Search Documents

By Joseph T. Coe, Siavash Mahvelati, Alireza Kordjazi

This paper introduces recent advances in stress-wave NDT systems for use in assessments of in-service foundation integrity and drilled shaft construction. The primary results of the laboratory experiments are very promising, as the acquired image was capable of differentiating changes in pile cross section as low as 0.3 cm. The preliminary results with the same hardware components on a relatively large scale cemented sand model were also promising. A brief overview is provided of both systems including hardware, survey methods, and data processing techniques, followed by a discussion on application of the results to QA/QC of deep foundations. INTRODUCTION There are two main applications in which current QA/QC NDT technology fails to provide sufficient information regarding deep foundation conditions: (1) detection of flaws in outside cover concrete of drilled shafts and corrosion in steel piling; and (2) evaluation of anomalies beneath the bottom of drilled shaft excavations. Previous studies have demonstrated the capabilities of high frequency stress waves for geotechnical and foundation evaluation purposes (Lee and Santamarina 2005; Coe and Brandenberg 2010; Coe and Brandenberg 2012; Coe and Kermani 2016). Higher frequency waves can visualize smaller anomalous features at the expense of higher attenuation and smaller propagation distance. Therefore, the goal of this study was to advance the state of NDT practice by development of a prototype high resolution stress-wave imaging system as proof-of-concept. The equipment and hardware were modular, which allowed simultaneous development of two system configurations for application to in- service foundations as well as drilled shaft excavations during construction. Results are presented based on two large scale soil models. The first laboratory model simulated section loss in an in-service steel pipe pile and drilled shaft foundation (Fig. 1a). The second model simulated anomalous conditions beneath drilled shafts excavations as might be encountered in areas with significant karst (Fig. 1b). For both models, evaluation of foundation conditions relied on the propagation of small amplitude seismic stress waves using hardware similar to those described in Coe and Brandenberg (2010) and Coe and Brandenberg (2012).

Jan 1, 2018

By H. C. Verakis, M. L. Harris, M. J. Sapko, K. L. Cashdollar

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) has developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five and three underground coal mines in MSHA District 2 (PA) and District 11 (AL), respectively. While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (% IC) determined by the CDEM agreed well with those obtained later by low temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

By James J. Graham

Uravan, Ambrosia Lake, Gas Hills and South Texas are all historic names in US uranium. These mining areas supplied the uranium that brought the United States into the nuclear age during the 1960s, and fueled the birth of nuclear energy for peaceful uses — a promise of nearly limitless, clean energy for the world’s future. That promise still exists today, but it is hard to hear over the rhetoric of environmental activists and politicians. Nuclear power offers dependable electricity with limited environmental impact at stable prices. Nuclear power releases no greenhouse gases or particulate matter into the atmosphere. High level nuclear waste (HLW), although long lived, is readily controlled and compact. In the United States, generating 1 billion kWh of electricity with coal produces 47 kt (52,000 st) of solid waste (ash and sludge), compared to 3.6 t (4 st) of HLW produced by nuclear.

Jan 1, 2002

By A. Yu. Lein, V. V. Maslennikov, S. P. Maslennikova, I. Y. u. Melekestseva, Yu. A. Bogdanov

Tellurium is a high-tech and also toxic element. This element shows sufficient contents in Fe-Mn crusts and nodules in the modern ocean to be involved in future industrial processes [Hein et al., 2003]. Tellurium minerals and contents are not well recorded in modern and ancient black smoker systems. Tellurides are rarely found in sulfides from the modern oceans [Iizasa et al. 1992; Maslennikov et al., 2010]. The previous common opinion that tellurium is scarce in active seafloor hydrothermal systems can be revised due to the recent discovery of abundant tellurides in chimneys from Brothers Volcano vent site [Berkenbosch et al., 2012]. We found abundant tellurobismuthite, hessite, and native tellurium in chimneys from Su Su Knoll vents sites (West Pacific). So, tellurides can be found in some chimneys but absent in others. The causes of this are poorly understood. These conflicting data create numerous questions and require an explanation. The problem can be resolved by research at different scales including analysis of relevant genetic features of host sequences, systematic textural and paragenetic studies of different types of chimneys, and their rare mineral assemblages. Paragenetic models, compositional analyses and ranges of tellurium-bearing minerals and the physicochemical interpretation of chimney diversity in different types of VMS deposits are the main subjects of our research. The data on tellurides in chimneys from ancient VMS deposits should also be useful to resolve this problem.

