Search Documents

By E. F. Adkins, R. I. Jaffee, C. T. Sims

The effect of oxide dispersions on mechanical proberties of cobalt and cobalt-base powder-metallurgy alloys was investigated. This study shows that oxide dispersions added to pure cobalt greatly improve the high-temperature creep resistance of the metal. Dispersions in powder-metallurgy .cobalt alloys were muck less effective. COBALT is extremely valuable as an alloy base for certain high-temperature applications. Important examples may be found in the widespread use of cast and workable alloys in aircraft gas-turbine engines. With the increases in cobalt production in recent years, greater use may be made of cobalt-base alloys for high-temperature applications, provided

Jan 1, 1960

By C. R. Kyle, R. L. Perrine

A transparent model of a reservoir has been used to study some characteristics of instability in miscible displacement. The linear model dimensions are 1/4 in. x 91/2 in. x 10 ft. The model is packed with spherical glass beads. Thee groups of experiments have been performed. The objectives were to measure, respectively, the rate of growth of the transition zone, flow velocity variations in the transition zone, and the effect of a graded viscosity zone on stability. All experiments were compared, where possible, with theory. The transition zone grew almost linearly with distance traveled, regardless of flow rate, where adverse viscosity ratios were used. At very adverse viscosity ratios and large distances traveled, some reduction below linear growth was noted. This could be attributed to the effects of mixing. General similarity in flow pattern was commonly shown in different tests, although exceptions occurred at the higher viscosity ratios. Injection of tracer spots permitted direct experimental measurement of velocity variations. Statistical methods were used to compare observed velocity variations with recently published theories. Surprisingly good agreement with some theoretical predictions was obtained. In the experiments using an initially graded viscosity zone, macroscopic stability was reached before predicted by theory. Under conditions theoretically considered to be slightly unstable, any fingering tendency was too slight to become observable within a 10-ft long system. The general correlation of all experiments with published theory was good, and suggests that theoretical predictions can be extended to reservoir problems. INTRODUCTION Early laboratory studies of miscible displacement demonstrated the high recovery efficiency possible with this method. Linear laboratory models showed that, under some circumstances, all in-place hydrocarbons could be recovered using as little solvent as 5 per cent of the pore volume. These results led to a series of pilot field projects. Under realistic conditions, however, other laboratory studies showed that a small solvent bank may not recover much more oil than a conventional gas drive. The cause of this lack of efficiency is unstable viscous fingering. The size of the solvent bank required to give optimum recovery is, therefore, a question of great economic significance. The object of the experiments described in this paper was the quantitative measurement of unstable flow parameters, the verification of present theories on the miscible displacement process, and correlation of these theories with ex peri mental observation. Of the theories which have been advanced, those by Dougherty, Koval and Perrine show promise of predicting reservoir performance with reasonable accuracy.l-7 The present experiments were correlated, where possible, with the theories of Koval and Perrine. Dougherty's theory was not used because of the additional computational difficulty it presented and the belief that no further information would result. EXPERIMENTAL EQUIPMENT A transparent reservoir model, consisting of a vertical reinforced plexiglass column, was used for the experiments. The column was packed with glass beads, which served as the porous medium. To induce a known velocity disturbance in the flow, a double cosine wave restriction in the transverse cross-section was placed at the top of the column. To mark the flow field and provide a means of measuring the local fluid velocity, a dye-spot injection system was provided. The column was 10 ft high by 1/2 in. wide by 1/4 in. deep. The cosine restriction was placed 16 in. from the top of the column. The glass beads were smooth and spherical and had a mean diameter of 0.0102 cm. Liquids entered the top of the column through a manifold allowing three points of entry (left, center, and right, or any combination of these). A positive-displacement pump with variable-speed drive was used to control liquid flow rates. The pump transferred viscous oil from a reservoir to an accumulator, which displaced the test liquid into

