Search Documents

By O?Harra B. M.

THE work here described had for its purpose the procuring of data from which some quantitative estimate might be made of the results obtainable by using oxygen-enriched air in roasting zinc ores on a commercial scale. The principal metallurgical advantages of using enriched air in roasting zinc ores would be: 1. The rate of roasting would be increased, with consequent gain in the capacity of the roasting furnace. 2. As less air would be required for roasting, the volume of hot gases leaving the furnace and the heat carried out of the furnace as sensible heat in these gases would be less per ton of ore roasted; partly for this reason and partly because of the increased quantity of heat generated in the furnace by the larger amount of ore that could be roasted, the consumption of fuel by the furnace would be lessened; and by the use of air sufficiently enriched with oxygen the necessity of using fuel might be entirely obviated. 3. Roaster gas having a higher SO2 content could be produced; this would make possible greater capacity and more economical operation of the sulfuric-acid plant. Certain phases of the application of enriched air to roasting can be worked out only by experimenting with a furnace of commercial, or at least semicommercial, size. Thus the precautions necessary to secure proper. distribution of heat in the furnace;1 the volume of enriched air; and the proportion of oxygen in this air, necessary to give the desired increase in roasting capacity of the furnace and in SO2 content of the roaster gases;; and the most desirable frequency of raking, thickness of

Jan 11, 1924

By H. F. Yancy

PooR results in coal washing and in ore concentration are sometimes attributed to the shape of the particles in the feed. It is well known that the shape of a particle influences its rate of fall in water. This is evidenced by the value of the constant C in the Rittinger equation for the velocity V of settling in water, V = C-D(d- z ), where C has the following values: 2.73 for roundish grains, 2.37 for long grains and 1.92 for flat grains. This report, which is based upon data obtained during the course of coal-washing investigations conducted by the U. S. Bureau of Mines in cooperation with the College of Mines of the University of Washington, gives the results of a method or procedure of screening in which the particles are separated into three shapes and shows the deportment of these shapes when coal is treated on a coal-washing table. The method consisted in first screening the coal with Tyler standard square-hole sieves, followed by screening tests of each of these products with screens of rectangular opening. For this purpose Tyler "Ton-Cap" screens were used; each square-hole product was subsequently sized with two Ton-Cap sieves so selected that their shortest dimensions were approximately 75 and 50 per cent., respectively, of the opening of the square-mesh sieves. For example: A product which is through 8 mesh (0.093 in.) and on 10 mesh (0.065 in.) is screened on slotted sieves which have openings 75 and 50 per cent. of the 0.065-in. opening in one direction and an opening of not less than 0.065 in. in the other direction. For convenience in discussion, the particles retained on the first slotted screen are termed "cubical"; those retained on the second slotted screen are termed "prismatic" and those passing the second screen are called "flat." (See Fig. 1.) The square-mesh screens separate particles according to two dimensions, length and breadth; the slotted screens divide them further according to the third dimension, or thickness. Prismatic particles have a mass of about two-thirds, and flat particles of about one-half, that of cubical particles of the same square-mesh size. The screen-

Jan 1, 1931

By James A. Barr

[CONTENTS PAGE Foreword. By JAMES A. BARRI A New Core Barrel for Prospecting for Phosphate in Florida. By I. M. LEBARON 2 Prospecting for Phosphate in Tennessee. By W. F. GUENTHER 6 Machine Prospecting in Tennessee Brown Phosphate. By H. O. PICKARD, JR8 Diamond Drilling through Flint Horizons in Tennessee. By HENDON R. JOHNSTON9] Foreword PROSPECTING methods used in Tennessee have gradually improved with the years, as required by depletion of the easily accessible and shallow deposits and the universal trend toward mechanization, and as necessitated by exploring deeper beds, often occurring under limestone and flinty overburden. In the early days it was a very simple matter to dig pits by hand, using a plentiful supply of local farm labor to expose relatively shallow deposits of "brown rock" under shallow clayey overburden that would stand up without timbering. Visual inspection of the exposed phosphate and expert judgment of the"grade" analysis, aided by a "biting" test to reveal presence of unwanted silica, furnished most of the information required. All this might be helped by a few samples sent to the local chemist[t] who supplemented his income by judicious trading or tanning a few bear skins. The extra curricula activities did not affect the accuracy of the analysis which hold up even under present day standards. Some shot and core drilling was done in Hickman County, mostly for the limestone-like blue Phosphate deposits. The next step was the use of a 4-in. posthole auger, hand operated as described by Guenther, followed by- a completely mechanized rig, as described by Pickard. Both these methods are practically adapted to the prospecting of the relatively soft brown rock deposits at moderate depths of clay overburden. For prospecting in areas of deeper overburden, such as are often found in Hickman County, up to 150 or even 200-ft depths, a modified core-drilling method is described by Guenther. Johnston describes a special diamond-drilling technique, developed by TVA, to penetrate flint horizons, which was adopted by the International Minerals and Chemical Corporation to prospect in Hickman County where deposits had previously been prospected at considerable expense and with difficulty, by Small, temporary, hand-dug shafts.