Sep 1, 2014

By G. Naud, J. Robitaille, M. Buonvino, A. Veltmeyer, A. R. Laplante

"A B6 Falcon concentrator was tested on several systems: a synthetic magnetite-silica ore, a massive sulphide gold-copper ore, a fine gold-pyrite-silica flotation tail, and a high grade gold ore in a low sulphide gangue (cyclone overflow).The Falcon demonstrated its ability to achieve separation in all cases, but with varying degrees of success. For the magnetite-silica system, separation proceeds until the concentrate bed overloads, at a mass of 300 to 400 g of magnetite. Recovery increased with decreasing particle size, down to the 25-37 µm and in some cases even the -25 µm class. Bowl geometry (angle) and gangue size distribution were the most significant operating variables. Results with the massive sulphide ore were the poorest, with gold recoveries typically around 10 to 20% at very low upgrading ratios, 1: 1 to 5: I. Gold recovery from the fine flotation tail ranged from 30 to 70% at upgrading ratios of 5 to 15; actual plant application would require a continuous unit (Falcon C20). The high grade gold cyclone overflow yielded a wide range of gold recoveries, but a very consistent relationship between recovery and mass processed. A concentrate of 0.5% Au could be processed at a recovery of 50%.The paper also presents results of a C20 application to recover fine iron from a magnetic tail. The unit is capable of recovering approximately 70% of the fine liberated iron in a high density product, with modest upgrading below 105 µm, and virtually complete rejection of the + 300 µ m product."

Jan 1, 1993

By E. Milke, A. Arnold, B. Friedrich, A. Sydykov

CaF2is often used as a fluoride addition to the chloride salt flux in the melting of aluminium scrap. The solubility of CaF2in the chloride salt system is limited. Dissolved CaF2is considered to improve the properties of salt fluxes. Experimental investigations indicated that the solubility ofCaF2in 70 wt % NaCl/30 wt % KCl, German salt flux used in aluminium scrap melting, might be lower than expected according to literature data. The pseudo binary section CaF2-(70 wt % NaCl-30 wt % KCl) was investigated by differential thermal analysis (DTA). The determined solubility of CaF2appeared to be considerably lower than presented in the literature. The pseudo binary section calculated using thermodynamic data partially confirmed the results. DTA allowed us alsoto determine the crystallization temperature interval of the two phase eutectic consisting of the solid solution NaCl-KCl and CaF2. Keywords: aluminium recycling, phase system, salt flux, CaF2, NaCl, KCl, solubility

Jan 1, 2004

By Gunnar Persson

The borehole pressure/time history of blasting practice is simulated in a twin pendulum apparatus, where the expanding shotfiring gases force two steel slab swingers apart. A pilot installation built at SveDeFo is described. The relevant factors, that govern the use of this test method as a means of classifying explosives with respect to their toxic fume potential, are described.

Jan 1, 1996

By S. McAlister

"Falcon Concentrators Inc. has developed a high capacity centrifuge for the recovery of fine, free gold as well as other metals and minerals which were previously thought to be unrecoverable by gravity means. Development started in the early 1980's and the first commercial operation was commissioned in 1986. Gold applications include scavenging conventional gravity and cyanidation circuit tailings, cleaning gravity concentrates, cleaning flotation concentrates to melting grade, scavenging flotation tailings, and placer mining. Recent development work by Falcon has expanded the applications scope of the centrifugal concentrator to include many minerals amenable to gravity concentration including iron, tin, industrial minerals, and hazardous wastes. This paper discusses this technology including its history, present applications, and future potential. OVERVIEW OF CENTRIFIJGAL CONCENTRATIONUsing centrifugal force to enhance the separation of materials by differential specific gravity has been researched for over a century. Many attempts have been made to concentrate minerals in high gravity fields. Patents were granted on this subject as early as 1891 (see Figure 1). Patenting activity continued into the 1920's and has been relatively quiet since. It is significant that no centrifugal system of gravity concentration has been broadly accepted by the mineral processing community until recently. Much of the world's reserve of mineral deposits which are amenable to conventional gravity concentration technology (coarse-grained) have been mined and therefore there is an increasing demand for technology which can economically recover the fine-grained gravity recoverable minerals in the remaining deposits. In addition, centrifugal concentration can play an increasing role in solving environmental problems by offering an inexpensive method of concentrating hazardous materials such as uranium, plutonium, mercury, lead, and other heavy metals. The overall cost of disposing of these substances safely can be drastically reduced if they are recovered into a concentrated form prior to disposal."

