Search Documents

Komatsu America has introduced its 2-MW (2,700-hp), 930E-3 ac electric drive truck with a 290-t(320-st) capacity. The truck is designed to provide increased productivity, lower cost per ton hauled and improved speed and control. The 930E-3 is powered by a Komatsu SSDA16Vl6016-cylinder engine. It is capable of speeds up to 65 km/h(40 mph) and is a 15-percent to 20-percent more productive unit than 218-t (240-st) trucks, at a lower operating cost per ton. The 930E-3 also provides enough torque and speed to get up and off ramps easier than mechanically driven trucks. And it can climb at altitudes up to 3,650 m(12,000 ft) without any fuel deration.

Jan 1, 2004

By Pietro Navarra

Cooling of critical furnace equipment to produce freeze lining is of particular interest as many metallurgical processes are intensified while attempting to prolong campaign life. This idea was combined with high-capacity heat pipes in the design of a copper slag launder. The design methodology of the launder and heat pipe cooling system is examined in this paper. With reliable material properties and operating conditions, CFD was used to quantitatively predict the skull thickness and the corresponding heat load applied to the slag launder. The operational limitations of heat pipe technology were considered and an appropriate cooling system was incorporated into the model. Parametric modeling was used to simulate several launder and heat pipe configurations. The generated results were then used to optimize the design of the launder, which was built and tested in August of 2005. The experimental performance of the cooling system is evaluated and compared with the model results.

Jan 1, 2006

By Andrew Malinak, William Perkins

Seattle’s Elliott Bay Seawall protects the 1½ miles of downtown waterfront between South Washington and Broad streets. The seawall supports the urban waterfront and infrastructure, including the Alaskan Way Viaduct and Alaskan Way, access to historic waterfront piers, and numerous essential buried utilities. Most of the original seawall was constructed between 1916 and 1936 over soft/loose non-engineered fill, estuary, and beach deposits. The majority of the original seawall was a pile-supported timber relieving platform that extended up to 60 feet behind the face of the wall (Figure 1). With maximum spacing between the timber piles of 3 to 5 feet, a virtual forest of timber piles were driven for the original wall.

Jan 1, 2018

By John R. Bartels

Remote operation of continuous mining machines has enhanced the health and safety of underground miners in many respects; however, numerous fatal and non-fatal continuous miner struck-by accidents have occurred. In an effort to prevent these injuries, NIOSH researchers at Pittsburgh Research Laboratory studied the workplace relationships between continuous miner operators and various tramming tasks of the equipment using motion capture data, operator response times, and field of view data to evaluate the factors influencing operator-machine struck-by events (contact with a solid object) in a virtual mine environment. It is not feasible (nor ethical) to use human subjects to directly evaluate factors that precipitate such injuries. However, use of motion analysis data and digital human models can facilitate analysis of struck-by accident risk by allowing investigators to manipulate factors that influence injury. Factors included in this study included machine speed, direction of escape, the direction the operator was facing relative to the machine, work posture, distance from machine, and operator anthropometry. Close proximity to the machine, high machine tramming speeds, a right-facing orientation and operator positioning near the tail all resulted in high risk of being struck.

