Search Documents

By Ling Wu

The development of pyrometallurgical technologies has been focused on new smelting reactors, but the proposal for new converting reactors has been substantially lower. Up to today about 80% of copper matte is treated by the traditional P-S converters which have the weakness of pollutant fugitive emissions. Therefore, the continuously converting processes for treating molten matte have been studied and developed. In July 2017 the "oxygen-rich side blowing smelting + multi-lances top converting & fire refining" continuous copper treating process was commissioned. This process was designed by ENFI and YanTai GuoRun Copper Smelter. In this process, oxygen rich side blow technology is adopted for smelting, which is a new type of side blowing smelting furnace to produce high-grade copper matte. The converting adopts the horizontal multi-lances top-blowing continuously converting process, which eliminates the transportation of molten melt and the SO2 fugitive emission. The intermediate products of this process, copper matte and blister copper is fed into the furnaces respectively through launders. This new process is more advanced, more reliable and more environmentally friendly. Until now, this process in the GuoRun copper smelter is operating smoothly. An increasing number of projects which use this process are under design and construction in China. INTRODUCTION At present, there are many advanced smelting technologies for copper concentrate, such as oxygen bottom blowing smelting, flash smelting, top lance smelting (including ISA and Ausmelt furnaces smelting), side blowing smelting, Mitsubishi smelting, etc. At the same time, there are many copper matte converting technologies such as oxygen bottom blowing continuous converting, flash converting, Ausmelt top lance converting, horizontal multi-lances top blowing converting, Mitsubishi converting, P-S converter converting, etc. The final blister copper fire refining technology mostly adopts rotary anode furnace. Therefore, in the process of processing and extracting the copper from concentrate to produce anodes, there are dozens of technology combinations. Among them, the non-continuous converting technologies for molten or cold matte are often adopted in the converting process. The traditional P-S converting technology had been utilized for over one hundred years, with a mature, reliable and simple operation, also has advantages in the secondary scrap smelting of a wide range of quality. However, due to its batch operation, frequent roll in and out, poor sealing, considerable air infiltration, needs for ladles for molten phases transportation and other characteristics, the technology has a serious pollution problem due to fugitive SO2. At the same time, in the cold matte converting technology, the molten matte needs to be cooled and then processed. The sensible heat of the molten matte cannot be recovered, and the preparation process is needed in the process. Therefore, both energy consumption and investment are relatively higher.

Jan 1, 2019

By M. H. Forester

The Bituminous Coal Industry has for the past year been faced with a most serious problem. I am sure that you have had your own individual and local problems, as do we all. In my thirty years of practical experience with coal mining, I have never found an operating man nor a coal mine without problems. The very nature of mining, with so many unknown factors involved, precludes the absence of problems. But they are not insurmountable, and one should not dwell on them interminably. They should be recognized as a challenge to our ability and ingenuity to solve them, and once the proper solution is found, it should be applied and the problem dismissed. However, we find ourselves at the moment in the midst of a serious challenge to our very existence. In the early thirties, many in the industry welcomed the re-establishment of Unionism as a balance wheel, in the belief that the stabilization of wage scales would also stabilize prices and eliminate disastrous price cutting practices. The ultimate effects of having twenty-six years of benevolent paternalism in the administrative branches of Federal and State Governments with their labor courting policies, could hardly have been anticipated. And so with wages spiralling under government sponsorship, we have finally reached the point where competitive fuels, such as natural gas and oil are more attractive to the consumer, from the economic angle of cents per BTU cost, than coal.