Jan 1, 1947

By Frank Corwin

I. INTRODUCTION. SINCE the first installation of MacDougall roasters at the Great Falls smelter of the Anaconda Copper Mining Co., the capacity of the furnaces has been more than doubled. During the first nine or ten years of the operation of the MacDougall department the tonnage treated by the furnaces remained practically unchanged. Experimental work carried out in 1906, however, showed that increasing the draft of the furnaces would bring about an increase in capacity. In 1909 the MacDougall department was connected to the new smelter stack and

Jan 7, 1913

By J. E. Johnson

It is the purpose of the present paper, while not excluding chemical considerations, to deal more extensively with some of the physical and mechanical aspects of the blast-furnace process, and to point out its dependence, in these respects, on well-known laws. The quantity and cost of ore and flux required to make a ton of iron being determined by circumstances over which the furnace-man, under given conditions as to quality and quantity of product, has commonly little control, the principal item of cost, apart from the saving of labor, which he can aspire to reduce, is that of fuel. To determine the limits of possibility in this direction is clearly the first step in a practical inquiry; and this step is represented herewith in Fig. 1, a diagram showing the total useful effect obtained from a pound of fuel under various conditions, and thus permitting direct comparison, under any given conditions, between actual results and the maximum possible results. The following statements will explain the basis upon which this diagram has been constructed. One pound of fuel, containing 90 per cent. of fixed carbon (which represents average conditions), is taken as the unit. The degree of oxidation of the carbon is measured by the ratio of the two oxides of carbon contained in the top-gases. It is necessary to remember that a considerable quantity of carbon is brought in as carbon dioxide by the flux, and to take account of it and of its condition. It is here considered that the carbon dioxide liberated by the limestone does not affect the analysis of the top-gases, and that the ratio of CO to CO2 will remain unchanged by the addition of limestone; enough CO, being reduced by the solution

Jan 1, 1906

By F. R. Hensel

Up to the present time few attempts have been made to produce hard nonmagnetic materials by heat treatment of austenitic steels. The usual result has been to cause them to pass into the martensitic stage, thus destroying to a great extent the typical austenitic properties, since this involves a transition of a portion of the iron from a face-centered to a body-centered type of atomic arrangement. High-strength nonmagnetic materials such as might be provided by properly hardening austenite are required in the electrical industry for different machine parts. In Europe nonmagnetic retainer rings for restraining the end-turns of the rotor windings in turbo-alternators have been developed as a special application of high-strength austenite. In testing1 a 28,000-kva. three-phase Siemens turbogenerator running at 3000 r.p.m. at full load current, the losses in the short-circuit test were 450 kw. for the magnetic ring and 286 kw. for the nonmagnetic, and the difference should be attributable to the magnetic ring. The differences in temperatures during the same test are given in Table 1 and these show the advantage of a nonmagnetic over a magnetic retainer ring. Hardening in this case was obtained by cold working, such as hammering, rolling or some means for stretching the steel while at a temperature near 500" C. One means for stretching2 is to rotate the forged or rolled ring in a centrifugal machine so as to develop within it stress higher than

Jan 1, 1931

At the eastern end of the Mesabi Range, 70 miles due north of Duluth, is the vast plant of Erie Mining Co. Operated by Pickands Mather G Co. for the mine's four owners-Bethlehem Steel, Youngstown Sheet and Tube, Inter- lake Iron, and Steel Co. of Canada-Erie Mining Co, has earned just fame as a pioneer and a leader in the mining, beneficiation, and agglomeration of the lean iron ores of the Lake Superior district. Here is the story of Erie and the integrated operations that have made it such an outstanding member of America's iron ore industry.

