Search Documents

By Gregory A. Stephan

A case history of design, prediction, probe pile driving, and construction of a pile foundation for Building 3 of Waterside at Bay Beach Condominiums located in Fort Myers Beach, southwest Florida, is presented. Site geometry constraints, the presence of a 12.0 ft (3.6 m) deep lake occupying the southern one-third portion of the proposed building footprint, and marginal subsoils provided specific challenges for design and construction of the foundation. The subsoil conditions were explored by performing Standard Penetration Test (SPT) borings and a Piezocone Penetration Test (PCPT) Sounding to depths of 100 ft (30.5 m) within the building footprint. Additionally, borings were performed to envelope the building. Deep foundation alternatives included driven concrete, monotube, and steel pipe pile as well as drilled shaft. Following an evaluation of high structural loads, site-specific constraints, foundation test data from buildings 1 and 2, and preference expressed by the project owner, a pre-cast prestressed concrete (PPC) pile-supported foundation system was selected as an economical and effective foundation approach. Use of an augered cast-in-place (ACIP) pile foundation system was precluded by the project structural engineer. This paper deals with the design aspects and methodologies utilized in choosing and economizing the foundation system. The building foundation was designed for an allowable pile capacity of 40 tons (353 kN) in compression, 1.5 tons (12 kN) in lateral capacity for a deflection of 0.25-in (0.64 cm) and 15 tons (133 kN) in uplift capacity. For the single story extended garage structure, a pile capacity of 27 tons (238 kN) was indicated in compression. As part of the design process, an extensive probe pile driving program was carried out in order to evaluate the pile driving equipment, determine and verify pile capacities, and optimize the production pile lengths. A total of 33, 14-in (356 mm) square, PPC concrete piles were driven within the entire building limits, and dynamically load tested utilizing Pile Driving Analyzer (PDA) as part of the probe pile driving program. Utilization of PDA during probe pile driving helped in predicting pile set-up (i.e., increase in pile resistance with time) as well as reducing the pile lengths by as much as 20 percent. It resulted in variable pile lengths during the production phase. This information was effectively utilized as part of the overall quality control program to install a total of 559 PPC piles (including 33 probe piles) within the Building 3 footprint, including the reclaimed lake area, to depths ranging from 45 to 58 ft (14 to 18 m) below existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared reasonably well with the capacities from the CAPWAP analyses for probe piles. This engineered, monitored and tested foundation solution provided a cost effective and satisfactory basis for completion and approval of the foundation work for the building resulted in cost savings over other foundation alternatives for the owner. The building has since been occupied and a recent reconnaissance has indicated that the building foundations are performing satisfactorily.

Jan 1, 2003

By M Donghi, G Ramage, A Barnes

As the mining landscape continues to transform, the challenge of accessing deeper orebodies quickly and safely is becoming a frequent topic of conversation amongst those in the mining industry. The rapid development of underground mine entries to gain earlier access to deeper orebodies is an ever-present challenge to mine owners and contractors. Overcoming this and providing economical solutions to unlock the value in these deeper deposits is a challenge that should be confronted.In 2013, Redpath Australia Pty Ltd (Redpath) commenced construction of what would be the first of two drifts excavated through the use of a tunnel boring machine (TBM) in Queensland’s Bowen Basin.The excavation and development of the two drifts (declines) was completed as part of a contract for underground mining services between Redpath and Anglo American at the Grosvenor Coal Mine Project in Central Queensland, located approximately 5 km north of the town of Moranbah. Having recently completed the drift development, this paper will extend on the early writings of Donnelly, Ramage and Donghi (2014) and provide detail on the operational achievements, advance rates, threats, opportunities and learnings during the excavation of the two declines: the conveyor (CV) drift and the transport (M&M) drift.CITATION:Ramage, G, Donghi, M and Barnes, A, 2016. Experiences gained through tunnel boring machine decline development, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 695–712 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By L. E. Fish, G. S. Wyman