Jan 1, 1953

Case 1: A driller raised a drill rig mast into a 7200-volt overhead power line. Both he and his helper were killed. Case 2: A driller-helper was pulling a winch cable toward a stack of drill steel when the cable contacted a 12,000-volt power line. The helper was killed, and the driller at the rig controls was severely injured. [ ]

Jan 1, 2006

By C Dick

Over the past three decades, mining operations have seen a significant increase in the use of contractors for mining, camp management and catering, recruitment, maintenance, power management, and commissioning. More recently contractors have been engaged for stores and logistics, OH&S, environmental, exploration, training etc. In some countries, such as South Africa, the trend is towards total outsourcing of all aspects of a mining operation which is coordinated by the owners’ management team.During the Global Financial Crisis (GFC) more Australian companies considered and/or took on this approach to recruiting for both projects and operations as mining companies were forced to rethink their corporate strategies as commodity prices plummeted to low levels, pushing operations and projects into potentially financially unviable territory.This paper discusses the labour recruitment, commissioning and operating strategy of Western Areas NL (WSA), with the assistance of Independent Metallurgical Operations Pty Ltd (IMO), as it progressed construction, commissioning and operation of the Cosmic Boy nickel concentrator at the Forrestania Nickel Project during and post GFC. The use of IMO contractors allowed Western Areas to mitigate labour cost risk during the uncertainty caused by the GFC and let their management team focus on the task of bringing a new operation into viable and profitable production.

Aug 8, 2011

By M. Kozlowski, I. Candy, S. Kashani-Nejad

The production of ferronickel and matte from nickel laterite ores is dominated by the Rotary Kiln, Electric Furnace (RKEF) process. Over time, major improvements have been made to kiln operation. In particular, kilns are now required to perform substantial amounts of reduction of the metallic oxides, thereby reducing the load on the electric furnace and substituting less expensive fossil fuel for electrical energy. To the basic refractory lined cylinder have been added: internal features such as dams and lifters, aimed at changing residence times in different sections of the kiln and enhancing gas/solids interaction, on-board fans to introduce tertiary air and on-board scoop mechanisms to allow reductant coal additions to be made at advantageous locations along the kiln. Many of these advances in design have been made on a trial and error basis and by 'borrowing' technology from related kiln processes, supplemented by proprietary modeling to various levels of sophistication. This paper presents a conceptual review of modeling components for the development of a computational model for granular material flow, combustion and heat and mass transfer in a nickel laterite kiln. These components include: granular material flow and segregation models for the simulation of bed motion, heat transfer models that simulate heat transfer by turbulent diffusion and radiation and the distribution of this thermal energy within the bed, and fluid flow models for the prediction of combustion aerodynamics.

Jan 1, 2005

Fossil resin types occurring in the Hiawatha seam of the Wasatch Plateau coal field, Utah, have been separated according to color and their physical and chemical properties evaluated. These resin types were separated into four color fractions, yellow, amber, light brown, and dark brown. Each resin type has then been subjected to comprehensive spectroscopic examination and other physical methods of characterization. Included among the spectroscopic methods of characterization are FTIR and 13C NMR spectroscopy. Physical properties that have been measured include density, optical, and magnetic properties. These analyses reveal that the resins are distinct from other macerals, predominantly nonaromatic in nature with small amounts of oxygen functionalities and a low degree of unsaturation. The four resin types show distinct differences in certain physical and chemical properties such as density, hexane solubility, magnetic susceptibility, and aromaticity.

Jan 1, 1990

By H. F. Yancey

Although a general relationship exists between the two criteria used to measure sharpness of separation -error area and probable error -they sometimes give quite different appraisals of a particular washing operation. Error area takes into account how the entire raw coal was treated, whereas probable error reflects only how the material of intermediate density was separated, ignoring completely the recovery of clean coal and the rejection of heavy impurity. Error area is thus more reliable for general use. In heavy-medium cleaning, sharpness of separation decreases with increase in separating density, but ordinarily the change is not great enough to affect the yield and ash content of washed coal measurably. Therefore, distribution curves for heavy-medium units can be transposed from one separating density to another, at least in the range of separating densities ordinarily used in the United States.

