Search Documents

By Thomas Read

AMONG the large number of deep mines in the world there are several which do not differ much in depth. The St. John del Rey mine, in Brazil, has reached a vertical depth of 6726 ft. below the top of its shaft; miners enter it, however, through an adit which intersects the shaft 324 ft. below its top, wherefore it might be said that the mine is really only 6400 ft. deep. In the Kolar gold field of India there are a number of deep shafts, one of which reaches to a vertical depth of 6140 ft. below surface. In South Africa also there are a number of deep shafts, the Village Deep being 6100 ft. early in 1921. The City Deep, Ltd., proposes to sink to a depth of 7000 ft. but pre-sumably by the time it does so the St. John del Rey will be deeper than that, since it has been increasing in depth at an average rate of about 150 ft. per year. The deepest shaft in the United States, the Tamarack No. 5, although it is only 5308 ft. deep, actually approaches nearer to the center of the earth (4100 ft. below sea level, as against 3958 ft. , at St. John del Rey). The deepest workings in the Calumet & Hecla go down to 4600 ft. below sea level. The St. John del Rey is not only the deepest, mine in the world, but it also is worked by the oldest registered English mining company, which was organ-ized in 1830 to work a mine at a considerable dis-tance from this one. That mine proved unprofitable, and in 1837 operations were transferred to the. deposit now under discussion, where operations have been prac-tically continuous ever since.

Jan 6, 1923

By George Newton

When Mr. Bailey asked us to present a paper describing our new BOF shop, he requested that we avoid a presentation heavily laden with detail and statistics. Not only have we attempted to do this, but also we have prepared a number of colour slides which, hopefully, will provide you with a graphic conception of the facility. The installation of the BOF facility at the Steel Co. of Canada's Hilton Works was delayed many years because of the remarkable production growth of the oxygen open hearth furnaces in No. 3 shop. However, in mid-1960 it became strongly evident that not only would increased ingot capacity be required, but also that N0.2 shop - with vintage non-oxygen open hearth furnaces - would have to clean its stacks in the near future, or be closed down. A decision to embark on the BOF facility was made in 1967 after an extended period of in-depth planning and assessment of industry trends.

Jan 1, 1972

By Jacques B. Wertz

Detailed structural studies in southeast Arizona have successively revealed (1) the local attitudes of individual fractures (with lateral and/or vertical displacements), (2) the patterns exhibited by groups of fractures, and (3) the trends and directions shown by fracture groups or zones on a regional scale. The results of the studies have been twofold: First, domes were locally determined from these fracture arrangements, even where other criteria failed; and, second, fundamental breaks brought out the breadth of the Texas lineament in southeast Arizona as well as major northwest- and northeast-trending fracture zones. Coincidence of one or several domes with the major intersections of fundamental breaks can be centers of important mineralization, as in the instances of Bisbee, Ajo and Morenci. THE OVER-ALL STRUCTURE OF ARIZONA A northwest-southeast trending anticlinorium has been suggested as the structural setting of Arizona. Starting in Triassic and culminating in late Cretaceous times, this deformation resulted from stresses of considerable magnitude with varying ratios of com pres sional and uplifting forces. However, the series of parallel flexures could just as well have been caused by isostatic movements involving dilation under tension with only incidental compression, as later emphasized by dike filling and block faulting (Fig. 1). The anticlinorial deformation, which is also suggested by the fact that the Pre-cambrian rocks to the southwest are all concealed by sediments, could be somewhat reminiscent of the conditions that affected the classical swarm of parallel dikes of wager.' ANALYSlS OF DATA As a first step in this analysis, all structural information obtained on such features as fractures and their relative displacements, faults, dikes, anticlines, synclines, and Precambrian and Laramide-Tertiary intrusives were plotted on maps along with structural trends inferred from aerial photographic mosaics. Next, the faults in southwest Arizona were classified according to time of occurrence and relative importance. The fault assemblages were then examined as to geometric or spatial arrangement and correlated with the occurrences of domes and existing Finally, the conjunction of fracture intersections and domes was analyzed and compared with locations of known ore deposits. Differentiation of Faults According to Time and Relative Importance: The faults encountered were grouped as follows: (1) Basin and Range faults, latest in time; (2) secondary faults; (3) primary faults; and (4) lineaments, earliest in time by inference. BASIN AND RANGE FAULTS- Generally concealed by alluvium, the Basin and Range faults are normal

