Search Documents

The mineralogy and microstructure of mattes from the nickel flash smelter at Kalgoorlie, Western Australia, have been studied. The flash furnace matte consisted mainly of an intimate mixture of pentlandite and heazlewoodite with some nickel metal. The electric furnace matte was mainly an iron-nickel alloy with subsidiary pentlandite while the converter matte consisted mainly of heazlewoodite with crystals of nickel metal.

Jan 1, 1977

By David C. Kraft

Helical piles and ground anchors were used to meet critical design and constructability requirements for an urban forest Canopy Walk at the Atlanta Botanical Garden, Atlanta, GA. The 12-foot wide pedestrian walkway path was to be nestled among the treetops of a forest, extending to 600 ft. in length, and soaring 40 ft. high above the forest floor. Of particular concern during construction was that the foundation system for the temporary steel shoring system had to be non-invasive to the subsoil, could not damage the forest floor, trees, root systems, or foliage, and upon completion of the concrete walkway pour, could be removed, again without disturbing the subsoil. Accubrace, Inc. designed and installed all the helical foundation types, as well as provided steel braces, typically used in Tilt-Up building construction, for the walkway project. The braces, some extending to 43 ft. in length, were used to provide lateral support against wind loads for the walkway form. In addition, the braces acted as secondary support for lateral loads during the placement of wet concrete along the 600 ft. length of the walkway. Helical foundation products installed included vertical compression piles, ground anchors for tension rods, and ground anchors for the braces. The installation of the piles and anchors was particularly challenging since the forest floor elevation varied as much as 50 ft. due to the presence of a ravine. Information is provided on the subsoil conditions, required loads, design, installation, and acceptance criteria for each helical product type installed for the project. The results of vertical and lateral load tests on the helical piles in the pre-construction phase, conducted in conformance to project specifications are presented. Photographs to illustrate the nature and complexity of the project are included. The concrete pour for the walkway was successfully completed on December 12, 2009, and the walkway was opened for visitors in May, 2010.

Jan 1, 2011

By E. V. Lilford

A number of countries have introduced codes governing the valuation of mineral assets and securities. The African continent will follow suit in due course considering the importance of the global minerals industry as it relates to the attraction of foreign investment. South Africa is to introduce the Petroleum and Minerals Development Bill legislating the involvement of previously disadvantaged individuals and communities in the country?s minerals industry. One of the challenges facing the successful implementation of such codes and bills lies with the abilities of independent valuators to value mineral properties and projects on a consistent basis. Certain valuation principles and methodologies are applicable in all jurisdictions in the minerals industry. These valuation tools and principles are considered and developed in this report. They have been discussed and developed to encourage minerals valuators to consider and consistently apply the most applicable valuation methodologies.

Jan 1, 2002

By Roozbeh Afzali

Designing an appropriate tunnel blasting pattern reduces the cost of rock breakage and subsequent operations such as loading, haulage and support of tunnels. For that reason, we developed a software that designs tunnel blasting patterns. Using this software, three different tunnel blast design models based on parallel hole cut, namely, Swedish, Konya and Energy Balance, were investigated and compared for a virtual tunnel. Accordingly, blasting patterns were designed, for different cross sections. The trend of parameters such as specific charge and specific drilling as functions of tunnel cross-section was determined for each model. Our results show that, in general, The Swedish model gives lower specific charge and specific drilling compared to other models.

Jan 1, 2008

By Tellis D. A

An outline is given of the general position of earthsciences information in Australia, the background to development of the Australian Earth Sciences Information System (AESIS) and the role of the Australian Mineral Foundation in developing and co-ordinating the projeot in co-operation with the CSIRO, BMR, National Library of Australia, AGIA, and many companies.Details 'of the system, method and anticipated rate of input (especially of unpublished material at which the System particularly aims), mode of dissemination, and use of the data base are discussed. Information on theAustralian Thesaurus of Earth Sciences and Related Terms and brief details of some 30 earth sciences information collections in Australia is given.