Jan 1, 2008

Nautilus Minerals and Neptune Minerals are betting that the next great metals rush will take place more than 1,500 m (5,000 ft) below the sea. Nautilus is the first company to commercially explore the ocean floor for gold and copper seafloor massive sulfide (SMS) deposits. Its main focus is the Solwara 1 Project, a polymetallic copper, gold, zinc, silver deposit that is under 1,600 m (5,200 ft) of water off the coast of Papua New Guinea in the western Pacific Oceans? Rim of Fire. Nautilus Minerals, in a joint venture with Placer Dome (now Barrick Gold), began its exploration of what would become the Solwara 1 area in 2005 with side scan sonar and dredge sampling. The dredge and grab sampling confirmed the grade tenor of earlier sampling by scientific research programs. The 45 dredge samples aver-aged 10.8 percent copper, 3.7 percent zinc, 224 g/t (6.5 oz/st) silver and 13.7 g/t (0.4 oz/st) gold. Nautilus has since staked out more than 300,000 km2 (115,800 sq miles) of tenement licenses and exploration applications in the waters off Papua New Guinea, Fiji, New Zealand, Tonga and the Solomon Islands. That is an area about the same size of the United Kingdom. Interest in Nautilus and its projects has grown tremendously since its inception. The company is now listed on the Toronto Stock Exchange. It has raised more than $300 million and spent more than $23 million on exploration. The company has gained the backing of mining majors such as Teck Cominco, Epion, Anglo American and Barrick Gold. It is positioned to become an emerging producer in 2010. Teck Cominco recently agreed to exercise share purchase warrants to acquire three million additional common shares of Nautilus at a price of US$15 million. This will take Teck Cominco?s shareholding to approximately 7.2 percent of the issued shares. Teck Cominco will conduct and manage a ship-based exploration program that will run in addition to the exploration that was already planned for 2008.

Jan 1, 2008

By K. Pathak

Loaders and dump trucks are the most commonly used surface-mining equipment. Negligence of the safety-engineering aspects of dump trucks may result in serious accidents in a mine. A reduction in the risk of an accident due to the deployment of trucks can he achieved by engineering analysis, risks assessment, improved safety features, active safety devices, condition-based maintenance, in-built protection systems, etc. This paper presents some cases of accidents in Indian surface coal mines and advocates a systems approach to safety.

Jan 1, 1999

By Rob Morrison, Peter Cameron

"Many products and technologies have been developed from outcomes of research projects carried out by the Julius Kruttschnitt Mineral Research Centre (JKMRC). When these products and technologies are applied to the design and optimisation of blasting, comminution and separation, improvements in profitability can be realised.In 1970 Alban Lynch promoted two practical ideas to improve plant operations:• Ore and equipment properties can be separated allowing experience with one type of ore or equipment to be transferred to other types of ore and equipment. If this experience was encapsulated in a mathematical model, then these properties could be combined and used to simulate (ie. to design and to optimise) complete mineral processing circuits.• Many problems associated with scale-up from laboratory to industrial equipment could be eliminated by experimental work on full-scale equipment in the plant.Many JKMRC research projects have focussed on the development of models of unit operations in mineral processing and their application to process simulation.Models of comminution and classification developed at the JKMRC have been used since the early 1980's. Ore characterisation techniques developed to support these models are licensed world wide through JKTech. The application of comminution modelling techniques to blasting, which optimises the process feed size distribution is used in Mine-to-Mill® projects. The advances in the understanding and modelling of froth flotation over recent years have provided the opportunity for integrated ore characterisation and process optimisation from resource to product.JKMRC project outcomes often provide proven opportunities for the mineral industry to improve performance and productivity. JKTech was established in 1986 to commercialise and market the most promising outcomes and thus ensure their continuing availability to the mineral industry.They include:• Commercial software (JKSimMet, JKSimBlast and JKMetAccount).• Monographs (Comminution and Blasting).• Technologies (Mine-to-Mill® and flotation optimisation).• Hardware products (JKFrothCam, JKJetLift® and the Mineral Liberation Analyser).This paper summarises these technologies and their benefits."

Jan 1, 2003

ignitions caused by cutting tools have occurred at a rate of some 14 per year in UK coal mines since 1965, mostly on the coalface. The rate has held steady despite reducing output and number of collieries. Investigations were carried out over this period into factors affecting both the concentration of firedamp in the cutting zone and the igniting source. A study into detecting and suppressing ignitions on shearers has been undertaken and it is feasible to prevent certain ignitions from spreading outside the cutting zone. Practical measures have been adopted by British Coal to identify frictional ignition sites and to lay down working procedures to minimise risk.