Jan 5, 1963

By Charles Morgan

An increased demand for brown iron ore in the Birmingham district during the past 18 months has caused renewed activity both in prospecting and mining these ores. In recent years the production in Alabama has ranged from 41,559 tons in 1932 to 639,351 tons in 1928. During the last 9 years about 83 per cent of the total brown ore produced in the United States has come from Alabama (Tables 1 and 2). Prospecting Two methods of prospecting are used in this district: (1) test pits, (2) churn-drilling. Usually there is certain quite definite information on an area to be prospected; some of the indications are float ore such as small gravel or small and large boulders known as "dornicks" scattered over the surface, and ore exposed by erosion in gulleys and ravines, which have cut or eroded through the overburden. Often these natural erosions furnish an indication of the thickness of the ore and to some extent of the area of the ore body. Deposits of brown ore are very irregular both in thickness and extent. Deposits are often lens-shaped or long narrow leads, some of which may be parallel and separated from one another by sand, clay or gravel. The bottom—the footwall—is also very irregular. This footwall is usually lime clay—disintegrated limestone, locally called "white horse," which usually is found at a depth of 6 in. to 20 ft. overlying the limestone. At some places sand and gravel is found under the ore instead of clay. No ore is found under the lime clay, although often the ore has sunk or slumped and is found in the upper portion of this clay, as at some of the Sloss workings at Russellville. The origin of these ores has been discussed by Major E. C. Eckel and Dr. E. F. Burchard in U. S. Geological Survey Bulletin 400, and recently the latter has done further work on ores in the Russellville district, of which reports undoubtedly will be published.

Jan 1, 1940

By Frederick M. Becket

DoctoR Albert Sauveur, distinguished scientist and Honorary Member of this Institute, predicted in the first Howe Memorial Lecture that the privilege of delivering' this annual address would be considered a highly significant honor. The intervening years have well borne out Sauveur's prophecy. I wish to assure the American Institute of Mining and Metallurgical Engineers that I also deeply appreciate this honor, recognizing at the same time the present and even more the future responsibilities with which it is accompanicd. Several of the previous lecturers had the good fortune to attend the classes of Professor Howc and to work in his laboratories. I was similarly favored, although in my instance and to my great regret the period was all too short. However, Howe's book, published in 1903, "Iron, Steel and Other Alloys," afforded me abundant opportunity to continue these studies. How well I remember the inspiration I derived from this famous book by Howe, the metallurgical master, pioneer, and educator! Remembering that Professor Howe contributed numerous papers to The Metallographist, a magazine supported from a technical point of view by the world's pioneers in metallography, I was curious a few days ago to learn the nature of Howe's early contributions to this magazine. The first paper by Howe in the first year of The Metallographist (1898) dealt with the allotropic theory; the second also treated of allotropy, and I quote the first sentence of that paper: The allotropic theory of the hardening of steel may, like so many other important theories, have to be accepted or rejected not on direct proof or disproof, but on the accumulation of circumstantial evidence for or against it. Howe's ability to stimulate others by his deep understanding and clarity of expression was truly remarkable; but just as striking was his intuitive judgment concerning the implications of metallurgical data in the arts and scienees. It therefore seems fitting that this lecture comprise a broad treatment of the subject chosen, rather than a closely documented thesis on any one phase of the problem; that in it attention be focused

Jan 1, 1938

By Chester A. Fulton

In Polk County, Florida, the mining of raw phosphates began some 50 years ago with dredging operations on the Peace River, and in other near-by places by removal of shallow overburden with negroes and wheelbarrows, or with mules and scrapers, and the excavation and screening of deposits found close to the surface. There were many individual operations of comparatively short life. Later steam shovels removed the overburden, and still later hydraulic methods were substituted for the steam shovel. Within the last 10 years large electrically operated draglines have almost entirely replaced hydraulic mining for overburden removal. The matrix is still mined by hydraulic giants and pumped to the washer or recovery plant. The many small operations have long since disappeared and the most desirable phosphate lands have gradually been acquired through purchase or merger by the seven companies that are operating in the field today. These companies are producing and selling about 2,000,000 long tons of phosphate per annum, or about two-thirds of what the industry likes to think is the normal output, with 1929 and 1930 in mind. To produce these 2,000,000 long tons of raw phosphate, they mine and treat about 1,000,000 tons of tailings from older and less efficient operations, about 11,000,000 tons of matrix, and remove from above this matrix some 22,000,000 tons of overburden. The mining practice that has made possible the excavation and handling of 34 million tons of material to win but 2 million tons of merchantable product, selling for probably an average of only $4 per long ton when dried, should be of interest to the mining profession, though little has been written of it. The Florida Pebble Field, as it has come to be known, comprises an area (Fig. 1) within a radius of about 18 to 20 miles centering around Mulberry in Polk County, a small town 30 miles east of Tampa, Florida's largest port on the Gulf coast. The geology1 of these phosphate pebble deposits may be described briefly. A fairly pure limestone was altered to a secondary apatite.