Jan 1, 1969

By Charles Austin

IT has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent C0 and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their pro-portional limits and yield points are rela-tively low. Published data1 for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the results shown in the lower section of Fig. I. TABLE I.-Analysis of Material I Percentages Constituent Sample Sample Sample 3125 3124 3123 Si 0.25 0.51 o.6o Fe 4.15 10.70 13.17 Ti I.15 3.58 4.70 Mn 0.30 0.41 0.42 Co (by difference)^ 94.15 84.80 81.71 The cobalt from all three samples, united and tested for nickel, gave 0.54 per cent Ni based on the weight of cobalt. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deforma- tion characteristics in moderately long-time tests at 600°, 700° and 800°C. after quenching from various solution tempera-tures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain in- FIG. 1.-EFFECT OF VARYING AMOUNTS OF FERROTITANIUM (FE2TI) ON PHYSICAL PROPER-TIES OF COMMERCIAL COBALT. (C. R. Austin.1) Upper section. Tested at 600°C. after water-quenching from 950°C. Lower section. Tested at 600°C. after water-quenching from 950°C. and aging 72 hr. at 650°C. FIG. 2.-PORTION OF QUASI-BINARY DIAGRAM COBALT-FE2TI AS DETERMINED METALLOGRAPH-ICALLY. formation on the quasi-binary system Cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufac-turing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table I. The alloys, when originally made up,1 were based upon an iron-titanium com-pound, Fe3Ti, as indicated by the work of

Jan 1, 1940

By Charles H. White

METHODS in colorimetry are based on the assumption that the intensity of the color of a definite volume of solution is directly proportional to the quantity of the color-producing substance' present. In the preparation and examination of colored solutions there are three ways in which the depth of color may be varied. These variables are; (1) the quantity of the coloring matter, (2) the quantity of the solvent, or the dilution, and (3) the thickness or depth of that portion of the solution examined. With these three variables as a basis, three general methods in colorimetry have been devised, all of which have been used in the determination of carbon in steel. In the first method, the quantity of the solution is kept the same for both the unknown steel and the standard, and the sections compared are of equal thickness, while the quantity of the standard is varied until the color obtained is of the same intensity as that produced by a definite quantity of the unknown steel. In laboratories where this method is used there is pre¬pared and kept for permanent use a series of solutions with varying amounts of the standard, representing the percentages of carbon from the lowest to the highest demanded in that laboratory. These standard solutions are kept in bottles, or test-tubes of equal diameter, and are arranged in series from the faintest to the most intense color, so that it is a simple matter to find the place of the unknown steel in the series, when the solution is of a definite volume and is contained in a tube of the same diameter as the standard tubes. In the second method, equal quantities of the standard and of the unknown steel are dissolved, the standard is diluted to a definite volume, and the solution of the unknown steel is di-

