Search Documents

By D. Drymonitis, G. Gialoglou

"Placer gold mineralizations have been observed in the north-eastern parts of Greece. Some of them have been at first evaluated to be of special interest so, exploration campaigns have been designed and carried out. Among the other exploration techniques applied on the sites of interest, drilling was the one to give the detailed information and data for the evaluation of the deposits. Having collected the data from trenching and two consecutive drilling campaigns, they were processed geostatistically to estimate the ore reserves and therefore the economic interest of the deposits. The latter was done by using exploitability indices, which would give a rough idea whether the deposits were economically feasible. A small number of such deposits have been spotted in the area and have been explored and evaluated as above. The present paper deals with the most important of them, giving all the process followed and the results derived from the exploration carried out."

Jan 1, 2005

By K. M. Godiwalla, S. Ranganathan

The thermal state in submerged-arc furnaces (S.A.F.) producing ferro alloys is important for the conditions of both the grade of alloy produced as well as specific energy consumption. The temperature profile in the S.A.F. is affected by the endothermic chemical reactions and the rate of gas evolution. The gas evolution commences at about 900 C due to the reduction of iron in the ore. A first-principle-based 2-D model has been developed to predict the temperature profile in the furnace. In this study, four ores of different grades have been considered in order to simulate the thermal profile in the S.A.F. The influence of the composition of the ore on the thermal profile and its significance in rationalisation of charge distribution to optimise the process are discussed.

Jan 1, 2007

By L. J. Olivier

The possible closure and subsequent flooding of South Deep Gold Mine?s (SD) neighbouring Randfontein Estates Limited No. 4 Shaft (REL 4) necessitated the construction of five concrete plugs in the connecting tunnels to prevent the ingress of groundwater into REL4 from flooding SD. This paper describes the proposed controlled flooding of REL 4, the planned in-service monitoring of the five plugs and the water barrier between REL 4 and South Deep Mine, and the long-term maintenance of the plugs and rock mass in the immediate vicinity of the plugs.

Jan 1, 2006

By R Crookes

Mine to Mill optimisation is not a recently developed concept. It is one which is finally gaining greater acceptance in the Australian Mining Industry, possibly as a consequence of the downturn in markets and certainly made possible by the development of tools and techniques to measure and predict performance of mining equipment and milling plants. Fragment size after blasting has a major bearing on the performance of all aspects of mining and a major influence on the economics of the mine and mill. The process to optimise fragmentation consists of identifying the key factors, measuring their sensitivity through a modelling and trialing program and conducting economic evaluations on the changes on both the mine and mill. Management of the Ernest Henry copper-gold mine in NorthernQueensland, Australia, has espoused the Mine-to-Mill concept and isactively pursuing excellence in blasting to drive down the total cost of mining. Ernest Henry has extremely hard, wet and heavily jointed geological conditions, and had high powder factors and a large percentage of oversize material reporting to the crusher or ROMstockpile. A blasting improvement program was undertaken betweenErnest Henry Mining, Thiess Contractors and Orica Explosives tooptimise the ore size distribution, particularly the oversize component, as a step to reducing production costs. Measures of success included bringing the rock breaker back from double shifts to part-time operation and increasing direct dumping into the crusher from 70 per cent to 92 per cent. Tools and technologies to predict and measure the performance ofindividual blasts are needed before it is possible to optimisefragmentation or the downstream processes. These include suchspecialised Orica Explosives tools as SABREX, POWERSIEVE, andPOWERLINE and commercially available drill monitors. As importantare the more common still and video camera, borehole loggers,measuring tapes, surveying equipment such as face profilers, and ahigh-speed camera if possible. There are many tools which can be applied however it is rarely necessary or possible to use all of them due to time constraints and a point of diminishing returns. The critical point is knowing what the true parameters of the blast were compared to design - only then can the predictive tools be effectively utilised. Stage one of the program has seen gradual improvement as theunderstanding grew and practices have been implemented resulting inreduced bridging in the crusher, geological mapping with respective blast designs and the oversize component under control. This paper is about a process approach which links tools and technology to understand the fragmentation drivers and then to optimising the size distribution.The continuous improvement program continues...

