The outer conductor of the coaxial line is distorted into an ellipse (b) and finally separated at the extremities of the ellipse to form the strip transmission line shown in (c). One of the ground planes is then removed, leaving a conducting ground plane and a narrow conducting strip separated by a dielectric. Two configurations of the microstrip line were considered in this investigation, Fig. 2. Type (a) is fabricated from a semiconductor slice with the ground plane and top conductor deposited on each side of the slice. The semiconductor slice serves as the die lec-

Jan 1, 1967

By R. I. Jaffee, E. S. Bartlett, D. N. Williams

The oxidation resistance and fabricability of molybdenum powder-metallurgy alloys containing up to 20 wt pct nickel in the form of a fine dispersion were studied. The effects of dispersion distribution and of amount and type (pure nickel or nickel compounds) of additive were considered. A definite improvement in oxidation resistance was observed, but the amount of improvement fell far short of requirements for an oxidation-resistant alloy. Fabricability by hot-rolling was limited. INVESTIGATIONS at Ohio State university1 and Battelle Memorial institute2 have indicated that the attainment of a truly oxidation-resistant molybdenum-base alloy for high-temperature service, with the coincident retention of high-temperature strength and toughness, will be a difficult, if not impossible, feat. Among the most promising alloy systems studied was the molybdenum-nickel system shown in Fig. 1. Alloys in this system show good oxidation resistance at temperatures well above the normal melting point of molybdenum trioxide because of the regenerative formation of protective nickel-molyb-date (NiMoO4) on the surface of the alloy during exposure at high temperatures. Unfortunately, the required alloy content to obtain oxidation resistant molybdenum-nickel alloys far exceeds the limits of the narrow terminal solid-solution boundary, and closely approaches the peri-tectic composition involving the brittle intermetal-lic compound, MoNi. Because of the peritectic reaction, fusion alloys are characteristically brittle, since the MoNi phase, being the last to form, tends to occur as a continuous grain-boundary network around each molybdenum grain. An added problem with this system is that the protective nickel-molybdate layer formed at high temperatures is unstable, undergoing one or more allotropic modifications upon cooling. The volume changes associated with this modification during cooling are such as to cause violent expulsion of the protective molybdate coating from the surface of the piece. This is, of course, quite detrimental in material exposed to cyclic temperature during service. The research reported here resulted from an attempt to overcome the aforementioned problems associated with the molybdenum-nickel alloys primarily by controlling the amount, size, and location of the MoNi phase. By using powder-metallurgy techniques of alloy preparation and sintering the blended molybdenum-nickel powder mixtures at a temperature below the peritectic reaction temperature, molybdenum-nickel alloys with a randomly dispersed MoNi phase were produced. MATERIALS The molybdenum powder used in the preparation of alloys for this study was commercial hydrogen reduced, minus 325-mesh (Tyler) material. Master alloys, by which nickel was added, consisted of elemental carbonyl nickel powder (12 average particle size), an alloy of 50 wt pct Ni-50 wt pct Cr, and compounds of MoNi, Ni,Si, and Ni2B. The nickel-chromium powder was prepared by filing a vacuum-arc-melted ingot, separating impurities magnetically, and screening to minus 200-mesh. The MoNi powder was prepared by pulverizing a hydrogen-sintered powder-metallurgy compact to minus 325-mesh material. Further sizing of this powder for study of effects of dispersion distribution was accomplished by air classification of the minus 325-mesh powder. The Ni2Si and Ni2B powders were prepared by crushing vacuum-sintered powder-metallurgy compacts to minus 200-mesh material. EXPERIMENTAL PROCEDURE Specimen Preparation—The general procedure followed in the preparation of alloys for testing is described as follows: 1) Blending. Either hand-blending of the powders in a ceramic mortar and pestle for X 1/2 or mechanical blending was used. Hand-blending seemed preferable for optimum homogeneity. 2) Compacting. Most of the blended powders were pressed to green compacts at pressures of 15 tons per sq in. in a single-action die, although some were pressed at 80 tons per sq in. A 1 X 11/4 X 1/4-in. green compact was the standard size for oxidation test material, and 7 X 1/2 X 1/4-in. compacts were used for fabricability test specimens. 3) Sintering. All green compacts were sinteredat

