Search Documents

By Walter R. Storms

"INTRODUCTION The New Mexico potash exploration described herein was begun in February 1944 with the object of determining the amount of potash ore in the United States Potash Reserve in Eddy County by exploring the deposit from the surface with vertical drill holes. The work was completed in October of the same year after 16 holes had been drilled on the Reserve and in the immediate vicinity.The Potash Reserve is in secs. 26; 27, 34, and 35, T. 20 S., R. 29 E., Eddy County, N. Mex., about 14 miles northeast of Carlsbad, as shown on figures 1 and 1A, Drilling was done in secs. 26 and 35 of the Reserve, in section 14 to the north, end sections 2 and 56 to the east. All work was done on Governnent-owned, unleased land.The Reserve may be reached from Carlsbad by traveling to the north-east by automobile for about 14 miles on the paved U. S. highway 62. This highway passes through the southern part of the Reserve. Other parts may be reached by a State highway that passes along the eastern side of the area, then by poor dirt roads to various drilling sites. A branch of the Santa Fe Railroad also passes across the southern part of the Reserve enroute from Carlsbad to the plant and mine of the Potash Co. of America, a few miles northeast of the project and 22 miles from Carlsbad."

Aug 1, 1947

Currently raw brown coal is fired in the Latrotx; 'ahcc th,iki~, Lanying with it two major penalties, (a) boiler efficiency of 65 - 70 per cent (in terms of GCV), (b) much higher boiler cost than for black coal. Drying the coal, in energy-efficient, and cost-efficient manner, opens the way to efficiencies of order 88 per cent and enables the lower cost black coal type boilers to be used. With the higher boiler efficiency goes much higher combustion temperatures and the effect of this on radiative heat transfer is a major factor in reducing boiler cost. In a fluidised-bed combustor the temperature is controlled to 800C - 900C. In a pulverised fuel combustor higher temperatures are however achieved and can increase boiler fouling due to the salt content of the coal. This is a problem which needs to be solved. Victoria has the prospect of lifting efficiency from 28/29 per cent to 35 per cent, of reducing carbon dioxide output correspondingly and reducing cost of power stations. So far as gasification is concerned, efficient removal of liquid water from the coal is important to the overall efficiency.

Jan 1, 1992

By J. D. Findlay

The demands on development in London in recent years has led to the increasing use of top down construction methods in which there is a requirement to place steel columns to high tolerances into large diameter bored piles with deep cut-offs. A number of different proposals for the sequence of construction are being suggested. The tolerances requires for the steel columns are becoming increasingly stringent. This review examines a number of basic construction proposals and comments on the problems and solutions used by foundation contractors to provide the required foundations.

Jan 1, 1989

By D. Brand

"The risk management objective of the AMIRA Code of Practice for Metal Accounting has seldom been systematically investigated in the literature up to the authors’ knowledge. Risk is defined in the Australian Standard on Risk Management (AS/NZS 4360:2004), as “the chance of something happening that will have an impact on objectives”. The simplified economic analysis performed in this paper has lead to define “something happening” as measurement non-representativity and “impact on objectives” as NSR loss from the optimal NSR. This has pinpointed a missing link being the establishment of a relation between NSR in flotation plants and measurement representativity. The proposed framework, referred to as the total cost of representativity, answers the previously unanswered question of how much accuracy/reproducibility is fit for purpose in a given flotation plant. Authors readily acknowledge that it is way easier to assess the cost of accuracy/reproducibility than the cost of inaccuracy/irreproducibility. However, this exercise not only answers previously unanswered questions but also establishes an essential link with operational excellence. This paper exposes why such operational excellence could neither be attained nor proved without a state of the art metal accounting system. This should impact not only how metal accounting systems are audited/designed/refactored, but also how flotation plants are designed.IntroductionBecause representative metal accounting is a vital source of information for the financial accounts of a mining/metallurgical company, the need for a code on metal accounting was recognized in 2001 and a team was formed in 2003, under the sponsorship of several major mining houses, to produce such a code. Table 1 exposes the two main objectives of this AMIRA Code of Practice for Metal Accounting."

Jan 1, 2017

By Murray W. Hitzman

Two great revolutions in mining occurred during the 20th century. The first took place almost 100 years ago (1903-1905) with Daniel Jackling’s experiment in the economies of scale for large-scale mining at Bingham Canyon. Jackling’s ideas changed the focus of base metal exploration toward lower-grade, high-tonnage deposits. The second revolution was the impact of environmental and social concerns on mining. It started near the end of the 20th century and is still under way. This article speculates on the effects of this second revolution on the future of mineral exploration.