Jan 1, 2000

By Erik Westman

Few studies have been conducted regarding the location, movement, and relative magnitude of the rear abutment of a longwall coal mine. The rear abutment, or the abutment pressure arch in the gob area, is controlled primarily by the quality of pack of the gob; the more compacted the gob is, the larger the stress would be theoretically. While there is no definitive location for the rear abutment, early studies showed that it could be located as far back in the gob as 300 m (1,000 ft). Like the location of the rear abutment, there has been little research conducted and very few answers as to the exact magnitude of the rear abutment load. Due to the fact that the rear abutment has been studied considerably less than the front or side abutment, the need for further studies is evident. From a ground control standpoint, the location and magnitude of a rear abutment could reveal information on the caving process associated with longwall mining, such as when the initial cave could be expected to occur in future panels. Besides the possible importance of the rear abutment from a ground control perspective, evidence related to the longwall rear abutment could be vital from a ventilation standpoint. The peak rear abutment location could serve as an area for harmful gases, such as methane, to accumulate because forcing air through repacked rock is more difficult than through loose rock. The objective of this study is to determine whether passive seismic tomography could image the location, movement, and relative magnitude of the rear abutment as the longwall face retreated, in addition to the forward abutment and gob. The results of a passive seismic imaging study at a western US longwall show evidence for the location, movement, and relative magnitude of a rear abutment. A clear zone of highlystressed strata is shown where the forward abutment is expected and a low-velocity, damaged zone is shown behind the face where the gob is located. These two zones retreat with the face over a three-week period. In addition, the images show a return to stress levels behind the gob that are slightly higher than overburden stress levels, which is presumably the rear abutment. This occurs at a distance behind the face that is approximately the same as the face width for this mine. We can conclude that passive seismic imaging can be used to identify the location, movement, and relative magnitude of the rear abutment of a longwall mine. This conclusion is dependent on the use of appropriate data collection and processing methods. The information provided can benefit the both ground control and ventilation engineers as they strive to improve the safety and efficiency of longwall mines. The knowledge associated with the rear abutment of a longwall could not only help increase production through proper initial planning and reduce down time, but it could also make positive strides in improving the overall safety surrounding a longwall mining operation.

Jan 1, 2012

By A. Hiltunen, R. Hiltunen

The utilization of blast furnace and BOF slags has long traditions and well-known applications in the building and road construction industries and in soil conditioning. The starting point for product development has been the basic physico-chemical properties of slags. This development has led to the almost 100% utilization of blast furnace slags and also considerable amounts of steel slags. While new methods and applications are continuously being looked for and developed in order to recycle and utilize all types of slag, there is at the same time an increasing debate over the exact nature of the slags, whether they are products or waste material, and whether they should be considered substances or preparations. These questions have emerged as a consequence of the environmental effects of the slags and current environmental legislation. The environmental effects of slags can be seen to be both beneficial and less beneficial. There is no doubt about their benefits in the road construction industry, as they allow significant savings in terms of natural materials and in transportation. It is also a known fact that using slags as fertilizers and in the cement industry leads to reduction in CO2emissions. The less favourable effects are the possible harmful emissions into the soil and groundwater. In this paper we describe the properties of slag products and their environmental effects according to investigations carried out in Finland. Keywords: utilization, blast furnace slag, steel slag, properties, solubility, environment

Jan 1, 2004

By M. Olalde, I. Watson

"The consequences of ineffective mine closure in South Africa are evident from the number of abandoned mines and operations on extended care-and-maintenance, the on-selling of mines to less well-resourced companies to close, and increasing illegal mining activities. However, the data to substantiate these observations and provide insight into the underlying issues has not been available. Through the Promotion of Access to Information Act, a list of mine closure certificates applied for between 2011 and 2016 and a list of certificates granted over the same period for all nine regions of South Africa was obtained. From the analysis of this data, we show that the mine closure system as implemented in South Africa is largely ineffective. Although closure certificates are being granted, these are for prospecting sites and small-scale mines, which have a relatively small environmental impact. No large mines of any environmental significance were relinquished over the period under review, with very few applying for closure certificates. Furthermore, the issuing of closure certificates varies significantly between regional offices, with the success rate for applications being generally low and issuing of certificates taking an extended period. IntroductionThere are a number of concerns with the mine closure process as practiced in South Africa, and these have largely been laid at the door of government. Alberts et al. (2017) stress that the legislation generally conforms to international best practice. However, the system is ‘complex and unwieldy’, involving various pieces of legislation and different government departments with overlapping requirements and different interpretations of the law. A further area of concern is the capacity and competence of government to implement legislation. The ‘shortage of relevant mine closure skills and knowledge within the regulator’ was identified by van Druten and Bekker (2017) as a key contributor to unsuccessful closure. Lack of capacity and resources within the regulator has also been highlighted by Botham, Kelso, and Annegarn (2011) and Milaras, McKay, and Ahmed (2014). A recent study of the mineral application process by Corruption Watch (2017) indicates that positions in the regulator have been frozen for many years, leading to a shortage of staff, and that unqualified individuals have been appointed. There is also the perceived reluctance of government to grant closure in order to limit transfer of the liability to the state and delay the inevitable job losses."