Jan 1, 1959

By G. O. Hiers

IN 1948 in the United States, 184,300 tons of lead was fabricated as coverings for electric power and communication cables. Such covering generally is called "sheathing" for the principal lengths of the cables, while the short lead encasements of the joints are called "sleeves." For the purpose of this paper, both lead sheathing and lead sleeving can fittingly be called lead tubing. In the United States in the same year, 34,262 tons of lead was consumed in making extruded lead pipes. Such pipe is employed frequently for water or chemical solution conveyance with gage pressures up to 100 psi. Consequently, the walls are thicker in ratio to diameter than is the case with the cable sheaths. For this discussion, lead pipes can be thought of as tubes or tubing. About 19 centuries ago, the Romans produced metallic lead of about 99.9 pct purity. Evidently this was cast in flat sheets of Y8-in. thickness, for instance. Such sheet of 10-ft lengths was bent around a removable core producing a tube somewhat oval in cross-section and with a typical internal diameter of, say, 3 in. This method of production necessitated a seam or longitudinal joint evidently made by casting the seam metal adherently. The seam metal, as analyzed recently, contains about 1 ½ pct Sn. Blow pipes were said to have been employed when the joint was made. Specimens of such pipe were found both in Italy and in the British Isles. It is believed the pipes conveyed water for drinking purposes and for baths. Numerous specimens are still in existence in a good state of preservation, due to lead's usual inertness in air or water. According to Claude E. Pearson,1 there were various stages in the evolution of lead extrusion presses for making tubes: I. First press by Joseph Bramah, 1797. 2-First successful press by Thomas Burr, 1820. 3-First bridge die press, J. and C. Hanson, 1837. In 1845, Wheatston and Crooke made the first lead sheathed electric cable. Flat lead strip was wound spirally around the insulated conductor. Overlapping edges of lead were soldered. Early cables were also made by pulling insulated conductors into 50-ft lengths of lead tube. Borel in France, and Wesselau are credited with devising the first presses for extruding lead sheaths directly on cables in 1879. In the United States, Eaton, in 188o, and Roberston, in 1885, introduced new presses of improved design. Following Cunningham's original idea of making lead traps and. bends in 1873, the presses apparently were improved and made successfully soon thereafter. Between the years 1930 and 1940, two continuous extrusion presses for lead were developed abroad. One apparently was originated by Dunsheath and made by the Henley Telegraph Works Co. The other was developed by the Pirelli-General Cable Co. CURRENT PRODUCTION In addition to the several descriptive chapters on lead extrusion in Pearson's book, the Metals Handbook2 recently described pipe, sheath, and collapsible tube production. The latter is by impact extrusion.

