Search Documents

By Erik M. Westerberg

The Soilex Pile combines a slender shaft, for quick and easy installation, with an enlarged pile toe, for high capacity. The key component is the Expander Body, which is inflated by injecting cement grout when in position. The latest development in the Soilex Pile System results in a reduction of the total cost of Soilex Piles, in many cases values that are competitive with pre­cast concrete piles and displacement piles. Soilex Piles can now be installed on top of a bearing soil layer, instead of 3 to 4 m into that soil as previously required, further minimising the ground disturbance. Soilex Piles achieve high capacity in relatively loose soils, with ultimate loads typically between 1000 and 2000 kN in a sand with CPT qc = 5 to 10 MPa or SPT N= 10 to 20. It is possible to pre-load and proof-load all piles with dynamic testing up to 2000 kN or using built-in jacks, thereby verifying the capacity. The vibratory installation method, which is extremely quick and causes very little soil disturbance and noise, is exemplified by two case histories.

Jan 1, 2000

By A. K. Singh, R. Singh, P. K. Mandal

On the basis of in situ study of pillar loading at different sites, an attempt is made in this paper to visualize the development of mining induced stress under varying geo-mining conditions. Field study demonstrated interesting interaction between size of pillar and nature of roof rock mass under the influence of increasing dimension of the excavation. Stiffness of pillars/overburden, extraction ratio and depth cover are observed to be the important parameters for the estimation of mining induced stress over the pillar. These parameters influence, both, the value of ultimate induced stress (vertical) and its range of influence ahead of the face line. Further, it is observed that the change in width/height (w/h) ratio of a pillar has got considerable influence over the nature of mining induced stress over it. Impact of highly dynamic nature of mining induced stress over the natural supports is observed to be the most serious factor for the safety of working under a hard and massive roof rock mass. On the basis of these observations, a conceptual model of interaction between the natural support and overlying strata is discussed in the paper. ZUSAMMENFASSUNG: Aufgrund ist in situ Studium von Säule Beladung an verschiedenen Stellen, ein Versuch in diesem Papier gemacht, die Entwicklung des Bergbaus vostellen sich, Spannung unter Änderung von Geo Bergbau von Bedingungen hat veranlaßt. Feld Studium hat interessante Wechselwirkung zwischen Größe von Säule und Natur von Dach Felsen Masse unter dem Einfluß von Vermehrung Dimension des excavation vorgeführt. Steifheit des Säulen Overburden, Herausziehung Verhältnisses und Tiefe sind beobachtet bedeckt, die wichtigen Parameter für die Schätzung des Bergbaus zu sein, Spannung über der Säule hat veranlaßt. Diese Parameter beeinflussen, beide, der Wert allerletzter veranlaßter Spannung (senkrecht) und sein Bereich des Einflusses voraus von der Gesicht Linie. Weiter ist, es beobachtet, daß die Änderung in Breite Höhe (W H) Verhältnis einer Säule beträchtlichen Einfluß über der Natur des Bergbaus erhalten hat, Spannung hat darüber veranlaßt. Schlag sehr dynamischer Natur des Bergbaus ist Spannung über den natürlichen Stützen beobachtet hat veranlaßt, der ernsteste Faktor für die Sicherheit des Arbeitens unter einer harten und massiven Dach Felsen Masse zu sein. Aufgrund dieser Beobachtungen, ein begriffliches Modell der Wechselwirkung zwischen der natürlichen Stütze und der überlagernde strata ist im Papier diskutiert. RESUME: En se basant sur dans l'étude de situ de chargement de pilier aux sites différents, une tentative est faite dans ce papier pour envisager le développement de creuse la tension persuadée sous varier de conditions de geo creuse. L'étude de champs a démontré l'interaction intéressante entre la taille de pilier et la nature de masse de rocher de toit sous l'influence d'augmenter de dimension de l'excavation. La raideur de piliers overburden, la proportion d'extraction et la couverture de profondeur est observée pour être les paramètres importants pour le jugement de creuse la tension persuadée par-dessus le pilier. Ces paramètres influencent, les deux, la valeur de tension persuadée ultime (vertical) et sa gamme d'influence en avant de la ligne de face. Plus, il est observé que le changement dans la largeur hauteur (le w h) la proportion d'un pilier a reçu l'influence considérable par-dessus la nature de creuse la tension persuadée par-dessus il. L'impact de nature extrêmement dynamique de creuse la tension persuadée par-dessus les soutiens naturels est observé pour être le facteur le plus sérieux pour la sûreté de fonctionnement sous une masse de rocher de toit dure et massive. En se basant sur ces observations, un modèle conceptuel d'interaction entre le soutien naturel et les couches recouvrant est discuté dans le papier.