CHUQUICAMATA open-pit mine is capable of producing a total of 105,000 tons daily. When the sulphide plant is operating to capacity the distribution of this quantity will be approximately 30,000 tons sulphide ore, 30,000 tons oxide ore and 45,000 tons of waste. At that time the combined capacity of the oxide and sulphide plants will be about 540 million lb of copper per year. Twenty one benches have been opened to date and all are still active except the three top ones at the northeastern limit of the pit. These have been pushed back to final slope line. The pit is 8850 ft long, 3540 ft wide and 980 ft deep. Benches are not all developed to a standard height as the large development shovels used in cutting new benches have been of different size and range. At this time new benches 521 ft high are being developed with an' 11-yd shovel. Ore haulage through the greater part of the pit operation has been on down grades to the crushing plant. With the opening of bench F-4 in April 1944 the first adverse-grade ore haul was encountered. Of the total tonnage now being mined, 35 pct comes from the four benches that are below the level of the crushing plant yard. Waste had been dumped on the same or nearly the same level as the bench from which it was removed up to the opening of bench F-4. Waste from this and lower levels is hauled to the level of the crusher, yard where it must cross the flow of ore traffic to reach the only available dumping space to the east of the mine. The average ore haul is 3.13 miles one way shovel to crusher, and the average waste haul from that portion handled by railroad is 3.32 miles one way from shovel to waste dump. Waste that is being removed by truck haulage from the upper part of the -mine is hauled an average of 1 mile. Ore loaded by trucks is hauled 3/4 mile to a car loading ramp and then by rail to the crushing plant. Drilling and Blasting There are two types of development for blasting being used: One for opening new benches and the other for bank shooting. The former consists of 9a in. diam churn-drill holes drilled 11.8 ft center to center in rows 10.2 ft apart with the holes staggered in the rows thus giving an equilateral-triangle pattern of 11.8 ft on a side. After the first block, 492 ft long by 71.5 ft wide, is shot in the pattern described above, the cut is advanced by smaller shots consisting of four rows of holes spaced 23 ft center to center with the rows 23 ft apart. These shots are fired in conjunction with side shots in which the holes are drilled 33 ft center to center and 29.5 ft back from the toe, thus squaring up the bank for subsequent shooting. An average bank shot consists of about 60 holes drilled in two rows parallel to the face, 30 holes to

Jan 1, 1952

By M. du Plessis, D. F. Malan

"The aim of any mine design is to ensure that the excavations remain stable for the period they will be in use. Various pillar systems are used to ensure that underground stopes remain stable and that mining activities do not affect the surface infrastructure through either surface subsidence or seismicity. Intermediate-depth platinum mines make use of in-stope pillars designed to fail while the pillars are being cut at the mining face. The pillar stress exceeds the loading capacity and the pillars crush as a result. The aim of the paper is to provide an overview of in-stope crush pillars. This will include the application, behaviour, function, mechanism, impact, and design of a crush pillar system."

Jan 1, 2015

By Ron Lutz

In today’s world, production is the name of the game. We are all in business to make money. In the Quarrying and Mining industry the same holds true. The primary goal is to develop the best drilling and blasting program available to maintain uniform fragmentation to maximize production. Also we want to maintain drilling and blasting costs and minimize escalators. This paper is intended to discuss ways for all parties (quarry’s, blast service and drill companies) to attain this through understanding what can be done to help blasthole drilling and production. Blast designs and seminar’s emphasize the accuracy of drilling to produce better fragmentation. Blast design must also include basic concepts in the drilling process. The type of drill to be used for example whether it is a crawler or truck mount, top hammer or down the hole is important. Quarry operators have a role to play as well. They hold the key to the production of drilling. What the customer does or does not do has a direct effect financially to the drilling. The phrase of pay me now or pay me latter comes to mind. This paper will explore the detail of planning that is required by the quarry and/or blast service companies before a single hole is drilled. The drill must be able to meet the production need of the operation. The type of drill available and what can and cannot be done. The drill cost must be competitive. This paper will touch on comparison drill costs from 1967 to 1999.

Jan 1, 2000

By Ronald Branstetter

Gaseous and particulate exhaust emissions from 20 diesel engines in service at five underground mines were measured with high accuracy instrumentation. The engines that were tested were checked for faults or maladjustments. The vehicle and engine maintenance organization was studied at each mine and an idealized maintenance program was devised. Faults were induced in a new diesel engine to determine their effect on the characteristics of the exhaust emissions. The results, conclusions and recommendations from this investigation are presented in this final report.