Jan 1, 1955

By P. J. G. du Toit

Coal has been mined by hydraulic means in various countries, i.e., the hydraulic excavation as well as the hydraulic transportation of coal has been practiced. The hydraulic breaking (excavating) of the coal dealt with in this report is done with a monitor directing a continuous jet of water against the coal, pressures of the water fed to the monitor range from 1500 to 2500 psi at 1000 to 2100 gallons per minute Transportation of the coal from the face is by fluming if a gradient exists in excess of 2 or, when a favorable gradient does not exist, the coal is pumped from the face by various types of pumps which can also provide a means of hoisting the coal to a higher elevation as required. This report presents: 1.) preliminary design and systems specifications of a demonstration miner (referred to in this report as a hydrominer), 2.) mining configurations showing good promise for typical U.S. thick coal seams in three seam pitch categories, (0° - 7° = Flat, 8° - 250 = Moderately pitching, 26° - 90° = Steeply pitching), along with cost and performance analyses for each system, 3.) a definition of a test program that will provide sufficient engineering data for the design of a water jet cutting head adequate to cut coal in those typical U.S. thick coal seams The cost analysis data showed hydraulic methods to be economically competitive with present thick seam raining methods. It was also obvious from studies of thick seam methods that the hydromonitor coal breaking techniques are more effective in removing most of the coal with its long reach of 60 ft. (or more), is a safer mining system, and produces very low coal-dust content in the air (usually less than 0.25 to 0.5 mg/cubic meter). It is recommended that the USBM sponsor a full fledged continuation of the hydraulic mining program: (a) lab, test, (b) preliminary field test, (c) full scale mine section demonstration.

Jan 1, 1977

By Manuel Gomez

A lignite from Milam County, Tex., has been oxidized by air at temperatures from about 27° to 300° C. for varying lengths of time. The oxidized coal was carbonized at 500° C. in a laboratory assay unit, and the products of carbonization were measured and analyzed. The data presented suggest that, as lignite is progressively oxidized, tar yields are decreased and gas yields are increased in a ratio approximating 1:1. It is surmised that tar-yielding structures in the nonoxidized coal produce gas, principally, when the coal is oxidized. Char-yielding structures of the nonoxidized coal give rise to additional water of decomposition after oxidation and pyrolysis. As lignite is subjected to greater oxidation, the gaseous product evolved on pyrolysis becomes almost entirely carbon dioxide. Tar yields decrease with an increased degree of oxidation, so that the reduction in tar yield may be used as a qualitative measure of oxidation. Pilot-plant drying and carbonization, where air is used as the transport gas and where some air is included in the drying and carbonizing gases, induces some oxidation of the coal particle. The short residence time in a fluidized system with reference to the oxidation environment limits the oxidation.

Jan 1, 1956

By Aditya Ayithi, William G. Ryan, Dean Herbst

"For rock socketed drilled shafts, it is a common practice not to include the frictional resistance of overburden soils into the nominal capacity estimation. The primary reason often being cited is “overburden soils resistance is negligible compared to that of rock socket resistance.” However, in certain geological conditions, where the rock layer is located at greater depths, friction resistance from overburden layers can be significant. In addition, at such great depths, shaft drilling becomes very complicated and expensive. In these situations, considering the resistance of the overburden layers can be an economic alternative.This paper presents a case study of an Osterberg cell (O-cell) load test conducted on a 161.8 feet long and 78-inch diameter instrumented test shaft. Based on initial designs, a 72-inch diameter rock socket of lengths 23 and 26 feet was required to provide a LRFD factored friction resistance of 3,200 kips. The load test results revealed that the material in the 72-inch diameter socket does not represent a true rock. However, the test results also proved that the factored friction resistance of overburden layers is greater than the required design resistance. Based on the load test results, it was decided to allow the overburden soils frictional resistance to be considered in the shaft design, resulting in significant economic savings.INTRODUCTIONRock socketed drill shaft design guidelines of various State Department of Transportation (DOTs) agencies allow friction and/or end bearing resistance of only the rock socket portion into the design capacity estimation. It is typical to neglect the frictional resistance of overburden soils. However, in certain geological conditions where the rock layer is at greater depths, friction resistance of the overburden soils can be significant. In this case the friction resistance of overburden soils was verified via the specified instrumented O-cell test program and then used as part of the design capacity.PROJECT DESCRIPTIONAs part of I-29 improvement project, Iowa Department of Transportation (Iowa DOT) planned to replace the dual four lane bridges that cross the Floyd River in Sioux City, Iowa with dual six lane bridges (Fig. 1). Expected benefits from this improvement include improved safety, traffic operations and roadway infrastructure conditions.BRIDGE SUBSTRUCTUREThe project consists of two individual bridges; a new south bound bridge and a new north bound bridge. The south bound bridge is 646-ft long and the north bound bridge is 644-ft long. Both are six-span, pretensioned and pre-stressed concrete beam bridges of varying width. Bridge foundations were designed such that the abutments of both bridges will be supported on driven steel piles and the bridge piers will be on drilled shaft foundations."

