Search Documents

By G D. Price

Scheelite mineralisation east of the main divide in' the Southern Alps of New Zealand was originally identified by Royden Thompson who is now a geologist with the NZ Geological Survey. This mineralisation was brought to the attention of CRA in 1978. Reconnaissance surveys were carried out in 1979 to delineate the extent of the mineralisation. This was undertaken using ultraviolet light examination of the sediments within the major drainages in the Southern Alps. This defined tentative zones of prospective mineralisation. As a result of this, preliminary reconnaissance, exploration licences were applied for -those areas in which indications of scheelite mineralisation were strongest. A total of 1737 km2 of ground was applied for within four exploration licences. These covered the main Southern Alps mountain chain between the Haast/Wanaka highway and the Mt Cook National Park.

Jan 1, 1983

By K. G. Matshika

"Nickel electroplating from sulphate electrolyte is an efficient process. To achieve good quality cathode, however, parameters such as temperature, nickel concentration, pH, electrode alignment, electrolyte flowrate and additives must be optimised, because these affect cathode morphology and current efficiency. It is also important to control the clarity and contamination of the electrolyte, as these have a considerable effect on the quality of the cathode surface. Delamination, surface roughness and pitting on the cathode surface can be caused by incorporation of solid particles or impurities form the electrolyte. Three types of solid particles were investigated: cuprous selenide, barium/ lead sulphate (co-precipitated) and ferric hydroxide. These particles can be found in industrial electrolytes, especially if there is a problem with the filtration step or contaminants have reacted to form insoluble particles. A rotating cylinder Hull cell was used for this investigation. It is found that the effects on morphology depend on the type of solid, concentration, particle size, current density and electrolyte flowrate. Cuprous selenide is the most detrimental, especially at higher concentrations, higher current densities and low flowrates. Increased rotational speed offers a uniform sheet of fine gas bubbles across the surface of the cathode which reduces the thickness of the diffusion layer of liquid adjacent to the cathode and increases the rate of mass transport to the cathode from the bulk liquid. INTRODUCTION Electrowinning operations are important when recovering associated by-products of nickel production, such as copper, cobalt and zinc, from pressure leach solutions. The base metal mineralization associated with platinum-group metal (PGM) production yields significant quantities of copper and nickel as by-products. The base metal refinery is vital in PGM processing as it increases the PGM concentration from mined ore by a factor of 400, in comparison with concentration by flotation (20 times) and pyrometallurgical processing (20 times) (Crundwell et al., 2011). Anglo American Platinum Ltd produces nickel cathodes by electrowinning and purges sodium from the base metal refinery in the form of sodium sulphate at the Rustenburg Base Metals Refinery (RBMR), as shown in Figure 1. This is the Sherritt acid leach process used in most base metal refineries to ensure no loss of PGMs and shows the subsequent purification steps for copper and nickel. Other refineries in Zimbabwe, such as Bindura and Empress, use the Outokumpu leach process (Pavlides, 2001)."

Jan 1, 2015

By P Grieve, J L. Mauk

The Central Maratoto Valley in the Coromandel Peninsula contains a sequence of veins in pervasively altered dacite + andesites of the Waipupu Formation. We recognise at least eight different vein types: (1) pyrite stringers, (2) quartz + carbonate veins, (3) crystalline quartz veins, (4) carbonate veins, (5) chlorite + carbonate veins, (6) siderite veinlets, (7) siderite + carbonate veins and (8) carbonate + pyrite veins. The overall temporal trend of the veins is from early pyrite to quartz and then to late carbonate veins. Carbonate veins and pyrite stringers both form planar and irregular veins, whereas some carbonate veins have diffuse contacts with the wall rock. Gold and base metal sulphides are associated with some of the quartz + carbonate veins. Textures within the veins reflect open space filling and multi-phase reopening. A partial record of hydrothermal activity has been preserved by vein crosscutting relationships, hydrothermal alteration minerals and fluid inclusions. Hydrothermal alteration minerals display zonation from south to north. The alteration increases from unaltered to weak propylitic alteration of andesite in the south (MVRCDC1), to sericitic alteration of andesite and dacite in the north (MVRCDC3). The alteration assemblage is dominantly sericitic, with no adularia present, drawing parallels to the Thames region where there is no adularia.

