Search Documents

By B Mobilio, M Secheny, J Rachocki, G B. Sharrock, A Jäger, J L. Lett, I Brunton, G W. Capes

Establishment of the Cadia East Panel Cave Stage One (PC1S1) commenced with the firing of the first bell in early 2011. Production began with the completion of the undercut in May 2014. PC1S1 used a post-undercut composed of 114 drawbells covering a footprint area of 73 438 m². The extraction level is located at a depth of 1200 m below the surface and is based on a 32 × 20 m El Teniente layout. Cave establishment required the construction of multiple conveyor drifts, a large-capacity jaw-gyratory crusher and ancillary ventilation and pumping infrastructure. Preconditioning via hydraulic fracturing and blasting was implemented at various locations of the cave block height. This paper presents an overview of the key learnings from the commencement of undercutting to surface breakthrough, including rock mass classification and modelling, stress measurements, preconditioning, numerical modelling and cave monitoring.CITATION:Lett, J L, Brunton, I, Capes, G W, Jäger, A, Mobilio, B, Rachocki, J, Sharrock, G B and Secheny, M, 2016. Undercutting to surface breakthrough – Cadia East panel cave (stage 1), in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 65–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By D. L. H. Bulbring

The removal of a cylindrical core from thick-wall sections for creep analysis by the relatively new Weldcore® process represents a very exciting methodology for obtaining more representative creep damage data from large engineering structures. The cylindrical core that is removed, representing about 60% of the wall thickness, leaves a substantial removal site that needs to be repaired. This paper presents data pertaining to taper Friction Hydro Pillar Processing as an alternative repair technique for filling the core removal site. Process parameters were evaluated with special attention being paid to the effect of downward force on process response variables, weld defects, and mechanical properties of 10CrMo910 steel. Process temperature and torque response as well as total process energy input were also considered. This paper also assesses the static and dynamic performance of this repair technique. The influence of a varying downward force and the occurrence and position of discontinuities were quantified. Downward force was shown to have the most notable effect on weld joint dynamic performance and was found to be related to the process temperatures achieved in close proximity to the weld interface.

Jan 1, 2013

The Bureau of Mines conducted large-scale laboratory copper ore leaching tests to enable improving copper recovery from large dump-leaching operations. This was done by comparing leaching progress when copper was recovered from recycled leach liquor either by cementation or by solvent extraction. Copper was leached from 7-ton ore samples at room temperature using pH 2 ferric sulfate solutions. With are samples containing 11 percent minus 0.5-inch fines, no marked advantage in using either of the copper recovery methods was evident after 416 days of leaching. With ore containing 32 percent minus 0.5-inch fines, solvent extraction of copper was advantageous in that 60 percent of the copper was extracted after 568 days, whereas only 48 percent of the copper was extracted when cementation was used. Less acid was consumed during leaching when solvent extraction, rather than cementation, was used for copper recovery. Iron, contributed by cementation with scrap iron, plugged the ore bed containing 32 percent fines.

Jan 1, 1981

Three complete connector assemblies and ten separate contacts were submitted to a series of tests to establish the connector permissibility and compliance with the Bureau of Mines' research Contract H 0110423. Test Procedure TPC-0100 was coordinated, and the test plan approved by the Bureau as fully complying with the intent of the contract for the low voltage, medium voltage and high voltage A.C. connectors. The components and connector assemblies have been demonstrated in testing that they meet or exceed all the requirements of the test procedure.

Jan 1, 1972

By Sergio N. Monteiro

Polymeric composites reinforced with natural fibers are increasingly been used in several engineering applications, from automotive parts to building construction elements. In addition to the relatively low cost, the natural fibers are also appraised by their renewable and biodegradable characteristics. Fibers extracted from the crust of coconut fruits, also known as coir fibers have been investigated for a possible use in composite materials. In the present work, the coirfiber/polyester matrix interfacial strength was evaluated by means of pullout tests. The variation of the pullout tensile stress vs. the embedded coir fiber length permitted to determine the critical fiber length and, thus, to calculate the interfacial strength. Observations by SEM complemented the results from pullout tests, indicating that coir fibers have a potential for application aspolymeric composites that could replace conventional materials such as wooden and gypsumpanels.