Jan 1, 2016

By Richard D. Luark, Fernanda S. Madrona

Designing temporary retaining systems that allow for deeper excavation amid the existing urban infrastructure has become a challenge. A 60-foot-deep excavation in downtown Seattle was required to construct five levels of below grade parking for a 35-story high-rise building, Tower 12, next to an existing 20-story tower with three levels of below grade parking, separated from the project by an 18-foot wide alley. The solution was to combine two temporary excavation support systems, soil nailing and anchored soldier piles, to work within the site constraints. Densely-arranged, short-length soil nails were used to support the upper 30 feet of the excavation, while the lower 30 feet of the excavation was supported with soldier piles combined with steeply-inclined, high-capacity ground anchors, which extended below the adjacent building foundations. The combined temporary support system eliminated the need for internal bracing, reducing construction cost and schedule. The performance of the combined soil nail and soldier pile system was monitored with an inclinometer and optical survey monitoring, which demonstrated the performance of the combined temporary support system. This paper provides a discussion of the advantages of combining different excavation systems and an analysis of movement monitoring data collected. SITE CONDITIONS AND PROJECT INFORMATION Tower 12 consists of a 0.45-acre development with 36-stories of mixed, residential and commercial use with four levels of below grade parking. The project site is bounded by the Cristalla Condominium to the north, Virginia street to the south, 2nd Avenue to the East, and an 18-foot wide private alley to the west. The One Pacific Tower Condominium, which has three levels of below grade parking, was located to the west across the alley. A site layout plan is presented as Figure 1. As shown in Figure 1, the construction of the west wall required a maximum 51-foot-deep excavation, from elevation (EL) 162 feet to EL 111 feet. Adjacent to the west wall, the existing alley grade varies from elevation 154 to 161 feet, leaving a narrow block of soil 18 feet wide and up to 42 feet high to be shored along the alley in order to reach the One Pacific Tower bottom of mat foundation at EL of about 120 feet. In addition to the existing One Pacific Tower Basement wall, site constraints included existing utilities along the alley such as an existing 4.5-feet wide by 7-feet high vault, with bottom at approximate EL 146 located 10 feet from the back face of the proposed Tower 12 basement wall.

Jan 1, 2019

By H. C. Gunning

SOME small vanadium-bearing deposits on the west coast of British Columbia about 100 miles north of Vancouver are of interest for several reasons. They are of a type that is, so far as we know, unique. They are difficult to identify as being vanadiferous so that, unless they are described, other similar deposits could easily pass unrecognized. Furthermore, although none of them has as yet been proven to be of commercial proportions, no good reason is apparent why larger, and therefore valuable, deposits should not occur under similar geological conditions. The original discovery on Quadra island was made in 1932 and has been recorded by H. V. Ellsworth and H. C. Gunning (l). Since 1932, prospecting in the area has revealed other similar deposits, one about a mile south of the original and another some ten miles to the east, near Menzies bay on Vancouver island. The Quadra Island showings are a mile and a half north of the head of Gowland harbour, a small inlet that is easily reached by gas boat from Campbell river, about four miles to the southeast on Vancouver island. The deposits were examined by the writers in the spring of 1943 in connection with field work sponsored by the Department of Geology, University of British Columbia. We are indebted to Mr. G. A. Dirom and Mr. Lothrop, of Vancouver, for helpful data on the Menzies Bay deposits, and to Dr. V. Dolmage for making a brief trip to Gowland harbour and discussing the deposits.

