Search Documents

By B K. Da, S A. Balaji, G P. Roy, T K. Dutta

The raw material handling complex at the Durgapur steel plant provides iron ore, crushed coke and flux to two sinter plants. Either some facilities were not envisaged or not properly designed before the project stage which caused problems during operation of the plant. The absence of an in situ roll turning facility, used to increase maintenance activities for disassembly, transportation of rolls to central machine shop and assembly of rolls, led to decreased crusher availability and increased activities for the maintenance crew. The provision of a smaller vibro feeder/screen in place of a suitable sized screen caused jamming of the screen deck, adversely affecting screening efficiency and the crushing index of crushed coke. Some design modifications and developmental work was undertaken, such as the development and installation of an in situ roll turning facility in the existing limited space, achieving low feed (0.1 - 0.2 mm/rev), lower cutting speed of 30 - 40 m/minute for 350 BHN hard roll, which was also a difficult engineering challenge to bring within the tolerable limit of vibration. This was successfully achieved. Modifications to the screen deck, introduction of differential speed crushing and modification to the vibro screen and vibro feeder for uniform distribution of feed have been incorporated. These innovative design modifications to the in situ roll turning have led to a drastic decrease in maintenance activities and an improvement in the crushing index. Modifications to the screen have resulted in the elimination of jamming and improved screening. Modifications to the vibro screen before the primary crushers and to the vibro feeder before the secondary crushers have prevented excessive wear in the central portion of rolls, ultimately leading to increased roll life. Incorporation of differential speed crushing has resulted in an increased crushing index and decreased generation of micro fines. All the above modifications have led to distinct improvements in equipment availability, increased roll life and a decrease in maintenance activities and improvement in crushed coke granulametry, ultimately resulting in improved productivity and quality of iron ore agglomeration at the sinter plant. The innovative design modifications mentioned above are discussed in detail in this paper.

Jan 1, 2005

Electrical trailing cables are frequently damaged in usage, especially on continuous minors, and because of their weight and damaged condition present a safety hazard to personnel required to handle them. The U.S. Bureau of Mines and FMC Corporation signed Contract No. HO 122011 in August 1971. One of the contract tasks was to study the feasibility of techniques to improve trailing cable support and handling of power cables on underground coal mine machinery and to design a cable-handling device for a continuous mining machine. This report presents the results of the feasibility study, describes the design for a proposed cable handling device and concludes with a recommendation for future action to construct a test rig to evaluate the cable reel system.

Jan 1, 1972

By Trevor R. Ellis

Minerals appraisers/valuers often find great difficulty in attempting to employ the sales comparison approach to the market value appraisal of development and operating stage mineral properties. An important factor generally overlooked is a comparison of net operating income (NOI) margins on a per-unit-of-production basis between mineral properties, whether these be demonstrated or forecast margins. NOI margins can vary greatly between mines or quarries that are producing similar products. Ultimately, the expected NOI margin determines what a buyer is willing to pay for an income-producing property. Here, common criticisms of the sales comparison approach by mineral appraisers are introduced. These are counterbalanced by raising some issues in the way the inputs for the income approach are usually derived by minerals appraisers and by review of some conspicuous examples of the much-too-common misuse or abuse of the income approach in market value mineral appraisals. Example transaction analyses and sales comparison analyses are used to demonstrate the author?s methodology for adjusting units of resource in his transaction adjustment tables. The examples are used as the basis for a discussion of ways to employ adjustments for operating economics and many other factors, while warning against the potential for double counting. The conclusions include a recommendation that minerals appraisers attempt to apply at least two of the three valuation approaches when appraising the market or fair value of development and operating stage mineral properties, the two being the sales comparison and income approaches.

Jan 1, 2011

By Nathan Feldstein

The wetting of coal dust by aqueous solutions of surface active agents (surfactants) has been studied. Selected for study were thirty coals and typical surfactants selected from the typical classes of anionic, non ionic and cationics. Of these three classes the practical use of cationics in aqueous solutions has been eliminated due to the inherent negative Zeta potential charge of the representative coals studied. The wetting of the coals has been examined by column flow, contact angle, and settling rate measurements. Results indicated that both anionic and nonionic surfactants are to be considered viable for use; low critical micelle concentration values are also preferred for the surfactants. Study of native waters showed substantial variation in properties, i.e., pH, calcium ion concentration, and conductance. pH variations were also noted to affect the effectiveness of selected surfactants. Combinations of nonionic and anionic surfactants have, in certain instances, produced synergistic enhancement in the coal wetting superior to the effectiveness of each surfactant alone.