Jan 1, 1983

By R. D. Dukimo, M. V. Sevian

The nature of fracture and factors that control the extent of fracture in the tumble-drum and drop-tower tests have been identified. The product-size distribution, on which the standard strength indices for these tests are based, and the breakage rate constants depend on a number of factors other than the strength of the lumps. The standard indices and rate constants are meaningful only in a comparative context and for events whose loading mechanism is similar. The results of experiments on three Australian ores, from Yandi, Koolan and Mount Whaleback, are used in combination with fracture mechanics theory to explain why different tumble-drum standards have been found to be fully consistent. A more meaningful measure of strength could be the parameters of the Weibull function, scatter and average strength

Jun 19, 1905

By H Aral

A rotating magnetic field can be produced in a magnetic separator by using a magnet rotor fitted with alternate north-south magnetic poles, similar to the rotors currently used in modern eddy current separators. Rotation of the magnetic field causes ferromagnetic particles to rotate during magnetic separation. The particle rotation can then be used simply to remove entrapment during a conventional attraction magnetic separation (RMF lift separation), or it can be used to roll particles away from non-rotating particles, and to move them out of the separator under their own rotation (RMF rotation separation). RMF (rotating magnetic field) separation is a separation for ferromagnetic particles. These particles have a very ordered magnetism that is locked into directions of easy magnetisation in the crystal. As a result, if the external field rotates, the particles attempt to rotate with it. RMF separation uses this fact to rotate the ferromagnetic particles in a rotating field. In contrast, paramagnetic particles have a magnetism that can point in any direction with almost equal ease, and these will not rotate in a rotating field. By making use of this difference in magnetic properties, RMF rotation separation can separate ferromagnetic particles from paramagnetic, even when the particles have similar susceptibilities. Some particles such as both chrome spinel and ilmenite can contain ferromagnetic regions within a paramagnetic matrix. These ferromagnetic regions can vary from very small regions dispersed throughout the crystal, through thin lamellae, to larger more bulky regions. Although most natural ilmenite is ferromagnetic and generally has a higher magnetic susceptibility than paramagnetic chrome spinel, the susceptibility ranges for the two minerals overlap considerably (Allen, 2000a) due to the presence of these ferromagnetic elements, frequently making the conventional magnetic separation of these two minerals impractical. It is known that roasting a mixture of ilmenite and chrome spinel particles increases the magnetic susceptibility of the ilmenite while leaving the spinel susceptibility substantially unchanged. This makes the use of conventional (susceptibility attraction) magnetic separation more practical for the separation of these two minerals. However, very little is known about the effects of roasting on the response of ilmenite and spinel particles to a rotating magnetic field. For example, although the optimal ilmenite roasting conditions for conventional magnetic separation are quite well established such conditions may or may not be optimal for RMF rotation separation. Low intensity conventional magnetic separation on the basis of magnetic susceptibility can be made more accurate if it is carried out in a rotating field, because the rapid spinning of the separating particles prevents the formation of magnetic flocs, and reduces entrapment and entrainment. Medium intensity RMF rotation-only separation (no attraction component) has the ability to separate rotating (ferromagnetic) from non-rotating (paramagnetic) particles, irrespective of their relative magnetic susceptibilities. RMF rotation separation is of particular interest in this case because ilmenite particles generally rotate much better than the mainly paramagnetic chrome spinel particles, and roasting could enhance this difference further. Further information on the use of RMF to separate minerals can be found in Allen (2000a; b and c). The aim of this series of tests on a number of Australian ilmenites was to compare some different oxidising and reducing roast methods and to establish whether the use of RMF rotation separation improves the chrome spinel rejection.