Jan 1, 1999

By J. Hollow, D. Walsh

The Fort Knox Mine is located in Alaska’s interior, where the average ambient air temperatures range from -24oC in January to 16oC in July. The mill processes a free milling gold ore utilizing both a gravity recovery circuit and a conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leach, carbon adsorption and cyanide destruction kinetics. Additionally, an energy balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post project plant performance that validates the model and shows the mine produced an additional 596 kg (19,155 ounces) of gold, while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007

By G H. Clark

Batu Hijau is a porphyry copper-gold deposit located onSumbawa Island in the western Banda Arc of Indonesia. The deposit has been evaluated from 54 000 m of drilling in 105 diamond drill holes over a surface area of 1.2 km2 and to a depth of 1000 m below surface (412 m below sea level). A provisional plan is being evaluated to mine 642 million tonnes at an average grade of 0.61% Cu and 0.55 g/t Au (variable cut-off) from an open pit in the higher grade portion of the resource.   The deposit is associated with a calc-alkaline intrusive complex that was emplaced in a thick sequence of andesitic pyroclastic rocks. The oldest and most widespread intrusion is porphyritic to medium-grained, equigranular, quartz hornblende diorite. At Batu Hijau the western diorite contact zone was intruded by two phases of tonalite. The older tonalite is a stock increasing from 200 m diameter at surface to 500 m at sea level. It consists of quartz, plagioclase and hornblende phenocrysts set in a groundmass of similar composition. A younger tonalite intrudes the tonalite stock, quartz and plagioclase phenocrysts are more abundant and it has a finer groundmass than the older tonalite. Brecciation occurs near the older tonalite contacts but there are no breccia pipes or late-stage features such as pebbledykes or postmineralisation intrusive rocks.   Hydrothermal alteration of Old Tonalite and adjacent rocks is centred on the Old Tonalite and is zoned from a core of pervasive potassic alteration grading to an outer propylitic halo. At depth a propylitic assemblage is developed in the low grade core in the Old Tonalite. Phyllic alteration, late stage and mainly fracture controlled, overprints both potassic and inner propylytic zones. Intermediate argillic alteration overprinting is widespread, particularly on the eastern side of the hydrothermal system, where advanced argillic alteration overlies argillic alteration.   Ore grade mineralisation is cylindrical in shape, up to 800 m in diameter, and is centred on the Old Tonalite. A high grade shell (>0.75% Cu) forms an upward tapering cone in and around the Old Tonalite and reaches the surface in the centre of the deposit. Lower in the shell >l g/t Au and >2 g/t Ag accompany >1% Cu. Below 75 m above sea level mineralisation in the Old Tonalite rapidly decreases as a weakly mineralised core develops, but the limb continues to contain mineralisation to at least 412 m below sea level. Fracture and vein-controlled chalcopyrite and bornite are the dominant hypogene copper minerals and are the hosts for most of the gold mineralisation. Gold occurs free and in the lattice of the copper sulphides, and has been observed in quartz.   Weathering, especially where argillic alteration is developed, has produced a strongly leached cap, up to 147 m thick, below which is an irregular copper enriched supergene zone. Where leaching is not developed, such as over the centre of the deposit, an irregular oxide zone and a weakly developed supergene zone may be present.

Jan 1, 1995

By Du Sichen, K. Mukai, S. Seetharaman

Viscosities of slags constitute an important physical property needed for an understanding of the mass transfer phenomena in metallurgical processes. Viscosity is also the key that leads to a better understanding of the structure of slags. It is well known that the viscosities of silicate slags decrease with the addition of basic oxides due to the breaking of the silicate network. The measurements of slag viscosities often pose experimental challenges, especially to the choice of materials. The keynote lecture takes up the experimental problems and the various techniques adopted. Dynamic viscosity measurement, as a powerful tool towards an understanding of the kinetics of some high temperature reactions, is brought out. A number of semi-empirical models have been developed to estimate the slag viscosities in the case of multi component slags. A critical survey of these models is presented in the lecture. Earlier models by Riboud et al., Urbain et al. and Mills et al. have been developed further into a new generation of models. Some of the current important models are (1) Model by Iida et al. (2)CSIRO model (3) Pyro research Model (4) Model by Tanaka et al. (5) Model approach by Reddy et al. and (6) KTH-model. The predictions and capabilities of the various models are compared. Estimations of viscosities from thermodynamic data and prediction of liquidus temperatures from viscosities are presented. The concept of surface viscosities with reference to slags and viscosities of two-phase mixtures are also taken up in the presentation.