Jan 1, 1951

By T. F. Bower, M. C. Flemings

Results are reported of a study of surface dendrilic structure of an Al- Cu alloy solidified against a chill wall. Most primary and secondary "arms " in the surface dendritic structure are arranged orthogonally, giving the impression of strong preferred orientalion on the surface. However, no such preferred orientation exists and it is therefore evident the arms do not represent (100) directions. The primary arms are shown to be interseclions of a (100) plane wilh the chill plane, or, equally often. the projeclion of a (100) direction on the chill plane. Secondary dendrite arms are usually within a few degrees of 90 deg to the primary arm, independent of grain orientalion. Prirary, secondary, and higher-order surface dendrite arms almost always represenl intersections of (100) platzes with the chill surace, or pvojections of (100) direclions. Growlh of secondary arms is favored on the side of the primary arm where a (100) direclion points toward the chill surfAce a1 a Lou, angle. Surface dendrile arms are often observed to be bent. In these cases, the crystal lallice changes orientation; bending is concave to the chill surface. In a previous paper,' a technique was discussed whereby large grains can be obtained at a chill surface. The technique used involves quickly drawing superheated liquid A1-4.5 pct Cu alloy into a thin copper mold, so that the mold is full well before solidification begins. The chill surfaces employed are polished copper blocks coated with amorphous carbon. Shrinkage during solidification between dendrite arms and grains delineates both, without the need for polishing or etching of the cast surface. The grain structure of the chill surface was discussed in a previous paper;' in this paper, the dendrite arms within each grain are examined. Previous work on surface dendrites includes that of Edmunds, who studied the development of preferred orientation in zinc, cadmium, and magnesium.' In zinc and cadmium, he found that the surface region has a (0001) texture (parallel to the chill surface). Walton and Chalmers reasoned that, since the fast growth (1010) directions are in the basal plane, nuclei which have this plane parallel to the mold wall would produce larger grains than nuclei with other orientations. Hence, the texture observed is as expected.3 The same authors, in measurements on aluminum ingots, found no preferred orientation at the mold wall. However, the X-ray technique they used measured the preferred orientation in terms of grain numbers, not grain areas; larger grains were weighted equally with small ones. No preferred orientation is expected on this basis at the chill surface. In a later paper,' Edmunds stated that experiments show a random grain orientation at the surface in die cast aluminum; his technique, also used in his earlier paper, takes account of grain area. Little work has been published on the dendritic structure of metal chill grains. Recent work of Biloni and Chalmers on "predendritic growth" shows the change in morphology from spherical to dendritic during the initial stages of freezing, 5 but this work did not include detailed examination of the fully developed dendrites. Other pertinent work includes that of Lin-denmeyer, who investigated the growth of ice dendrites. 6 When growth was on a substrate, the dendrite axes were bent. The bend corresponded to a change in orientation of the crystal lattice and occurred in such a way as to align the basal plane to the substrate. DENDRITE STRUCTURE Fig. 1 shows the chill surface of a typical casting poured above the critical temperature necessary to produce coarse grains. A cursory examination of these grains shows that the surface dendrite arms within most of the grains are oriented roughly perpendicular to each other. One is tempted to assume that these are (100) directions and that, therefore, marked preferred orientation exists at the chill face. This, however, is not the case. Each of the grains in the casting of Fig. 1 was separately identified, Fig. 2, and its orientation determined by the Laue back-reflect ion method. Results are given in Fig. 3 and it is seen there that no preferred orientation exists. Even when grain area is accounted for, there is no significant preferred orientation. The relationship between surface grain structure and crystal orientation was then obtained by assigning X and Y axes to the casting surface, Fig. 1, and assigning the same axes to the stereographic projections of each grain. Thus, the visible surface structure could be compared readily with grain orientation. This was done for fifty-five of the grains of Fig. 1. Results of this study on three typical grains are described below, and some general observations given subsequently. Fig. 4 shows the structure and stereographic projection of a grain which lies near the (100) zone (with respect to the casting surface). The X and Y directions are marked on the projection, and the photomicrograph mounted with the same orientation. Poles of the stereographic projection represent crys-tallographic directions in the grain which point out of the casting, toward the chill. Two (100) directions are shown in Fig. 4. A line joining the center of the projection and a pole represents the projection of the pole onto the X-Y plane (chill surface). Two such lines are shown in Fig. 4 (solid lines). A line joining the intersection of a great circle with the circumference of the projection gives the trace of a crystallo-graphic plane in the chill surface; two such traces are shown (dashed lines).