Jan 1, 1966

By S. K. Mitra

A refinement of the Seeger model for intersection process is investigated which is in better agreement with experimental observations than the original. It is shown that, in single crystals, the strain hardening in Stage II is mainly due to the short-mnge interactions when intersection is the rate-controlling process. It is also demonstrated that the creep curves, as predicted by this theory, are in good agreement with the experimental observations. MOTT: Cottrell? and Seeger have developed an approximate theory for plastic deformation of single crystals over the range of variables where the strain rate is controlled by the rate of intersection of dislocations. Although it is now generally agreed that the low temperature deformation of many pure metals is controlled by the intersection mechanism, various dictates of the over-simplified Seeger model are not in good agreement with all the experimental facts. It is the purpose of this paper to reveal that by appropriate extensions of the Seeger model, particularly those suggested by Basinski: a much more reliable theory results. The refined model to be presented here will be shown to account, in a satisfactory way, for the effect of stress, temperature, and strain on the creep rate under constant stress and for the effect of temperature and strain on the flow stress in constant strain-rate tests. EXPERIMENTAL METHOD To Check the theoretical deductions, both creep and tension tests were conducted on single crystals of high-purity Al (99.994 pct Al) so oriented that both the active slip plane and the Burger's vector of the operative dislocations on that plane made angles of about 45 deg to the tension axis. Single crystals of aluminum (5/8 in. by 1/10 in. by 8 in.) were grown in a graphite mold under an inert atmosphere using the Bridgman method. The chemical composition of the aluminum is given in Table I. A common seed was used for all crystals and their orientation is shown in Fig 3. The extensometry consisted of two differential transformers with matched outputs mounted so as to measure the extension in a 2 in. gage length. The amplified difference in output of the two transformers was recorded by a potentiometer. The amplification was calibrated before each run so that one chart division of the recording potentiometer indicated a 105 shear strain on the specimen. Stresses were measured to the nearest 1 x l04 dynes per sq cm. ACTIVATION VOLUME The concept of Basinski that the activation volume is not constant but is a function of the force that aids thermal fluctuation in effecting the cutting of dislocations will be adopted in this section. The force acting due to an applied shear stress on the dislocation being intersected is where L is the mean spacing between the forest dislocations, is the Burger's vector and T is the back stress. A detailed discussion about the origin of back stress will be taken up later in this report. As shown by Basinski, the activation energy, U, that must be supplied by a thermal fluctuation in order to effect intersection, is equal to where x is the distance through which the dislocation must be translated for complete intersection, and Fm is the maximum force encountered in intersection. When the applied stress is decreased abrupt ly F also decreases and the activation energy increases correspondingly as documented in Eqs. [ 1 ] and [2]. The Seeger equation for the strain rate when the deformation is controlled by rate of intersection of where the shear strain rate (per sec) N = the number of points per unit vol at which intersection can take place

Jan 1, 1962

By F. W. Jessen, G. F. Sears

Cavities in massive salt for the purpose of storage of liquid hydrocarbons have assumed a prominent position in recent years. This paper describes a program to facilitate leaching operations for the formation of specifically shaped storage cavities. Various forms and sizes of cavities may be possible through use of the techniques developed. INTRODUCTION The creation of large under ground storage facilities for natural gas and liquified petroleum gases has been practiced for many years. Use of cavities obtained through solution of salt for this purpose is a fairly new and novel approach, but has gained increasing importance due mainly to the economics of this type of mining operation opposed to hard rock mining or surface and pit storage.1 The idea of controlling the shape of any cavity dissolved from massive salt has not been a prime consideration of companies engaged in the formation of storage space. This has been due mainly to an insufficient knowledge of the mechanics of the leaching process and a dearth of published information dealing with both the desirability and ease of control possible for this type of operation. Two distinct advantages are readily ascertainable. From a stability standpoint (i.e., the ability of the completed cavity to withstand stress imposed by overburden pressure and lateral tectonic stresses) a controlled cavity may be generated which will yield the most favorable attitude to these external forces and remain in operable use for longer periods of time.2 A second advantage is that for a given volume, a sphere (which is one controlIed shape possible) represents the minimum surface area exposed. This may become more important in the future when dealing with refrigeration and product losses in underground cavities. The basic solution mining process, without regard for controlling the final shape, is quite simple in that the equipment and materials required to dissolve a cavity in a salt dome or layered salt section are a source of fresh water, a circulating pump, several strings of tubing and a means of disposal of the return brine. To add control measures involves the use of an inert blanket material above the position at which solution proceeds. Initially the annulus of the largest wash pipe is filled with this blanket down to the top of the proposed cavity. The bottom of the proposed cavity is determined by the depth of the original drilled hole or a blanking plug. The blanket material is added incrementally in stages and displaces the water in the enlarging cavity downward. Where the blanket material has displaced the water, no further solution takes place. The rate at which to add this controlling blanket material so as to be able to form specifically shaped cavities of any particular size is of considerable importance. THE PROBLEM It is desirable to have as much information as possible as to the behavior of the mining operation since visual observation obviously is impossible. It would be advantageous, for example, to have a step-by-step program showing how much salt is to be removed, at what rate and the time required. This type of program would facilitate procurement of surface equipment and provide for proper management of manpower requirements, as well as yield a host of intangible benefits. As mentioned earlier, only rule-of-thumb estimates were available until recently and made this type of pre-planned operation haphazardous at best. Recent work3-' has done much to clear up the ambiguities and inaccuracies attendant to solution mining of salt and has helped to place the operation on a more scientific basis. This study attempts to correlate much of the information thus far developed into a complete mining program; to extend the idea of controlled solution mining to include not only spheres, but solid conic sections of the ellipsoidal variety; and to refine the computation of the rate of removal of salt during the various stages of mining. Dommers3 and IIemson4 made extensive laboratory