Jan 1, 2004

By J. Haynes

Coal mines in the eastern US often use sloped shafts as production beltways for ore removal, as means of access for supplies, and for ventilation. These structures are usually completed with the help of a contractor. In late 2011, Frontier-Kemper Constructors was engaged to build a slope for a coal mine in southern Indiana. Although the site was located in familiar Illinois basin formations, the geology proved to be very difficult. This paper describes some of the challenges faced during excavation of this slope and the methods used to overcome them, including changing the method from conventional drill and blast to cutting with a continuous miner.

Feb 27, 2013

By Enrique Fernández

INTRODUCTION The high speed rail link between Madrid and Asturias, in the North of Spain, has encountered in the Cantabrian range the biggest challenge of the whole line, a very deep tunnel, 25 km long through a foreseen difficult geology. This tunnel was divided in the following four lots for construction: ¦Lot 1: Pola de Gordón- Folledo. L=10,7 km ¦Lot 2: Folledo-Viadangos. L=4,166 m ¦Lot 3: Viadangos- Los Pontones. East tube. L=10,4 km ¦Lot 4: Viadangos- Los Pontones. West tube. L=10,4 km. Dragados S.A. leading a JV was contracted to design and built the Lot 2 on the captioned Pajares High Speed Railway Tunnel. The Lot 2, comprising the middle third section of the 25 km long tunnel has an additional challenge: the construction of one access from the surface to allow it own construction. Feasibility reports and preliminary design do not foresee the use of TBM due to the risk of squeezing ground at the deepest area of the tunnel. On the other hand, conventional NATM excavation of the twin tunnels and ancillary works, including access shafts were against the expected construction schedule by the client, due to the poor ground foresee at the early stage.

By A. Wright, P. Lacombe, R. del Villar, D. Hodouin, C. Sepulveda

"The data acquisition from industrial plants is a fundamental step for process modelling in process optimization, process analysis and automatic control.The introduction, some years ago, of modern distributed control and data acquisition systems in concentrators imposes a new approach in designing experimental schemes for data acquisition campaigns and new criteria for the treatment of the obtained discrete information.This paper presents the methodology applied to sample a zinc flotation circuit at Les Mines Selbaie, Joutel, PQ. Values of 85 process variables were obtained form the Distributed Control and Data Acquisition System (Bailey Network 90) and transferred to the DOS environment. Another 11 variables (flowrates and valve positions) were directly sampled using an IBM-PC compatible computer equipped with a data acquisition card and a signal processing circuit.All variables, under the vector form, were processed in the PC-MATLAB environment to either filter or eliminate the non-linear disturbances and noises, producing useful data for model development. The filtering algorithms are also presented.INTRODUCTIONProcess control does not need to be justified. Whether manual or automatic, any processing plant requires some form of control to accomplish its main objectives: a good quality product and a target throughput. Process control of mineral processing plants has steadily evolved from manual control, where the operator skills and/or experience play an important role, to some level of automatic control, usually considered better, as less human subjectivity is involved, at least when actions have to be taken.The design of these control systems requires the knowledge of the dynamics of the process it is deemed to control. Process modelling is therefore an essential step in the assessment and the design of a control strategy. The choice of model will depend on the available resources and manpower."