Jan 1, 1968

By P. Duwez, C. B. Jordan

The phenomenon of the change of volume of pressed powder compacts upon sintering is well known in the field of powder metallurgy. Depending upon the metal or metals involved and the pressure used in forming, a compact may, in the course of time of sintering at a given temperature, expand mono-tonically, contract monotonically, or first show a volume change of one sign followed by a change of the opposite sign. It is clearly desirable to have accurate knowledge of the magnitude and sign of the change in dimensions to be expected in any given case, both from the point of view of direct usefulness in the fabrication of parts by powder metallurgy, and from the longer range viewpoint of elucidating the fundamental mechanism of metallic sintering. The present study was therefore undertaken as a first step in acquiring systematic and reasonably quantitative knowledge of the change in density of metal powder compacts during sintering. For practical reasons, copper was selected as the material to be studied first, and its densification followed as a function of temperature and time of sintering in hydrogen and in vacuum. Experimental Procedure The copper powder used was that designated by the manufacturer (Metals Disintegrating Co., Elizabeth, N. J.) as MD-151. This powder was sifted through Tyler standard screens to separate the fraction having particle size range between 200 mesh and 325 mesh, and this fraction was used in all the subsequent work. Compacts weighing about 10 g were then pressed in a 1 in. diam round die, using a pressure of 20,000 psi throughout. Sintering was carried out in commercially built electric furnaces in which the resistance windings are so disposed as to produce a nearly uniform temperature along the axis of the furnace for a length of about 18 in. centrally located. In order to be able to sinter in a controlled atmosphere, a 2 in. stainless steel tubing was inserted in the furnace. Each end of the tube was cooled by a water jacket about 7 in. long, and closed with a rubber stopper. The hydrogen used for one series of specimens was purified as described in Ref. 1. For the other set, a pressure of about 0.5 mm Hg was maintained during sintering by a Welch Duo-Seal Pump. The specimens were heated on square trays made of stainless steel. In placing specimens in the trays, a thin even layer of powdered aluminum oxide was first sprinkled on the bottom of the tray. A copper guard disk about half the thickness of the specimen was then placed in the tray and covered with a second layer of alumina. The actual specimen was then set on the guard disk, and a final coat of alumina sprinkled over the specimen. This technique was evolved for sintering the specimens in such a way as to reduce the influence of unknown extraneous factors to a minimum. If the specimen is placed directly on the tray and sintered, it is found that the resulting shape is that of a frustum of a cone, rather than a section of a right circular cylinder, since friction with the tray prevents the bottom of the specimen from contracting at the same rate as the top. In the arrangement used in these experiments, the guard disk provided a support which shrank at the same rate as the specimen, and the alumina powder reduced to a minimum friction between guard disk and tray, and between specimen and guard disk. The procedure followed in sintering consisted of bringing the furnace to the required temperature, and then inserting the specimen into the central heated portion of the furnace tube in one of the two atmospheres used. At the end of the heating period, the specimen was cooled by bringing it into a portion of the furnace surrounded by a water jacket. These manipulations were carried out without opening the furnace, by means of rods which were attached to the trays and operated through a sliding seal in the rubber stopper. The progress of densification of the copper compacts was studied at 1300, 1400, 1500, 1600, 1700, and 1800°F. At each of these temperatures, a specimen was allowed to sinter for each of the following time intervals: M, 1, 2, 4, 8, 16, 32, and 64 hr. The thickness and diameter of each specimen were measured with micrometers before and after sintering, and each was weighed on an analytical balance after sintering. Results The techniques described in the preceding section were found to give satisfactory results. The specimens were not detectibly warped after sintering, and were usually of uniform diameter (that is, truly round) to within 0.001 in., a very few showing a variation in diameter of ±0.002 in. All specimens were found to have the same diameter

Jan 1, 1950

By W. A. Wall, R. L. Kidd

IN present-day flotation practice, grinding of the flotation feed is carried to extremely fine sizes, 70 to 80 per cent minus 200 mesh being customary. The greatest flotation losses occur in the coarsest and finest sizes, but the losses in the very fine sizes are, of course, much the more important because of the large proportion of fines in the feed. These losses are particularly high in zinc ores so a study of the effect of size on the flotation of sphalerite has been made. The mineral used in these experi¬ments was a pure sphalerite, especially free from copper, from the Joplin district in Missouri. The sizes coarser than 200 mesh were separated by screening, the sized mineral then being deslimed on a Wilfley table. The sizes finer than 200 mesh were obtained by water elutriation as described by H. R. Bradford (M. S. Thesis, University of Utah, 1932) ; particles finer than 6.5 microns could not be obtained with the apparatus used.