Jan 1, 2003

By 12670

The Cigar Lake project will develop the world’s second largest high-grade uranium deposit. The Cigar Lake Phase 1 orebody contains approximately 226 million pounds U3O8 at an average grade of 20.7% U3O8. The mine, to be operated by Cameco Corporation, will use a unique water jet boring mining method to cut previously frozen ore. A distinctive ore handling design is required to handle the highgrade ore slurry exiting the mining machines. The ore will be crushed and ground underground, with the ore slurry then pumped to surface. Loaded into purpose-designed containers on tractor-trailer units, the ore slurry will be trucked to Cogema Resources Incorporated’s McClean Lake mill. McClean Lake will leach all of the ore. Forty-three percent of the resulting uranium solution will remain at McClean Lake for processing into yellowcake. The other 57% of the uranium solution will be shipped to Cameco’s Rabbit Lake mill for processing into yellowcake there. Detailed design for the Cigar Lake project is now underway. Barring regulatory or market delays, production could start up as soon as early 2006.

Jan 1, 2004

By · J. B. Boisvert, O. Leuangthong, T. Acorn

Optimizing final pit limits for stochastic models provides access to geologic and economic uncertainty in the pit optimization stages of a mining project. This paper presents an approach for optimizing final pit limits for a highly variable and geologically complex gold deposit. A heuristic pit optimizer is used to manage the effect of geological uncertainty in the resources within a pit shell with multiple uncertainty rated solutions. The uncertainty rated pit shells follow the meanvariance criterion to approximate the efficient frontier for final pit limits. Stochastic dominance rules are then used in a risk management framework to further eliminate sub-optimal solutions along the efficient frontier. This results in a smaller set of final pit shells that could be further analyzed for production scheduling. Additionally, the original solutions are analyzed for changes in the mining limits and two regions are targeted as potential regions for further exploration.

By · J. B. Boisvert, O. Leuangthong, T. Acorn

Optimizing final pit limits for stochastic models provides access to geologic and economic uncertainty in the pit optimization stages of a mining project. This paper presents an approach for optimizing final pit limits for a highly variable and geologically complex gold deposit. A heuristic pit optimizer is used to manage the effect of geological uncertainty in the resources within a pit shell with multiple uncertainty rated solutions. The uncertainty rated pit shells follow the meanvariance criterion to approximate the efficient frontier for final pit limits. Stochastic dominance rules are then used in a risk management framework to further eliminate sub-optimal solutions along the efficient frontier. This results in a smaller set of final pit shells that could be further analyzed for production scheduling. Additionally, the original solutions are analyzed for changes in the mining limits and two regions are targeted as potential regions for further exploration.

By K J. F Logan, P W. Leaman, B A. Tucker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Nam San copper-gold deposit was discovered in 2011 and is a likely blind extension of the Permian age Phu Kham structurally deformed porphyry/skarn copper-gold deposit.The Nam San mineralisation is hosted within a dominantly sericite altered schist unit located to the north of the current Phu Kham open pit operation and is overthrust by an allochthonous barren cover sequence of limestone, granite and sandstone. Reinterpretation of the Phu Kham geology developed the concept of a possible telescoped porphyry copper-gold system at depth. Initial drilling intersected remobilised copper mineralisation in a basal conglomerate, confirming the concept. A reconnaissance vector array induced polarisation (IP) survey identified a deep chargeability anomaly from which a drilling target was developed from 3D inversion modelling of a detailed follow up dipole-pole-dipole anomaly. Drilling of the chargeability anomaly intersected the blind Nam San copper-gold mineralisation beneath the thrusted cover sequence.The key discovery parameters are the result of an integrated exploration program that included reinterpretation of the local stratigraphy, which developed the concept of a deep blind orebody, IP surveys capable of penetrating through the barren cover and a commitment to a deep directional drilling program to test these concepts and targets. The inferred resource remains open at depth, and further assessment will most likely be through underground development.CITATION:Leaman, P W, Tucker, B A and Logan, K J F, 2015. The discovery of the Nam San copper-gold deposit, Phu Kham, Laos, in Proceedings PACRIM 2015 Congress, pp 515–520 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By A. Eslami