Jan 1, 1967

By F. C. Bond, J. T. Wang

H. J. Kamack (E. I. du Pont de Nemours & Co., Inc., Wilmington, Del.)—Rittinger's law usually is stated to the following effect: "The work (or energy) consumed in particle size reduction is proportional to the new surface area produced." The law has been stated substantially in this way by Taggart20 Berry21 Dalla Valle22 Coghill and DeVaney,23 Richards and Locke," Gross,25 and many others, and, according to Gaudin,26 was originally expressed by Rittinger in the same form. Consequently there can be little doubt that this is the understanding of the law among most workers in the field of particle size reduction. Bond and Wang, however, express the law in the form "the useful work accomplished . . . ." (italics theirs). The distinction is critical, for in the form used by Bond and Wang the law becomes, as they themselves remark "merely a more or less arbitrary definition of useful work," while in its usual sense the law expresses a physical hypothesis which has been verified experimentally within certain limitations. Considering the way the law has been used, it might be stated more explicitly as follows: "In a given machine operating under a given set of constant operating conditions, the work consumed in the particle size reduction of a given material is proportional to the new surface area produced." Or, as Coghill and deVaney have said,27 "the (Rittinger) law holds only when the tests being compared are made under analogous conditions." There are occasions when the law transcends these limitations; for example, the surface area produced per unit energy consumption for a given material in a ball mill does not vary much over a fairly wide range of operating conditions. But by and large, the surface area production per unit energy consumption will vary with the operating conditions, the type of machine, and the material. The essence of Rittinger's law is that the surface area production per unit energy consumption is independent of the particle size, and this has been verified experimentally by numerous workers for numerous materials, within certain limits. An important limitation is that when one grinds to very small particle sizes, agglomerative forces may tend to interfere with size reduction so that the surface area increases less rapidly than Rittinger's law would predict. Within such limitations, Rittinger's law can be regarded as empirically established. The law has, however, certain theoretical implications, and it seems to be chiefly against these that Bond and Wang direct their criticism. Solids are believed to possess surface energy which is proportional to surface area. Thus, Rittinger's law implies a proportionality between surface energy produced and mechanical energy expended (for a particular material in a particular machine). It does not imply that all or most of the mechanical energy is transformed into surface energy; in fact it is known that most of the mechanical energy is transformed into heat. Bond and Wang assert that most of this heat arises from the damping of elastic vibrations of stressed particles. This may possibly be true for crushing (with which they are chiefly concerned), although in grinding it is probable that much of the heat arises from friction between particles. However, the fact that the surface energy is small compared to the heat energy does not invalidate Rittinger's law, which implies merely that they are proportional. The authors also criticize Rittinger's law on the grounds that "this theory cannot be justified mathematically, since work is the product of force times distance, and the distance factor is ignored," and "energy input must be the product of force times distance, and the Rittinger theory completely ignores large variations in the distance (strain dimension or deformation) throughout which a force must act to produce breakage of different materials." However, the quantities force and distance as such are irrelevant to Rittinger's law, which considers energy input as an integral quantity. The fact that different materials require different forces and strains (hence, different amounts of energy) to break them is incontrovertible but again is irrelevant to Rittinger's law, which, as mentioned before, applies -only to a single material. Even in theory, it would not be expected that the surface area produced per unit energy consumption would be the same for different materials, because the surface energy per unit area is presumably specific to each material. Bond and Wang advance another argument of a