Jan 1, 1933

By Fred P. Peters

At first glance this paper may seem unique among those comprising this symposium on designing for powder metallurgy, since it is evidently concerned with everything but Powder metallurgy. This paradox mill be at once resolved, however, when the real Purpose of the symposium meeting is understood—to present factually and objectively the things that can and cannot he done with powder-metallurgy methods, and especially to set forth with brutal frankness the limitations of Powder metallurgy, so that costly over-enthusiasm and misapplication may be prevented. Since much of powder metallurgy's future development (and many of its present disappointments) has been in competition with other and long-established methods of fabricating parts, it is easy to see that its true competitive possibilities in any given case cannot be accurately appraised without rudimentary knowledge of what the competition can do. This paper, therefore, presents a few reminders of things you all know—a background to be kept in mind as you examine the data on each of their specialties given by the authors of the papers that follow. From the standpoint of the design engineer powder metallurgy is often in Competition with one or more of the following: sand casting, die casting, permanent-mold casting, precision investment casting, ma- chined bar stock, screw-machine parts, cold-heading, drop-forging, and stamping and drawing. We will here briefly discuss each of these individually, and set forth so, rough (and therefore dangerous) generalizations about its competitive position, especially with respect to powder metallurgy. Sand Casting Sand-casting of small parts is sometimes an inexpensive method of manufacture, for its raw-material costs (i,e., for gray iron) are the lowest of the various methods and it involves the use of no tools and dies of jewelry quality. its design flexibility— that is, the ability to make complicated, cored and undercut parts in one piece—is about the highest of the competing processes and in this respect it can do many things that are impossible by powder metallurgy. For small castings its production rates may be higher, by using multi-impression molds, than can be achieved with parts of the same size by powder metallurgy. But its labor charges for melting, pouring, patternmaking and molding are comparatively high and the waste it entails in gates and risers is always considerable. Tolerances of sand castings are wide (+1/6 to 1/32 in- per in.) and where precision approaching that of powder metallurgy is required sand castings must be machined to final size, thus increasing their cost. Steel sand castings are more expensive and less precise than iron, and nonferrous the most costly of all.

Jan 1, 1945

By A. Gatti

A dispersion of AI2O3 was produced within chromium by the hydrogen reduction of a solid solution of Cr2U3-A1203. The yesulting powder. was compacted, extruded, and the material tested in tension at various temperatures and in creep at 1800°F. The material is ductile above 1200°F and is at least twice as strong as electrolytic chvomium at all temperatures. Its creep resistance, rupture strength, and ductility at 1800°F warrant further work to improve its Low -temperatutre properties. BECAUSE of its high melting point and excellent corrosion resistance, chromium has long been considered as a base for high-temperature alloys. Most chromium base alloys, however, are extremely brittle at low temperatures. Elements such as nickel and iron lower the melting point of chromium and thereby limit its high-temperature usefulness. Chromium-alumina materials made by othersl, 2 have shown good high-temperature creep resistance but poor ductility and thermal shock resistance. Pure ductile chromium3 is weak at high temperatures and reverts to a brittle state if exposed to nitrogenous atmospheres. In sintered aluminum powder (SAP)4 and internally oxidized alloys of silver, copper, and nickel, fine dispersions of oxide phases can control hardness, recrystallization, and yield stress. The possibility of formation of a ductile, high-strength material by precipitating dispersions of alumina in a chromium matrix appears worthy of investigation. MATERIAL Powder Production—Chromium oxide and alumina in amounts to produce a final alloy of Cr + 16 pct AI2O3 by weight were colloid milled, filtered, dried and high fired for 16 hr at 1600°C in air. The resulting solid solution of oxides was ball-milled to a fine powder and the chromium oxide reduced to chromium by heating in pure dry hydrogen for 64 hr at 1400°C. Final Materials Produced by Powder Metallurgy Techniques—-Chromium powder, containing a disper-sion of alumina, was pressed into 1 1/8-in. diam slugs at 25 tons per sq in. and sintered 16 hr at 1400° C in pure dry hydrogen. The sintered slugs were encased in a stainless steel can, 2 in. in diam, and extruded at 1200° C through a 1/2-in. die. The 16 to 1 extrusion ratio produced a final chromium-alumina rod 1/4 in. in diam about 30 in. long. Samples of the rod were plunge-ground to small rupture bars of 0.82-in. gage length with a 0.01-sq-in. cross section. RESULTS Microstructure Studies—Fig. 1 is the microstruc-ture of the material in the as-sintered condition while Fig. 2 is the microstructure of the material as-extruded. Comparison of the as-sintered and as-extruded micrographs show the redistribution and realignment of the alumina inclusions by the extrusion

