Search Documents

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX D DEVELOPMENT AND EXPERIMENTAL VERIFICATION OF ACOUSTIC SEAL CHECKER THEORY 1. Introduction In Section 7 of the report the acoustic seal checker concept was described in a general manner and the parameters which affect the signal level at the microphone were discussed briefly. In this appendix the theoretical basis will be presented and the experimental program described which permitted the extension of the theory into practice. The basic goal of the acoustic seal checker is to relate the reduction in sound pressure level to the size of the residual hole in the fly ash barrier. The smallest hole size that may be measured is determined by the signal to noise ratio, where the noise in this case includes the ambient noise in the mine, the internal microphone noise and the sound transmitted from the acoustic source via the flanking paths through corridors adjacent to the one being sealed. The latter source of noise can be discriminated against, at the expense of increased complexity of the acoustic system, by employing a pulsed source and pulse gating of the microphone signal set to accept sound via the barrier path and to reject the delayed flanking path signals. In order that the acoustic system be insensitive to precise source and microphone location and to permit assessment of system performance on an acoustic power flow basis, a broad frequency band of pseudo-random noise is emitted by the loudspeaker source. The preferred frequency range must be determined, the advantage of a directive source must be assessed, and the necessity

Jan 1, 1973

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

D. 1 Most Effective Salts A. Ammonium Phosphates Monammomium phosphate and diammonium phosphate (salts of ortho phosphoric acid) are superior to the triammonium salt in fire-resisting properties. Of these two, the monammomium salt is chemically the more stable. It is also held very retentively by a number of woods, thus reducing leaching out of the salt if exposed to water. Saturated aqueous solutions of mon- or di-ammonium phosphates have vapor preservatives corresponding to an atmospheric relative humidity of 9Z to 93 percent, the wood, will, therefore, not attract any moisture at humidities below this figure. Low concentrations (1 lb dry fire-retardant per cubic foot of the dry, treated timber) will stop flame and high concentration (5 lbs. per cubic foot) will prevent smoldering. B. Ammonium Sulphate In low concentrations ammonium sulphate has only a small effect on flame propagation, but its effect is marked when concentrations of the order of 20 percent are employed. It has no appreciable effect on smoldering. It is more corrosive to metals than are the phosphates, but is less corrosive than ammonium chloride or magnesium chloride. It is possible to leach it out of wood by prolonged and continuous action of water The vapor pressure of the saturated solution corresponds to 81 percent atmospheric humidity.

Jan 1, 1976

Engineering controls for overburden drilling include dry dust collection systems, wet dust suppression systems, and enclosed cabs [Zimmer and Lueck 1986; Volkwein et al. 1979]. Proper maintenance of the dust suppression system is critically important for drills using dry dust suppression methods. Failure to rigorously maintain these systems will result in inadequate dust control. Acute silicosis has been reported in miners operating equipment that relies on dry dust suppression [NOSH 1992].

Jan 1, 1997

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

TEST DECK – ALTMETER SURVEY WITHOUT PLTTMETER TEMPERATURE CCRRECTION DATA INPUT

Jan 1, 1977

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

INTRODUCTION The majority of ground water flow models have been developed for large computer systems. Most of these operate under a batch mode of operation, that is, the data are input with a deck of punched cards. The advent of micro- and minicomputers over the last few years opens the possibility of adapting many of these large flow programs to the smaller computers. In general, this adaptation will require more computer time to run the program, but in many cases if the small computer is in-house, the overall cost may be less than that required for a large computer. There are also a number of peripheral devices that can be used to make the data input much easier. As an example, the use of a digitizer with a finite element or finite difference mesh reduces the data input time considerably; the use of a graphics terminal for display of the mesh immediately after it is developed shows immediately whether there are errors in the location of node points. DEVELOPMENT OF AN INTERACTIVE SYSTEM The finite element program, UNSAT2, has been used over the past several years by the authors for several ground water flow problems (Bloomsburg, 1977; Bloomsburg and Wells, 1978; Zahl and Bloomsburg, 1980). In the past these programs have been run on an IBM 370/ 145 computer under the batch mode of operation. One difficulty that has been encountered has been in determining the length of time step that must be specified for operation of the program. The problem is that if the time steps are too large, the program becomes un- stable and operation ceases. If this happens in the middle of the problem, the only alternative is to reduce the length of time step and repeat the entire run. This problem has been alleviated in other pro- grams by using a subroutine that determines the time step automatically. If the solution becomes unstable, the time step is reduced automatically and that portion of the solution is repeated. With an interactive system this can be done by storing the output pressures and restarting the program with the new output pressures. Under the batch mode of operation, there is an option in UNSAT2 that allows restarting of the program from the last point of solution, but this must be specified when originally starting the program. The interactive computer system that we use currently consists of a PDP 1 1 /23 with hard disk drive, CRT terminal, plotter, graphics terminal, digitizer, and printer. The computer has 256 K bytes of core storage and the hard disk drive will accept a 5.2 M byte disk. To run a large program on a computer such as this, some overlaying must occur; that is, subroutines are stored on disk and put into core storage only when they are actually needed for running the program. UNSAT2 required very few changes to run on this computer but some changes were necessary to take advantage of the interactive capabilities of the system. One of these changes consists of the development of a program called DBUILD to build the data file for running the program. This program calls for each piece of data by prompt statement and gives instructions for using the digitizer. The data are then entered in completely unformated form. The node points must be entered in order and the coordinates are determined automatically by the digitizer. The pressure readings or initial conditions on each node point are entered through the terminal. All element information also is entered through the terminal. After DBUILD is run the mesh may be displayed immediately on the graphics scope whereupon any error in node point