Jan 1, 1992

By K. Awuah-Offei

Long-term production scheduling optimization has been a challenging issue for the mining industry because of the size and complexity of the problem. The current planning algorithms have limitations in terms of addressing the stochastic variables underlying the mine planning problem. In this paper, an intelligent agent-based mine planning framework based on reinforcement learning is introduced. The long-term mine planning is modelled as a dynamic decision network. The intelligent agent interacts with the block model by means of a stochastic simulation and employs a Q-learning algorithm to learn the sequence of pushbacks that maximizes the net present value of the mining operation. The intelligent open pit simulator (IOPS) was implemented with an object-oriented design in Java®. A comparative application case study was carried out to verify and validate the models. The proposed method was used in planning an iron ore deposit and the results were compared to the Milawa scheduler used in Whittle® software. The outcome of the study demonstrates that the intelligent agent framework provides a powerful basis for addressing real-size open pit mine planning problems.

Jan 1, 2008

By T M. El Hajj, A C. Chieregati, M T. G C Marques, J M. Braga Jr, H Delboni Jr

"The estimate and control of sampling errors is essential for all mining operations, especially when dealing with strategic materials, such as niobium. This paper is based on a traditional quality assurance and quality control technique used to confirm mineralised intersection zones, and proposes the validation of sampling data using diamond drill twin holes, in order to evaluate and improve the quality of the current data set. The geological model of the niobium mine – located in Araxá, Minas Gerais, Brazil – was built including 77 diamond drill holes of a sampling campaign carried out during the 1970s. There are few records about the collection and preparation procedures of these past samples, making it difficult to estimate the errors associated with their analytical results. Therefore, 11 twin drill holes were drilled to compare their samples against the samples from the 1970s drilling campaign. The new hole locations were chosen as near as possible to the old holes location. The JORC Code, 2012 edition, relates the use of twin holes as a good sampling technique to assess sampling and assay data. Three parameters were considered to validate the 1970s drill hole campaign by the twin drill hole campaign: the difference of the coordinates between the paired holes the difference among the positions of the geological contacts to validate the geologic description the difference between the paired samples grades was calculated to validate the analytical results.The analysis of the grade range variation between sample pairs was based on three techniques: geostatistical interpretation of vertical semivariogram to obtain the nugget effect calculation of the relative difference between duplicates calculation of the error associated with the sampling protocol established according to Pierre Gy’s Theory of Sampling.The results were satisfactory for hole coordinates; however, the ore content showed a high deviation, although this divergence can be explained by the nugget effect. For the lithological intervals, the new results contributed to an effective identification of variations among lithologies, ie brown weathered ore and saprolite. The twin drill holes campaign successfully validated the geological model data, allowing effective mine planning and higher reliability of the reconciliation results.CITATION:Marques, M T G C, El Hajj, T M, Braga Jr, J M, Chieregati, A C and Delboni Jr, H, 2017. Theory of Sampling and geostatistics for twin drill holes analysis in a niobium mine in Araxá, Brazil, Australia, in Proceedings Eighth World Conference on Sampling and Blending, pp 97–106 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

Incorrect sampling and measurement operations and misunderstanding the components of variability can cause huge economic losses to the mining industry. The main objective of this paper is to illustrate by means of four historical facts how Codelco has been evolving in those issues since the late 1980s. The El Abra bias, the awareness of the different kind of sampling errors and the role of Francis Pitard, the awareness of weighting errors, and the understanding of the components of nature and process variability are described. It has been a slow but a consistent process. Much progress has been achieved but still there are many opportunities for improvement to transit from the tonnage culture to the productivity culture.