Jan 1, 1952

By executive order of the President, dated June 25, 1918, the investigation of matters relating to gas warfare, which had been initiated by the Director of the U. S. Bureau of Mines early in 1917, and had been continuously maintained and improved since, that time, was transferred to the recently created Division of Gas Warfare of the War Department. On the occasion of this transfer, both the President and the Secretary of War took occasion to speak most highly of the efficient service that had been rendered by the Bureau of Mines. It gives us great pleasure to reproduce here a letter from the President and from the Secretary of War, bearing on this subject and also to append a brief review of the work of the Bureau of Mines, prepared by its Director, Mr. Van H. Manning. The White House, Washington. June 26, 1918. MY DEAR MR. MANNING: I have had before me for some days the-question presented by the Secretary of War involving the transfer of the chemical section established by you at the American University from the Bureau of Mines to the newly organized Division-of Gas Warfare in which the War Department is now concentrating all the various facilities for offensive and defensive gas operations. I am satisfied that a more efficient organization can he effected by having these various activities under one direction and control, and my hesitation about acting in the matter has grown only out of a reluctance to take away from the Bureau of Mines a piece of work which thus far it has so effectively performed. The Secretary of War has assured me of his own recognition of the splendid work you have been able to do, and I am taking the liberty of enclosing a letter which I have received from him, in order that you may-see how fully the War Department recognizes the value of the services. I am to-day signing the order directing the transfer. I want, however, to express to you my own-appreciation of the fine and helpful piece of work which you-have-done, and to. say that this sort of team work by the bureaus outside of the direct war-making agency is one of the cheering and gratifying evidences of the way our official forces are inspired by the presence of a great national task. Cordially yours, Dr. Van. H. Manning, WOODROW WILSON. Chief, Bureau of Mines, Department of the Interior. War Department, Washington, June 25, 1918. MY DEAR MR. PRESIDENT: In connection with the proposed transfer of the chemical section at. American University from the Bureau of Mines to the newly constituted and consolidated Gas Service of the War Department, which you are considering, I am specially concerned to have you know how much the War Department appreciates the splendid services which have been rendered to the country and to the Army by the Department of the Interior, and especially by the Bureau of Mines under the direction of Dr. Manning. In the early days of preparation and organization, Dr. Manning's contact with scientific men throughout the country was indispensably valuable. He was able to summon from the universities and the technical laboratories of the country men of the highest quality and to inspire them with enthusiastic zeal in attacking new and difficult problems which had to be solved with the utmost speed. I do not see how the work could have been better done than he did it, and the present suggestion that the section now pass under the direction and control of the War Department grows out of the fact that the whole subject of gas warfare has assumed a fresh pressure and intensity, and the director of it must have the widest control so as to be able to use the resources at his command in the most effective way possible. The proposal does not involve the disruption of the fine group of scientific men Dr. Manning has brought together, but merely their transfer to General Sibert's direction. Respectfully yours, NEWTON D. BAKER.

Jan 9, 1918

By K. Sallmann

Spurred by a variety of factors, coal flotation is making headway among the preparation plants of West Germany. The author gives some statistics on German coal flotation plants and information on the properties of the feed and quality of the derived products. Types of machines and reagents used, dewatering practices, tailings disposal, and thickening operations are covered. There is special emphasis on the many-sided problems that confront German coal preparation engineers. The coal mining industry of West Germany is concentrated in three coalfields: the first on the Ruhr and the Rhein rivers, the second on the Saar river, and the third near the frontier between Germany and the Netherlands, around the towns of Aachen and Erkelenz. The total run-of-mine production of these three coalfields amounts to 736,000 tpd which come from 145 collieries. There are 121 washeries, 43 of them with a flotation plant. The total throughput of these 43 washeries is 280,000 tpd, out of which 26,000 tons (9.3 pet of the washery feed coal) are cleaned by flotation. The capacity of the individual flotation plants varies within relatively wide limits, the average being 40 tph and the capacity of the largest flotation plant being 120 tph. During the last few years, the number and size of flotation plants have been steadily increasing, although flotation must be looked upon as an expensive and rather complex cleaning process. The considerations which have led to the widespread application of flotation may be summarized as follows: 1) In making coking coal, it is seldom possible to add uncleaned fines to the coke oven charge, as their ash content is too high. If, however, the ash content of the fines is reduced to a maximum of 7 or 8 pet, they can be admixed to the washed and crushed small sizes without difficulty. This means, naturally that revenue is increased since the price of coking fines is always higher than the price for dust or uncleaned wet fines. 2) To prevent silicosis and pneumoconiosis, water infusion and spraying of the coal are practiced much more today than ever before. As a result, moisture content of run-of-mine coal has markedly increased and the washery feed coal contains more and more slurry instead of dry dust. The price of slurry, how- ever, is very low, and in many cases it is impossible to sell filtered raw slurry with a moisture content of 20 to 25 pct and, at the same time, 20 to 25 pct of ash. Reduction of the ash content of these slurries improves the possibility of dewatering them and, in this way, also enhances the marketability of this product. 3) The new severe laws and regulations against pollution of air and rivers make it necessary to de-dust coal better than in the past and to reduce the quantity of the waste water from coal preparation plants and their solids content to a minimum. 4) Even if there were no compulsory reasons to clean the fines, flotation will often lead to an increase in the overall yield. Although not the only application, it appears that the treatment of coking fines is the primary field for the flotation process in coal preparation. It must not be overlooked, however, that a series of arguments may be advanced against flotation: 1) Flotation is an expensive process because, in addition to the cleaning operation itself, the dewatering of the froth and the disposal of the tailings is very costly. 2) Operation of a flotation plant requires well trained personnel. 3) Filtered froth has about a 20 pct moisture content and, therefore, if mixed with the cleaned small coal it causes an undesirable increase in water content of the coke oven charge. For this reason it is necessary to take additional measures for dewatering washed small coal and this, of course, entails additional expense. 4) Disposal of flotation tailings involves very difficult problems, particularly in the highly industrialized regions. An investigation covering 32 flotation plants of Western Germany shows the following composition and properties of their feed:

Jan 1, 1961

By Pol Duwez

The effect of the rate of cooling on titanium, zirconium, and thallium has been measured. For titanium-molybdenum alloys, it has been shown that for molybdenum concentration up to 8 pct the rate of cooling has no effect on the transformation temperature, but this temperature decreases progressively with increasing molybdenum content. HIGH strength to weight ratio and remarkable corrosion resistance have often been advanced as the main reasons for the present widespread interest in titanium. For the physical metallurgist, the existence of an allotropic transformation in titanium is another important factor. As in the case of iron, an allotropic transformation may be the fundamental property upon which the response of Ti-base alloys to heat treatment will depend. It is therefore important to study the mechanism of the allotropic transformation in pure titanium and the effect of alloying elements on this transformation. The existence of an allotropic transformation in titanium was reported in 1931 by Schulze.' Later, De Boer et al.' determined the transformation temperature from a discontinuity in the electrical resistivity at 882"42O°C. According to recent work," the transformation temperature is 882.5"&1°C. The crystal structure of the room temperature a phase is hexagonal close-packed and the high temperature fi phase is body-centered cubic.' It is well known that the high temperature /3 phase of pure titanium cannot be retained by quenching to room temperature. Several investigators'-' have shown that in alloys of titanium with metals which are soluble in the @ phase (for example, nickel, molybdenum, chromium, or manganese), the /3 structure can be retained, providing the concentration of the alloying element is greater than a certain critical value. Below this critical value, the alloys transform during quenching, at least partially, into a supersaturated solid solution having the a. structure. This behavior is very similar to that found in some iron binary alloys (Fe-Ni and Fe-Mh, for example) and is an indication that the transformation might occur by means of a shear mechanism analogous to that observed in the austenite-martensite reaction. The present investigation is mostly concerned with the effect of the rate of cooling on the /3 to a transformation. In the first portion of this paper, the results obtained on pure titanium are described. Two other pure metals, zirconium and thallium, were also investigated, because they both have an allotropic transformation like titanium, from an hexagonal close-packed to a body-centered cubic structure. For purposes of comparison, the effect of rate of cooling of the y to a transformation of iron was included in the experimental program. The second part of this paper deals with Ti-Mo alloys. The equilibrium phase boundaries involving the solid state reactions on the Ti-rich side of the system were determined and a study was made of the effect of the rate of cooling on the transformation of the high temperature /3 solid solution. Experimental Procedure Since the main object of the present investigation was the determination of the effect of the rate of cooling on a transformation temperature, the best technique available was that used by Greninger" in his study of the martensite arrest in carbon steels. This method consists of heating a very small sample of metal to which fine thermocouple wires are .attached, cooling the sample rapidly by means of a blast of helium, and recording the temperature vs. time curve on an oscillograph. The apparatus used in the present experiments was very similar to that described by Greninger, except that the heating coil was made of molybdenum wire (0.040 in. in diam) and the assembly was placed in a bell jar under vacuum of 10" mm Hg or less. The specimen con-

Jan 1, 1952

By T. Sterry Hunt

Jan 1, 1884

By Lewis M. Haupt

IT has given me great pleasure to read, in the papers recently published by this Society, the discussions on the subject of Technical Education, which were developed at the joint meeting held at the Franklin Institute in June, 1876; and since it was impossible for me to be present, I desire to improve this my first opportunity of adding the weight of my testimony and experience to what has been so ably presented by others. It is a subject about which the people need to be kept agitated, that their views may expand with the demands made for a higher and more thorough education. It is the public at large, the capitalist, the manufacturer, and the laborer, who are to be benefited more or less by this elevation of the standard of our professional schools, and it is but just, therefore, that the schools should look to them for the means with which to accomplish so desirable an object. It is no doubt to the interest of a metallurgist to employ a skilled laborer who will prevent waste by properly proportioning his materials ; by regulating the supplies of air and fuel ; by arranging his plant in the most economical manner, and by disposing of his products to the greatest advantage. The engineer is benefited by selecting for an assistant a person able to determine the values of his factors of safety for the same materials in different forms and positions, avoiding expensive suits for damages and cost of reconstruction; he should be able to so locate a road as best to fulfil the requirements of a through traffic, and yet develop local industries. But I need not multiply instances to show what all will readily concede, viz.: the advantages of a theoretical education ; that was fully demonstrated at the previous special meeting, but it is still an open question whether the practical instruction should precede, accompany, or follow the theory.