Jan 1, 2005

By L. D. Patts, G. H. Schnakenberg

Achieving substantial reductions in the exposure of underground miners to diesel particulate matter in a number of metal and nonmetal mines in the U.S. depends on the ability of the industry to widely implement advanced diesel emissions control technologies, primarily diesel particulate filter (DPF) systems. Recent field studies showed that diesel particulate filter systems with Cordierite and silicon carbide ceramic filter elements are capable of reducing concentrations of diesel particulate matter and elemental carbon by more than 70 and 90 percent, respectively. But those studies and several other attempts to implement DPF systems in underground mines revealed a number of relatively unique technical and operational challenges that are limiting industry-wide implementation of this technology. This paper provides detailed analysis of some of those challenges and short overviews of several projects launched by NIOSH Pittsburgh Research Laboratory in an attempt to provide the underground mining industry with more adequate DPF systems. These systems employ advanced technologies to overcome the most pronounced challenge, the regeneration of DPF elements installed on mining engines that generate relatively low exhaust temperature. This paper presents essential findings obtained through a long-term evaluation of DPF system with diesel fuel burner technology installed on a heavy-duty load-haul dump vehicle in an underground metal mine. In addition, the essential results of the laboratory evaluation of a popular on-highway DPF system which was adapted and optimized for underground mining applications will be summarized in this paper.

The maximum current density at which conventional copper electrowinning plants will result in satisfactory, adherent, and dendrite·free cathodes is determined by the thickness of the diffusion boundary layer. A decrease in the value of that thickness will permit an increase in the current density. This fact is utilized to develop a high current density cell in which the reduction of the boundary layer thickness is accomplished by means of a specially designed electrolyte circulation system. The high current density cell is used to determine the effect of current density on such process parameters as current efficiency, cell voltage, power consumption, and cathode purity. A number of empirical equations are developed for the purpose of estimating the magnitude of these effects.

Jan 1, 1972

By John S. Ball

[A system of analysis for sulfur groups in petroleum distillates has been developed as one phase of the Bureau-of Mines investigation of the more economic utilization of the so-called "black oils" of Wyoming. This problem is being studied by the Bureau of Mines under a cooperative agreement with the University of Wyoming at the Bureau's Petroleum Experiment Station , Laramie, Wyo. Wyoming black oils have high sulfur and asphalt content and usually yield only small percentages of straight-run gasoline. A more detailed description of the properties of black oils has been given in a previous publication (3)3/. The preparation and properties of asphalts from those oils have been described (1, 2), and the effect of thermal cracking and the use of ordinary methods of treating wore discussed in one Bureau publication (4), Although these studies gave considerable insight into the properties and characteristics of black- oils; it was thought t that a more fundamental attack would assist-materially in, the problem of sulfur removal.]

Jan 1, 1941

By John S. Ball

[A system of analysis for sulfur groups in petroleum distillates has been developed as one phase of the Bureau-of Nines investigation of the more economic utilization of the so-called "black oils" of Wyoming,. This problem is being studied by the Bureau of Nines under a cooperative agreement with the University of Wyoming at the Bureau's Petroleum Experiment Station, Laramie, Wyo. Wyoming black oils have high sulfur and asphalt content and usually yield only small percentages of straight-run gasoline. A more detailed description of the properties of black oilshas been given in a previous publication (3)3/. The preparation and properties of asphalts from those oils have been described (1, 2), end the effect of thermal cracking and the use of ordinary methods of treating wore discussed in one Bureau publication (4), Although these studies gave considerable insight into the properties and characteristics of black oil, it was thought t that a more fundamental attack would assist materially in the problem of sulfur removal.]

Jan 1, 1941

By Jake Hutchison, Wade Hutchison

The opposition to the project has risen as a result of some political pressures and from public perceptions about the project’s necessity and its impact on the neighborhood. As a result of this controversy, the Underground Conservation Hall was quickly termed “Bredesen’s Bunker” by the Media. Close exposures for blasting, required by the Conservation Hall construction project, have been regulated by specifications that regulate seismic monitoring, pre-blast and post-blast inspections. Planned blasting for the project included blasting to a depth of 30 feet (9.14 meters) within 35 feet (10.67 meters) of the front of the newly renovated Tennessee Executive Residence. Excavation for the project found more competent rock at higher elevations than identified in test drilling which required blasting within 2 feet (0.61 meters) of the side of the Residence.