Jan 1, 2001

By H. Walqui, C. Noriega

Southern Copper Corporation (SCC) is one of the world’s largest copper companies and is finishing the modernization of the Ilo copper smelter. A single ISASMELTTM furnace will start smelting 1,200,000 tons per year of concentrate at the end of 2006. Three existing Peirce Smith converters are being upgraded plus a new one for converting the matte to blister copper is being installed. Two new anode furnaces and a twin anode casting wheel have being operating since January 2006. This represents one of the main changes in the process because the final product of the smelter is now anode copper instead of blister copper. A new oxygen plant, acid plant, and others facilities are in the ramp-up stage. This environmental project will ensure that the new smelter will comply with the environmental regulations of Peru by the end of January 2007. This paper summarizes the background to the modernization project, describes the different stages of the project including engineering, procurement and construction, describes the main areas of the new copper smelter and also the pre-operational testing, commissioning and start-up of them. This is a brown field project with a target of reducing as much as possible the production losses of the existing operation. This paper presents the details of the development of the Ilo Smelter Modernization Project and explains the main aspects of the new facilities, the products to be obtained and the associated facilities for their commercialization, including a Marine Trestle for bulk acid exportation.

Jan 1, 2007

The Kingsgate molybdenite pipes are considered on petrochemical data and field occurrence to be, possibly, epi-magmatic plutonic offshoots grading into hydrothermal bodies. There is reason to believe that the ore is derived from a highly acid granite of type similar to that of the tin bearing areas of northern New England. The mineralogy, microtextures and paragenesis of the ore are discussed.INTRODUCTIONThe Kingsgate Mining Field is situated in steep, heavily timbered terrain 18 miles E.N.E. of Glen Innes and 430 miles north of Sydney. Bismuth and molybdenum ores were discovered at Kingsgate (Yarrow Creek) in 1877. Subsequently some 50 pipes were developed yielding tonnages which at the peak of operations, 1905 to 1920, rivalled production from the rich deposits of northern Queensland.Attempts to revive the field have been made periodically and small parcels of ore have been forthcoming.' During World War II demand for piezioelectric quartz again focussed attention on Kingsgate but twinning and other imperfections of the quartz prevented all but a minor exploitation of the otherwise noteworthy crystals of this locality.There is reason to believe that the ore at Kingsgate is not exhausted through exploration and mining costs would probably be high due to the capricious nature of the pipes and to the irregular distribution of rich ore shoots within them.

Jan 1, 1962

By Frank L. Wideman

THE TREND towards larger quantities of waste in materials handled at metal and nonmetal mines (excluding fuels) continued. A gain of 10 percent from 1962 in the tonnage of waste removed in mineral operations reflects the kind of technological problems being encountered. Technology has a major role in the mineral industry in the task of supplying raw materials obtained from resources occurring beneath the surface of the earth and used in manufacturing commodities essential to modern living. Changes in technology are often brought about by such factors as variations in economic conditions, differences in physical properties of raw material and changes in mineralogical compositions of ore. Mining is usually begun on the richest and most accessible of known deposits, and when these are exhausted, is continued with leaner ores or with less accessible deposits that are either lying at greater depths or are more remote from markets. The increasing difficulties of extraction and depletion of reserves are offset by improvements in extraction technology, improved transportation, and exploration for new deposits. Although depletion has prevailed at many individual mines and in many districts, technology has been the means of providing for increasing demands of an expanding economy with adequate supplies of minerals despite either the changing character or decreasing grade of certain ores. This has been accomplished by various methods applicable to minerals. Among the implements of technology are utilization of lower grade or more complex refractory ores by mass mining, concentration, processing, recovery of byproducts, and mechanization. Better methods to find concealed deposits or to penetrate to greater depths also have been helpful in maintaining a supply of particular minerals.