Jan 1, 1988

By Kevin Phelps, Jason Baird

When dealing with high velocity projectiles, the ability for researchers to accurately and precisely measure the velocity of the projectile is of great value. This report will analyze three different methods of recording high velocity projectiles for: their ability to record velocity data, pros and cons for each method, and any possible bias or limitations that would result. Method 1 uses a Phantom V10 high-speed video camera and a velocity reference screen to record the projectile’s path and proprietary Phantom software to analyze the data and determine velocity. Method 2 utilizes two break screens. This method, consisting of strung copper wire as the break material, is one that has been used in the past by Missouri University of Science and Technology (MS&T) researchers in assisting in finding velocities of high-speed projectiles. Method 3 is a pair of make screens, similar to Method 2 in that two screens were used for each test but relies on a projectile making a circuit between two sheets of metal separated by an insulation layer, to find a velocity. All three methods will be used simultaneously in each shot to rule out any projectile differences in subsequent shots. Projectiles of three different relative velocities, low, medium, and high, will be fired and analyzed to determine strengths and weaknesses of each method.

Jan 1, 2014

By H. E. Urtubia

"BHP-Billiton’s Minera Escondida Limitada, in Chile, is one of the world’s largest copper producers. It treats a combined 10,500 tph of copper ore through its two concentrators: Los Colorados and Laguna Seca. The performance of the rougher circuit at each concentrator was measured and analysed using the JKTech flotation optimisation methodology. This involved developing a flotation model for each concentrator based on cell operating parameters (for example bubble surface area flux and froth recovery) and feed ore floatability characteristics. The rougher circuit performance was evaluated in terms of traditional measures, such as grade and recovery. The operation was also analysed using the measured cell operating parameters and ore floatability and the effect of these with regard to performance (grade / recovery) was assessed.This paper presents a comparison of the rougher circuit at each concentrator in terms of these parameters. The main differences in rougher circuit performance between the two plants were attributed to differences in feed ore floatability characteristics and froth recovery. The comparison highlighted opportunities where performance improvements could be made. The study also showed the usefulness of separating the flotation process into easily measurable subprocesses to further identify the different mechanisms occurring in each rougher circuit. Traditional measures like grade and recovery are useful for monitoring flotation operation but this data lacks the depth to determine the root cause behind operational issues. Determining the operating parameters and ore floatability provides the operating plant metallurgist better tools to assess and manage these issues."

Jan 1, 2006

By Euler De Souza

The authors conducted a study of backfill practices in underground mines across Canada to assess the current state of backfill usage and to overview potential hazards associated with backfill practice, from preparation to transportation to placement. The primary aim of this study was to cover each component of a typical mine backfill system, and to identify potential incidents leading to the disruption of backfilling operations and any associated corrective actions. This paper, Part I of the study, deals with surface operations consisting of backfill material supply and backfill plant preparation. Part II of the study, which deals with underground operations consisting of backfill transportation and backfill placement, is also presented in these proceedings. A review of safety measures associated with current backfill operations and recommendations for procedures of best practice that should be implemented to reduce fill-related hazards in all mine backfill workplace environments are presented. In general it has been found that system failures normally lead only to minor losses to the operations.

May 1, 2009

By F. T. Cawood

The definition of mineral rents has historically been somewhat unclear, but a growing understanding of the source and composition of the revenues that comprise these rents mean that they can be more easily identified and quantified. Furthermore the way in which the flow of the rents from mineral developments are captured and then distributed has been a point of contention amongst the various stakeholders. Investors, the host government, the resource owners, environmental interests, indigenous groups and land owners are identified in this paper as the principal participants in mineral development and while each is entitled to a portion of the rent, the size of their portions will differ. A competitive rent-sharing model for southern African countries has been established and indicates how the range of stakeholders could be rewarded for their contribution. Acceptance of the sharing ratios amongst the recipients is a function of their understanding of the size of the rent and their position in the hierarchy of stakeholders. At first glance investors appear to receive the largest share of the rent, but they disburse some of the rent to hidden costs, which when all is said and done, means that investors and host governments retain approximately equal shares of the mineral rent. Both the investor and government are faced with the dilemma of how to equitably distribute the rents they have captured to minority stakeholders. Government captures corporate tax, mineral royalties and a wide range of subordinate taxes, but is required to construct policies that will ensure distributional equity among the various levels of government as well as among the provinces that comprise the country. Investors will have to ensure that a portion of the rents they capture are diverted to other stakeholders namely resource owners, environmental interests, indigenous peoples groups and the landowners. This paper identifies the major recipients of rent and provides some indication of equitable distribution ratios for mineral wealth among them?a first step in ensuring that mineral development is compatible with long-term sustainable development and in the best national interests.