Jan 1, 1938

By Ralph A. Sherman, J. M. Pilcher

BY surface treatment of coal is meant the application of a material, either solid or liquid, to the surface of pieces of coal. The purposes of surface treatment are varied. They may be to identify or "trade- mark" the coal, to modify the burning characteristics, the coking tendencies, or the behavior of the ash, to prevent the freezing of wet coal, or to control the dust. The control of dust is the usual purpose of surface treatment. TRADE-MARKING COAL The application of color to the surface of coal for the purpose of identification and registration of the trade-mark has been practiced to some extent. In 1928, the Glen Alden Coal Co. began to color its coal and adopted the trade-mark, "Blue Coal." The Old Ben Coal Co. later followed a similar practice with "Green Coal." A commoner means of identification of coal has been the stenciling of designs or pasting labels on large lumps or in the distribution of small cardboard tags through the smaller sizes. The details of the method used to color coal have not been revealed. Usually all of the coal is not treated, because of the expense. Only enough pieces are colored to show clearly when distributed through the coal. The patent literature gives information on some of the methods proposed. Esselen and Weiss have patented the deposition of a coloring material in the valleys of the surface of the coal. Sperr covers the quenching of coke with water containing a pigment or dye that will deposit on the coke. He also suggests electroplating with copper or nickel. Glinsmann subjects the freshly fractured coal surface to the action of an alkali or alkali earth ferricyanide and a ferric salt. Barsky and Hanson specify a method for the application of the same chemicals covered by Glinsmann. COATINGS FOR IMPROVEMENT OF APPEARANCE As a purchaser often judges coal by its appearance, modification of the surface has been attempted from time to time, particularly of the surface of outcrop or stored coal, which has become covered with a brown film of iron oxides, but information is lacking as to the extent or success of the

Jan 1, 1950

By J. S. Bryner

INTRODUCTION IN the study of metallographic specimens in the electron microscope, there is need for a method of locating the same field in both the light microscope and the electron microscope. This need arises chiefly from the fact that in the electron microscope the magnification and degree of resolution are so much higher, and the field so much smaller than in the light microscope that it is often difficult, if not impossible, to identify positively what is being observed. The difficulty is increased by the fact that, because a transparent film replica of the metal surface must be used in the electron microscope, micro-constituents can be identified not by their color but only by their texture and contours. For these reasons it is desirable to obtain a series of photographs showing the same field in both microscopes in order that the appearance of common microstructures and micro-constituents in the electron microscope may be identified and catalogued for future reference. The need for a method of locating the same field in both microscopes arises also when it becomes desirable to enlarge in the electron microscope for more detailed study a particular interesting structure observed in the light microscope. Using the standard polystyrene-silica1,2 replica technique, in which the silica film replica is fished from the ethyl bromide on a 1/3 in. diam 200-mesh specimen screen, the possibilities of locating a particular area on the film in the electron microscope are rather remote. The desired structure may be obscured by the wires of the specimen screen or unrecognizable at the high magnification. A solution to the problem would be provided if a specially designed specimen screen, containing an opening which could be absolutely identified and quickly located in the electron microscope, could be fastened to the silica film replica in such a position that the desired field on the specimen would be located at the identifiable opening in the specimen screen. The design for such a specimen screen, a method for producing it, and a technique for fastening it to the silica film replica are described below. DESCRIPTION OF METHOD The Specimen Screen A simple design for a specimen screen containing an opening easy to identify and locate in the electron microscope is one with two lines of openings at right angles in the form of a cross. Such a screen is shown in Fig I. The opening at the center of the cross is identified easily and can be located quickly in the light microscope and in the objective image of the electron microscope. The specially designed specimen screens for this work were produced in quantity by electroforming. On both sides of a polished strip of copper 1 X 3 X 1/8 in., twenty patterns of the cross of openings were punched with a diamond point micro-hardness tester, using a load of magnitude