Jan 1, 2006

By José Cuadros

"El presente trabajo señala el proceso de evolución del método de minado en la mina Chupa, perteneciente a la unidad minera de Iscaycruz. La evolución del método de minado se determinó por la búsqueda de mejores condiciones de seguridad y eficiencia en la operación. En ese sentido, los resultados logrados con cada una de las alternativas de minado por subniveles, indica que se ha logrado optimizar las diferentes variables mineras y cumplir con el plan estratégico de Empresa Minera Iscaycruz S.A. (EMISA). Para cumplir con el citado plan estratégico, se debe optimizar el método de minado de Chupa, a través de una mayor producción a un menor costo,así como del aprovecho de las labores de desarrollo y preparación ejecutadas según el planeamiento inicial del minado. Por ello, la secuencia del avance del minado y la reestructuración del sistema de relleno de la mina son los aspectos importantes para lograr este objetivo. "

Jul 31, 2003

By J. M. Galera, M. D. Rodriguez, V. Pozo, S. Cooper

"Cobre Las Cruces mine extracts copper minerals from a VMS deposit located in the well-known Iberian Pyrite Belt (IPB). As an open pit, it is distinguished geologically from other IPB mines by the presence of around 150 m of Tertiary soft marls, known locally as the Guadalquivir Blue Marls, followed by a regionally important aquifer. Below the marls and aquifer the mineralization is hosted by rocks typical of the Palaeozoic within the IPB, comprising gossan, tuffs, slates, and sulphides.This combination of a substantially soft rock and more competent, older (but still occasionally problematic) Palaeozoic lithologies constitutes a unique geological framework and presents substantial challenges in maintenance of slope stability, and therefore operational safety, at the mine site. This paper describes the fundamental design, excavation, and monitoring measures implemented at the mine to maintain safe production, and the lessons learnt during the mine development. IntroductionAs a modern Spanish mine, Las Cruces is committed to the use of best available technology and practices with the aim of guaranteeing the production of ore in a safe environment. From a practical perspective, this implies the realization of a high quality pit design, ongoing geotechnical mapping of exposed slopes to ensure conformity with design, and use of leading geotechnical surveillance technology to complement visual observations. The focus of this article is to illustrate how, at a mine site with potentially problematic soil/rock conditions, multiple advanced techniques employed from design stage analysis through to final pit configuration and vigilance, were combined to achieve an overall control of the ground conditions. In Figure 1 the layout of the pit is shown, illustrating development at the beginning of 2015."

Jul 1, 2019

By A. Wahab Khair

Coal mining has evolved into extensive use of continuous mining machines for development and production. This has resulted in an increase in dependence on the versatile continuous miners. The present-day continuous miners are powerful in terms of rated power but are still plagued by wear of bits which hinders development and production as the bits have to be continuously changed at regular intervals. Previous attempts to analyze bit wear has been either restricted to the theoretical approach and or laboratory testing. This paper discusses about the overall aspect of bit and drum design for different conditions. Using the laboratory model set up, numerical models and field testing, a new bit and drum design was analyzed to evaluate their performance under different conditions. The results proved that a newer bit design and drum design were successful in limiting the amount of wear as well as improving the performance of the continuous miner and production.

Jan 1, 2008

Surface subsidence that results from longwall mining can be large magnitude and can affect significant areas. Conventional methods for subsidence monitoring include leveling, global positioning system (GPS), and photogrammetric surveys. Remote sensing techniques, including aerial LiDAR, terrestrial laser scanning, and satellite-based differential interferometric synthetic aperture radar (DInSAR), are also used to measure deformation associated with subsidence. DInSAR data are different than data from conventional subsidence surveys. Images capture data over large areas (hundreds of kilometers), and each pixel (data point) in an image quantifies the average displacement over an area of square meters. DInSAR data can have fairly high time resolution; imaging periods typically range from weeks to months.

Jan 7, 2020

By Richard F. Hewlett

Engineers at the Bureau of Mines Denver Mining Research Center have been a research program investigating the theory and application of mine sampling. Part of this program is an investigation of the efficiency of sampling methods that involves development of sampling-method theory through simulating ore-deposit samples and assays, using - electronic digital computer. Theoretical developments are checked against actual ore-deposit sampling, assay, and production data by the commonly used polygonal and triangular methods of computing grade and tonnage of ore reserves. To speed the computing procedures, a program has been developed utilizing a medium-size digital computer for computing ore reserves by the polygonal method. This program calculates nine prismoids per minute at a total cost of $0.21 per prismoid. The complete program, written for an augmented IBM 650 computer, is described in detail; it can be used without change for computing ore reserves for a low-grade deposit. Modifications necessary to convert the program to compute ore reserves for virtually any other type of deposit or grouping of ore horizons also are given; however, the program is limited to using only vertical drill-hole data.