Sep 1, 1906

By D. R. Parrish, V. J. Berry

Reverse combustion is one thermal method of recovering hydrocarbons from porous undergrortnd formations containing oil or tar. In applying this method, air is introduced via an injection well and the mixture of air and hydrocarbons is ignited in the production well. A combustion zone then recedes toward the injection well, counter-current to the air flow. If the combustion-zorie temperature is sufficiently high, the oil or tar irz place is distilled arid cracked. The hydrocnrhon flows as a vapor to the production well and subsequently is condensed at the surface. Maximum temperature and velocity of morcment arc the two dependent variubles defining the progress of the combustion zone. A theoretical analysis has been made of heat flow in the reverse-comhustion process as.srtrning linear flow in a homogeneous system. The differentirll equatious, which include the oxygen-hydrocar-hon rctrction rate, have been solved numerically. Rescllts indicate that the maximum temperature reached and he cornbustion-zone relocity both increase with an incrense in air-injection rote. Heat loss to surroundings has little effect on the maximum comhustion-zone ten?perature achieved, but it is reflected in a reduced com-bustion-zorzc, velocity. It is also predicted that an increase in the oxygen-hydrocarbon reaction rate results in a reduction in the maximum temperature reached. The calculated results are in agreement with results from reverse-combustion experinments using samples of a tar sand. INTRODUCTION Reverse combustion is one thermal method of recovering hydrocarbons from porous underground forma-tions containing oil or tar.' In applying this method, air is introduced into the underground formation via an in-jection well. In one or more adjacent production wells, the mixture of air and hydrocarbons is ignited at the sand face. The combustion zone thus formed recedes toward the injection well, counter-current to the air flow (Fig. 1). Under certain conditions, the rate of recession of the combustion zone is sufficiently rapid that only a small fraction of the hydrocarbon at any point in the formation is consumed by combustion. If the combustion-zone temperature is sufficiently high, the uncon-sumed oil or tar in place may be partially distilled or cracked. This material then can flow as a vapor with the gaseous combustion products to the production well and subsequently be condensed at the surface. Under other conditions, the combustion-zone temperature may be so low that little, if any, of the hydrocarbon is vaporized. Nevertheless, the viscosity of the hydrocarbon may be reduced enough so that other recovery methods subsequently can be applied to produce oil at attractive rates. The maximum temperature achieved in the combustion zone and the velocity of movement are the two dependent variables defining the progress of the combustion zone. Presumably. knowledge of these factors will permit estimates to be made of oil recovery efficiency, oil and gas producticn rates and average amount of injection air required per barrel of oil recovered. The maximum temperature and combustion-zone vclocity are, in turn, expected to be dependent upon air flow rate, heat losses to surrounding formations, physical properties of the rock and the hydrocarbon. the extent to which the porous formation is saturated with the hydrocarbon, the rate of oxidation of the hydrocarbon and the amount of heat released. It is desirable that the relative importance of each of these factors be understood so that the results of laboratory tests of oil recovery by reverse combustion can be properly interpreted in terms of expected field performance. It is particularly desirable to assess the importance of heat lcsses because these are difficult to control or eliminate

By B. N. Whittaker, C. J. Bonsall

The paper gives an account of the factors influencing the stability of coal mining tunnels and goes on to examine various bases of support and lining design of such tunnels in relation to geological and mining conditions. The different types of coal mining tunnels are compared and comments made regarding the factors influencing their choice and basic design features. Foremost amongst design considerations is the design method and special thought has been given to the validity of different formulae as related particularly to UK Carboniferous geological conditions. Emphasis is placed on the role of the stress field in relation to tunnel stability. Shape of mining tunnel has been investigated and conclusions drawn regarding the merits of different commonly excavated geometries from a stability point of view. Detailed design aspects pertaining to determination of tunnel lining strength and resulting stability are critically examined and current design methods are compared. Data from UK mining tunnels are included as the basis for comparison of these design methods.

Jan 1, 1983

By J. J. Thomas

THIS investigation was undertaken to determine, if possible, the relation between static and dynamic tensile tests as measured by the work required to break test specimens slowly, in a tensile testing machine, and rapidly, by means of a falling weight. It was hoped that the investigation would throw some light on the role played by ductility under different rates of application of load. FIG. 1.-STRESS-STRAIN DIAGRAM. In problems of design, it is usually assumed that the moduli of elasticity of all steels are equal; viz., about 30,000,000. The stress-strain diagram within the elastic limit is a straight line, as shown in Fig. 1, where OA is the curve of a hard steel and OB that of a soft steel. If the modulus of elasticity is constant, as assumed, the slope of the line OC

Jan 2, 1921

By Albert Ladd Colby

PAGE I. Introduction,...........577 11. PRocess of Manufacture. 1. American Specifications. 2. Foreign Specifications, . ......... 580 III. Chemical Properties. I. Chemical Composition: (a) American Specifications ; (b) Foreign Specifications. 2. Chemical Analysis: (a) American Specifications ; (b) Foreign Specifications ; (c) Number of Analyses Required ; (d) Sample for Analysis ; (e) Check-Analyses Impracticable ; (f) Rejection Solely on Variation in Com-' position,............581 IV. Physical Properties. 1. Drop-Test and Drop-Testing Hachine: (a) American Specifications ; (b) Foreign Specifications ; (c) Limits in Deflection. 2. Tensile Test: (a) American Specifications; (b) Foreign Specifications ; (c) Test-Pieces are not Representative ; (d) Specified Tensile Strength is Affected by the Section ; (e) BpeciBed Tensile Strength is Often Inconsistent with Specified Chemistry ; (f) Specified Tensile Strength is Often Inconsistent with Specified Elongation ; (g) Amount of Tensile Testing Required is Excessive ; (11) Conclusions. 3. Dead-Weight Test: (a) American Specifications; (b) Foreign Specifications; (c) Number of Tests Specified. 4. Bending-Test: ((1) American Specifications ; (b) Foreign Specifications,..........589 V. Section. 1. American Specifications. 2. Foreign Specifications: (a) Templets ; (b) Sample Piece of Rail; (c) Allowable Variation from Templet,...........601 VI. Weight. 1. American Specifications. 2. Foreign Specifications,. . 603 VII. Length. 1. American Specifications. 2. Foreign Specifications, . . 604 VIII. Drilling. 1. American Specifications. 2. Foreign Specifications, . 604 IX. Finish. 1. American Specifications. 2. Foreign Specifications, . . 50.5 X. Branding. 1. American Specifications. 2. Foreign Specifications : (a) Data to be Rolled in Raised Letters on Web of Rail ; (b) Marking of the Blow-Number on Each Rail; (c) Additional Marking and Painting of Rails,........605 XI. Inspection. 1. American Specifications. 2. Foreign Specifications: (a) Prior Notice of Rolling; (b) Free Access to the Works ; (c) Cost of Inspection, Analyses and Tests to be Borne by the Manufacturer ; (d) Rails after Inspection by Manufacturer to be Sorted into Lots Prior to Inspection by the Engineer ; (e) Disposition of Rejected