Jan 1, 1991

By Joseph Moses Botbol

In passing the judgments essential to his trade, the geologist may be assisted by two new methods. These will enable him to (1) arrange the minerals of a selected group of base metal mining districts in the order of their typicalities and (2) compute the degree of mineralogic association between the model so derived and a district external to the model. It must be remembered, of course, that the methods discussed in this article are no more powerful than the structure of the model used and the data available. The geologist who employs these techniques must still exercise his expertise

Jan 1, 1970

By Andrew P. Schissler

The Citronen Zinc-Lead Project is one of the world?s largest undeveloped zinc-lead resources, containing more than 13 billion pounds of zinc and lead metal. The project is located in northern Greenland, a self-governed region of the Kingdom of Denmark (Figure 1). Citronen is the northern-most mine in the world, operating at a latitude of 83o 3? N. In excess of 67,000 meters of diamond drilling have been completed to delineate the resource. As of January 2012, the measured, indicated, and inferred reserves for the Citronen project totaled 70.8 million tonnes, consisting of 5.7% zinc + lead (3.5% zinc cut-off) (Ironbark, 2012). For the underground mine plan, room-and-pillar and long holestoping mining methods were selected. The beneficial application of structural fill was considered for increased recovery, efficient tailings disposal, and ground control. Three types of fill were compared - paste fill, cemented rock fill, and iced tailings. An environmental and economic feasibility study concluded that iced tailings was the preferred alternative provided it met the ground control requirements. The purpose of this paper is to explain the investigatory steps that led to the possibility for the use of iced tailings as structural fi

Jan 1, 2012

By Kenneth F. Whinery, John M. Campbell

Basically, the Buckley-Leverett theory involves two systems which are similar in nature but are differentiated by time. These systems may be described by the fractional flow and frontal advance equations which essentially characterize the mechanics of oil movement while being expelled from the reservoir. The fractional flow equation originally developed by Leverettl may be expressed in the more usable form The development of this equation is based on Darcy's law describing fluid flow through porous media and applies to the flow at only one point (it is a point function). For simplification, the fractional flow equation is written in the above form because the capillary forces always increase the fractional flow of the displacing phase regardless of the direction of flow or the displacing phase. If, for simplicity, the effects due to gravity and capillary pressure differences are neglected, the fraction of the displacing fluid, f, at any point in the flowing stream is related to the properties of the system by 1 Thus, it is seen that in the absence of capillary and gravitational effects, fd for a given sand and fluids varies only with saturation and pressure. The magnitude of the viscosity ratio, —a has an effective range (range of about 30) in the system where gas is displacing oil and a much smaller range for water displacing oil. In order to make the fractional flow equation more versatile, it is necessary to connect the fractional flow at a given point and saturation with time. This problem was approached by Buckley and Leverett" who developed the frontal advance equation, Eq. 3 states that the rate of advance of a plane that has a fixed saturation, Sd, is proportional to the change in composition of the flow stream caused by a small change in the saturation of the displacing fluid. It is, essentially, a transformation of a material balance equation representing the net rate of accumulation of the displacing phase within a homogeneous sand block. This accumulation is proportional to the difference between the rate at which the displacing fluid enters the sand and that at which it leaves. Eq. 3 describes the velocity with which a plane of constant displacing phase saturation advances through a porous system. Buckley and Leverett," Babson,' Kern," Welge, and others have adequately discussed the basic mechanism and application of the fractional flow and frontal advance equations. APPLICATIONS OF THE FRONTAL ADVANCE THEORY TO PETROLEUM RECOVERY Two general applications of the Buckley-Leverett frontal advance theory involve the system in which the oil is being displaced by an expanding gas cap overlying the oil zone and that in which the oil is being displaced by water. Displacement by Gas in the Presence of an Immobile Water Saturation A system in which gas is the displacing phase may be thought of as having two forces effecting the displacement process. These forces are the gravitational force and that force exerted by the displacing gas. The gravitational effects control the displacing efficiency of the gas. The gravitational effect will be less at higher rates of flow, thereby reducing the effectiveness of the displacement of the oil by the gas. The more efficient displacements occur at flow rates which are less than the gravity free fall rate. Capillary forces can be neglected without materially changing the magnitude of the gas saturation. The Mile Six pool is used herein to illustrate the calculating procedures in evaluating gas drive-gravity drainage field perfomlance. These calculations represent the determination of the gas-oil contact when the distribution of the hydrocarbon pore volume is considered. Two methods