Jan 1, 1977

By Jim Bruce

The Transformation AGO project, constructed between 2005 and 2008, featured a foundation trade contract that included design of pile caps and grade beams and construction of 138 permanent micropiles. The new foundation works were constructed within seven different settings ? each featuring a host of attributes challenging to constructability ? inside and outside the existing Art Gallery of Ontario, all while the gallery remained open for business. Transformation AGO resulted in several firsts for micropiles in the Toronto construction market: this was the first micropile trade contract with a multimillion dollar contract value; it featured the first static compressive load test performed beyond 7000 kN on a single micropile; the first static compressive load test beyond 8000 kN on an experimental pile cap supported by two test micropiles; and it was the first publicly funded project to go to tender with micropiles listed as the preferred foundation option. This paper outlines the successful application of micropiles at the landmark Transformation AGO project.

Jan 1, 2011

By C. Carrasco

"Over the last 30 years the average grade of mined ore bodies has significantly decreased while the proportion of waste removal has in many cases more than doubled. This has been identified as prime reason of a major increase in energy consumption and decrease in productivity across mining operation. Metal coarse preconcentration of ROM feed grades by size rejects low grade gangue/waste material in the size range of 10-100 mm prior to grinding, typically before primary crushing. This relies on propensity of metal to preferentially deport in the fine size fractions after breakage. Metal preconcentration by size has the potential to increase energy efficiency and therefore improve mining productivity on unit of metal basis. Results of an extensive belt cut sampling campaign conducted at a major Australian Au-Cu mine operation show that for some samples between 90% of Au and 80% of Cu is in 40% of the mass at -50 mm fraction. This indicates that low grade coarse material can be removed from the circuit, doubling feed grade at half of the tonnage and therefore improve energy efficiency per unit metal produced. This response, however presents significant variability in the same order as other processing attributes such as impact hardness and flotation recovery. This has led to development of geometallurgical laboratory tests using blast hole chips and drill core facilitating mapping and population of coarse metal preconcentration signatures in long term resources and short term production models. Preferential Cu deportment by size at drilling scale can be recognised, however scales up factors are required to transform laboratory results to production responses. At 50 % of mass the drilling products underestimate the belt cut responses by 20-30 %. Bulk sampling campaign with blast hole and drill core samples spatially related was also conducted to investigate in more detail the difference between production scale and drilling scale preconcentration responses."

Jan 1, 2014

By K. A. Lapakko, D. A. Antonson

Fourteen samples of pyrite-bearing Archean greenstone rock (d < 6.35 mm, 0.04% < St < 1.22%) were characterized (particle size, chemistry, mineralogy) and subjected to laboratory dissolution testing. The only sulfide and carbonate minerals identified were pyrite and siderite, respectively. Quartz, chlorite and sericite typically comprised 90 to 98 percent of the mineral content. For the first 60 weeks, seven samples with sulfur contents less than or equal to 0.16% produced drainage pH values exceeding 6.0. Over this period, six of the seven samples with sulfur contents greater than or equal to 0.20% produced drainage pH below 6.0, with minimum values ranging from 3.2 to 4.7. The seventh sample (0.72% S) had a siderite content of 18%. Small amounts of magnesium and, to a lesser degree, calcium carbonates present in the siderite apparently dissolved to neutralize acid and maintain drainage pH above 6.0. Sulfate release rates generally increased as sulfur content increased, and the rates of pyrite oxidation estimated for individual samples were roughly half to five times that reported in the literature for the abiotic oxidation of pyrite by oxygen. Observed neutralization potentials ranged from 0.2 to 2.0 g CaCO3/g rock.

Jan 1, 2002

By John Gamble

This paper summarizes the weight of epidemiological evidence to evaluate the hypothesis that asbestos exposure is causally associated with increased risk of gastrointestinal (GI) cancers as suggested by Selikoff in an early study of insulation workers. This review looks at populations that develop GI cancers, namely stomach, colorectal, colon and rectal. Guidelines for assessing causality are strength of association, biological gradient and consistency of the associations. Exposure?response (E?R) was evaluated using three methods to estimate exposure. Rate Ratios (RRs) for lung cancer and percent of mesothelioma are used as surrogate measures of asbestos exposure for all the cohorts of exposed workers. Quantitative or semi-quantitative estimates of cumulative exposure to asbestos were also used to assess E?R trends and were compared to E?R trends for lung cancer and mesothelioma in individual studies. Surrogate measures are important since there are few individual studies that have assessed E?R. None of the various methods to estimate asbestos exposure yielded consistent E?R trends and the strength of the associations were consistently weak or non-existent for the four types of GI cancers. The epidemiological evidence detracts from the hypothesis that occupational asbestos exposure increases the risk of stomach, colorectal, colon, and rectal cancer. Findings are briefly summarized below. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestos; Colon cancer; Colorectal cancer; Gastrointestinal cancers; Ingestion; Lung cancer; Mesothelioma; Rectal cancer; Review; Stomach cancer