Jan 1, 1944

By N Yarahmadi

Characterization of pore pressure is critical for appropriate design of tailings dams. Furthermore, if seepage rates through tailing embankments increase unexpectedly or become uncontrolled, undesirable conditions may prevail to progress piping or internal erosion that could lead to the dam’s instability or ultimate failure. A three-dimensional seepage analysis was performed on a tailings dam using finite element method to find the rate of seepage and pore water conditions in the embankment and foundation. The results were then compared to a conventional two-dimensional seepage analysis carried out on the typical cross section of the embankment and the field data acquired from the instrumentation system. Considering the monitoring data, comparison of seepage analyses results for the two and threedimensional models, showed that the results of the conventional two-dimensional seepage analysis are significantly underestimating reality. Relying on two-dimensional seepage analyses might result in underestimation of seepage rates and impact the safe operation of tailings dams. Similarly, unrealistic prediction of pore water pressure conditions, based on simplified seepage analyses, can lead to overestimation of the rate of strength gain of material and consequently safe embankment raising rates.

Jul 1, 2021

By Henry P. Wheeler

As recently as 1915, helium was available only in very small quantities at a cost equivalent to $2,500 per cubic foot. It was a laboratory curiocity, and its properties were of interest to a limited number of scientists (11).3/ During the past 30 years, however, helium has grown from a plaything of scientists to a factor of importance in the prosecution of the recent war. Navy blimps filled with nonflammable helium proved to be more than a match for German submarines operating in the Atlantic. American bombers were able to fly unheard-of distances to drop bombs on Tokyo, Nagoya, Yokahama, and other Japanese cities because they had been made lighter with magnesium, arc-welded in a helium atmosphere. The Army utilized helium-filled radio-sonde balloons to obtain vital information concerning weather conditions affecting D-day invasions and other military maneuvers.

Jan 1, 1946

By T J. Sullivan, H Pinkster, G Swarbrick

From 2002 to 2006, longwall mining was undertaken directly beneath the Cataract Tunnel, which is a 100-year-old, heritage-listed tunnel in Hawkesbury Sandstone responsible for delivering 20 per cent of Sydney’s annual water supply. At one location, undermining resulted in movement of at least 350 mm along a known fault that transects the tunnel. During this movement, the continued operation of the tunnel was ensured through a careful system of planning, monitoring and management.Of key importance to the success of the operation was the use of advanced numerical modelling to guide operations at all levels, including feasibility assessment, pre-mine mitigation works, monitoring design, operation performance and post-mining condition. This allowed many aspects of the potential impacts to be explored, including joint movements, rock mass deformations and changes in permeability. A key challenge was to successfully model near-field influences on adverse geological structure due to very far-field effects. This paper explains the model’s conceptual development, calibration, performance and limitations.Modelling provided the confidence to manage the impacts of large mining-induced movement on key infrastructure and ultimately predicted fault movement accurately. The fault movement remains one of the highest ever recorded due to mine subsidence.CITATION:Swarbrick, G, Sullivan, T J and Pinkster, H, 2014. Longwall mining beneath critical infrastructure – prediction versus performance of the Cataract Tunnel, New South Wales, Australia, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 157–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By C. B. Davison

One goal of the Bureau of Mines is to conserve the Nation's mineral resources by developing improved performance materials. Consistent with this goal, the Bureau conducted studies on the formation of undesirable cristobalite in seven different fire clays used as refractories. The studies employed scanning electron micrography, chemical and X-ray analyses, and pyrometric cone equivalent determinations to examine the sample clays and determine the effect of thermal history and stablilizing additives on the amount of cristobalite in various calcines. This research has indicated that as fire clay calcining temperatures increased from 1390° to 1,490° C there was a gradual decrease in the percent of cristobalite present in the calcines and a progressive development of mullite crystallization. No cristobalite was found in fire clays calcined above 1,550° C, but cristobalite reappeared when the calcines were reheated to temperatures between 1,400° and 1,500° C. The research also revealed that additions of lithium fluoride (LiF) prevented formation of cristobalite in fire clay calcines.