Jan 1, 2002

By Paul Staples, Fred Woodcock, Robert Grant, Mike Cooper

"Noranda's Brunswick Mining Division, near Bathurst, New Brunswick, processes 10,500 TPD of complex Cu-Pb-Zn bearing ore. Brunswick uses conventional rod and ball milling techniques to achieve a flotation feed size of 75% passing 400 mesh. Over a two year period, testwork was performed using a Marcy pilot plant ball mill to assess the impact of several key variables on secondary grinding efficiency. Four graded mill charges were used to compare balls and slugs at 25 and 29 mm sizes. Data was evaluated by determining grinding rates using a commercially available steady state simulator. Results were critical in Brunswick's efforts to achieve finer grinds while minimizing cost per tonne.IntroductionBackgroundThe Brunswick orebody is an extremely fined grained volcanogenic massive lead, zinc, copper, silver, iron sulphide body between two metamorphosed sedimentary and felsic volcanic rock units. Pyrite content is about 60% with 20% non-sulphide minerals, mainly silica and chlorite.Size reduction at Brunswick is performed by three separate parallel lines consisting of rod mills, primary and secondary ball mill circuits, all in series. The line 3 grinding circuit is presented in Figure 1."

Jan 1, 1997

By D. Bedell, J. Robitalle, D. Macgilliveray

Agnico Eagle (Cadillac Quebec, Canada) selected the new Eimco PEC E – CAT™ clarifier thickeners for their counter-current decantation circuit, which handles approximately 200tph leached gold/silver ore. The E-CAT is based on rakeless ultra-high rate thickening technology that originated in South Africa. Four 9m diameter and two 10m EIMCO E – CAT ultra high rate, rakeless thickeners were installed in the fall of 2000. Thickening and clarification performance has been excellent. Problems with level control have been resolved and the plant personnel continue to improve the operating control techniques. The CCD circuit is critical to the success of the operation and good recovery. Data will be presented showing the wash ratios and recovery achieved. A brief history of the operation and the decision to utilize the CCD system will be presented.

Jan 1, 2002

By Carl D. Ealy

Work is being done to web enable the FHWA Deep foundation Load Test Database. Originally designed to function in the client server environment via modem, access to the database both for data maintenance and user queries has been upgraded to take advantage of the Internet and current and future information technology innovations. The DFLTD will be part of an Automated Geotechnical Information and Design Aid System, the object of which is to assist those involved with managing and maintaining our nation's highway infrastructure. The system will also meet the needs of university and other research institutions for a statistically meaningful source of high quality data for the development and verification of improved analysis methods, in-situ testing methods, etc.