Jan 1, 1948

By Charles Morgan

An increased demand for brown iron ore in the Birmingham district during the past 18 months has caused renewed activity both in prospecting and mining these ores. In recent years the production in Alabama has ranged from 41,559 tons in 1932 to 639,351 tons in 1928. During the last 9 years about 83 per cent of the total brown ore produced in the United States has come from Alabama (Tables 1 and 2). Prospecting Two methods of prospecting are used in this district: (1) test pits, (2) churn-drilling. Usually there is certain quite definite information on an area to be prospected; some of the indications are float ore such as small gravel or small and large boulders known as "dornicks" scattered over the surface, and ore exposed by erosion in gulleys and ravines, which have cut or eroded through the overburden. Often these natural erosions furnish an indication of the thickness of the ore and to some extent of the area of the ore body. Deposits of brown ore are very irregular both in thickness and extent. Deposits are often lens-shaped or long narrow leads, some of which may be parallel and separated from one another by sand, clay or gravel. The bottom—the footwall—is also very irregular. This footwall is usually lime clay—disintegrated limestone, locally called "white horse," which usually is found at a depth of 6 in. to 20 ft. overlying the limestone. At some places sand and gravel is found under the ore instead of clay. No ore is found under the lime clay, although often the ore has sunk or slumped and is found in the upper portion of this clay, as at some of the Sloss workings at Russellville. The origin of these ores has been discussed by Major E. C. Eckel and Dr. E. F. Burchard in U. S. Geological Survey Bulletin 400, and recently the latter has done further work on ores in the Russellville district, of which reports undoubtedly will be published.

Jan 1, 1940

By Frederick M. Becket

DoctoR Albert Sauveur, distinguished scientist and Honorary Member of this Institute, predicted in the first Howe Memorial Lecture that the privilege of delivering' this annual address would be considered a highly significant honor. The intervening years have well borne out Sauveur's prophecy. I wish to assure the American Institute of Mining and Metallurgical Engineers that I also deeply appreciate this honor, recognizing at the same time the present and even more the future responsibilities with which it is accompanicd. Several of the previous lecturers had the good fortune to attend the classes of Professor Howc and to work in his laboratories. I was similarly favored, although in my instance and to my great regret the period was all too short. However, Howe's book, published in 1903, "Iron, Steel and Other Alloys," afforded me abundant opportunity to continue these studies. How well I remember the inspiration I derived from this famous book by Howe, the metallurgical master, pioneer, and educator! Remembering that Professor Howe contributed numerous papers to The Metallographist, a magazine supported from a technical point of view by the world's pioneers in metallography, I was curious a few days ago to learn the nature of Howe's early contributions to this magazine. The first paper by Howe in the first year of The Metallographist (1898) dealt with the allotropic theory; the second also treated of allotropy, and I quote the first sentence of that paper: The allotropic theory of the hardening of steel may, like so many other important theories, have to be accepted or rejected not on direct proof or disproof, but on the accumulation of circumstantial evidence for or against it. Howe's ability to stimulate others by his deep understanding and clarity of expression was truly remarkable; but just as striking was his intuitive judgment concerning the implications of metallurgical data in the arts and scienees. It therefore seems fitting that this lecture comprise a broad treatment of the subject chosen, rather than a closely documented thesis on any one phase of the problem; that in it attention be focused