By Masaki Kitazume, Yoshiaki Kikuchi

"Abstract Pile foundation is one of fundamental techniques to improve the bearing capacity and settlement characteristics of superstructures. Wide varieties of piles having various shape, size and material were developed and have been applied to a lot of construction projects throughout the world. The deep mixing method, an in-situ admixture stabilization method, was developed in 1970s in Japan and the European countries, and has been frequently applied to many construction projects for various improvement purposes such as increasing bearing capacity and horizontal resistance, reducing ground settlement, preventing liquefaction and so on. The design methods, execution procedure and quality control and assurance (QC/QA) of the method are standardized or specified in many countries. These standards, specification and/or technical manual have been a remarkable contribution to spread the techniques throughout the world. The QC/QA is one of the major concerns for clients and engineers who have poor or no experience of the technologies. In order to assure the high quality of deep mixing work in the global market, it is necessary to establish the concept of QC/QA and correlate the output of different procedures. Upon the request by the organizing committee of the DFI-EFFC International Conference on Piling & Deep Foundations, the authors conducted survey of the specifications and standards on the piling and deep mixing technologies in Asian countries. In this manuscript, the results of survey are briefly introduced by comparing these specifications and standards.IntroductionThe pile foundation is one of fundamental techniques to improve the bearing capacity and settlement characteristics of superstructures. Wide varieties of piles having various shape, size and material were developed and have been applied to a lot of construction projects throughout the world. The design method, execution procedure and quality control and assurance of pile foundations are standardized in many countries based on the accumulate research results, laboratory and field experiences. In Japan, steel pipe piles are mainly constructed by hammer driven in port construction. On the other hand, precast pre-stressed concrete piles or cast-in-place piles are mainly used in on land construction. When precast pre-stressed concrete piles are constructed, piles are usually set by inner excavation method because of preventing noise and vibration problems. More than 50 years ago, noise and vibration problems had not been serious problem in Japan, but around 50 years ago, they became serious and now less noise and vibration construction methods are used for pile construction on land in Japan. In Asian countries, though piles used for construction have a lot of variety, precast pre-stressed piles are commonly used. In this report, execution controls of construction methods of steel pipe piles and precast concrete piles are mainly considered."

Jan 1, 2014

By Albert L. Toenges

The introduction of mechanized mining in coal mines, which has speeded loading, has emphasized the importance of efficient underground transportation systems. The purpose of this investigation is to study and analyze various systems now in use, and to derive conclusions therefrom. This report may be helpful to operators who are planning new systems of transportation or who are revising present systems to increase their efficiency. This paper is the first of a series on this subject and des¬cribes some systems of transportation `utilizing rail haulage, ACKNOWLEDGMENT The information used in preparing this report was obtained through the courtesy and cooperation of the officials of the companies whose mines were studied. The descriptions of the transportation systems at the mines included herein have been checked for accuracy, and publication of the data has been approved by the executives of the several operating companies.

Jan 1, 1940

By F. Keller, E. H. Dix, L. A. Willey

The consideration of alloying elements for aluminum has led to a series of investigations of the equilibrium relations between aluminum and those alloying elements. Therefore, the aluminum end of the aluminum-antimony diagram has been studied. The general form of the aluminum-antimony equilibrium diagram has been worked out by Campbell and Mathewsi and by Tammann.2 Canlpbell and mathews described principally the beginning of solidification. They found the curve of beginning of solidification rising gradually from the melting point of pure alunlinum to a maximum at about 67 per cent. aluminum. After a slight lowering of the curve at a little greater antimony concentration the curve again rises to a maximum at 18.4 per cent. aluminum, which corresponds to the compound AISb. The curve then drops to the melting point of pure antimony. Tamrriarln explained the maximum occurring at about 67 per cent. aluminum as the result of the slow formation of the single compound AISb. The space lattice of the compound AISb, according to Owen and Preaton,³ is face-centered cubic, the antimony atoms being intermeshed with an identical aluminum lattice. Very little, if any, work has been done on aluminum alloys containing small amounts of antimony. The Present Investigation It has been the purpose of this investigation to determine the solid solubility of antimony in aluminum and also to investigate the eutectic temperature and concentration. The experimental work has been carried out in a manner similar to that described in a previous paper4 from this laboratory.