Jan 1, 1964

By J. B. Forrester

In the operation of the coal mines in Utah few adverse conditions confront us. Physical conditions for the economical extraction of the coal are as near perfect as it is possible for them to be. Still several obstacles are encountered to keep up our interest and prevent us from getting in a rut. Of these I shall speak only of Burning, Wants, and Sluffing of Ribs. Should one travel the outcrop from Ivy Creek in Emery county to the Utah-Colorado line, there would be one outstanding feature indelible impressed upon one's mind. That feature is the omnipresent indications of burning in place. Viewing the eastern escarpment of the Wasatch Plateau from a distance, many splotches of dark red are plainly seen always lying above the coal floor. This stratum is a felspathic sandstone, appearing as a white line running the full length of the above escarpment and about midway between the floor of the valley and the top of the plateau. The coal bearing complex consists of shales, sandstones and coal. This complex varies from two hundred to eleven hundred feet in thickness. The number of coal seams are exceedingly variable. As a rule the argilutites form the bulk of this complex. This material is baked by the burning of the coal and the iron present is oxidized to the ferric state, coloring the shale to a dark red. This baked material forms a shingle tales that in places cover the entire complex. It is natural to expect that the most extensive burning is in the canyons facing to the south and east and on the south slopes of the ridges running to the east or west. Such, indeed, is the case. Still in this arid region many crop fires have existed upon the north slopes, especially in those canyons that face to the east. In fact today, instances are not rare where grassy north slopes, heavily timbered with balsam and fir that have attained a diameter of 14 to 24 inches, are found growing upon the disintegrated baked shingle and later development proves that the coal has been burned at least 500 feet back from the outcrop. Still these conditions are not normal. In this arid climate the south and east exposures are steep and barren, except for the scrub pine, cedar, mahogany and kindred semixerophytes. Bunch grass is also a lover of such exposures. There is very little soil found in such places; it is either blown away as fast as formed or washed away by the rare torrential rains, or the rapidly melting snow. Thus we see that the physical conditions are favorable for the starting and maintainence of outcrop fires. This brings us to the probable origin of this phenomenon. There are four probable ways' that such fires, could be started, namely:

Jan 1, 1921

By J. G. van der Watt

Due to increasing concerns of global rare earth element shortfalls in the near future, possible alternative sources of rare earth elements have recently become of economic interest. One such alternative is decanting acid mine water originating primarily from abandoned old mines in the Witwatersrand region of the Republic of South Africa. In this study, a novel way of rare earth element removal from the acid mine drainage was employed, making use of bentonite clay, which has very good adsorbent properties, as a rare earth element carrier material. The process can be economically viable only, if the elements can be selectively removed from the bentonite clay carrier material so as to yield reusable clay. Acid leaching was proposed to liberate the adsorbed rare earth elements from the bentonite clay. Accordingly, acid leaching experiments were performed to study the desorption of three commonly-found rare earth elements, namely neodymium, samarium, and dysprosium, from bentonite clay in the presence of sulphuric and hydrochloric acid. It was established that the three rare earth element species could be selectively removed as a group from iron, magnesium, and manganese metals through the careful manipulation of the pH. An investigation into the kinetic aspects of the rare earth element desorption process from the bentonite clay was also undertaken. The applicability of various kinetic models such as zero-order, pseudo first-order, pseudo second-order, elovich, parabolic diffusion, and power function were tested to describe the time-dependent desorption of rare earth elements from bentonite clay. It was determined that the pseudo second-order kinetic model represented the dissolution processes for neodymium, samarium, and dysprosium from bentonite clay the most accurately.

Jan 1, 2012

By Ross R

Although mining is an old industry its management is quite a new science, and its complications are now being recognised as demanding expert knowledge in many branches of technical and professional education. Not the least amongst these isaccountancy, for probably its most important problem is "How to control the expenditure." Unlike most businesses a mining company stands almost entirely in the light of a purchaser in the world's markets, and not as a seller, except say for product so the established and perfected systems of modern industries cannot be adopted for mining purposes. For this reason it has been left for late years to consider the matter seriously, and now a number of well-managed concerns have devised costs systems to suit their own requirements.Very little, however, has been published and even that is disjoined and difficult to make use of. Some of the costs systems in vogue, although elaborate and imposing, are not of very great value for keeping check on wasteful expenditure, or for displaying the commercial effect brought about 'by any particular change in practice, or by an addition or alteration to a portion of existing plant.

Jan 1, 1912

The Round Hill gold-scheelite deposit is located three kilometres from Macraes Flat and approximately 60 kilometres due north of Dunedin, New Zealand. A mining feasibility study is currently being undertaken on the deposit by BHP Minerals (New Zealand) Limited, who are the managers and operators of a Joint Venture with Home Reef Mining Limited. BHP has a 70 per cent equity in the project area.

Jan 1, 1987

By D. M. A. Flight, G. E. M Hall, P. R. Simpson

theoretical viewpoints.