In recent development of piled raft design, the contribution of both raft and piles to tolerate the loads is taken into account, depending on the stiffness and contributions of involved elements i.e.; piles, raft and surrounding soil. The piles are usually required not to ensure the overall stability of the foundation but to act as settlement reducers. One alternative method of foundation design is therefore to introduce piles purely as a means of improving or enhancing the stiffness of the base soil by structurally disconnecting the piles from the raft. In this paper, two and three dimensional finite element analysis of disconnected pile-raft systems are performed on three case studies including a 12-storey residential building in Iran, a 39-storey twin tower in Indonesia, and the 256m height of Messeturm tower in Frankfurt, Germany. The analysis include different geometrical parameters, e.g., pile spacing and embedment length, arrangement and raft thickness for foundation system to obtain the optimized design functions and to clarify the role of each parameter and method of analysis. The parametric study results and comparison to a few field measurements indicate that by concentrating the piles in the central area of the raft foundation leads to the optimum design with the minimum total length of piles. This achievement can be considered as a criterion for project cost efficiency. On the other hand, disconnected piled-raft systems can significantly reduce the settlements and raft internal bending moments. Finally, the comparison indicates that simple and faster 2D analysis has almost the identical results to 3D analysis which is complicated and time consuming.

Jan 1, 2008

By Samer Sadek, Brian Hagan

We are thrilled to welcome you to the 2025 Rapid Excavation and Tunneling Conference (RETC), which will be held in Dallas, TX. This year’s conference will showcase the continued trend of strong industry interest, as there will be a record setting 115 papers being presented over the course of three days. The set of papers compiled in this book captures the latest and greatest information on a broad array of topics within our fascinating tunneling industry. We hope that the compilation of selected papers in this book will provide a comprehensive recap of the conference while also providing a source of future reference for contractors, engineers, and anyone in general who is a student of our beloved and unique industry. Since its inception in 1972, RETC has been the preeminent tunneling forum to promote ideas, tell stories, share lessons learned, and promote new technologies. RETC prides itself on its focus towards highlighting real-world experiences and practical ideas, with the intent to help the entire industry learn from one another and grow. The need for us all to stay sharp and remain on the cutting edge of technology has never been stronger – the technology and ideas that have been applied in aerospace are now attempting to mix with tunneling, and the advancement of AI continues to permeate all industries. However, no amount of technology or AI can fully replace the human element, and in our tunneling industry, the human element is key and is what sets us apart. In tunneling, every project is different, because the ground is always different. We can only take what the ground will give us, and we must rely on our past experiences to get through present day challenges. Most importantly, we must rely on each other. This is the heart of what RETC is all about. For those of you attending this conference, we encourage you to attend as many sessions as possible and engage with your colleagues to discuss during the breaks in between sessions. This sharing of ideas is what keeps us connected and helps to expand our industry. Please also try to engage with the scholarship students and the newcomers who will be in attendance, as it is the new ideas and fresh energy from the next generation that will continue to make our industry thrive into the future. The program chairs thank and greatly appreciate the efforts made by our session chairs, co-chairs, authors, the members of the RETC Executive Committee, and most importantly the SME staff towards making this RETC possible.

Oct 1, 2025

By S. McGinn

The Brunswick Mine Diesel Particulate Filter Study was one of several research projects initiated by the Diesel Emissions Evaluation Program (DEEP). The study was carried out at Noranda?s Brunswick Mine in Bathurst, New Brunswick by Noranda Technology Centre and Brunswick Mine personnel with the collaboration of Natural Resources Canada - Canada Centre for Minerals and Energy Technology (CANMET), National Institute of Occupational Safety and Health (NIOSH), Andreas Mayer of VERT, and diesel particulate filter (DPF) system suppliers. The study began in early 2000. Field evaluations continued for 20 months. The final report?authored by Sean McGinn?was submitted to DEEP in the Autumn of 2003.