Jan 1, 2007

By G. D. Bakulev

Economic Importance of Gasification of Fuel and Brief Outline of Development of Underground Gasification of Coal in the U.S.S.R. The underground gasification of fuel offers a number of economic and social advantages, principally the following: 1. Full automation of labor-consuming coal-mining processes, which resist complex mechanization and automation, particularly shaft mining. 2. Elimination of hard, dangerous, and often unhealthful mining work. 3. Creation of hygienic conditions for personnel employed in gas production, as well as for those in boiler rooms using the gas. 4. Possibility of automation of complex production processes of thermal-electric powerplants using underground gas with economic installations for steam production. 5. Economic operation of thermal-electric powerplants constructed in the areas of underground-gas production. 6. Release of railroads from the burden of transporting fuel. 7. Extension of the power base of some areas in need of fuel and of the economy as a whole due to use of fuel deposits not amenable to normal mining practices. 8. Reduction of capital investments per unit of energy produced in the form of fuel. 9. Substantial increase in general labor productivity. 10. Possibility of substantial reduction in the cost of fuel produced and of electric power produced from underground gas.

Jan 1, 1962

By Michael Alber

Resin grouted rock bolts are the major support measure in coal mining. They are rather easy and foolproof to install, take immediately load and are the least time consuming support measure for controlling gateroad deformation. The use of only resin grouted bolts allows fast gateroad development which is essential for economical resource exploitation. The design of reinforcement / support systems for coal mining typically bases on empirical methods, which work fine when encountering known or usual ground conditions. However, coal mining approaches depths where little experience exists and numerical modeling is often the only method to estimate ground behavior. This paper discusses the geotechnical properties relevant to numerical model and focuses particularly on input values for modeling resin grouted rock bolts for safe gate design.

Jan 1, 2006

By Felix du Breuil

Contract H0177044 included three objectives; (1) consolidate, maintain, and distribute information on STE approved lighting systems; (2) develop and present one-day seminars on underground mine lighting; (3) determine direct labor and hardware costs associated with the installation of mine illumination systems. All objectives were completed with results as follows: Task I - A file containing 1350 Statements of Test and Evaluation (STE) for all types of underground equipment was developed and publicized throughout the coal fields, A total of 40 requests for STE information was received and processed. Task II and III - A series of 50 seminars was scheduled and presented to 942 attendees throughout the coal fields. The seminars were well received and attendees indicated the information presented would be helpful in bringing their equipment into compliance. Holding a series of seminars in the coal fields, instead of a few in population centers, was favored by attendees. Task IV - Installation cost data obtained on 415 lighting systems indicate that the factors which most affect installation costs are higher hardware cost for DC powered systems and slightly higher manpower requirements for systems installed underground. Based on these data, the total cost to industry of retrofitting existing underground equipment could range up to $50 million.

Jan 1, 1979

By Edward J. Caldwell

In 1930 the Bureau of Mines published a description3/ f the concentrating process of the Magma Copper Co. as it had been developed to that time and was then employed. The prevent paper revises the description to the end of 1943 and includes a description of the smelting processes. Data from the mild and smelter operations for, 1942 are given in tables 1 to 14, Billing costs are included, but it is not permissible to publish smelter costs.

Jan 1, 1944

By Bohrn W, Milionis K, Tessmer G, Reidetschlager J

The share of electric arc furnace based steel production is increasing - New technologies for the production of virgin raw materials for EAF production are under development and on the market - VAI has a strong position in the field of scrap substitution technologies with their COREX«-, COREX«-DR and FINMET«-technology. In late-1998 the steel plant SALDANHA was started up successfully. This integrated compact mill is using the COREX«-technology as hot metal and a combined DR-plant as DRI production unit. Also in 1999 the BHB FINMET« plant Port Headland went on Stream.