Jan 1, 1907

By R. S. Bradley

WHAT are known as insulating firebrick are lightweight firebrick with low thermal conductivity designed primarily for use in direct contact with furnace gases. These are a recent development in the refractories industry, and are really an outgrowth of the type of insulating brick suitable for use behind refractory walls developed by the insulation manufacturers. To differentiate between these two types of brick, the manufacturers have recently agreed upon the use of the term "Insulating Firebrick" to apply to the type of brick suited for use in direct contact with furnace gases, and the term "Insulating Brick" for the type suitable for use behind refractory walls. Insulation was applied to steam pipes as far back as 1900. This was a low-temperature insulation, the most common type being magnesia blocks. The next development was applying insulation to the outside of furnace walls, a service which necessitated an insulating material of higher temperature resistance. Natural diatomaceous earth, both in the powdered and brick form, was used; this was efficient and is still used extensively for backing up refractory walls where the inner surface temperature of the insulation does not exceed 1600° F.

Jan 1, 1937

By K. Sassa, I. Ito

The dynamic principal stresses induced within rock by an explosion under con fined conditions are analyzed for the case of blasting with one free face by applying the values of measured radial displacement, particle velocity and so on to equations derived from the theory of elasticity. The dynamic stresses on the free face are also calculated from the strain measured by wire strain gauges affixed on the free face. Some results obtained are briefly: 1) The maximum stress on the free face appeared at the intersection between the free face and the burden, and its magnitude was about twice as large as the magnitude of the tangential tensile stress imparted by the incident stress wave within the range related to the breakage by blasting. 2) The maximum value of the compressive stress near the free face was decreased due to the existence of the free face, while that of the tensile stress was increased. 3) At any point near the free face, the directions of the principal stresses in the r? plane using spherical coordinates with the origin at the center of the spherical charge, changed with time except in the direction of the burden. However, at another point near the explosion point where the principal stresses were mainly those stresses caused by the initial longitudinal wave, the directions of the principal stresses coincided with those of the coordinate used. 4) The maximum value of the tensile stress in the F direction was larger than those in the re plane at and near the free face. 5) The tensile stress caused by the Hopkinson effect appeared only near the burden. 6) It is presumed from the results of stress analysis that radial cracks will be produced in the rock mass near an explosion point, but with the approach of the free face, the directions of cracks curve towards a direction parallel to the free face. INTRODUCTION In order to investigate the mechanism of rock breakage by blasting, it is considered to be very im- portant to know how the stresses are generated and distributed within the rock by explosion of a confined charge. As part of a research program concerning the mechanism of rock breakage by blasting, the authors have already published papers on the detonation pressure produced at the inner surface of the charge hole1 and on the behavior of the dynamic stresses within rock caused by an explosion in the case where no free face existed.' In this study the dynamic stresses on and near the free face have been investigated for the case of blasting with one free face. The mechanism of rock breakage in blasting is discussed in the light of these studies.

Jan 1, 1967

By AIME AIME

UNDER the auspices of the Institute's Committee on Industrial Preparedness, a symposium was arranged for the Annual Meeting on the subject "Ores, Metals, and the War," with many well-known Government men and industrialists participating. Wilfred Sykes, president of the Inland Steel Co., of Chicago, presided, with C. K. Leith and Clyde Williams as vice-chairmen, Mr. Williams presiding over the latter part of the meeting. On the Auditorium stage in the Engineering Societies Building was a formidable corps of "experts," with an audience of several hundred to hear what they had to say and to ask questions.