Jan 1, 2004

By C. G. Dunn, P. K. Koh

The primary recrystallization textures of 11 single crystals cold rolled 70 pct were determined. The effect of crystal orientation on recrystallization behavior was investigated also and found to be large. An exception was found to the relationship that strong components of the recrystolliza-tion texture are rotated from the cold rolled texture by 30° about <110> axes, but generally this relationship was found to hold quite well. Evidence supporting oriented nucleotion was found and discussed in terms of probable active slip systems and <110> edge dislocations. THE present paper is one of a series&apos;.&apos; on recrys-tallization phenomena in cold rolled 31/4 Si-Fe single crystals and is mainly concerned with the textures produced on recrystallizing from stable end orientations. Data for the cold rolled textures of the crystals used have been reported by Koh and Dunn." Their results showed that the sharpness of the cold rolled textures varied throughout the range of stable end orientations and that the tendency to re-crystallize was related to the sharpness of the cold rolled texture, wherein the rate of recrystallization increased and the size of recrystallization grains decreased with decreasing sharpness of the cold rolled texture. In the project under consideration the cold rolled crystals involved a range of initial orientations that, together with those studied earlier,&apos; provide information on several points. The first point is whether the recrystallization texture from a (111) [112] cold rolled texture, a stable end orientation that can be approached from different directions, correlates in any way with the initial orientation before cold rolling, or whether the recrystallization texture is entirely determined by the observable features of the cold rolled texture. The second point involves a preliminary study to see if the main components of the recrystallization textures correlate with the most probable active slip systems. The third point is to determine what effect departure from slip on one slip system has on the tendency to recrystallize. Experimental Procedure Nine specimens from a previous investigation and two additional ones from thicker stock (lot D) but of similar composition to the others were used in the present work. The latter two crystals, like the nine, were cold rolled to a reduction in thickness of 70 pct and the amount of widening was determined. Depending on their primary recrystallization behavior, the cold rolled crystals were given short or long anneals at temperatures of 980°C or higher. Table I summarizes the data on initial orientations, the textures obtained by cold rolling, and the anneals given to provide samples for the present work. Fine grained specimens were thinned to 0.002 in. thickness and placed in an integrating specimen holder. Chart recordings using a transmission X-ray method and MoKa radiation were obtained for diffraction from (110) planes. This method,&apos;,3 which gives data for all of the pole figure except a central region of 30" radius, proved sufficient to give generally five, and sometimes six, of the six possible pole concentration areas of any one component of the texture. These data, therefore, were generally adequate for a positive identification of each component present. The first texture obtained for specimen B-2 was poorly defined because of too coarse a grain structure and therefore too few crystals in each component for satisfactory X-ray reflections. The same

Jan 1, 1957

By Don Phelps, John Hawley, David P. Field

In recent years observational techniques of tunneling have become increasingly popular methods to facilitate complex underground infrastructure projects. The traditional design and construction management practices developed in Europe have been adapted for application in North America to suit a more restrictive management and legal culture. This paper will discuss three recent projects, the San Diego Mission Valley East Extension, Washington Dulles International Airport People Mover, and the Seattle Beacon Hill Station and Tunnels, with the objective of identifying the challenges of applying observational tunneling methods to established contractual practices in North America.