Apr 1, 1994

The theme of this Conference is 'The Future of Mining in New Zealand' to be addressed at a time of deepening economic concern. To ensure the assessment and development of our mineral resources in a competitive, safe and environmentally acceptable way a modest supply of a rare commodity û the professional mining engineer û must be assured. This paper briefly' reviews the history of mining education in New Zealand, discusses relevant overseas academic concerns and actions and discusses recent local trends which have led to a most serious recruitment position in the Department of Mining Engineering at the University of Auckland. Conclusions are drawn and proposals made which may remedy this situation which could have serious economic and sociological consequences for New Zealand.

Jan 1, 1991

By J. E. Nesset, S. R. Rao, J. A. Finch

"For base metal sulphides, iron rejection starts in mineral processing. This review focuses on changes in plant practice specifically to improve iron sulphide rejection by control of contaminant ion effects and discusses selected general innovations in mineral processing that can be expected to play a role. One group of changes to control contaminant ions is in size reduction (the use of stage grinding and inert stirred milling) and another is in system chemistry (order of reagent addition and exploitation of the flexibility of sulphoxy reagents). Plant examples illustrate the successes, indicating that there are several options available. The general innovations start by considering the new tools for measuring gas dispersion properties and quantifying froth characteristics by imaging. Examples of their application to improve concentrate quality illustrate the potential. Other innovations stress adapting geostatistics to model variation in milling and flotation response to provide feed forward control and rigorous application of statistical experimental methodology in plant test work. An example from one concentrator shows improvements in concentrate quality from application of basic principles can be impressive.INTRODUCTIONThe more iron control (rejection) that can be accomplished in mineral processing the lower the subsequent metal extraction costs and environmental implications of iron disposal, particularly in hydrometallurgical processes. Iron rejection has been a contributing target to periodic attempts to apply mineral processing to nickel laterites and bauxites but the prime application is control of pyrite and pyrrhotite (iron sulphides) in the treatment of sulphide ores by flotation. In this paper some new concepts and innovations introduced in sulphide flotation plants over the past ten years or so (i.e., since a previous review [1]) will be outlined with examples of how they have contributed to improved “iron control”.To increase rejection of iron minerals, first the recovery mechanism should be understood. There are four principal ones, two physical in origin: 1, via locked particles (i.e., flotation of composite particles due to insufficient size reduction to liberate the minerals) and 2, through entrainment in the water reporting to the float product (an unselective process); and two originating from a response to the system chemistry: 1, true flotation (i.e., iron sulphides becoming hydrophobic) and 2, as a result of iron sulphides forming aggregates with hydrophobic particles (e.g., ”slime” coatings). There has been considerable effort to diagnose which of these dominates iron sulphide recovery; in many cases it is due to “chemistry”, in particular true flotation. The flotation effect often appears related to contamination by metal ions [1]. This can reduce selectivity in two ways: 1, metal ion species may activate iron sulphides, or 2, cause general depression which demands more vigorous flotation conditions (e.g., additional collector) with consequent loss of selectivity. This is where the review will start, by considering ways to control contaminant ions."

Jan 1, 2007

By Victor Nazimko

A new technique for reaming the holes has been tested. This technique is available for reaming a hole at its deep end creating an enlarged cavity that has helicoidal grooves oriented at less than 40 degrees to the hole axis. This technique increases bolt resistance by a factor 1.3-1.62; its bearing capacity by 3 times and enhances underground roadway stability. This technique is suitable for great depth (1000m and greater) and weak wet rocks.

Jan 1, 2008

By G. Danko, R. Tiwari, J. Knowles

Many excavation and loading tasks require equipment operators to simultaneously coordinate the motion of multiple machine links, in order to achieve complex tool trajectories. Efficiency, ore selectivity, and machine wear, are all affected by the skill level and attentiveness of the operator. A software-based kinematics reconfiguration system designed to assist operators with various tasks has been implemented on a small experimental excavator using our new differential control architecture. Kinematics transformation and feedback control algorithms are being developed and tested using computer simulation, and the results implemented on the experimental excavator. Several task-specific kinematics transformations, including a virtual revolute-to-Cartesian machine reconfiguration and computer-assisted bucket steering and stabilization have been successfully tested. Progress, challenges, results, expected benefits, and planned work are described.

Jan 1, 2006