Jan 1, 1981

By Forrest T. Moyer

Injury experience at metal mines and mills (excluding officeworkers) in 1964 was 60 fatal and 3,672 nonfatal disabling work injuries during an exposure time of 149 million man-hours worked. These injuries occurred at a frequency rate of 24.57 per million man-hours and had a severity rate of 3,687 days lost or charged per million man-hours. Employment at 2,363 metal mines and 291 mills, excluding officeworkers, was 68,140 men in 1964. The average number of days worked was 274 The principal cause of fatal injuries at all mines and mills was haulage accidents and in underground mines, only, was falls of ground. The principal cause of nonfatal injuries was handling material accidents. The frequency rate at metal mines and mills in 1964 was slightly below that of 1963, whereas the severity rate was higher. Injury experience at 94 primary nonferrous smelters, refineries, and reduction plants (excluding officeworkers) was 8 fatal and 999 nonfatal disabling work injuries during a worktime of 98 million man-hours worked. The combined injury-frequency rate in 1964 was 10.29 and the injury-severity rate was 1,005. The 36,956 employees worked an average of 329 days during 1964. The principal cause of injuries at these plants was handling material accidents.

Jan 1, 1968

By O. Rielo, P. Katsabanis

Traditionally fine aluminum is not used in dry commercial explosives due to the hazard associated with aluminum dust explosions during mixing. An industrial process has been developed which enables the safe use of paint grade Aluminum with ANFO. The addition of fine aluminum particles resulted in increased velocity of detonation of ANFO compositions. Velocities of detonation, in 52mm (2 1/16 in.) diameter confined charges were 20% higher than velocities of detonation of straight ANFO. The detonation performance of fine grained ANFO was not benefited by Al at the diameter tested. Furthermore use of larger Al flakes resulted in decreased velocities of detonation. The results are compatible with the experience of Al addition to high explosives. Tests were also conducted using bio-diesel, finding no substantial difference in the performance of AN fuel explosive compositions which used bio-diesel.

Jan 1, 2009

By Robert L. Morris

A new concept of roof support by "sonic pin-setting" is introduced. Initial experiments indicate that this method could introduce tremendous benefits for the coal mining industry by making roof-bolting a faster, safer, and more economical operation. A theoretical model is presented for describing the process and an experimental machine was built. The present testing results are included.

Jan 1, 1977

By K. Madhusudan Reddy

Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load?deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.

By A. Daugiala, D. Coleman

In 2014 the New York State Department of Transportation (NYSDOT) awarded a Design-Build contract to the joint venture team consisting of Skanska which is the managing partner; Kiewit Corporation and Ecco III (SKE) and HNTB as the lead design firm. The design build team employed methods to provide schedule savings and commercial benefits to the owner NYSDOT. This paper presents the design approach and construction methods used to accelerate drilled shaft installation supporting the main span foundation for the cable stayed bridge. The drilled foundation contractor Underpinning and Foundation Skanska, a division of Skanska was responsible for assisting with design, budgeting and construction of the drilled shaft foundation construction. As part of the Request for Proposal (RFP) bid process, Alternate Technical Concepts (ATC) was encouraged by the NYSDOT. The JV team proposed an ATC which involved a scaled production shaft testing method to simulate the ultimate load level, commonly referred to as the “Chicago Method” was used in the rock socket employing the Osterberg Cell (O-Cell) testing procedures. To the authors knowledge this was the first NYSDOT project where this approach was utilized on a Demonstration/Production installation to validate construction procedures and load bearing capacities. Construction procedures, challenges and solutions are discussed in detail. Upon completion of successful drilled shaft construction, concrete integrity is verified using two methods – Cross Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP). A comparison from the contractor’s perspective is provided. Finally the drilled shaft rock socket is tested to ultimate end bearing values while rock socket side shear stresses are not exceeding the service level loading. Lateral load test was also a RFP requirement; the test arrangement and performance are discussed in detail as well. The Kosciuszko Bridge location poised unique geotechnical challenges on many levels shifting towards an extreme boundary of parameters encountered in New York City Area for drilled shaft construction. The JV team and specialty drilled shaft contractor actively participating in the shaft design and construction practice coordination and working with NYSDOT yielded a successful foundation solution which provided cost and schedule savings to the project.