Jul 1, 2019

By S. Schwartz, T. Bilney

"Over recent years a number of techniques have been developed as part of the AMIRA1 P9 project to represent mathematically or measure directly sub-processes occurring in flotation cells. These include the determination of:•,?a machine parameter (bubble surface area flux, Sb);•,?a froth parameter (froth recovery, Rf );•,?entrainment and drainage parameters (???and d); and•,?an ore floatability parameter (Pi).These flotation parameters allow the plant engineer to develop a model of the flotation circuit that can be used as a powerful tool to diagnose the performance of that circuit. The recently developed JKSimFloat V6 flotation simulator uses these parameters to predict the flotation circuit performance that would arise from changes in operating conditions and circuit configuration.This new flotation technology was applied to the Placer Kanowna Belle Gold Mine in Western Australia. A series of plant surveys, cell characterisation measurements and laboratory batch tests were conducted to determine the flotation circuit model parameters to be used within the JKSimFloat V6 simulatorA thorough flotation circuit analysis was then performed at Kanowna Belle using JKSimFloat V6. The recommendations that were provided by this circuit analysis have resulted in large improvements in the flotation performance at Kanowna Belle. These include a 1.3% increase in flotation gold recovery and a substantial decrease in operating costs. The analysis is still ongoing, however, the benefits already obtained from applying this technology have resulted in a US$1.3 million a year improvement to the mine."

Jan 1, 2005

The practice of pumping gases which inhibit combustion for purposes of controlling or extinguishing mine fires is now universally accepted. The practice has been used many times in coal mines in India and the experiences are reviewed. The procedures relating to a membrane based nitrogen generator and to a combustion gases generator are described. The physical properties, practical requirements and economic implications of using different gases is briefly reviewed. Some aspects of the practice as related to mine fires in certain collieries in other countries are dealt with.

Jan 1, 2000

By B. M. Loftus

An investigation into the use of impinging stream (jet) reactors for the leaching of a free milling ore produced an increase in gold recovery by 10% while decreasing leaching time by up to 90%.Tests on refractory ores demonstrate no apparent improvement in recovery. However, leaching kinetics are dramatically increased when these ores are subjected to jet reaction prior to agitation.

Jan 1, 1997

By S. E. Olsen, K. Tang

Slag-metal and slag-metal-gas heterogeneous equilibria involving MnO-containing slags have been simulated using recently developed Mn-based alloy and IRSID oxide thermochemical databases. A large number of experimental equilibrium data have been used to verify the calculation results. The experimental slag-metal and slag-metal-gas equilibria in MnO-SiO2binary, MnO-SiO2-CaO and MnO-SiO2-Al2O3ternary, MnO-SiO2-CaO-Al2O3quaternary andMnO-SiO2-CaO-Al2O3-MgO higher-order system can be reproduced within experimental uncertainties. The influence of temperature, CO partial pressure and slag chemistry on the Mn-and Si-distribution equilibria have been quantitatively evaluated. This leads to a sound basis for optimizing the manganese ferroalloy production processes. Key words: MnO-containing slag, manganese ferroalloy, equilibrium simulation, thermochemical database

Jan 1, 2004

By K. Morita, N. Sano

Thermodynamic properties of chromium oxides in molten slags are very important for optimization of stainless steel refining processes as well as reduction processes of chromium ores. The solubility of chromite into molten slags has been found to vary considerably with oxygen partial pressure and slag composition in former studies by the authors. In the present study, activity data and redox equilibria of chromium oxides measured under moderately reducing conditions, PO2= 6.95x10–11atm, at 1873 K are summarized. For the CaO-SiO2-CrOXsystem, the activity coefficient of chromium oxide increased with increasing basicity, and the optimized slag composition for stainless steel refining is assessed as that saturated with CaCr2O4and Cr2O3usingthe phase relations determined. On the other hand, the presence of MgO and Al2O3brings about different behaviour of chromium oxide activity and redox equilibiria and the 44 mass per centCaO-39 mass per cent SiO2-11 mass per cent Al2O3-6 mass per cent MgO slag is recommended toreduce the chromium oxidation loss in the practical stainless steel refining process at 1873 K. Keywords: chromium, activity, stainless steel, AOD, VOD, oxidation loss, redox, CaO-SiO2-Al2O3-MgO slag