Jan 1, 1942

By I. Havenaar

EXPERIMENTAL DATA In an article by C. K. Ferguson and J. A. Klotz,1 experiments on the filtration of drilling muds under borehole conditions are discussed. Experimental data on mud filtration through the wall and the bottom of the hole are presented. From the data on bottom-hole filtration it was concluded that the filtrate does not flow freely into the formation, but that the pores of the formation are plugged by the mud. A quantitative interpretation of the data can be civen, by using a formula for bottom-hole filtration, dehved below. This formula is based on the following assumptions, 1. Each time a blade of a drag bit, or a cone of a roller bit, moves along the bottom of the hole, the mud cake is completely removed. 3. A new mud cake is immediately formed on the freshly produced surface, and losses of "whole" mud into the formation are negligible (this is equivalent to an immediate plugging of the pores). 3. The filtration of the mud on the bottom of the hole follows the classic law: V = A +1—(Eq. I), where t is the time required to yield a volume of filtrate V, A is the surface area of filter cake, and C is a constant. The application of this equation means that any eroding effect of the mud stream on the mud cake is neglected. The formula for the calculation of the volume of filtrate, Q,, flowing in one second through the hole bottom (diam. d cm), when using a bit with n cones or blades rotating at a rate of rn revolutions per second, is derived as follows: The mud cake is formed on the bottom of the hole in the time t =1; the filtrate volume V which passes n through the bottom In this time 1s given by Eq. 1: After1/nmsec the mud cake is removed. In one m second this process takes place nm times. Therefore the volume of filtrate, obtained in one second is given by This equation has now been applied to the experiments of Ferguson and Klotz. The constants C were derived by means of Eq. 1 from the API filter losses of the muds used by the authors (t = 1,800 sec; A = 45.16cm2). A three-cone bit was used (n = 3) at 90 rpm (m = 1.5). The calculated figures are compared with the experimental data in the table below. The calculated values of Q, are usually lower than the experimental values. This may be due to the following causes. 1. The value of C used in the calculation is based on the API filter test (filtration pressure of 100 psi), whereas the experimental data were obtained with a filtration pressure of 200 psi. Although the effect of the pressure on C is not large, C decreases somewhat with increasing pressure, and this leads to a higher filtration rate. 2. Mud losses and the eroding action of the mud stream on the cake are not entirely negligible. 3. The values of Q, derived by Ferguson and Klotz from their experiments are too high, because of their assumption that all pore liquid within the formation drilled is picked up by the drilling mud. It is found, however, that the calculated values of Qf, except in the case of oil base muds, are of the right order of magnitude. ACKNOWLEDGMENT The author wishes to thank the management of the Koninklijke/Shell-Laboratorium, Amsterdam, for permission to publish this note.

Jan 1, 1957

By H. Foster Bain

Jan 1, 1910

By Ballard H. Clemmons

THE future of the steelmaking industry of the Birmingham, Ala., district is closely related to and, in a large measure, dependent on the development of workable, economic processes of ore concentration. Operations thus far in the area have been possible only because of the fortuitous occurrence of iron ore, fluxing stone, and coking coal-all the primary iron-making materials- within a 25-mile radius of the blast furnaces. Commercial ore of the district consists mainly of a 10 to 20-ft hematite-calcite-silica bed locally known as the "Big Seam," a component of the Clinton formation of Silurian Age. At present mining rates, this ore will be available for a number of years. It is largely mined under 1000 to 2000 ft of cover and transported on 15 to 20" slopes that, in some instances, are as much as 10,000 ft long. Under these conditions, particularly with increasing distances from face to portal, mining costs are gradually becoming disproportionately high. Although not a major factor thus far, it should also be noted that the average annual ore output of the district is gradually be- coming more siliceous.