Jan 1, 2016

By John H. Johnson

White Pine Mine section designated for exhaust emissions studies. The MTU Mine Air Monitoring Laboratory was used to gather temperature and C02 concentration data at 10 locations. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in stratification in dead end headings. Diesel mine-vehicle tailpipe emissions were monitored in the laboratory by a portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. Diesel pollutant concentration data from the Orchard Valley Mine were analyzed and compared with data collected earlier in the White Pine and Brushy Creek mines. Lognormal frequency distributions and CO2-based concentration ratios and correlations were calculated. In the three mines compared, pollutant concentrations were distributed similarly, and concentrations appear to be controlled to present standards.

Jan 1, 1979

By Mark D. Fuhriman, Parham Khoshkbari, Robert Fosse

Drilled displacement piles are becoming an increasingly common deep foundation choice for their relatively simple installation methods, applicability to a wide range of subsurface conditions, and versatility. The installation method includes drilling and displacement of the soil followed by delivery of fluid cement grout under pressure, and placement of steel reinforcing to complete the pile. Because the installation method uses blind processes that do not permit direct observation of the pile, it is desirable to employ redundant testing tools to complement good construction techniques and inspection practices to ensure integrity of the piles. This paper examines the use of a range of integrity testing tools used for pile installations at a major office campus development. Because the integrity of a drilled displacement pile and its performance depend to a large extent on the skill and experience of the installation crew, the paper explores how use of multiple practical tools, including automated monitoring tools on the pile installation equipment, thermal integrity profiling, and high-strain dynamic testing, ensure structural integrity of the completed piles and how redundant integrity testing methods complement good construction and inspection practices add confidence in the quality of the foundation system.

Sep 8, 2021

By AIME AIME

American Institute of Mining Engineers. (Organized in 1871, and Incorporated in 1905.) OFFICERS. For the year ending February, 1906. Directors JAMES GAYLEY (President), R. W. RAYMOND (Secretary), FRANK LYMAN Treasurer). T. A. RICKARD NEW YORK, N. Y. CHARLES H. SNOW NEW YORK, N. Y. R. W. RAYMOND NEW YORK, N. Y. (Terms expire February, 1906.) JAMES GAYLEY NEW YORK, N. Y. FRANK KLEPETKO NEW YORK, N. Y. FRANK LYMAN NEW YORK, N. Y. (Terms expire February, 1907.) JAMES DOUGLAS NEW YORK, N. Y. JAMES F. KEMP NEW YORK, N. Y. ALBERT R. LEDOUX NEW YORK, N. Y. (Terms expire February, 1908.)

Jan 1, 1906

By G. S. Scott, L. D. Schmidt, J. A. KELLEY, E. L. FISH

One of the war problems with which the Bureau of Mines is concerned is to increase production of iron and steel , in which coke is one of the major factors . The output of byproduct coke for use in iron blast furnaces is insufficient and is being supplemented by coke from beehive ovens (figs . 1 , 2 , and 3) . Some difficulties that cause a reduction in iron output have been reported in the use of some of the beehive coke.6/ About 20 years have elapsed since beehive coke was made on a large scale , and many of the skilled operators of those days are no longer available . Furthermore , in many instances the quality of the coal supplied to the ovens has not been as good as formerly. The ash and sulfur contents are often abnormally high; and in other instances they vary greatly in amount, so that a nonuniform coke is produced . To assist operators to improve quality and yield of beehive coke , the Bureau of Mines equipped a truck as a field laboratory ( fig . 4 ) and sent the authors with it into the Pennsylvania beehive district . The truck contains necessary equipment for sampling and analyzing coke oven gases , measuring temperatures , screen - sizing coal, and float -and - sink testing coal . Coal specimens may be sent to the Pittsburgh laboratory for analysis . Beehive plants producing good coke were visited first to observe details of operation and to collect data on the operating process . These covered temperatures , analyses of the exit ( or trunnel) gases , and coal quality, and were to be utilized in searching for faults in plants not producing good - quality coke and to assist in improving such plants or their operation .

Dec 1, 1943

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

This study investigates the changes in seismic velocity of rockmass before and after three major seismic events to determine any potential identifiable precursory velocity changes associated with these events. Induced stress measurement is one of the challenging tasks in deep underground mining, with extreme impacts on the safety and stability of the mine. This study used p-wave passive seismic tomography to image the velocity redistribution within a rockmass, which can indicate induced stress level changes in the rockmass and detect the velocity changes that might precede a major seismic event or a rockburst. The ultimate goal of this research focus is to develop another tool for the deep-mining community that will help to increase safety and efficiency. For this purpose, the hypothesis of conventional mechanics, which implies induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs, is evaluated. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring; however, the p-wave velocity did increase in the closest “zone center” for two of the three events. 