Jan 1, 1877

By Russell Webster

In having maintained production for more than 40 years Arizona's Magma mine is unique in a mineral district that includes several major copper mines. Other past and present producers in this area are Miami and Inspiration at Miami, the Old Dominion in Globe, the Ray mine in Ray, and to the south the new San Manuel mine near Tucson. Magma's production of copper, silver, gold, and some zinc has come from nearly parallel east-west striking mineralized faults, one called the Main or Magma vein and the other the Koerner vein, about 1100 ft to the south. This vein system has been prospected and partially mined for some 9000 ft horizontally and 4800 ft vertically. In ascending order from the deepest exploration level, the Main vein cuts Pre-Cambrian schist, Pre-Cambrian Apache Group, Post-Devonian diabase, and Devonian, Mississippian, and Pennsylvania limestones. Until 1950 very little ore was obtained from replacement mineralization.

Jan 10, 1958

Edward Dyer Peters, the only child of Henry Hunter Peters and Susan Barker Thaxter, was born in Dorchester, Mass., June 1, 1849. From his father he was a descendant of the Peters family of Ipswich and Andover, Mass., whose earliest ancestor settled in Essex County in 1659; while upon his mother's side he descended from several old Hingham families, as well as from the Quineys and from Governor Bradford. Between the ages of fourteen and sixteen he was a student at the Episcopal School for boys in Cheshire, Conn. Near the school was an old tin mine, and he used to spend his Saturday afternoons exploring it. When Edward was sixteen, his father sold his property in South-borough, and for the next three years lived in Europe. Sept. 26, 1865, Edward entered the Royal School of Mines at Freiberg, Saxony. In the summer of 1867 he joined his family on Lake Geneva, and spent a part of the season in that vicinity, going to Chamounix and taking other trips. Extract from a letter to his father: Elbingerode, Harz, Aug. 30, 1868: I left Freiberg with my friend Lilienthal, on Wednesday the 19th of August, reached Leipzig in the evening and spent the night in that city: the next morning we took the cars and in the afternoon reached Eisleben, in Prussia, which was to be our first stopping-place; there are immense copper-mines and smelting-works at this place, and the method of working the mines is very peculiar ... The next morning we got up at five and spent the whole day in the smelting-works where I obtained a number of drawings of the furnaces they use here and a good many valuable data. Saturday morning we got up at four o'clock, and descended a mine about three miles from the town; the Director of this mine was one of the most intelligent and agreeable men that I ever met; he accompanied us in the mine and explained everything that was new to us. The system of mining at Eisleben is peculiar to this town, and is not used at any other place in the world; the copper ore comes in narrow, flat veins eighteen inches high, at the utmost, consequently the men work lying flat on their left side and using the pick with both hands: the ore is carried out of the side passages into the main ones, in very low waggons about twelve inches high, and four by two feet; the boys who pull these waggons have a board buckled to their left thigh and their left arm; they pass their bare foot through a strap in the waggon and wriggle along on their side dragging the waggon after them, with their foot, almost as fast as a man can walk above ground. In the afternoon we walked over to Hittstadt, about twelve miles, and remained there Sunday and Monday. Monday night, at ten o'clock we went out to one of the smelting-works, to see the refining of the copper; this is only done at night, so we worked there from ten in the evening till eleven the next morning, and came home all blackened up and with blistered hands, for our skin was not quite so tough as that of the workmen: at noon the same day we took the stage to Ascherls-leben, and then the train to Stassfurt, where there are immense salt-mines, as well as factories for the manufacture of bromium, which latter process is, however, kept a profound secret, so we had very little hope of seeing anything but the salt mines; we were talking with our landlord about our disappointment, that evening, when he told us that the director of the Bromium works was sitting in the next room with no company but his glass of beer, so we went over to him, introduced ourselves as Americans, and actually succeeded in persuading him that it could do his business no earthly hurt if he showed us his works; at last he consented, after making us give our word of honor

Jan 1, 1919

By Henry M. Howe

In discussing the classification of iron to-day, we are to leave out of consideration the general division into non-malleable or cast iron and malleable iron, as to the adequacy of which no question has been raised; and to confine ourselves to the subdivisions of malleable iron. This has been classified, according to the extent to which the properties imparted by carbon are present (viz., resilience, hardness,strength, and, above all, the capacity for being hardened by sudden cooling from a high temperature), into (1) wrought iron which cannot be hardened, and (2) steel which can be hardened; and this classification I shall, for briefness, term the carbon classification. Until within a few years all authorities, both metallurgical and general, have concurred in explicitly recognizing the carbon-given qualities, and preeminently the capacity for being hardened, as the essential qualities of steel; this is laid down with clearness by every writer on the subject. For several years this old classification has not been sufficient to meet all our needs, since the genius of Bessemer, Siemens, and, I may add, Holley, has produced wrought iron which has been perfectly melted, and thus freed from certain mechanical adhering impurities. This causes what we call homogeneousness for want of a better word, and gives rise to many important qualities which the old wrought iron had not; qualities universally recognized, though not readily described. I shall, for briefness, style them the fusion qualities, and a classification based on them, a fusion classification. These qualities render the new product so vastly superior, for most purposes, to the wrought iron formerly known, that it is neces-