Jan 1, 1999

By Hargraves A. J

With increasing depth, stresses and stress phenomena are becoming more important considerations in Australian coal mining.A large number of compressive and tensile strength tests was made on coal and rock cubes cut from samples taken in various Australian collieries. In addition, an empirical impact strength test was carriedout on fragments of the same samples, to obtain a correlation with compressive strength.In one colliery, flat-jack measurements were taken to assess stresses in coal ribs and in the roof.INTRODUCTIONBy world standards, some of the New South Wales collieries are approaching depths of cover considered a maximum for bord and pillar the normal Australian coal mining method. Several South Coast collieries are winning coal at depths of about 1500 ft., and future operations are being planned at deeper cover. Some areas of these deep workings produce considerable quantities of seam gas.Phenomena associated with high stress and copious gas under pressure in the seam violent phenoma presenting a danger and a nuisance in mine working - have occasionally occurred, and the phenomena are being investigated as a whole (Hargraves, 1958), and separately as a gas problem (Bolt and Innes, 1959; Hargraves, 1962) and as a stress problem. This paper relates to the latter - to investigations into the strengths of coals and coal measure rocks, and into the stresses in and about coal seams...

Jan 1, 1962

By R. Katzenbach, M. Vogler, U. Adamietz

Abstract The design of deep excavation pits in rock mass is dependent as well on the mechanical properties of the rock mass as for example the orientation and the type of discontinuities like bedding planes, joints and fissures, the length of the discontinuities (persistence), the grade of weathering, the strength of rock mass, and the shear strength in the discontinuities, etc., and also on the respective boundary conditions specific for the project, and here especially the geometrical boundary conditions. The basic mutual influences and interactions between these boundary conditions are explained and exemplary presented at an excavation pit with a depth of 18,5 m, situated at a slope with a surface near groundwater table. Résumé La planification des excavations profondes dépend aussi bien de la qualité mécanique du roc, par exemple la location de la texture de la surface de moindre résistance, le degré de rupture, le degré de décomposition, la dureté du roc et la résistance limitée au cisaillement de la texture de la surface de moindre résistance que des conditions limitées spécifiques pour le projet, ici en particulier des conditions limitées géométriques. Les influences et interactions essentielles et mutuelles entre les conditions limitées isolées seront expliquées et présentées à l’aide d’une excavation 18,5 m de profondeur, située sur une pente où le niveau des eaux souterraines est près de la surface. Kurzfassung Die Planung tiefer Baugruben im Fels hängt sowohl von den mechanischen Eigenschaften des Fels wie z.B. der räumlichen Lage des Trennflächengefüges, dem Durchtrennungsgrad, dem Verwitterungsgrad, der Gesteinsfestigkeit sowie der Scherfestigkeit des Trennflächengefüges als auch von den projektspezifischen Randbedingungen hier insbesondere von den geometrischen Randbedingungen ab. Die wesentlichen gegenseitigen Einflüsse und Interaktionen zwischen den einzelnen Randbedingungen werden aufgezeigt und an einer 18,5 m tiefen Baugrube in Hanglage mit oberflächennahem Grundwasser vorgestellt.

Jan 1, 2003

By Z. T. Bieniawski, E. H. Skinner, R. A. Cummings, F. S. Kendorski

INTRODUCTION Caving Mine Drift Support Design The support of production drifts remains a high-cost item facing the developer or operator of an underground caving mine. Support costs are incurred well in advance of ore production, and there is a strong need to minimize these pre-production commitments of capital. Due to the extensive rock loads that normally develop during the caving process, the support used in caving mines is typically quite heavy and therefore costly. The process of designing this support increasingly makes use of basic tunneling principles, but is hindered by the still-incomplete state of knowledge of rock behavior in caving mines, and high variability of geological conditions in caving orebodies. Caving mines differ from tunnels in that the deformations and rock loads induced are transient and dynamic in occurrence, and are normally large in magnitude, often well in excess of rock mass strength. As opposed to tunnels, caving mine layouts are more intricate, and the methods and effects of construction ordinarily are not as closely monitored. Safety factors in mining tend to be lower and rock masses tend to he weaker. These aspects prevent strict application of tunnel design technology to caving mine drift support, with the result that mine drift supports are commonly designed chiefly on the basis of experience at other mines. Mining procedures at caving mines are evolved in response to site-specific requirements, to the extent that there are really as many caving methods as there are caving mines.