Jan 1, 2002

By D Kilkenny

Underground contractors in the mining industry must be prepared to take a position at the forefront of innovation of equipment and work methods in order to maintain a competitive advantage over in-house operations and remain relevant. Innovative concepts such as split-feed development jumbos, high capacity trucks and loader guidance systems were implemented by contractors to stay ahead of ‘the pack’. All of these are now common across the industry.The demands of regular participation in competitive tendering coupled with aggressive fleet depreciation, means contractors tend to have more communication and opportunities to work with equipment suppliers than mine owners. Therefore, they are more likely to influence equipment design and product directions. They also have a unique opportunity to assist in trialling new concepts and technologies across a wide variety of operating conditions rather than being restricted to one mine.In addition, as a ‘guest’ on a mine site, mining contractors do not have the luxury of creating the environment for their preferred systems, rather they must have the capacity to adapt their technology to suit the offered environment at a particular mine. This leads to a pursuit of adaptive technologies that can be implemented selectively and seamlessly without excessive disturbance rather than ‘all-of-mine’ systems. These incremental innovations then become available for use across the mining industry where they can add value as ‘bolt-on systems’ to existing operations.Mining contractors, therefore, act as the bellwether for industry practices and equipment. However, in order to maintain their position they must engage industry stakeholders to deliver practical, innovative and cost-effective technologies that add value and result in an improved bottom line for all. This paper uses case study material to illustrate how the Byrnecut Group has approached innovation and how the theory of Disruptive Technology applies to underground mining innovation.CITATION:Kilkenny, D, 2017. Innovation in mining – a contractor’s role, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 59–68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

This paper examines the reform of mining legislation over recent years, the establishment of new Crown land management agencies, and the role of the Crown and environmental groups in nature conservation inNew Zealand. It describes the relationship of the minerals industry to the Department of Conservation and environmental groups over recent years, and the prospects for mineral development on the Conservation Estate in future.

Jan 1, 1995

By G J. Corbett, T M. Leach

Although hosted within an Ordovician magmatic arc, the Peak Hill high sulphidation system displays features typical of youngerPacific Rim high sulphidation epithermal gold deposits. Regional NW trending transfer structures are inferred to localise the magmatic source at their intersection of the NS trending arc. Fluids have migrated from the magmatic source along NW structures and thence exploited permeable horizons, which have become silicified. Alteration displays typical zonation from silicification through assemblages characterised by alunite, pyrophyllite and kaolinite and is followed by breccia/fracture controlled sulphide and gold deposition. Sinistral rotation on the NS arc has dilated NW trending fractures to produce the WNW to EW dilational fractures which host the higher grade ore. Mineral assemblages are typical of formation distal to the magmatic source in an epithermal environment. The combination of alteration and mineralisation zonation with structure provide fluid vectors which target a magmatic source to the SE of Peak Hill.

Jan 1, 1995

By K. Sørli, H. Elstad, I. M. Skaar, A. Hildal

Generally, monitoring of refractory furnace linings is of interest to the metallurgical industry. The main issues are to control wear of the furnace lining and break out of molten metal. Penetration of molten metal through the lining can cause considerable damage to equipment in the vicinity of the furnace and endanger operators. Rebuilding of a furnace lining is expensive, mainly because it stops production, but also because the lining materials are expensive. Here, two methods for monitoring the lining of a smelting furnace are presented. The methods are based on monitoring of the temperature distribution in the lining, more specific monitoring an isotherm in the lining. One method is based on the assumption of unidirectional heat flow locally, reducing the problem to a set of one-dimensional heat conduction problems. The other method is based on inverse heat conduction. In this context inverse heat conduction means estimating the wear from temperature measurements using mathematical optimization techniques. The study is based on the ilmenite smelting furnace at Tinfos Titan & Iron KS. Some results from real temperature measurements and real observations from the ilmenite smelting furnaces is presented.

Jan 1, 2003

By J. C. Edwards

The National Institute for Occupational Safety and Health (NIOSH) implemented a real-time neural network system which can discriminate mine fires from nuisance diesel emissions as part of an atmospheric mine monitoring system in NIOSH?s Safety Research Coal Mine. The real-time response of a neural network to fire sensor outputs was demonstrated for coal and belt combustion in the presence of diesel emissions. The fire sensors consisted of an optical path smoke sensor, a carbon monoxide (CO) sensor, and two types of metal oxide semiconductor (MOS) sensors. The real time neural network was trained with coal, wood, and belt fire experiments with and without diesel emissions background. The trained neural network successfully predicted mine fires with these combustibles in the smoldering stage prior to the onset of flames.

Jan 1, 2005