By Lewis M. Haupt

IT has given me great pleasure to read, in the papers recently pub lished by this Society, the discussions on the subject of Technical Education, which were developed at the joint meeting held at the Franklin Institute in June, 1876; and since it was impossible for me to be present, I desire to improve this my first opportunity of adding the weight of my testimony and experience to what has been so ably presented by others. It is a subject about which the people need to be kept agitated, that their views may expand with the demands made for a higher and more thorough education. It is the public at large, the capitalist, the manufacturer, and the laborer, who are to be benefited more or less by this elevation of the standard of our professional schools, and it is but just, therefore, that the schools should look to them for the means with which to accomplish so de sirable an object. It is no doubt to the interest of a metallurgist to employ a skilled laborer who will prevent waste by properly proportioning his ma terials ; by regulating the supplies of air and fuel; by arranging his plant in the most economical manner, arid by disposing of his products to the greatest advantage. The engineer is benefited by selecting for an assistant a person able to determine the values of his factors of safety for the same materials in different forms and positions, avoiding expensive suits for damages and cost of reconsiruction; he should be able to so locate a road as best to fulfil the requirements of a through traffic, arid yet develop local industries. But I need not multiply instances to show what all will readily concede, viz.: the advantages of a theoretical education ; that was fully demonstrated at the previous special meeting, but it is still an open question whether the practical instruction should precede, accompany, or follow the theory.

By A. P., Svenningsen

ECONOMICAL handling of a minimum of 25,000 tons of minus 3/4-in. ore per day, grinding it to 2 per cent on 65 mesh, and effecting a high recovery of the copper at the lowest possible cost were the principal aims in the design of the new Morenci concentrating plant. Dealing with a tonnage of this magnitude, it is obvious that lost motion cannot be tolerated. When ore is carried on a conveyor an unnecessarily long distance or elevated to a greater height than necessary, or when pulp flows in a launder by a circuitous route thereby losing elevation and distance, we have lost motion which is always costly both from the standpoint of construction and operation. In addition to the 25,000 tons of ore which must be handled, 100,000 tons of water per day has to be carried through the plant in the treatment of the ore. Though water is not so difficult to handle as the ore, the combined tonnage represents a figure which could easily run into a considerable monetary loss per day if all phases of the design were not carefully followed with the idea of eliminating any unnessary handing of materials.

Jan 1, 1942

By D. A. Elgillani, M. C. Fuerstenau, M. C. Kuhn

The species responsible for flotation when xanthate is added as collector for pyrite is dixanthogen. Measured oxidation potentials of these systems show that xanthate should be oxidized to dixanthogen, and the presence of dixanthogen on the pyrite surface is confirmed by infrared absorption. Zeta potential measurements are presented and related to collector adsorption. In spite of the normal presence of pyrite in most sulfide ore deposits, only a modest amount of study has been devoted to the xanthate-pyrite flotation system in the absence of activators and depressant~.'-~ As a result, little is known about the mechanism of xanthate adsorption on pyrite. From the few studies that have been made, however, a number of significant observations have been forthcoming. For example, the dependence of flotation response on the state of oxidation of the surface was noted in two studies — one conducted by Plante and Sutherland4 and a later one by plaksin.~ In another study, Gaudin and wilkinson3 found that ferric xanthate was not present on a pyrite surface. In a later investigation, however, Gaudin' and his colleagues did extract a small amount of ferric xanthate into benzene when pyrite was ground in an evacuated mill with water, benzene, and xanthate. This quantity was apparently

Jan 1, 1969

By Henry M. Howe

IN discussing the classification of iron to-day, we are to leave out of consideration the general division into non-malleable or cast iron and malleable iron, as to the adequacy of which no question has been raised; and to confine ourselves to the subdivisions of malleable iron. This has been classified, according to the extent to which the properties imparted by carbon are present (viz., resilience, hardness, strength„ and, above all, the capacity for being hardened by sudden cooling from a high temperature), into (1) wrought iron which cannot be hardened, and (2) steel which can be hardened; and this classification I shall, for briefness, term the carbon classification. Until within a few years all authorities, both metallurgical and general,, have concurred in explicitly recognizing the carbon-given qualities, and preeminently the capacity for being hardened, as the essential qualities of steel ; this is laid down with clearness by every writer on the subject. For several years this old classification has not been sufficient to, meet all our needs, since the genius of Bessemer, Siemens, and, I may add, Holley, has produced wrought iron which has been perfectly melted, and thus freed from certain mechanical adhering impurities. This causes what we call homogeneousness for want of a better word, and gives rise to many important qualities which the old wrought iron had not;. qualities universally recognized, though not readily described. I shall, for briefness, style them the fusion qualities, and a classification based on them., a fusion classification. These qualities render the new product so vastly superior, for most purposes, to the wrought iron formerly known, that it is neces- * This paper was read in opening the discussion on the motion to adopt the report of the International Committee on the Nomenclature of Iron and Steel. At the conclusion of the discussion the resolutions on page 44 were adopted.