Jan 1, 2004

By Bradford C. Wesstrom, Ricardo Parra

The Freeport McMoRan El Paso Refinery uses co-generation to produce some of its electricity and all of its steam. This paper will cover the operation of the co-generation plant natural gas turbine at a fixed RPM for blade longevity and energy output. The by-product heat from the turbine passes through boilers with additional heat from a duct burner to produce steam for the Tank House and auxiliary operations. The steam demand varies dramatically throughout the day based on unloading activities in the Tank House. The use of an automated steam control system within the El Paso Refinery will help stabilize line pressure by incrementally controlling steam consumption based on electrolyte temperature. This will minimize steam line pressure fluctuations. INTRODUCTION In the mid 1920’s the Nichols Copper Company of Laurel Hill, New York recognized the need for a modern copper refining facility in the southwest. Due to the many railroad heads, affordable power and abundant labor supply, and the close proximity to regional copper smelters in Mexico, Arizona, and New Mexico, El Paso became the logical location. In December 1928, ground was broken for the joint venture refinery between the Nichols Copper Company, Phelps Dodge, and the Calumet and Arizona Mining Company. In September 1930, Nichols Copper Company became a part of Phelps Dodge Corporation after a stock exchange. In July 1938, Nichols Division officially became Phelps Dodge Refining Corporation. In March 2007, Freeport McMoRan Copper & Gold acquired Phelps Dodge. Energy costs (electrical and thermal) are critically important in the viability of modern copper electrorefineries. The El Paso Refinery produces electricity and steam through its cogeneration system. The El Paso cogeneration facility is a natural gas, 15-megawatt facility containing five turbine generators and associated waste heat recovery boilers. The facility is divided into two phases. Phase I consists of two Allison 2.2-megawatt turbine generators. Phase II consists of three Solar Taurus 3.5-megawatt turbine generators. Presently three units in Phase II are operated. The Phase I units were purchased and installed in 1986 and the Phase II units in 1992 (Solar 1991). The facility operated at full capacity until 2003 when steam demand was significantly reduced due to decrease in cathode production and closure of the copper sulfate and precious metal operations. Phase I units were taken out of service and put on care and maintenance status.

Jan 1, 2019

By Scott Orenstein

Construction blasting has allegedly been the cause of property damage in the following situations: (1) When the detonation of the shot hurls rock and debris into the air that causes property damage upon impact; and (2) When property owners notice cracks in their walls and foundations after they experience the momentary vibrations that coincide with the detonation of the shot. The current state of the law for both these situations is firmly established. Blasting is classified as an abnormally dangerous activity, for which the blaster is held strictly liable, whether the damage is the result of flying debris or vibrations and concussions generated by the blast. It is when the alleged blasting damage is supposedly from concussions and vibrations, however, that the courts usually reach the wrong result. The typical scenario involves property owners that thoroughly investigate their property after feeling blast generated vibrations, and find cracks that they believe did not exist beforehand. Most often the truth is that the property owners have never noticed these cracks before because they have never looked that closely before. Any structure has a certain number of cracks due to a variety of causes, such as settlement overtime and temperature and humidity changes.

Jan 1, 2004

By P. Sharma

Longwall panels facing wind blasts have been investigated at both Newstan and Moonee Collieries in the Newcastle Coalfield under the Wind Blast Project of the School of Mining Engineering, The University of New South Wales. The fluid mechanics involved in the compression and expulsion of air during wind blasts have been defined and the overpressure and air velocity time histories utilized to determine the wind blast parameters and define the relationship between them. The characteristics of wind blasts pressure pulses in mine roadways show some similarity with transient phenomenon like air blasts from explosives and shock waves from the failure of pressurized vessels. The peak wind velocities in roadways, however, exhibit marked deviations from theoretical predictions based on compressible fluid flow and Rankine-Hugoniot relationships applied to goaf air displacement and panel geometry. Peak overpressures and wind velocities have shown a positive correlation with the areas of goaf falls, with the values peaking off for larger areas. The field investigations have helped the mine management in risk assessment and in evaluating the success of induced caving by hydrofracturing to mitigate the hazard.