Jan 1, 2008

By T. Belem

The main objective of this study is to better understand the effect of underground CPB placement conditions on its microstructural, hydro-mechanical and geochemical properties. To reach this objective, three PVC columns, each 3 m high, were built, and were filled with CPB material. The columns allow simulating undrained (UD), half-drained (HD) and fully-drained (FD) conditions along with the measurement of resulting self-weight consolidation settlement of the CPB. Bleed and drainage waters were also collected from each column for geochemical analyses (pH, Eh, EC, SO42- content). After 90-days of curing time, a total of sixty CPB samples were cored from the backfill columns and subjected to uniaxial compression tests followed by physical characterization (Gs, void ratio, water content, degree of saturation, specific surface area). The results showed that the total drainage water and the maximum observed settlement occur mainly within the first 72 hours after the columns are filled. The corresponding volumetric strains suggest that in situ backfilled stopes simulated behave in a similar way to the fully-drained (FD) or the half-drained (HD) conditions. The MIP test results show that the pore structure varies between the top and the bottom of each column.

May 1, 2007

Sustainable development is a critical discussion topic in the mining industry today. The topic is necessarily broad and complex, covering an entire spectrum of related areas, from geology to end-use products. The objective of this keynote address is to focus on the chemicals and chemistry aspects - especially research and technology transfer - in sustainable mineral processing. Chemicals came to play a critical role in mineral processing during the last century, and they will play an equally vital role in confronting the sustainability challenges of the 21st century, particularly in the areas of greener chemicals, water efficiency and water resource management; waste reduction and remediation; minimising environmental impact, safety and health risks (meeting and exceeding the requirements of regulations); energy efficiency; and converting mineral resources into reserves. This keynote address argues that the current research framework is no longer adequate to serve the goals of sustainable mineral processing. The problems studied are often too narrowly defined or irrelevant, while the research efforts are fragmented and the methods and approach employed are often too reductionistic to produce useful knowledge. A new framework for research is needed. This address further argues that a new framework based on a holistic or systems approach can best tackle the challenges of sustainable mineral processing. Central tenets of this approach include a recognition that, in complex systems, the behaviour of the whole system is more than the sum of the individual contributions, and that interactions occur in real time, often in subtle and complex ways. The focus is thus on the behaviour of the whole system. Indeed, a comprehensive understanding of the system through large-scale measurements should precede a study of parts or of idealised models of the complex system. The result will be a sound knowledgebase, better solutions to the challenges of sustainable development, and improved technology transfer. Developing such a framework will pose a formidable challenge, requiring significant time and effort as well as a confluence of diverse specialties and strategic collaboration. Fortunately, recent developments in the context of reagent optimisation provide us with a prototype of a holistic approach. We can also draw upon methodological innovations in the biological sciences, where the critical need for a systems approach is well recognised and significant advances have been made.

Sep 13, 2010

By Andrukaitis. E.

The increasing use of electronic equipment by the Canadian Forces has increased the importance of electric power. A power source that is packed with energy and yet light, small and durable is the common request of military users. However, this needs to be achieved while also addressing the requirements of safety, reliability and low temperature performance. The potential use of fuel cells in a military environment has become a possibility in several areas in the 21st century. Some examples of power source requirements and the materials related R&D required to give better, higher energy power systems in the future will be discussed.

Jan 1, 2005

By Sean Harvey

One of the manifestations of the dynamically induced failures in deep coal mines is the violent ejection of coal from the ribs. A possible protection against such failures is the use of a specifically designed dynamic support system with reinforcement units having the sufficient capacity to absorb the kinetic energy of the dynamic failure and a skin support that can adequately contain the disintegrated coal. With this method of mitigation in mind, a recently introduced yielding rock bolt, trade name Roofex, has been identified (Harvey and Ozbay, 2009) as a possible energy absorbing component of a dynamic support system. According to the manufacturer?s specification, the Roofex bolts can yield 300 mm (or more) displacement while holding 80 kN pull load. In order to assess the performance of this support unit in coal ribs, a series of in situ pull tests performed in two coal mines in Colorado. The results show that, under conventional pull test loading conditions, Roofex yielding bolts perform very close to their claimed specifications, thus showing a potential for their use as the main energy absorbing component of a dynamic support system. Further studies are required to confirm the in situ performance of these bolts under dynamic loading conditions and also to develop a containment component for a dynamic support system for the mitigation of dynamic coal rib failures.