Jan 1, 1962

By Chen Song

Keywords: Co3O4, Cobalt Compounds, Morphology, Urea, Homogeneous Precipitation Depending on experimental condition, precipitation from cobalt nitrate and chloride solution in the presence of urea yield dispersed cobalt compounds with different chemical compositions and morphologies. The effects of concentration of cobalt solution and urea, agitation, on precipitation morphology were investigated experimentally. Generally in closed systems the particles are identified as cobalt (II) basic carbonate with needle type shape. In open system, spherical and plate-like precipitations of cobalt (II) basic cyanate are formed. The chemical formula of cobalt compounds was confirmed. They are CoII,III(OH)0.83(CO3)0.49 Ay?0.14 H2O (in tightly-capped reactor: A stands for NO3?, Cl?; y[A]molecular weight < 12.9) and CoII,III(OH)0.83(NCO)XAy?0.14 H2O. (in open reactor A stands for: NO3?, Cl?; 42 x + y[A]molecular weight < 44.82). The main reason was that the primary particles had different chemical compositions for the effects of the different kinds of anions and stoichio-chemical compositions of the primary particles. The effect degree of the anions depended on the co-existing anion radius in the reaction solution. According DTA-TG analysis of the cobalt compounds, the latter particles transform to Co3O4 powders on calcining. The shape of the Co3O4 particle with porous character has inheritance with precipitation. In this paper, it concludes that the particle formed by the principle of nucleation-aggregation in aqueous solution. The process of aggregation has played an important role in formation of particles. During calcination, the aggregation would be destroyed partly.

Jan 1, 2005

By J. R. Lucas, R. L. Frantz

Mine sealing programs for the alleviation of acid mine drainage were begun by the Federal Government in the &apos;30&apos;s. As part of an acid mine research project to The Ohio State University, a field test was undertaken to determine the effectiveness of mine seals for reducing mine acid. Details of the tests made at the McDaniels mine show the feasibility of air-sealing and flooding an acid-producing drift coal mine. Work by the University continues. The Federal Government undertook in the early thirties an extensive mine sealing program for the alleviation of acid mine drainage. In the states of West Virginia, Ohio, and Pennsylvania many general summaries have been made on this program but no critical evaluation with supporting data has been found on the effectiveness of mine seals for reducing mine acid. Because of this it was decided to undertake a field testing program as part of an acid mine research project of the Engineering Experiment Station, The Ohio State University. The objective of this phase of the project was to develop and install a field research laboratory for acid mine drainage studies. Specifications for such a mine laboratory were developed and resulted from the following considerations: 1) Size and preservation—the test mine shou1d be of limited size to permit frequent and detailed examinations; it should be in a reasonably sound condition to permit safe entry. 2) Isolation—the mine should be physically separated from all other mines. 3) Openings—a minimum number would be desirable to reduce the sealing problem. 4) Structure—the mine especially near the openings should be structurally sound. 5) Acid production—the mine should be producing significant quantities of acid. After considerable searching, the McDaniels mine was selected in the Hocking coal field in Vinton County just above Lake Hope State Park in southeastern Ohio. The small drift mine in the middle Kittaning coal consisted of two small rooms with one mine opening about 6 ft above a seasonal stream bed. Before it was finally decided to seal the mine, a short study was made of the acid drainage over several months. Fig. 1 shows a plot of acidity (milligrams per liter), flow (gallons per minute), and acid production (pounds per day) vs time over the sampling period. Because the coal was overlain with a porous sandstone, the mine drainage was consistent the year around even though the mine was

Jan 1, 1961

By P. G. Flood

A simplified conceptual model shows how the arc flank to arc fringe areas adjacent to ignimbritic centres form a prospective zone for natural zeolites. Large alkaline lakes that serve as the repository of voluminous ash-fall tuffaceous material provide the ideal chemical setting for pervasive alteration of silicic glass to zeolites. The unusually old age of the Escott deposit demonstrates that any silicic volcanic province that contains low-temperature, unmetamorphosed sequences is a potential zeolite exploration target and that age should not be used as a criterion to exclude potential areas. It has also been demonstrated that heulandite and mordenite, formed by diagenetic alteration of silicic glass, do not always change to analcite and albite through the ageing process