Jan 1, 2009

By Mark H. Balfe

Over the last decade, Fenway Park has undergone annual improvements to modernize the facility for players and fans. These renovations include the Monster Seats, the Right Field Roof expansion, a new pavilion behind home plate, expansion of the Red Sox clubhouse, additional roof seating, and concourse improvements. Retrofitting the historic ballpark to bring it up to current standards required installation of foundations to support the new structural loads for each of the alteration projects. This required evaluation of existing conditions, and in many cases augmentation of the foundations at existing columns to accommodate the structural changes to the park. New foundations, generally consisting of drilled-in micropiles, were installed in numerous configurations and conditions. Since 2003, a total of 215 drilled-in micropiles have been installed to augment various columns around the park. The micropiles range in capacity between 40 and 70 tons and are installed through Fill and Organic Soils and embedded into the dense Glaciofluvial Sand and Gravel layer. Issues and learning related to the foundation augmentation include schedule constraints (work is typically conducted during the off-season and schedule is very aggressive), encountering old/abandoned utilities or foundations, ventilation of equipment, and management of spoils during micropile installation.

Jan 1, 2011

With the passing of Dr William Bleloch on 20th June 1991, we lost not only a colleague and a good friend but a man who made a very significant contribution to the industrial development of South Africa. He can rightly be called the father of the ekctrochemical and electro-metallurgical industries in this country, since his ideas and dedicated work were directly responsible for the development of these large industries as we know them today.

Jan 1, 1991

Project developent proceeds by increasingly detailed studies addressing overall project returns through an analysis of the substance, risks and costs associated with the following elements: ò Reserves ò Mining ò Processing ò Infrastructure ò Environmental Impact ò Product Market Computer-based expertise has a potential to ò Capture perishable expertise, making this available for shared access and so reducing the cost of human experience ò Consolidate know-how for optimising process operations, bringing consistency of judgement and advice to decision- making by making the rules, facts and preferences explicit ò Allow assignment of the basis and authority of decisions, so experts can pass routine expertise down the line, freeing their time to generate more. ò Force a review of expertise when creating the knowledge base.

Jan 1, 1989

By C. E. White

History The Con-Rycon mine is situated in the Yellowknife mining district, North West Territories, 608 air miles north of Edmonton, Alberta. The earliest reported discovery of gold in the area was made in 1898 but no extensive exploration occurred until 1928. The birth of Yellowknife as a mining community took place in 1934 with the staking of the Rich group and subsequent shipping of 16 tons of high grade ore. The Giant group was also among the claims staked in 1934, and later staking showed a tendency to close the gap between these two properties. In the fall of 1935, the A.Y.E. claims, situated south of the Giant group, were staked to cover a discovery of the Geological Survey of Canada and, after general release of the Survey's information, the adjoining ground was staked. These claims included the Con, Negus, Meg, and Kam groups. In 1936 four lapsed claims were re-staked as the P and G group and later acquired by Rycon Mines, Limited, controlled by the Consolidated Mining and Smelting Company of Canada, Limited. The Con and various adjacent groups owned by Cominco are now operated with the Rycon under one management. Surface trenching on the Con property started in 1936 and, during the fall and winter of 1936-37, a 60- foot 5 ft. by 9 ft. inclined prospect shaft was sunk. The encouragement provided by the shaft and diamond drilling in 1937 led to the decision to establish a mining plant, and in August, 1938, the 100-ton cyanide mill produced its first brick- the first gold brick poured in the history of the North West Territories. In November, 1938, the mill was enlarged to a 175-ton capacity and operated at this rate until 1941, when refractory ore was encountered. This situation was met by the installation of flotation and roasting units and, at the same time, the milling capacity was increased to 300 tons daily. Labour shortages and Government restrictions forced a reduction of output and in 1943 milling was suspended while mine development continued on a reduced scale throughout the war years. The present full-scale of operations was resumed in 1946 and the total production to the end of 1948 amounted to 288,853 oz. gold and 72,347 oz. silver.