Jan 1, 1950

[FUQUA, H. B. and Thompson, B. E.: Oil and Gas Development and Production in North Texas for 1933, 107, 320; for 1934, 114, 417 Oil and Gas Development in West Texas 114, 438 FURMAN, W. F.: Heat and Corrosion-resisting Alloys. Printed in Oil & Gas Jnl., June 13, 1935 Furnace-bottom sand, uniformity, 73, 390 Furnace control, Isley apparatus, M27, 502 Furnaces (See also Holt-Dern; Blast Furnaces; Roasters; Wirebar, etc.): annealing: electric, 89, 424 gas-fired, 89, 425 gas vs. wood for nonferrous metals, 89, 422]

Jan 1, 1936

By J. C. Swartz

Measurements of the effect of precipitation stresses on the solubility of cementite (Fe3C) precipitates in a iron are reported. Solubilities were determined from measurements of the Snoek relaxation due to interstitial carbon after quenching from various equilibrium treatments. Stress-free precipitates were obtained by a spheroidizing treatment of vacuum-melted Fe 0.06 wt pet C. Subsequent equilibration treatments were designed to suppress nucleation of other precipitates. The results for stress-free cementite give a heat of solution of 14.8 i 0.2 keal per mole and an entropy change of 1.1 i 0.2 eu in the temperature range 400" to 715°C. Comparison with previous data indicates that the heat of solution increases about 6 keal per mole as temperature increases from 700" to 1000°C. Data on self-stressed cementite in quench-aged specimens of Fe 0.013 wt pet C indicate 1) an apparent heat of solution of 12.1 i 0.4 keal per mole in the range 280" to 690°C, 2) a strain energy of- 1.1 keal per mole Fe3C accompanying precipitation at 280°C, and 3') a gradual decrease in the strain energy of precipitation with increasing equilibration temperature. In com-parison with 2 and 3 the strain energy calculated for an isotropic model is 1.7 keal per mole Fe3C. The lower values obtained from the experiment indicated substantial stress velaxation by dislocation motion. WHEN a supersaturated solution of carbon in a iron is aged at temperatures in the range 200o to 700oC, the carbon clusters by interstitial diffusion and forms cementite (Fe3C) precipitate particles. Unstressed cementite has a volume per iron atom 9 pet higher than that of a iron;' hence, cementite precipitate particles are usually under pressure from the iron matrix. The pressure would tend to increase the solubility of cementite in iron.' This report describes anelastic measurements of the solubilities of self-stressed and stress-free cementite in a iron. Previous determinations of the cementite solubility are summarized in Table I. The method of cementite formation for each reference was studied to ascertain the state of stress of the cementite. The results judged to be for stress-free and stressed cementite are distinguished in the table. In the next section an estimate of the stress effect is obtained which is clearly too small to account for the large difference between the previous results in parts A and B of the table. THEORETICAL Let AGO be the standard free-energy change of the reaction Fe3C (eem.) = 3Fe (a) + C (in a) [1] in the absence of stresses. Since cementite precipitates appear to be rather pure10 and the carbon is so dilute in the iron,8 the cementite and iron of Eq. [ I] for the stress-free case have essentially unit activities and the activity of carbon equals its atom fraction xoC Then the stress-free equilibrium is expressed by RT In XoC = -?GO 121 To first approximation the change in the chemical potential of carbon due to the precipitation stresses equals the elastic strain energy W accompanying precipitation of a mole of cementite.2 Hence, in the presence of the precipitation stresses the equilibrium is described by RT In x sq = -?G° + W [3] where xsC is the mole fraction of dissolved carbon in the stressed case. An approximate value of W can be obtained from analysis of the inclusion problem in elasticity theory. The inclusion is a small portion of the matrix phase which has suffered a transformation while still imbedded in the matrix. In the absence of the constraint of the matrix the transformation would be equivalent to a uniform dilational strain eT. Both the matrix (a) phase and inclusion (0) phase are assumed to be homogeneous, isotropic materials. When the a and 0 phases have the same elastic moduli, which is approximately true for iron and cementite,11 the total strain energy per mole ß is12 2µVß(eT)2(3 +4 µx)-I [4]