Jan 1, 1877

By Ira B. Joralemon

The Ajo copper district is in the heart of the Arizona desert, near the western boundary of Pima county. Gila Bend, the nearest railroad point, is 43 miles north of the camp, and the little Mexican border town of Sonoita is 30 miles south. Between Gila Bend and Sonoita, Ajo is the only settlement save for one or two small cattle ranches and the uncertain villages of nomadic Papago families. The Little Ajo mountains rise a few hundred feet above wide desert valleys, beyond which are lava mesas. The camp itself lies at an elevation of about 1,900 ft. above sea level, in a little basin on the east side of the range, separated from the open desert by low hills. In the center of the basin the brilliantly iron and copper stained rocks of Copper mountain rise 150 ft. above the village. Many varieties of cactus and low desert bushes cover the hills, while in the large valleys there are clusters of mesquite, paloverde, and ironwood trees which furnish limited amounts of fairly good fuel. A scanty supply of water is obtained from wells in the desert and from- prospect pits in the camp. The nearest abundant source of water is the Gila river, 50 miles north of Ajo. (See Fig. 1.) , History of the Ajo District The Ajo, next to Senta Rite, New Mexico, is claimed to have been the first copper district in the Southwest worked by Americans. In the '60's or even earlier high-grade native copper and cuprite ore was mined from shallow surface workings and hauled by bull team 400 miles across the desert to San Diego. From there it was carried in sailing ships to Swansea, Wales. Later, the ore was hauled to Yuma, floated down the Colorado river to the Gulf of California, and shipped to Swansea. Bat-infested old workings and the massive axles of the bull carts are shown to prove the truth of the stories. From this early period until the beginning of the present century, the Ajo district was worked only in a casual and intermittent way. With the increased interest in copper mining during the past decade, the brilliant

Jan 1, 1915

By C. A. Herbert

WITHIN the past few years, considerable development has been made in the coal-mining industry in Illinois and Indiana and it is the purpose of the authors to record its most important phases. Perhaps the two most striking features are the entry into the producing fields of certain large consumers of coal and the magnitude of some of the new operations. Mines are now being equipped by the. Chicago & Northwestern R. R., the Chicago,. Burlington & Quincy R. R., the Standard Oil Co., of Indiana, and the Union Electric Light & Power Co. of St. Louis. Besides, the U. S. Steel Corpn. has increased its coal-mining activities by commencing operations on its large holdings northeast of Benton, Franklin Co., Ill. Until recent years, the supply of coal has commonly been adequate and prices have generally been favorable, especially to large consumers, as the magnitude of their purchases enabled them to obtain satisfactory quotations from producers. In fact, most consumers of coal have believed that they could buy their fuel more satisfactorily in the open market than they could produce it themselves. The entry of the United States into the war was accompanied by various disarrangements of industrial conditions, and a demand for coal in excess of the supply seemed likely to be experienced for an indefinite period. Under these circumstances it seemed that the greatest assurance of a supply of fuel was its production by the operation of mines. In the case of the Chicago & Northwestern R. R. and the U. S. Steel Corpn. the production of coal has been carried on for many years with satisfactory results, but the C. B. & Q. R. R., the Union Electric Light & Power Co. and the Standard Oil Co. of Indiana had not been producers of coal, at least in this district. Apparently the most impressive feature of the newest mines is their capacity, for in some cases it is planned that production shall be in the neighborhood of 1000 tons per hr. There are mine, now in this field having nearly that output, but these were not planned for such

Jan 9, 1919

By ROBERT H. BOOTH

THE happy intra-plant relationships of the Bridgeport Brass Co. are largely attributable to the interest of the management in this important business factor. In furtherance of this development Carl F. Dietz, President of the Company and a member of the Institute, has contributed the novel plan for the objective presentation of business economics, described herein. All of the officers of the corporation are active in its management and they together with many other workers filling both executive and subordinate positions have a substantial financial interest in the enterprise. The viewpoint of this organization is fairly reflected by the following quotation from Roosevelt's "The Foes of Our Own Household."

Jan 1, 1924