Jan 1, 1949

By A. McLean, M. Iwase, K. Wakimoto, K. Katogi

For many decades control strategies have been based upon samples taken from liquid steel, molten slag and gas phase as well as from solid products. Because of recent developments in the areas of dynamic control models, artificial intelligence and expert systems, there is an increasing incentive to develop diagnostic sensors, which permit in-situ rapid determinations of concentrations of various elements in molten steel. In this paper, an overview is given on recent developments in the areas of sensors for use in ferroalloy and steel production. Particular emphasis will be given on (i) innovative application of sensors for on-line determinations of dissolved elements, Si, P, N, H and Cr in molten iron and ferroalloys, (ii) evaluation of inclusions in liquid metal and (iii) rapid determinations of slag compositions.

Jan 1, 2004

By L Teixeira, C J. Greet, P Karageorgos

Pyrite is ubiquitous within copper ores, and presents significant challenges to most operations in terms of its impact on copper sulfide concentrate grade and recovery.Samples of ore containing from 3 to 47 percent pyrite, with nominally the same chalcopyrite feed grade, were collected from a copper mine in eastern Australia for testing. The ores were ground under standard conditions using forged steel grinding media in the Magotteaux Mill® to determine the impact of increasing pyrite feed grade on the pulp chemistry of the system and subsequent rougher flotation response. Attempts were made to correlate the pulp chemical parameters (oxygen demand and EDTA extractable metal ions) with flotation behaviour to determine if one (or more) could be used as a metric to infer metallurgical behaviour.The observations made were then tested under different grinding environments (obtained using more electrochemically inert high chromium) grinding media to determine if they hold true.CITATION:Greet, C J, Karageorgos, P and Teixeira, L, 2015. The influence of pyrite on the pulp chemistry and copper flotation response of a chalcopyrite ore, in Proceedings MetPlant 2015, pp 175–187 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

The HB 2500 hydraulic breaker attachment from Atlas Copco Construction Tools features Krupp percussion technology and a service weight of 2,500 kg (5,512 lbs). This makes it ideal for demolition, tunneling, trenching, foundation work, rock mining and secondary breaking. Suitable for carriers in the 29-to 43-t (32-to 47-st) weight class, the HB 2500 accepts maximum hydraulic flow of 219 L/min (58 gpm) at 18 MPa (2,610 psi) of pressure, and delivers an impact rate of up to 550 blows per minute. The HB 2500 features PowerAdapt, a new system that automatically shuts down the breaker in the event that it receives excessive oil pressure from the carrier.

Jan 1, 2006

By Floyd Varley

In deep and highly-stressed coal mining, advanced design practices are used to minimize the potential for damaging events to occur. Despite these design efforts, the hazard of coal mine bumps can not be completely eliminated. This paper will review current and historic work practices used internationally to minimize the hazard to miners from mining in conditions which could produce a bump. These site specific work practices have a common base in monitoring for conditions which could result in a bump and application of controls to prevent the occurrence or minimize the severity of an event where miners are working. Monitoring practices range from purely observational to semi quantitative. Control methods attempt to initiate events in a controlled manner, absorb the energy of a potential event or reduce the potential for or magnitude of an event by altering the stress conditions of the mine workings. Building from the experiences of other coal fields, an empirical framework to manage the potential hazard of coal mine bumps can be developed to enhance the level of safety provided by prudent mine design.

Jan 1, 2008

As part of its research on advanced mining technology, the U.S. Bureau of Mines emphasizes studies on in situ leach mining. This research enables the Bureau to develop technical information that can allow mining companies to adopt in situ leach mining methods. Research results should help to remove the technical and economic barriers currently hindering the development of commercial in situ leach mining operations. This report contains papers summarizing results of Bureau research on various aspects of in situ leach mining. A featured topic is the cooperative field experiment of the Bureau and Santa Cruz Joint Venture in a copper deposit near Casa Grande, AZ. Discussions in-clude an overview of the entire project, cost modeling, environmental permitting, laboratory core-leaching experiments, petrographic studies, and an evaluation of the geologic structure in the region. In addition, papers describe hydrologic modeling and geophysical studies of solution flow during leaching. Preliminary geochemical modeling studies are also summarized. A final paper describes a nonionic chemical additive with potential for significantly reducing the high costs of drilling in in situ leach mining.

Jan 1, 1989

By David W. H. Ellis

This presentation will discuss over 2 dozen past, present and future oils sands projects in Alberta. The very early projects as well as the most recent along with the ones that never got off the ground and the ones in production are all included. For each, the following will be given (where known): owners, location, type (mining/SAGD/refinery), production, capital budget, spent to date, status. Some overall impacts will be discussed.

May 1, 2004