Jan 1, 1991

By S. H. Lorain

Mechanized dirt-moving equipment has greatly increased the scope of prospect trenching by lowering the costs and increasing the speed of such work. Where the soil covering was more than 3 or 4 feet deep, operators were quickly discouraged and abandoned surface exploration in favor of shaft sinking, drifting, or diamond drilling; wildcat trenching was seldom undertaken, even where the soil covering was thin. Although power shovels, trench diggers, and draglines are useful under special conditions, caterpillar-mounted angledozers will usually do the same type of work and have a far wider range of adaptability. They are therefore incomparably the most generally useful equipment for the purpose. Since 199 the Bureau of Mines has been engaged in a widespread search for minerals useful to the war program; this work required a great deal of pioneer exploration in areas where known outcrops were marginal or subcommercial by pre-war standards. Engineers in charge of field operations were quick to perceive the applicability of mechanized trenching on a fairly large scale, particularly in the Northwestern States, where completely exposed vein-outcrops are rare. Probably no other organization to date has done a comparable amount of angledozer prospect trenching under such a wide range of conditions. The following comments and accompanying cost tables are based on work performed chiefly in Idaho, under a variety of physical and climatic conditions. The most important applications of the angledozer for such work may be described under three heads:

Jan 1, 1944

By Leo F. Reinartz

It was with humility that I accepted the invitation of the Board of Directors of our Institute to deliver the Twentieth Howe Memorial Lecture. Many previous lecturers could speak from personal experience of the great work done by Professor Howe. It was not my privilege to be one of his students but, indirectly, I came under the influence of his work many years ago. My mentor in Metallurgy at Carnegie Institute of Technology, Prof. Fred Crab tree, was an ardent admirer of Professor Howe and his work. Professor Crabtree taught me early to appreciate Professor Howe&apos;s love of truth and keen desire to find a scientific reason for every metallurgical phenomenon. In this early search, Professor Howe encountered many unexplainable facts. Nevertheless, in the classic text, "The Metallurgy of Steel," published in 1891, he indicated that he believed Research could light the way. Under the heading of "The Treachery of Steel" he said: "In the early use of Bessemer and Open Hearth Steel, many then unexplained and hence mysterious failures occurred. With our present knowledge, an easy explanation of most of them would probably have been seen. But even today certain unexplained and apparently inexpli- cable failures occur in steel; inexplicable in spite of full and intelligent investigation." Then Professor Howe continued to talk about "the trustworthiness of steel" in the following manner: First, the steel-maker has learned by experience. He knows today far better the effects of a high percentage of carbon or of phosphorus; of cracks, pipes and blow-holes; of segregation and imperfect mixing; of over-heating; of finishing too hot or too cold. Knowing, he guards against them more effectually, and keeps at home much steel that he would formerly have sent into the market. Those who would not, or could not learn and do, have been driven out of the business; the conditions necessary for producing good sound steel by the acid Bessemer and the acid Open Hearth processes have been mastered. By and by, the basic process came along with new conditions, new liabilities to unsoundness, a great hue and cry about mysterious fractures followed, and Lloyd&apos;s register provisionally forbade the use of basic steel. Much basic steel was irregular and brittle throughout; too much carbon, too much phosphorus, too cold teemings—imperfect mixing. Still there was little doubt that, with further experience, these difficulties of the basic process would be mastered as those of the acid process had been. This shows that Professor Howe could not take anything for granted. Believing that careful research would find the answer to all mysterious phenomena, he was several generations ahead of the practical acceptance and adoption of this principle.