Jan 1, 1938

By James Aston

Three years ago the writer presented a paper on the trend of development in the wrought iron industry,' wherein was described a process in the development of which he has been a factor, which at that time had passed through several years of progressive experimental development but which had not then been put upon a commercial scale of operation. The present paper deals with two years of observation and experience in the commercial operation of a plant by the A. M. Byers Co. at Warren, Ohio. It will not enter into the controversial field of the relative merit of wrought iron and steel in various classes of service, nor will it elaborate upon the characteristic services or fields of utility to which wrought iron is particularly adapted. It is sufficient to state that the wrought iron industry is upon a substantial basis and that the material finds service in pipe, where its advantages are in superior corrosion, fatigue, welding and threading qualities; in bar iron for staybolts, engine bolts, and rivets, demanding maximum service against corrosion and fatigue; in plates for corrosion service; and in chains, because of welding and shock-resisting characteristics. In short, ability to withstand the stresses of shock and vibration, or the ravages of corrosion, to hold protective coatings, and to give maximum efficiency in welding, are its features of relative superiority. If these features were not well recognized, the wrought iron industry would have shrunk to insignificance in the face of high costs and acknowledged limitations in manufacture. To charge that this industry is built upon a structure of assumption, psychology, and improperly weighed evidence is an impeachment of the integrity or belittling of the powers of observation of users through many centuries of service experiences. In a history which extends to prehistoric time, and which is linked up with the earliest records of ferrous products, the dominant method of manufacture, as we have known it for little over a century, occupies a very small niche in the span of years that mark production and use of wrought iron. Puddling, the outstanding manufacturing method of

Jan 1, 1929

By Chester A. Fulton

In Polk County, Florida, the mining of raw phosphates began some 50 years ago with dredging operations on the Peace River, and in other near-by places by removal of shallow overburden with negroes and wheelbarrows, or with mules and scrapers, and the excavation and screening of deposits found close to the surface. There were many individual operations of comparatively short life. Later steam shovels removed the overburden, and still later hydraulic methods were substituted for the steam shovel. Within the last 10 years large electrically operated draglines have almost entirely replaced hydraulic mining for overburden removal. The matrix is still mined by hydraulic giants and pumped to the washer or recovery plant. The many small operations have long since disappeared and the most desirable phosphate lands have gradually been acquired through purchase or merger by the seven companies that are operating in the field today. These companies are producing and selling about 2,000,000 long tons of phosphate per annum, or about two-thirds of what the industry likes to think is the normal output, with 1929 and 1930 in mind. To produce these 2,000,000 long tons of raw phosphate, they mine and treat about 1,000,000 tons of tailings from older and less efficient operations, about 11,000,000 tons of matrix, and remove from above this matrix some 22,000,000 tons of overburden. The mining practice that has made possible the excavation and handling of 34 million tons of material to win but 2 million tons of merchantable product, selling for probably an average of only $4 per long ton when dried, should be of interest to the mining profession, though little has been written of it. The Florida Pebble Field, as it has come to be known, comprises an area (Fig. 1) within a radius of about 18 to 20 miles centering around Mulberry in Polk County, a small town 30 miles east of Tampa, Florida's largest port on the Gulf coast. The geology1 of these phosphate pebble deposits may be described briefly. A fairly pure limestone was altered to a secondary apatite.

Jan 1, 1938

By James C. Ray

The age classification of the mineralized veins of the Butte district, as given by Weed and Sales, was tacitly accepted for many years. Weed, whose field work was completed in 1906, divided the copper veins into groups of four ages.' In 1913, Sales modified Weed's classification and assigned all mineralized veins (including the silver-zinc veins of the border or "peripheral" zones) to three periods of fracturing and mineralization. Both writers based their classifications mainly on the relative ages of the observable faulting whereby the veins of a so-called "earlier" system are intersected and offset by those of a "later" system. Nevertheless they possess structural and mineralogical characteristics in common which indicate that they are of the same age. The writer has maintained since 19143 that these vein systems were formed during one general period of mineralization along a network of intersecting fractures of approximately simultaneous origin and that the existing offsets are largely due to postmineral faulting. Leith,* takes cognizance of the accumulating mass of data relative to the simultaneous formation of intersecting fracture systems and says, referring to ~utte: "It now appears that the mineralization accompanying them (individual structure systems into which the veins have been grouped) is substantially of one period, indicating that the successive structural movements took place mainly within the period of mineralization." This paper presents the results of certain structural experiments which suggest a modified interpretation of the published data on the Butte district. The interpretation is substantiated by the writer's observations in the Butte mines and is offered with the hope that it will reconcile the structural with the mineralogical conditions existing in this most interesting district; also, that it will emphasize the importance of a