Jan 1, 1961

By G. D. Cremer, J. J. Cordiano

ALUMINUM powder is a well-known article of commerce and in various forms has been marketed widely for use in paint, for pyrotechnic purposes and for exothermic mixtures. For a number of reasons, how- ever, aluminum powder has not been employed extensively in powder metallurgy, although a great many proposals along this line have been offered. Aluminum and aluminum-alloy powders oxidize readily upon exposure to air and the thin film of oxide (or hydroxide) thus formed is highly refractory, in that ordinary gaseous reducing agents such as hydrogen or carbon monoxide do not reduce the oxide to metal at temperatures below the melting point of aluminum. It has been thought that the presence of these films of oxide on aluminum particles would interfere markedly in powder metallurgical work and a number of suggestions have been made, either for preventing the formation of the film through the production of the powders in inert or reducing atmospheres, or for the removal of the oxide by means of powerful reducing agents, including "nascent" or atomic hydrogen released from metal hydrides. 4 second and more serious difficulty in the use of aluminum and aluminum-alloy powders in powder metallurgy resides in the fact that during compression such powders tend to adhere or cold-weld to the die walls, thus interfering with the formation and ejection of a compact. A third difficulty, which has been encountered only with aluminum-alloy powders, is their hardness when compared with elemental aluminum. Certain of these powders are susceptible to age- hardening, which further hinders the formation of strong green compacts. These conditions are particularly true of atomized aluminum-alloy powders. Even in the annealed condition, plastic deformation of alloy powders under pressure is low when compared with unalloyed powders. This fact, coupled with the lower corrosion resistance of the alloy powders, is probably the significant factor in our failure to obtain strong sintered pieces. METHODS OF PRODUCING THE POWER Many methods have been proposed for manufacture of aluminum powder, only a few of which are used commercially. Several of the more important processes include: (I) atomization of the molten metal; (2) mechanical pulverization and other types of comminution; and (3) graining, in which molten aluminum is stirred during freezing. For pigment and certain pyrotechnic uses aluminum flake powder is desirable, because of its greater proportion of surface to volume; and large quantities of such material are made by a procedure that involves stamping or ball milling. In making flake intended for use as pigment,