Jan 1, 2005

By Antonio Pineda, Roger K. McLimans, Felicity E. Lloyd

lmenite is a primary ore feed to the DuPont chloride process for the manufacture of titanium diox-ide pigment. We seek to determine ilmenite geochemistry as a function of original source and as-certain which ilmenites have chemistry most amenable to upgrading via iron-leaching (leucoxenization) and that have favorable, with respect to pigment manufacture, trace element content. Ilmenite geochemistry is a function of its primary origin and of subsequent alteration. Heavy mineral sand deposits may contain ilmenite from one or several dominant source rock(s). In addition, ilmenite may alter in the weathering environment, changing the major element compo-sition (iron-leaching) and certain of the minor element content. A primary objective is to classify ilmenites in relation to origin in order to fingerprint source rocks in provenance determination. The changes in trace element chemistry during alteration are also investigated. A “decision tree” is developed to classify ilmenite types and source rock origins. Ultimately, with those methods and by amassing a database of ilmenite types from worldwide locations, it should prove possible to determine ilmenites (and their sources) more susceptible to iron leaching in the weathering en-vironment. Such ilmenites, enhanced in their titanium content, are the preferred ore targets. The method used is electron microprobe analyses at elevated conditions of voltage, cur-rent, and counting time to enable higher precision. In-situ ilmenites from igneous, metamorphic, and altered rocks (saprolites) are analyzed. Initial foci for sedimentary ilmenites are restricted provenance (approaching monogenetic, examples from Spain, Portugal) and polygenetic prove-nance (Denmark). Altered ilmenites, including the DuPont Florida ore, are used to characterize the chemistry of leucoxenization. Trace element concentration, detectability, and cost considera-tion, led to focus on Mn, Mg, V, Cr, and Nb to develop a classification scheme validated by dis-criminant analysis and “classification-regression trees”. Results show a high degree of success for restricted provenance study and an acceptable one for polygenetic provenance.

Jan 1, 2005

The Government signalled its intention in the Economic Statement on 17 December 1987 to improve the fairness of the taxation system and to facilitate the process of economic adjustment by: removing tax concessions that benefit some taxpayers at the expense of other taxpayers,ensuring that those who can afford it shoulder their fair share of the tax burden,securing a revenue base which will provide sufficient resources to maintain effective social services,reducing artificial protection and concessions that discriminate against some sectors, and&nbsp;encouraging confidence through an economic environment with a medium-term orientation. The Government has clearly stated to all sectors that tax preferences will be phased out and businesses need to look inwardly to their investment policies if they are to survive in an open economy. This paper will address the effect of these Government objectives on the taxation structure for all forms of mineral exploration in New Zealand. The present tax structure will firstly be analysed, in particular setting out the tax advantages available to the industry. The effect of changes to the tax system within the recent past which relate to mineral exploration will then be examined. Finally the paper will address the question of possible future changes, particularly in the light of Government&apos;s intention to move towards a tax system which does not provide an advantage for any one sector of the economy.

Jan 1, 1988

By J. P. Rider

The number of extended cut mining systems has increased significantly in coal mines over the last decade, and there is a constant push to extend the face ventilation systems to even greater setback distances. The need to maintain airflow at setback distances of 12.2 m (40 ft) and beyond requires that methods for delivering intake air to the face be improved, or alternative ventilation techniques be implemented. The emphasis of this research effort was to examine various techniques to improve the distribution of available air at the mining face in order to reduce face methane levels. A study was conducted comparing the performance of a jet fan, used in conjunction with a machine mounted scrubber, with blowing curtain ventilation in a 27.5 m (90 ft) heading. In addition, a second study was performed on blowing curtain systems examining how scrubber flow, intake air velocity, and curtain setback influence face methane concentrations. Results showed that when the heading advances to a depth of 27.5 m (90 ft) blowing curtain systems were more efficient at diluting face methane levels when compared to a jet fan. Also, increases in scrubber flows and curtain velocity resulted in lower face methane concentrations for blowing curtain systems at 9.2 and 15.2 m (30 and 50 ft) setbacks.

Feb 24, 1997

By Janet Torma-Krajewski

Research has shown that an ergonomics process that identifies risk factors, devises solutions to reduce musculoskeletal disorders (MSDs), and evaluates the effectiveness of the solutions can lower worker exposure to risk factors and MSDs and improve productivity. A review of the Mine Safety and Health Administration (MSHA) injury/illness database indicated that 46% of illnesses in 2004 were associated with repetitive trauma and 35% of nonfatal lost days involved material handling during 2001? 2004. Even though these statistics show that MSDs significantly contribute to occupational illnesses and injuries in the U.S. mining industry, few mining companies have implemented an ergonomics process. Despite the many unique challenges in the mining environment, three mining companies partnered with the MSD Prevention Team at the National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory to demonstrate that an ergonomics process could be systematically implemented and effectively integrated with existing safety and health programs. Because these three mining companies were very different in organization, culture, and size, the ergonomics processes had to be modified to meet the needs of each company. A description of how these three companies applied ergonomics and the tools and training used to implement their processes is given. Prior to discussing the case studies, general information on the elements of an ergonomics process is provided.