Jan 1, 1943

By Leo F. Reinartz

It was with humility that I accepted the invitation of the Board of Directors of our Institute to deliver the Twentieth Howe Memorial Lecture. Many previous lecturers could speak from personal experience of the great work done by Professor Howe. It was not my privilege to be one of his students but, indirectly, I came under the influence of his work many years ago. My mentor in Metallurgy at Carnegie Institute of Technology, Prof. Fred Crab tree, was an ardent admirer of Professor Howe and his work. Professor Crabtree taught me early to appreciate Professor Howe&apos;s love of truth and keen desire to find a scientific reason for every metallurgical phenomenon. In this early search, Professor Howe encountered many unexplainable facts. Nevertheless, in the classic text, "The Metallurgy of Steel," published in 1891, he indicated that he believed Research could light the way. Under the heading of "The Treachery of Steel" he said: "In the early use of Bessemer and Open Hearth Steel, many then unexplained and hence mysterious failures occurred. With our present knowledge, an easy explanation of most of them would probably have been seen. But even today certain unexplained and apparently inexpli- cable failures occur in steel; inexplicable in spite of full and intelligent investigation." Then Professor Howe continued to talk about "the trustworthiness of steel" in the following manner: First, the steel-maker has learned by experience. He knows today far better the effects of a high percentage of carbon or of phosphorus; of cracks, pipes and blow-holes; of segregation and imperfect mixing; of over-heating; of finishing too hot or too cold. Knowing, he guards against them more effectually, and keeps at home much steel that he would formerly have sent into the market. Those who would not, or could not learn and do, have been driven out of the business; the conditions necessary for producing good sound steel by the acid Bessemer and the acid Open Hearth processes have been mastered. By and by, the basic process came along with new conditions, new liabilities to unsoundness, a great hue and cry about mysterious fractures followed, and Lloyd&apos;s register provisionally forbade the use of basic steel. Much basic steel was irregular and brittle throughout; too much carbon, too much phosphorus, too cold teemings—imperfect mixing. Still there was little doubt that, with further experience, these difficulties of the basic process would be mastered as those of the acid process had been. This shows that Professor Howe could not take anything for granted. Believing that careful research would find the answer to all mysterious phenomena, he was several generations ahead of the practical acceptance and adoption of this principle.

Jan 1, 1943

By W. Sondermann

"AbstractWith the increasing demand in reuse of inner city areas and the urgent need for deeper foundation pits under cramped circumstances, adjacent structures close to and high ground water level, the well-known established technologies especially with small to mid-sized dimensions are often too time consuming and occasionally not economic to install lateral support systems. The alternatives for these specific cases could be the usage of the deep mixing technology to create lateral support systems in reinforcing the deep mixing elements additionally to transfer the horizontal loads from earth – and water-pressure.With increasing demand in depth and water tightness, verticality and overlapping of single column solutions are becoming the key in execution. In addition, for some applications subsoil-conditions were not ideal for wet deep mixing technologies. The tubular soil mixing system (TSM) as a combination of mechanical mixing and support of hydraulic cutting by jet grouting can provide solutions toovercome these challenges.1. Current market conditions and trendsThe present financial crisis and the efforts not only to consolidate national budgets, but also to rescue certain banks, have not left the building industry unaffected either. Some drastic cutbacks to public budgets, along with the increasingly restrictive granting of credit for the financing of construction projects, have led to enormous over-capacities in the building sector, with purely negative impact. As a consequence of these negative developments, many companies are experiencing the pressure to restructure more quickly and to reduce costs but at the same time to keep the consequences of all activities, both externally and internally, within limits acceptable to employees, owners and finance institutions and last but not least consumers."

Jan 1, 2014

By T. P. Williams, M. B. Rydzewski, B. Corner

Konkola Copper Mines (KCM) plc is an integrated copper producer operating on the Copperbelt in Zambia. KCM has numerous mining operations located in the towns of Chililabombwe (Konkola Mine), Chingola (Nchanga Open Pit and Underground operations), Lusaka (Nampundwe Mine), with a smelter located in Kitwe (Nkana Smelter) and an SX-EW plant in Chingola (Nchanga Tailings Leach Plant). [ ]

Jan 1, 2005

By C. Treworgy, C. Chenoworth

Geologic and technical factors such as coal seam thickness, stripping ratios, roof conditions, partings, faults, and size and geometry of the reserve block greatly impact the availability of Illinois coal for mining. Residential and commercial developments also restrict access to coal reserves in some areas. Despite the collective effects of these factors, large blocks of bituminous coal reserves suitable for efficient, low-cost underground mining remain available in Illinois.

Feb 24, 1997

By Fritz Grübl

Modern shield TBMs allow tunnel drives through almost any type of ground. Thanks to high elaborated technical measures, significant subsidence of the ground surface can be almost entirely avoided. The tunnel lining behind the TBM must be capable of withstanding all loads without deforming, especially during ring erection and advance. Single-shell tunnel linings behind the TBM, usually reinforced concrete segmental rings, can be designed to fulfill this demand. With many projects, however, damage occurs to the lining. Repair costs may be extremely high. Reasons for damages and possibilities to avoid them are shown and explained.

Jan 1, 2001