Jan 1, 2009

By R A. M Maddever, P Jeanneau, V Flahaut

Over the entire life cycle of a mine, from early resource evaluation to the blasting of benches, the collection of geochemical data is crucial for the site operator, who must routinely and intensively drill and sample the orebody. This produces huge numbers of physical samples, in turn requiring significant cost and time for their preparation and assay. Moreover, despite best efforts, the sample recovery process is prone to error, which limits the quality of data.The pulsed neutron gamma technique has been used for decades in various industries, in particular oil logging, for its ability to provide direct identification and quantification of elemental concentrations. However, its implementation in logging tools for the mining sector is relatively recent. Built around the latest in technology for optimal spectrometric measurement, a commercial tool referred to as FastGrade™ 100 has been available for a few years and used with increasing success in the mining environment, specifically the iron ore industry, resulting in a reduction in the amount of collected samples. Relying on the physics of neutrons and gamma photons, both of which are particles that penetrate the surrounding bedrock through several tens of centimetres, such spectroscopy tools measure in real-time the composition of a much larger volume than the delimited volume of the drilled material traditionally used for geochemical mapping. Better statistics and reliability of the estimated composition increase the ability to properly and quickly measure drilled holes and allow the substituting of all or part of the sampling and assaying efforts by geochemical log data. Our paper focuses on this technology, known as pulsed fast and thermal neutron analysis (PFTNA). It reviews the main drivers for the design of such a logging tool and discusses how the fundamental characteristics of the technology, in terms of neutrons and gamma interactions, translate into interpretation of the analytical output.CITATION:Jeanneau, P, Flahaut, V and Maddever, R A M, 2017. Iron ore benefits from neutron pulsed geochemical tools, in Proceedings Iron Ore 2017, pp 387–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

U.S. Borax’s mine in California’s Mojave Desert is the source of nearly half the world’s supply of refined borates. These minerals are used in hundreds of products, including essential plant nutrients that increase crop yield and quality, and safe building products that protect homes from insects and the elements. Borax’s workforce is also safe. In fact, it is among the safest in the nation. In 2003, the company was recognized by the U.S. Mine, Safety and Health Administration (MSHA) for achieving the best safety record among large U.S. mining operations. It was also recognized by its parent company, Rio Tinto, for achieving the best record among its nearly 80 worldwide mining operations. Borax’s safety performance is five times better than the national average. And its workforce recently achieved more than two million hours without a lost-time injury.

Jan 1, 2004

An understanding of the way that solutes are transported in mining or natural environments is essential to the development of sound strategies for managing waste disposal. Research on miscible pollutant movement in unsaturated porous media is carried out both experimentally and numerically. Results of numerical modelling are obtained by solving the groundwater flow equation and the solute transport equation. The finite element method is employed and comparisons between simulation results and experimental data are found in remarkable agreement.

Jan 1, 1995

By A. D. Thomas

Some years ago, the authors developed an analysis of non-Newtonian pipe flow based on enhanced turbulent microscale and associated sublayer thickening. This analysis, which can be used for various rheologic modelling equations, has in the past been applied to smooth-walled pipes. The present paper extends the analysis to rough walls, using the popular Bingham plastic equation as a representative rheological behaviour in order to prepare friction-factor plots for comparison with measured results. The conditions for laminar-turbulent transition for both smooth and rough walls are also considered, and comparisons are made with earlier correlations and with experimental data.

Jan 1, 2007

By C. Birch

"A ‘geologically constrained’ orebody model has long been hailed as vital for a Mineral Resource statement that is compliant with the South African Code for Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code). In this paper, the requirements for geological modelling as contained in the outline for the SAMREC Code are considered, and whether the new modelling software available on the market is a ‘black box’ or is better for modelling than traditional methods of wireframe creation.Implicit geological modelling is a technique that uses a radial basis function to establish and update geological models relatively quickly and efficiently from borehole data, outcrop data, manually interpreted vertical or horizontal sections, and structural data. Assays and any coded drill-hole data, such as lithology and alteration, can be interpolated.Leapfrog Geo software is an example of this new approach to geological modelling. A case study of a short training course in geological modelling for non-geologists at the University of Witwatersrand, as part of the Higher Certificate in Mineral Resource Management, is presented. The benefits of this type of geological modelling software are considered for this type of assignment as well as for mining industry applications.The use of geological models in mine planning is reviewed and a case study is presented comparing the variations in mine plan design and financial output of 13 final-year Mine Design projects from the University of the Witwatersrand School of Mining Engineering. These designs were all based on the same geological model created in the traditional way, and yet the resultant mine designs were significantly different, with very different resulting financial outlooks for the project. This raises questions as to how significant a very detailed model in the pre-feasibility and feasibility phases of projects really is, considering the huge costs involved in gathering the required data to build a SAMREC-compliant geological model."

Jan 1, 2014