Jan 1, 1983

By Donald E. Raab, Lee W. Saperstein

INTRODUCTION The Premise Not much time has to be spent in a tunneling project to realize the tremendous interdependence that exists among the various unit operations. The research that is to be described attempts to examine one set of these linked operations, namely, the effect of cutters on muck handling properties. All too often research focuses on too minute an aspect of a problem for the results to be of much immediate, practical use. The goal of this research is to avoid this specificity. Apologies are tendered if this goal is missed. It is known that the mode of flow of bulk solids under the influence of gravity -- emptying a bin or hopper -- is dependent on several basic parameters. The size of the particles and the distribution of sizes (consist) determine whether the solids will first flow out of a given aperture; the cohesion of the solids will determine if flow will continue after the bin is opened; and the angle of internal friction determines the size of the flow regime (1,2,3). It is well understood that the latter two parameters affect the behavior of bulk material on a conveyor belt. Cohesion of material to a belt is always an undesired problem. Heaping of material on a belt depends on the material&apos;s internal friction. It is also known that varying the particle size, and the packing density of the material can affect the material&apos;s angle of internal friction (4,5). The question was posed whether sufficient variation in a mechanical tunneling machine&apos;s (mole) cutting function could be arranged to affect materially the handling properties of the muck

Jan 1, 1974

By J. Moore, D. Gault, R. V. Lugn

Impact of small projectiles with velocities between 0.9 and 7.3 km per sec on basalt produce craters chiefly by the ejection of fragments. Weight-size distributions of the ejecta are linear for part of the size range of the fragments. Cumulative weight-size distributions of the ejecta from different craters vary because of erratic formation of large fragments and a large percentage of ejecta below 0.1 mm. In the range of velocities studied, the crater depth is approximately proportional to the 0.75 power of velocity of the projectile. This relationship may represent a transition regime between the fluid impact regime and the undeformed projectile impact regime. The volumes per unit of projectile energy of the craters produced are comparable to those reported for lower speed projectile impact and drill bits. An experimental investigation of projectile impact on rock is being conducted jointly by the Ames Research Center of the National Aeronautics and Space Administration and the U.S. Geological Survey. Projectiles are launched with light-gas guns at the Ballistics Range of the Ames Research Center. The craters and ejecta produced in these experiments are being studied by the U.S. Geological Survey. Steel, aluminum and polyethylene projectiles weighing from 0.25 to 0.015 g were accelerated to velocities of 0.88 km per sec (2,900 fps) to 7.3 km per sec (24,000 fps) with a light-gas gun, using hydrogen as the propellant medium. Projectiles impacted the targets normal to plane rock surfaces in an atmosphere of air with a nominal pressure of 25 to 50 mm of mercury. The metal projectiles were mounted in supporting four-piece nylon sabots, which guided the projectiles down the launching tube. After launch, aerodynamic drag acted to separate the sabots from the projectiles. Impact velocities were determined with time measurements and spark photographs of the projectiles in flight. Ejecta were collected in lucite and aluminum containers placed around the target block. A small hole in the containers permitted projectile entry. Impact of projectiles of the size employed produced craters in the rock targets chiefly by ejection of fragments. The craters are small, roughly conical depressions with crushed and intensely fractured rock at the bottoms of the depressions. The ejecta are composed of pieces of the projectile and rock fragments ranging in size from a few tenths of a micron or less to several centimeters in maximum dimension. In this paper, the structural features of the craters, the weight-size distributions of the recovered ejecta, and crater depth and crater volume relationships are described. DESCRIPTION OF CRATERS Typical craters (Fig. 1) produced by experimental projectile impact in basalt are shallow, wide base

Jan 1, 1963

By L. Kulik, J. den Drijver

Rhenish lignite will continue to play an indispensible role in the energy mix of the German Federal Republic for a long time to come. The use of lignite for electricity generation, upgrading and, if necessary, as a raw material is geared to the long term. The holistic management of opencast mines underpinned by approval law in the long term and a stronger focus on man, the environment and nature contribute to the acceptance of the mines by the local population. The same is true of state-of-the-art lignite uses: as regards their operational flexibility, lignite-fired power plants are ideal partners for the expansion of renewables. It is along these lines that RWE is continuing its power plant renewal programme as planned. With a view to that which will be conceivable the day after tomorrow, RWE is researching future technologies today in order to meet objectives such as security of supply, profitability and environmental compatibility to the same extent in the long term. Another important contribution to acceptance is public transparency and communications as means to support approval procedures and the implementation of measures in all areas related to lignite mining and utilization.

Jan 1, 2011