Jan 1, 2004

By S L. Birch, M D. Raven

X-ray diffraction (XRD) is a well-recognised, invaluable tool to provide detailed mineralogical analysis on a wide range of applications. However, despite the wide use of XRD in many industries, there are currently few recognised standard methods for quantitative XRD analysis and none for the analysis of iron ore materials. An initial step towards preparing a standard method for XRD analysis of iron ores was to assess the current level of precision achievable by practitioners of the technique by organising an international round robin. Six Australian chemically certified iron ore reference materials were distributed to over 100 international participants. A summary of over 120 data sets from more than 80 participants is presented. Results show that a bewildering array of techniques for sample preparation, data collection, phase identification and quantification were used. The reported values for the main components (ie hematite, goethite, quartz and amorphous content) show not only extensive variability between participants but also within participants’ results for those who submitted multiple data sets. The disappointing low level of precision exhibited for a relatively simple mineral phase system indicates a strong requirement for development of a standardised procedure.CITATION:Raven, M D and Birch, S L, 2017. Summary of results of an international X-ray diffraction round robin for mineralogical analysis of iron ores, in Proceedings Iron Ore 2017, pp 599–604 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By K. C. Mills, R. Thackray

A test has been devised that can predict accurately the % crystallinity developed in a slag film formed between the steel strand and the mould. The % crystallinity in the test samples was determined and compared with that for slag films formed in the mould when casting with that flux. There was good agreement between the % crystallinity in the test samples and the slag films. It was found that additions of TiO2and ZrO2had little effect on the amount of crystalline phase formed, but additions of CaO caused a dramatic increase in the amount of crystalline phase formed. Various parameters (which can be calculated from chemical composition of the flux) have been plotted against % crystallinty in the test samples. It was found that the modified (NBO/T) ratio provided the best relation with % crystallinity for the various parameters tested. There commended relation is % crystallinity=141.1(NBO/T)-284.0. Keywords: continuous casting, mould flux, slag film, crystallinity, chemical composition

Jan 1, 2004

By Ernie Doell, Trung Nguyen

"In early 1995 Cluff Mining commissioned a newly constructed high density tailings thickener at its Cluff Lake uranium mill. The 85 ft diameter high density thickener is one of the first of its kind in North America, and incorporates the novel paste technology in its design to produce densified (in the range of 60 -65% solids) mill tailings suitable for stable deposition in the tailings management area. This paper discusses the impetus behind the installation of such an unconventional thickener, and the many trying experiences in making it operational.IntroductionCluff Mining, a wholly owned subsidiary of Cogema Resources Inc., is the operator of a uranium mine and mill complex at Cluff Lake which is located in northern Saskatchewan. Since 1980, the company has developed and mined out several different ore bodies within the Cluff Lake region for the production of uranium concentrates, commonly known as yellow cake. Based on the known ore reserves, the Cluff Lake operations are projected to last till the early 2000's.Tailings from the Cluff Lake mill have been discharged to a tailings management area consisting of a tailings pond and two facilities for primary and secondary treatment systems. The tailings pond has an impervious bentonite lined dam, and it is divided into a solids and a liquids holding areas. Until the beginning of 1995, the mill tailings were discharged in two separate lines to the solids pond; one line carried the slurry residue of 45-50% solids (w/w) from the CCD circuit, and the other discharged raffinate tails containing less than 1 % (w/w) gypsum precipitate. Supernatant in the solids pond is treated in the primary treatment system prior to discharging to the liquids pond. Figure 1 shows the site plan of Cluff Lake tailings management area.It has been estimated that by the end of 1995 the solids pond would be filled to about 60% of its design capacity, and probably would be full before the year 2000. Therefore, Cluff Mining had to consider a more efficient tailings disposal method that could extend the service life of the existing Cluff Lake tailings management area. A high density tailings thickener was believed to be the most practical and economical system for tailings disposal at Cluff Lake mine."

Jan 1, 1996

By A. Karadogan, G. Tuncer, A. Kahriman

Determination of optimal blast parameters have been the priority act for blasters on the field due to financial and technical properties of the operation. Therefore many researchs were done to establish a general formula for many years. These intends could reach some empirical and numerical design frames consisting the rock, geology and explosives properties. Blasting parameters have to be adjusted according to the desired fragmentation rate especially on the mines where particle size distrubition after blasting has a great importance. Therefore the blast designs have to be evaluated considering the particle size distribution after the blasts. The Kuz-Ram model which was modified by Cunningham is one of the tools for estimating the particle size. Although it doesn’t give an accurate result, it can be very succesful on modifying the blasting design parameters by establishing a back correlation between the blasting parameters and the exact particle size distribution results which can be easily achieved by digital image processing system. Within the scope of this study, the particle size distribution after blasting was assessed by Split-Desktop digital image processing system and bench blasting parameters were studied considering the desired particle size distribution at Espey colemanite mine using Kuz-Ram and digital image processing system combination to determine the specific blasting parameters for this site.

Jan 1, 2005

By J. M. Font, R. G. Reddy

Jan 1, 2004