Jan 1, 1931

By J Fisher, M Castro, A Hariyadi

The train haulage system being designed for PT Freeport Indonesia’s Grasberg Block Cave (GBC) will be located within the mine at an elevation of almost 3000 m above sea level on the west side of the island of Papua, Indonesia. The developing block cave is beneath the active Grasberg Open Pit and will transport 160 000 t of ore per day from multiple chute galleries to the underground crushing plants. The design entails 28 km of rail and 119 ore chutes, which will be brought online over the course of ten years.The train haulage system will be driverless and fully automated. Sequentially, the system includes remote controlled rock breakers at the top of the chute grizzlies, followed by remote controlled chute loading of the trains, then autonomous train haulage and autonomous unloading. An overhead catenary system (OCS) will power the locomotives, which are equipped with on-board batteries to drive through the loading and unloading sections. Service locomotives with drivers move material-laden freight cars in and out of the service shaft, destined for workshops, the magazine and batch plants. Service locomotives are also used for haulage level maintenance. Highly reliable and redundant control and communications systems are required to manage 12 trains in simultaneous operation.This paper provides an overview of the train haulage system’s technical complexities and the associated support systems interactions. The paper also highlights the project management issues and successes of this globally sourced project.CITATION:Hariyadi, A, Castro, M and Fisher, J, 2016. Automated train ore transport, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 563–570 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S. Pinard, J. MacLellan, G. Ehlert

"The Kidd Creek concentrator is looking actively for alternative technology as means of reducing operating costs in their concentrate handling section. The use of pressure and vacuum filters to eliminate the multiple hearth dryers would have the most beneficial effect. The dryers which constitute the greater portion of concentrate drying costs consume about 35,000 m3 per day of natural gas.After the evaluation of various filters by Kidd's technology group, it was clear that, because of the low final moisture requirements of 5.5 to 6% H20, few filters were able to achieve this target economically. Lately attention has focused on the Andritz hyperbaric filter. Testwork has shown that target moistures can be achieved with an appreciable reduction in operating cost.1.0 INTRODUCTIONThe Kidd Creek Concentrator is located 28 kilometers east of Timmins, Ontario. The ore is hauled by the Kidd Creek Railroad to the concentrator where it is milled to produce separate copper and zinc concentrates.Projected concentrator feed for 1991 is 3,750,000 tonnes of ore grading 3.3 % Cu and 4.7 % Zn. The concentrate production is expected to be 458,080 dry tonnes of copper concentrate at a grade of 25.7 % Cu and 265,020 dry tonnes of zinc concentrate at a grade of 54 % Zn.Currently, there is active investigation toward cost reduction through implementation of new technologies. One area which has been extensively evaluated is the concentrate dewatering and drying section. In that section, the multiple hearth concentrate dryers represent the largest source of operating costs, mainly through maintenance and energy costs (electricity and natural gas). The replacement of these dryers with filtration technology that could produce the required concentrate dryness would represent substantial savings.In September of 1990 filtration testwork carried out by Andritz Ruthner showed that Kidd Creek copper and zinc concentrates could be filtered to below 6 and 8 % moisture respectively. In late May 1991 the laboratory testwork was duplicated on siteand one month later a 5 m2 pilot filter was tested on site. Based on the pilot test results, an economic evaluation was performed. It indicated that a reasonable payback could be realized if hyperbaric filters were to replace the existing concentrate drying section."

Jan 1, 1992

By Kourosh Shahriar

The occurrence of rock falls in underground coal mines entails detrimental effects as fatal or non-fatal injuries on workers, stoppages in mining operations and breakdown of equipment. In this paper, a risk assessment approach on the basis of a decision analysis trend is employed in order to assess the possibility of and manage roof falls. Risk is then assessed by determination of likelihood of occurrence and the cost of consequences (outcomes). In this regard, collected real roof fall data from Tabas and Kerman coal regions comprising of several underground coal mines are used. It is concluded that the annual accidents due to the roof falls occurrence in the all investigated mines are so high that it is economically feasible to improve the support systems and to implement a suitable educational program as well as an accurate supervision and other elements of safety management.