Jan 1, 1943

By R. M. Waterstrat, E. C. van Reuth

BINARY- alloy phases having the A15-type crystal structure have been described as occurring at a simple and more or less invariant stoichiometric composition (A3B) which corresponds to the relative number of atoms occupying each of the two crystallographi lattice sites in this structure.1,2 It is frequently assumed, therefore, that each crystallographic site is occupied exclusively by one kind of atom. In most cases, however, there have been insufficient experimental data to establish whether atomic ordering is, in fact, complete. Recent studies have shown that binary A15-type phases are sometimes stable over an appreciable composition range3''* and, occasionally, the composition range of stability does not even include the "ideal" A3B stoichiometric composition.5-7 We have observed the existence of nonstoichiometric A15-type phases in the binary systems Cr-Pt and Cr-Os. This has not been reported in previous work on these alloy systems.1,8-11 A series of alloys, each weighing approximately 30 g, was prepared by are-melting in an Ar-He atmosphere using 99.999 pct Cr, 99.999 pct Os, and 99.99 pct Pt as starting materials. Each alloy was melted four times with a total weight loss of less than 1 pct. The stoichiometric (A3B) alloys were sealed in evacuated quartz tubes and annealed at 1200°C for periods of time ranging from 3 days to 2 months. Examination of the alloy microstructures revealed that little change had occurred over this time interval and it was therefore assumed that the microstructures were fairly representative of equilibrium conditions. No evidence of contamination was observed although there was apparently some loss of chromium which was confined to a thin layer at the surface of the specimens. The quartz tubes were quenched from the annealing temperature into cold water. X-ray diffraction and metallographic examination of the stoichiometric alloys revealed an estimated 10 to 30 pct of second phases which were tentatively identified as phases previously reported in these binary-alloy systems.8-11 A second series of alloys was prepared by mixing -325 mesh metal powders having a nominal purity of 99.9 pct and compressing these mixed powders in a cylindrical die at a pressure of 43,000 psi. These alloys, each weighing 15 g, and some of the arc-melted alloys were annealed in a high-temperature vacuum furnace heated by tantalum strips at a pressure of 10-8 Torr and were rapidly cooled by turning off the furnace power. X-ray and metallographic examination of both series of alloys served to establish the composition ranges of the A15-type phases. Although some chromium losses occurred during the vacuum annealing, they were largely confined to a thin layer on the outer surfaces of the samples. It was established that the A15 phases occur in the Cr-Pt system at 21 ± 1 at. pct Pt after 1 week at 1200°C and in the Cr-Os system at 28 ± 1 at. pctOs after 1 day at 1400°C (see Table I). We also observed that an arc-melted stoichiometric (A3B) alloy in the Cr-Ir system was single-phase (A15-type) in the "as-cast" condition in agreement with previous work.8,13 In addition we obtained a sample of the Cr-Os A15-type phase from Argonne National Laboratory. This alloy contained less than 1 pct second phase12 and was submitted to a density measurement. The density measurement yielded a value of 11.14 g per cu cm in comparison to a theoretical value of 11.25 g per cu cm calculated using the observed lattice constant (4.6806Å) of this alloy. The uncertainty in measurement was 0.1 pct but the sample may have contained some cracks or minor imperfections which could account for the low experimental value. We have also studied the atomic ordering in these phases by means of integrated line intensity measurements using thick, flat, rotating powder samples and CuK a radiation in an X-ray diffractometer. We have obtained order parameters of 0.90 for the Cr-Pt phase, 0.89 for the Cr-Ir phase, and 0.64 for the Cr-Os phase using the formula: where s is the usual Bragg and Williams order parameter, ra is the fraction of chromium atoms in A sites, and FA is the fraction of chromium atoms in the alloy. The values obtained are estimated to be accurate within ±4 pct. If the unusually small value for the order parameter of the Cr-Os A15 phase were due to the existence of lattice vacancies on the "B-atom" sites, then a density of 10.04 g per cu cm would be expected in contrast to the observed value of 11.14 g per cu cm. We, therefore. conclude that the fraction of lattice vacan-

Jan 1, 1967

By H. A. Baumann, A. J. Rostosky

EVER since the first installation of wet-washing methods of coal preparation, the removal of the water added by the washing process has created serious technical and operating problems. The rapid development and widespread adoption of wet washing has necessitated a corresponding development of dewatering methods and equipment. The amount of water retained by coal varies with the size of the coal. The moisture that is largely on the surface of the particles is easily shaken off coarse coal; thus coarse coal can be dried comparatively easily and quickly. Fine coal presents a larger surface area than does coarse coal, so its capacity for retaining moisture is greater. In fine coal, moisture below about 5 per cent is held between the coal particles and its removal is difficult. Draining and drying of the finer sizes is a major problem at many washeries. Two common problems of coal-washing practice that are intimately connected with dewatering and drying are the clarification of washery water and the prevention of stream pollution. The first field has been studied from many angles, including the use of coagulating and settling agents followed by vacuum filters to remove the solids, and the use of sludge tanks with dewatering screens incorporated therein. In many districts, the disposal of sludges into streams has been stopped by law. The lack of space for impounding sludges has created problems of disposal in other districts. Reduction in moisture means a saving in freight costs as well as the elimination of difficulties in unloading and storing. Excess moisture in coal causes it to freeze in localities where severe climatic conditions pre¬vail. Excess water in coals to be used in the production of coke and manufactured gas has a chilling effect on the walls of the oven or retort. Dryness of coal is important in producing good briquettes.

Jan 1, 1943