Jan 1, 1979

By G. G. Oberfell

THOUGH the largest volume use of natural gas has been, is. and in all probability will continue to be as a fuel for domestic and industrial heating, it has various market outlets, both as a fuel and as a raw material for the chemical industry. Natural gas is a preferred type of fuel where ease of control, fuel uniformity, and freedom from ash are of primary importance. Other industrially important uses are as a source of carbon black and as a fuel in various low-cost heating operations. Many other uses are of varying importance and new potential uses are continually being uncovered, some being of economic importance to the gas indus¬try as a whole, but most of them involve such small volumes of gas that they are only of passing interest. Since various products extracted from natural gas and recovered as by-products from petroleum refining, such as liquefied petroleum gas and fuel oil, are being utilized in many industrial and domestic heating applications, some consideration will have to be given such materials in order to present a reasonably complete story of the importance of natural gas. Some of these materials may prove to be transient competitors and will not be available when more profitable uses are found for them. Meanwhile, however, the potential volumes of such materials available, the current volumes being marketed, and the nature of the utilization are considered as constituting an essential part of the over-all fuel picture.

Jan 1, 1946

By S. Mafi

The Broken Aro project is associated with a 1910 abandoned underground mine complex that has been discharging aeid mine drainage from entries, seeps and springs. The Ohio Department of Natural Resources(ODNR), R&F Coal Company (R&F) and American Electric Power (AEP) are involved with this unique project that will remine the abandoned underground complex and install a mine seal constructed of fixated flue gas desulfurization (FGD) material. The goal of the project is to eliminate or reduce the acid mine drainage that is discharging into the watershed. This paper discusses remining, installation of the FGD mine seal, government financed reclamation projects and future application to active and abandoned mining sites.

Jan 1, 1998

By Sheridan J. Rodgers

Toxic fumes generated during shot firing under actual mining conditions were measured. Eight shots with Gelodyn-2X and seven shots with Tovex-100 4VT were monitored. Average CO values for Gelodyn-2X and Tovex-100 4VT were 0.20 ft3/lb and 0.09 ft3/lb, respectively. Average N0x values for Gelodyn-2X and Tovex-100 4VT were 0.049 ft3/lb and 0.026 ft3/lb, respectively. The results obtained with these in-mine tests will be used by the U.S. Bureau of Mines in the development of a large chamber method of measuring fumes from shotfiring of explosives.

Jan 1, 1977

By Cody Giroux, Homer Scurlock, Michel Wasag

Silica and Crystalline Quartz exposure continues to be a serious health threat to nearly 2 million workers in the United States, including more than 100,000 working in high risk jobs such as abrasive blasting, foundry work, stonecutting, rock drilling, quarry work, mining and tunneling. The primary focus of this study is to identify the best methodology to reduce particulate-laden air and limit/eliminate exposure to respirable dust with silica/crystalline quartz during tunneling operations. This study focuses on two de-dusting systems employed on similar tunnel construction projects. The first project is the Coxwell Bypass Tunnel located in Toronto, Ontario Canada. The second project is the Westerly Storage Tunnel located in Cleveland, Ohio. The Toronto project is utilizing a wet de-dusting system. The Cleveland project is using a dry de-dusting system. The objective is to determine which system provides the best protection and suitability to capture, remove and ultimately reduce respirable concentrations of silica/ crystalline quartz to safety and healthy levels in underground tunneling activities.

Jun 13, 2021