Jan 1, 2009

By Steve Dubnewych

The Joint Water Pollution Control Plant, operated by the Sanitation Districts of Los Angeles County, treats wastewater generated by over three million people. A new tunnel and ocean outfall is being considered to meet future hydraulic demands and provide long-term redundancy for the Districts? existing tunnels, portions of which were constructed as early as the 1930s. The detailed process used to evaluate the feasibility of various tunnel and out-fall locations is described. Challenges include a geologic profile with mixed face and squeezing ground conditions; high water pressures; active fault crossings; gassy and contaminated ground conditions; and liquefaction, slope stability, and lateral spreading concerns in the area of the riser and diffusers.

By A. Rejeb, A. Millard

ABSTRACT: An evaluation of the importance of the thermo-hydro-mechanical couplings (THM) on the performance assessment of a deep underground storage design has been made as part of the international DECOVALEX III project. It is a numerical study that simulates a generic repository configuration in the near field in a granite medium. The thermo-hydro-mechanical evolution of the whole configuration is simulated over a period of 100 years. The model used to represent the unsaturated behaviour of the various porous media makes allowance for moisture transfers through the effect of thermal and water gradients. The paper presents a comparison of the temperature, water pressure and stress fields obtained by TM, TH, HM and THM coupled calculations. The results demonstrate that temperature is hardly affected by the couplings. In contrast the influence of the couplings on the mechanical stresses is considerable. This is attributed to the key role that water has on bentonite swelling or shrinkage effects that are dependent on its saturation level variations. KEY WORDS: Modelling, thermo-hydro-mechanical couplings, temperature, pressure, stress. ZUSAMMENFASSUNG : Im Rahmen des internationalen Projekts DECOVALEX III wurde untersucht, wie groß der Einfluss thermisch-hydraulisch-mechanischer Kopplungen (THM) auf die Leistungsfähigkeit eines Konzeptes zur Lagerung hoch radioaktiver Abfälle zu bewerten ist. Bei dieser numerischen Behandlung wird eine generelle Lagerungskonfiguration in granitartigem Milieu simuliert. Die thermisch-hydraulisch-mechanischen Prozesse werden für eine Dauer von 100 Jahren simuliert. Bei dem Modell, mit dem das Verhalten der verschiedenen, unterschiedlich porösen Milieus in ungesättigtem Zustand dargestellt werden soll, werden die Feuchtigkeitstransporte infolge thermischer und hydraulischer Vorgänge berücksichtigt. Verglichen werden in diesem Artikel verschiedene Temperatur-, Wasserdruck- und Beanspruchungsfelder, die sich aus TM-, TH-, HM- und THM gekoppelten Berechnungen ergaben. Dabei stellte sich heraus, dass die Temperatur nur gering von den Kopplungen berührt wird. Die Einflüsse der Kopplungen auf die Mechanik sind hingegen bedeutend; ausschlaggebend dafür ist der Faktor Wasser, der den Bentonit je nach Sättigungsgrad quellen oder trocknen lässt. SCHLÜSSELWÖRTER: Modellbildung, thermisch-hydraulisch-mechanische Kopplungen, Temperatur, Druck, Beanspruchung. RESUME : Dans le cadre du projet international DECOVALEX III, une évaluation de l’importance des couplages thermo-hydro-mécaniques (THM) sur les performances d’un concept de stockage de déchets fortement radioactifs a été menée. Il s’agit d’une étude numérique simulant une configuration générique de stockage en champ proche dans un milieu granitique. L’évolution thermo-hydro-mécanique de l’ensemble est simulée sur une période de 100 ans. Le modèle utilisé pour représenter le comportement non saturé des différents milieux poreux prend en compte les transferts d’humidité sous l’effet de gradients thermiques et hydriques. L'article présente une comparaison des champs de température, de pression d’eau et de contraintes obtenues par des calculs couplés TM, TH, HM et THM. Les résultats montrent que la température est peu affectée par les couplages. En revanche, l’incidence des couplages sur la mécanique est importante; ce qui est attribué au rôle majeur joué par l’eau à travers les effets de gonflement ou de retrait de la bentonite selon la variation de son degré de saturation. MOTS-CLEFS : modélisation, couplages thermo-hydro-mécanique, température, pression, contrainte.

Jan 1, 2003