By S. Noll

Ventilation is an essential part of any underground mining operation. It provides fresh air for workers and machinery, keeps up an adequate mine climate and dilutes and dissipates noxious gases. Possible changes in the economic environment for mining in the future, e.g. increasing energy costs, will necessitate optimization of distribution of airflow within most mines. This paper discusses the scientific set-up for measurements as well as the behavior and influence of parameters of ventilation according to airflow distribution under consideration of technically possible set-ups of mine fans. This study was done in an underground mine with a flat seam room and pillar mining method.

Feb 27, 2013

By R. R. Tatiya

Data obtained from a copper mine were used in a comparative study of the reserve estimates generated by applying geostatistical methods to surface borehole data, underground core drilling results and assay values from chip sampling. Global estimation of the deposit performed by kriging of the low-density sampling data from the surface boreholes did not provide reliable results, but could identify the potentially mineralised zones. The reserve generated from core drilling results correlated well with that estimated from chip sample data and with that estimated by the conventional methods used at the mine. A satisfactory reserve evaluation could, therefore, be obtained by kriging of the data from the underground core drilling alone, provided that a systematic sampling procedure was adopted. Estimates based on chip sampling information could be used as a check, which could avoid the current practice of chip sampling of most of the mine workings. The aim should be to develop a semi-variogram for the deposit, which could be used to estimate the reserves by kriging

Jun 19, 1905

By R. M. Becker

THIS IS a progress report on a study of the application of statistical practice to mine and mineral sampling undertaken by the Federal Bureau of Mines to provide sound theoretical and practical data for use of the mineral engineering professions. One of the problems in mine sampling is determining the reliability of the results. For certain types of sampling data (random data) the reliability of the results can be stated mathematically. For other types of data there is no known means of quantitatively expressing reliability. In applying measures of reliability to a set of random data, some knowledge or assumption of the characteristics of the particular data is necessary. In many fields these characteristics are well known. However, in mining, where the data are in assays, these characteristics are not well known.

Jan 1, 1961

By Robert J. Dompe

The objective of this program was to develop a cost effective microprocessor-based electronic image sensor system for monitoring pit slope displacement to detect and/ or predict impending slope failure in surface mines. A background study and data analysis yielded a performance specification for candidate Video Slope Monitoring Systems. A design concept was developed based on using a pair of solid state video cameras located on precision pointing assemblies. The digital images from the cameras are compared and, using electronic triangulation, slope topology is calculated. The current and past locations of operator selected features are compared to determine pit slope displacement. A proof-of-concept test was performed using a laboratory model of a pit slope. Based on the successful results of that testing it is recommended that an in-mine evaluation be performed using a full-scale prototype Video Slope Monitoring System.

Jan 1, 1982

By Donald R. McMahon

This paper presents a unique case history that documents the use of a braced secant pile wall to underpin a heavily loaded footing inside of a manufacturing plant. Construction of a pit for a new manufacturing process directly next to the footing necessitated the underpinning. The footing supports an overhead crane that needed to remain operational throughout construction of the pit and therefore, settlement of the footing could not be tolerated. The base of the footing was about 7.7 feet above the base of the 17-foot deep excavation. The footing bears on a silty clay deposit that grades from a stiff consistency beneath the footing to a soft/medium consistency near the base of the pit excavation. This paper describes the design and construction of the secant pile wall and bracing to control wall deformations, ground movements and settlement of the footing. The footing was monitored for settlement throughout construction of the pit and no measurable movement was observed.

Jan 1, 2006

By Gheorghe Marin, Franco Chiesa, David Levasseur, Bernard Duchesne

Over the past 20 years, pressure die casting has evolved to a point where structural parts can now be produced by this process. This has been made possible by the development of vacuum die casting and by the development of die-castable, low iron content alloys. This resulted in the production of low porosity, weldable die-cast parts on which heat treatment may be applied. In the present paper, the influence porosities on the tensile properties of as-cast A360 tensile test bars was evaluated. This was done by casting 24 clusters, comprising three 6mm diameter test bars each, in a 280T cold chamber pressure die casting machine after a steady dynamic equilibrium had been reached. Modeling of filling allowed to explain the differences in porosity observed in the 3 samples of a same cluster while the results of solidification modeling were related to the microstructure. Tensile samples were radiographed on a real time X-cube apparatus and separated into 2 lots: samples where no porosity defect were visible and samples with visible defects. By measuring the tensile properties of the 2 lots it was possible to quantify the drop in tensile properties brought about by porosity, which is the most common defect observed in pressure die-cast parts.

Jan 1, 2015