Jan 1, 1931

By L. A. Mekler

The recirculating furnace is primarily a heating apparatus of the convection type in which the heat-absorbing surfaces are heated by a mixture of fresh products of combustion and a portion of the combustion gases that have already given off a part of their heat in their previous passage over the heat-absorbing surfaces. In its basic conception, the recirculating furnace can be considered as a closed thermal system in which the heat-absorbing surfaces are constantly swept by a fixed quantity of products of combustion at a given initial temperature with the gases being constantly returned to the furnace and reheated before they again enter the heating zone. Gases equal in amount to those produced by the fuel burned to reheat the circulating gases are constantly ejected from the system to the stack. The recirculating furnace is the most suitable apparatus for heating by convection where low furnace temperatures must be maintained and where only a small portion of the available heat is taken out of the gases, particularly where the maximum allowable furnace temperature is low and where the final temperature of the gases is only a few hundred degrees below their initial temperature. In such cases, recirculation not only provides a method of reducing the rather high combustion temperatures of the fuel when burned without a large amount of excess air, but, by returning to the furnace the heat content of the gases at their final temperature, recovers a large portion of heat that otherwise would have been lost through the stack. The convection-type oil still is particularly suitable for the application of flue-gas recirculation. In an oil still, the heating of the oil is accomplished by applying to the tube surfaces a given quantity of heat of a certain predetermined quality, usually with the initial temperature of the gases not over 1500" F. as measured by thermocouples placed above the tube bank. To obtain the full benefit of the heating surface of the coil, the final temperature of the gases, after passing over the coil, is kept 200" to 300" higher than the temperature of the incoming oil. This final temperature varies from 500" F. for a topping still with only a slight or no

Jan 1, 1928

By G. H. Gilman

The campaign now being waged to improve the quality of the rock-drill bit is the natural outcome of the scientific development of the drilling machine during the past twenty years. In this development there has been a great increase of power output per unit of weight of machine. But the development of the rock drilling engine has been seriously hampered by the need of a drill bit that would withstand, without undue wear or breakage, the heavy rapid blows of the improved pneumatic hammer. This problem was difficult to solve because an increase in the weight or section of the drill-steel bar resulted in decreased cutting speed and higher operating costs of both the bit and its actuating engine. The solution, therefore, is to make the bit of steel that, for a given weight or section, will be more shock and wear resisting. In the attempt to meet these requirements, many of the drill-steel manufacturers alloyed the steel with vanadium, chromium, nickel, etc. on the assumption that such elements would improve the rock-drill bit but due to the sensitiveness of such steel to forging and heat treatment, higher cost, and lack of continuity of effort on the part of the steel manufacturer to perfect this product, but little progress has been made in the adoption of these steels and the so-called straight carbon steel is today recognized as the standard material for all rock-drill bits. The first step in improving drill-bit efficiency is the determination of the cause of breakage and wear. For this reason, in 1917, certain rock-drill manufacturers, in conjunction with some of the larger mining interests, conducted exhaustive tests in both the field and the laboratory. It was then found that, in the main, the cause of drill-steel troubles is not attributable to the duty imposed upon it by the normal operation of the drilling engine, but to improper forging and heat treating of the bit and to the subjecting of the bit to improper use. The fact that it is possible to minimize the troubles attributable to improper heat treatment of the drill steel has been demonstrated and it is recommended that such knowledge be made available by teaching those interested in the production, use, and up-keep of drill bits the principles on which success in this direction may be achieved. Unfortunately, but little attention has been given to the education of the drill smith. But a few years ago, the instructions given the man

Jan 1, 1922

By Paul Sterling

The general impression regarding the preparation of merchantable anthracite is that it is confined to a colossal, grimy structure, called a " coal-breaker." This name is a misnomer; for the desired result is not to break the coal, but to prevent its being broken. Preparation may be said to begin at the face of the chamber, with the mining and loading of the coal. Local conditions vary, not only ill the same field or basin, but also in the same mine, so that there is no fixed empirical rule governing the method of blasting or cutting coal. Tests should be made, when possible, to determine the explosive, or the mechanical coal-cutter, which will produce the largest percentage of what are locally known as " lump " and " prepared sizes " of anthracite. The prepared sizes are those mostly consumed for clomestic purposes. All other sizes might be called by-products of the anthracite industry; for they are not especially desirable, being the degradation resulting from the mining and handling of a brittle or laminated material. Being low in volatile combustible matter, anthracite burns most successfully when nearly of a uniform size, permitting the easy passage of air through the voids. This accounts for the large number of sizes into which the coal is separated. Table I. gives the various sizes, the diameter of ring over and through which each size is made, and the usual purpose for which it is employed.

Jan 1, 1912