Feb 1, 2009

By Murad Y. Abu-Farsakh

This paper presents the analyses of load-transfer (t-z) behavior of twelve prestressed concrete (PSC) instrumented test piles that were driven in different locations of Louisiana. The load transfer method is an efficient and practical tool for the analysis of single driven pile to predict the ultimate load. The test piles were instrumented with vibrating wire strain gauges in order to calculate the shear transfer for different soil layers during the static load test. The static load test was performed on all the test piles after 10 to 14 days of end of driving. Empirical load-transfer models were proposed previously by different researchers (Fleming 1992, Hirayama 1990, Krasinski 2012, Bohn et al. 2017) after analyzing the instrumented test pile results. For this study, load transfer of each soil layer was measured and compared with the previously developed existing model. The stiffness parameter (M) for the hyperbolic equation was calibrated in order to best match the measurements. The good agreement of the proposed curves was then confirmed by applying them to assess the overall load-settlement curve of other pile load test results available in the literature. INTRODUCTION The load transfer mechanism (stress-strain relationship) for an axially loaded pile usually comprises of three loading mechanisms: axial deformation in the pile (z), soil skin friction along the shaft (qs), and soil end-bearing (qb). The development of soil skin friction with axial deformation is referred as the t-z curve, and the development of soil end-bearing with axial deformation is referred as the q-z curve. Figure 1 presents the load transfer mechanisms in an axially loaded pile and the corresponding spring mass models for t-z and q-z curves (API, 2002). In order to construct the load transfer curve in clay under vertical load, the axial load transfer (t-z) curve and end-bearing load transfer (q-z) for that particular soil should be assessed separately. The axial load transfer (t-z) method is probably the most widely used technique to study the problem of single axially loaded piles. Therefore, the load transfer through the shaft of the pile and are getting more and more important compared to the only the pile capacity analyses. The load transferred from shaft to the surrounding clay soil is a function of the width of the pile and the surface roughness of the pile and clay properties. The development of a representative procedure allows the assessment of the t-z curve in soil (sand and/or clay) that leads to the prediction of a nonlinear vertical load-settlement response at the pile head.

Jan 1, 2018

By F. S. Young

Previous laboratory and field experimentation has demonstrated the effect of several variables on drilling rate.1-5 These results have been incorporated into optimization theories6-" for the purpose of reducing drilling cost. Minimum-cost drilling theories rely on a combination of historical data and empirical prediction techniques for selecting optimum bit weight and rotary speed. Past solutions have required extensive use of computing equipment because of both the complexity of the mathematical formulations and the large number of parameters involved. Field attempts to apply these computed results have frequently failed because of the uncertainty of input data requirements. Humble has developed an on-site computer system to control bit weight and rotary speed and thereby implement the concepts of minimum-cost drilling. This system can (1) perform short interval drilling rate tests for formation evaluation, (2) use the results of these tests as input information to solve minimum-cost drilling formulas, and (3) control bit weight and rotary speed in accordance with these computed solutions. The purpose of this paper is to describe the computer control system and present results of initial field testing. Theoretical Considerations Minimum-cost drilling (MCD) requires a quantitative evaluation of the variables involved. Several forms of a basic mathematical model have been sug-gested.&apos;?,&apos; "he relationships reported here form the basis for the solution programmed in this work. Four equations are used, expressing drilling rate, bit bearing wear, bit tooth wear, and cost. A solution for minimum-cost drilling assuming constant bit weight and rotary speed over the entire bit life has been programmed for use in computing MCD schedules. This solution is subject to certain limiting assumptions such as those discussed by Graham et a1.I2: 1. Drilling cost is the summation of bit cost, rotating cost, connection cost and hoisting cost. 2. Diamond bits are excluded. 3. Bit life is limited by either bearing failure or tooth wear, or by a combination of operational factors that make it cheaper to pull an incompletely consumed bit. 4. Circulating hydraulics are adequate and do not limit drilling rate. 5. Bit weight considerations exclude hole deviation. 6. Drilling rate is a function of only bit weight, rotary speed, and degree of tooth dullness; that is, the effects of pressure, lithology, fluid properties hydraulics and drill string dynamics are ignored. In equation form, the four MCD expressions are as follows:

Jan 1, 1970

By Adams F. C, Ridley K. L

Economic conditions after WorId War II made the recovery of Australian sources of sulphur one of considerable national importance. From 1947 to 1949 an investigation was made of recirculation techniques to produce acid plant grade gas from the Dwight-Lloyd down-draught sintering plant.During 1949 it appeared feasible to produce a gas of suitable 802 concentration and a decision was made to construct a gas purification train and a 150 tons/day contact acid plant. However, a number of difficulties remained in the production of the gases for sulphuric acid manufacture and as a result of research conducted to overcome these troubles the continuous up-draught sintering process was developed.The principal difficulties were:(a:) The down-draught sintering practice, as developed, produced an unusually high metallic lead precipitation in the windboxes. The disposal of this lead interrupted sintering operations and the delivery of gas to the acid plant.(b) The production capacity of the existing sintering plant was fully extended and the adoption of recirculation of gases, in an endeavour to satisfy acid plant requirements, would probably reduce the plant production capacity.(c) The prevailing high temperature of water available for purification train cooling required a higher than...

Jan 1, 1956

By J. B. Zadra

The use of activated carbon for extracting gold and silver from pregnant cyanide solution and pulp has been investigated many times. The primary advantage of this use of activated carbon is that .the dissolved values can be recovered from slimy ore pulps or from slime portions of ore without settling and thickening or filtering. The loaded carbon is removed from the barren pulp, and the pulp can then be discarded. Activated carbon has been used recently in treating gold ores containing very little soluble silver. When the carbon was loaded with a suitable amount of gold, the silver load was negligible. The remaining problems concerned the removal of the gold from the carbon, the recovery of the gold as bullion, and the reuse of the unloaded carbon. As described in a recent report, a method that solved these problems was developed. The gold-laden carbon was leached with caustic sodium sulfide solution and the gold simultaneously recovered by electrolysis. Both the carbon and the spent solution can be reused. That process was applicable to gold-laden carbon only. It was not applicable to carbon carrying silver, because sodium sulfide does not leach silver from carbon but "fixes" it. It has been necessary, therefore, to develop a modified process for the removal or desorption of both gold and silver from loaded carbon. This modi¬fied process permits the use of activated carbon for extracting both gold and silver from gold ores carrying enough silver to have economical interest or in which silver may be the predominating value.

Jan 1, 1952

By M. G. Corson

THE iron-silicon alloy series has always been one of the most puzzling among the binary alloys. Examining the well known mechanical properties of the iron-rich alloys only we meet the following situation: The ultimate strength and yield point of alloys worked and annealed under the usual conditions represent nearly a straight line function of the silicon content up to 4.5 per cent. silicon (Fig. 1). Starting at the ultimate strength of 35,000 lb. and at a yield-point of 16,000 lb. for pure electrolytic iron, one reaches a -maximum strength of 93,000 lb. and a maximum yield point of 74,000 lb. at 4.5 per cent. silicon. This corresponds to an increase in ultimate strength by 13,000 lb. per each per cent. of silicon added and nearly the same rate applies to the yield point. The data mentioned are taken from the investigation by T. D. Yensen,1 and while they do not exactly corroborate the results obtained by earlier investigators, they seem to be the most correct. Plastic properties of the alloys are controlled by a much more complicated relationship. Up to 2.5 per cent. Si, the elongation stays close to 50 per cent. (in 2 in.) and the area reduction amounts to 85 per cent., a situation that forms the usual feature of all alloys representing strictly solid solutions. The plasticity of the latter is always nearly equal to that of their base metal. Beyond 2.5 per cent. silicon, the situation becomes much more complicated Yensen observed an enormous drop in elongation and area reduction at about 2.65 per. cent. silicon, where the first hardly reaches 10 per cent. and the second is still lower; he found, however, a considerable recovery in plasticity at about 2.8 per cent. Si and up to. 4.5 per cent. Si it is represented by 20 per cent. for the elongation and 30 per cent. for area reduction.

Jan 1, 1928