Jan 1, 1968

By P. W. Andrews, R. B. Toombs

ECONOMIC STRUCTURE OF MODERN INDUSTRIAL ECONOMIES The role of minerals in modern industrial economies may be examined in several ways. There are relationships with the various sectors of the economy: the primary, secondary, and tertiary industrial groupings and activities. Mineral supply and demand activities can be measured in terms of national accounts criteria. The economic policy objectives of the modem industrial economy are based to a considerable extent on the needs of the nation for economic supplies of miner- al materials. There is an important role for minerals relative to national security in peace and in wartime and many national policies are directed toward ensuring adequate sup- plies of minerals. Environmental control in the modem industrial economy is increasingly concerned with matters related directly to the production and use of minerals and these matters, in turn, bear importantly on conservation in mineral supply and demand. Mineral polices include specific provision for research and development activities concerned with the production and the use of minerals. In all, national policy objectives will be shaped in considerable part by the circum- stances of mineral supply and demand: the relative degree of availability from domestic and foreign sources, the state of the mineral-processing industries, and the degree of development of the mineral-using industries, and per capita and total changes in requirements. Goods made from mineral raw materials are the basis of all advanced societies and although this is taken for granted, every country is continually dealing with problems of mineral supply and demand. Considering that in the first 50 years of this century the consumption of mineral materials in a highly Industrialized country such as the United States increased by six times while the population was doubling, it becomes apparent that if a country is to enjoy rapid economic growth it must have access to huge and ever-growing supplies of mineral materials at lowest possible cost. Adequate supplies of mineral materials and wise usage of mineral resources have always been among the most important determents of a nation's survival The importance of access to adequate mineral supplies is increasing every year and this has significant international, as well as national, implications because of the unique locational characteristics of mineral resources. It is generally acknowledged that no particular type of natural resource is essential to a high level of national income or to economic progress. A country's endowment of natural resources need not exercise a determining influence on the course of its national income over time, provided it is able to trade. What is required for economic progress is the availability of a substantial quanti-

Jan 1, 1976

By Floyd C. Kelley

The literature of the last decade is rich with information relating to the cause and means of control of grain growth in pure metals, but is deficient concerning the role diffusion plays in grain growth, although during this period many new products that depend on diffusion for their properties and success have been developed. Among these are cementation products, produced by calorizing, chromizing, and carbonizing, or by mixing, pressing, and sintering powdered metals such as Syke's iron-molybdenum die material, Genelite, and Elcon Metal (copper, tungsten) etc. This is a fertile field for new developments, but before it can be utilized to the fullest extent there must be a thorough invest,igation of the processes by which diffusion and grain growth take place. Grain growth plays no small part in the process and certainly the physical properties of these products depend largely on the grain size and state of equilibtiuni produced. The field of investigation does not end here, but may be extended to the effect of diffusion on impurities, segregations and dendrites in the broad field of ferrous and non-ferrous metallurgy. A number of years ago the author investigated several of these cases and noted, with striking regularity, the pronounced effect of diffusion in promoting recrystallization and grain growth. An example of this phenomenon is given in his paper on chromizingl which contained photomicrographs of large radial or columnar crystals produced by diffusion of chromium in the solid state. Another manifestation of this effect was discussed by Austen,2 who showed the part hydrogen plays in the decarburization of steel and the effect of diffusion upon the grain structure. Diffusion of Metals in Iron It seems to be a general law, whenever two metals are brought into intimate contact at a temperature at which diffusion takes place, that a comparatively rapid, or abnormal, grain growth results. The grains

By Frank Alfred Fahrenwald

A complete list of the elements as given for 1915 includes 18 that melt above 1,700" C. There does not exist one complete thermal equilibrium diagram for any pair of these 18 elements. Several of these elements have been combined, in relatively small proportions, with metals of lower melting point: e.g., tungsten, molybdenum, and vanadium, in steels, or with nickel and cobalt; but of this refractory group, platinum is the only one that has been extensively studied in this connection. When one considers that, with few exceptions, the industries have made use of alloys to the exclusion of pure metals, it is reasonable to expect that alloys of this refractory group will invade fields in which the pure metals have found little application. The past neglect of this class of metals has, no doubt, been partly due to the rarity of some of them, for even though alloys of very valuable properties should be developed, their cost, unless in exceptional applications, would be prohibitive. There is also a well-founded reluctance to undertake research involving very high temperatures which, in the case of most of these elements, must be accompanied by an inert atmosphere as well. This combination of high temperatures*and control of atmosphere within the heating chamber of any furnace of present design is a difficult problem. It is the purpose of this paper to give results,' of an investigation of one binary series of this group, in which methods were employed that avoided the usual difficulties accompanying high-temperature alloy investigation. , Historical.—The alloys of tungsten and molybdenum have received very little consideration during the past. A review of available literature reveals very little regarding this system, and that which has been recorded seems to be at fault. Mennicke2 writes, "Die bekannteste Verbindung

Jan 1, 1917