Jan 1, 1986

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX E EQUIPMENT USED FOR FIELD TESTING OF MINE SEALING SYSTEM I. Drilling Operation - Equipment supplied by local drilling contractor 1. Mobile drill rig. 2. Flat bed truck, containing 20 lengths of drill pipe. 3. Auxiliary compressor. 4. Pickup truck for small parts and supply of diesel fuel. 5. Bulldozer. 6. Water supply, in this case the nearby stream. 7. Supply of casing, positioned next to the drill rig. 8. Ready mixed cement grout. 9. Drill bits, stabilizer units, cutting and welding equipment, other miscellaneous tools and supplies. II. Sonar Probing Operation 1. 25 foot tower with pulley mounted atop. - FMA 2. Electric winch with 100 feet of 1/4-inch cable, Model No. 100A, City Engineering Co. , Indianapolis, Indiana. 3. 400 feet of 1-1/2-inch-diameter aluminum pipe with alignment holes and coupling grooves. - FMA*

Jan 1, 1973

[ ]

Jan 1, 1997

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

THIS PROGRAM TRANSFORMS FREE FORHATED BRANCH DATA INTO A FORMAT SUITABLE FOR INPUT TO THE PENNSYLVANIA STATE UNIVERSITY MINE VENTILATION SIMULATOR (PSU/HVS 1. BRANCH RESISTANCES ARE ASSUMED TO HAVE BEEN ALREADY CALCULATED, IIOWEVER THIS PROGRAM CAN BE EASILY MODIFIED TO HANDLE THE ADDITIONAL INPUT DATA REQUIRED FOR RESISTANCE CALCULATIONS IN THE PSU/MVSO THE PROGRAM IS WRITTEN IN FORTRAN IV WITH WATFIV.

Jan 1, 1977

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

APPENDIX G TABLE IX MINE A 1 General Total Employees 3000 Maximum No, of Men Underground/Shift 800 Shifts/Day 3 Type of Ore Copper Daily Production (TPD) 25,000 Mining Method Room and Pillar Vein Dip/Thickness l0°/l5 ft Number of Levels/Max Depth 1/0 to 1800 ft 2 Haulage, Conveyances and Travelway Main Haulage Rubber Tire/10 miles belts Man-Ways - Typical Route of Travel to most Remote Sites Rubber Tired Vehicles Hoists - Capacity/Speed/Depth Depth under construction 3 Ventilation 2,500,000 cfm - 5 surface fans 4 Compressed Air N/A cfm 10" and 12" lines 5 Incendiary Storage 2 day powder 1000 gal fuel oil 6 Communications 1 complete system - all shops, dinner areas, and feeder/breaker stations 2 partial systems 7 Escapeway- Systems Man Check System Section boss log and punch cards Alarm System Mine phones with paging system Posting of Escape Route Maps No Escape Signs Every intersection, fluorescent paint Evacuation Drills 2/yr/shift Refuge Chambers - 1 cinder block - No longer required

Jan 1, 1976

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 9 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY; PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2;1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AROUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11;1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS 0F THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION.

Jan 1, 1977

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTILATION NETWORK ANALYSIS

Jan 1, 1977

By R. V. Ramani, V. T. Burgos, J. A. McClay

Introduction The Cost program was developed to provide the planning engineer with a tool to evaluate the cost implications of the technical mine design decisions. Direct costing methods are employed, where feasible, to provide greater detail and accuracy in the primary cost centers. Options have been provided in the cost computation, economic analysis, and output data subsystems to increase the flexibility of the system. Computer Program The program is written in Fortran IV for use in the IBM System 360/370 computers. i. Main - The main routine reads and stores input data from three sources, user input, Cost Data Library, and data transfer from the Master Design Simulator. Data is trans¬ferred to the appropriate subroutines, as they are called, by means of labeled common blocks. ii. Subroutine CSTCOM - is a data modification routine which computes the peripheral charges related to labor and supervisory costs. iii. Subroutine MANPWR - interrogates section data to determine the total labor and supervisory costs for each cost center. iv. Subroutine CAPCST - computes the total capital investment for each cost center, including the economic life and salvage value of each element. Capital costs are determined by user selection of quantities and models of equipment. Equipment costs are stored in the Cost Data Library for retriev-

Jan 1, 1975

By Craig Haase

A. Introduction

Jan 1, 2003

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 11 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY, PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2, 1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AFCUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11, 1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS OF THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION. IN THIS RUN, THE ORIGINAL VENTILATION NETWORK HAS BEEN MODIFIED TO INCLUDE NEW INTAKE AND RETURN AIRSHAFTS AT THE WEST MAINS.

Jan 1, 1977

By R. V. Ramani, C. B. Manula, A. Owili-Eger

• MINE VENTILATION NETWORK PROBLEM (NATURAL SPLITTING; FIXED • QUANTITY BRANCHES; METHANE SIMULATION; NETWORK TOPOLOGY REVISION; • ABSOLUTE PRESSURE) • NFIXB = NO. OF FIXED QUANTITY BRANCHES • DD(I) = AIR QUANTITY ASSIGNED TO FIXED QUANTITY BRANCH I, IN KCFP • NFBPF = NO. OF FIXED QUANTITY BRANCHES PLUS FAN • NFBPFG = NO. OF FIXED QUANTITY BRANCHES PLUS FAN PLUS METHANE • EMISSION BRANCHES • NBWNVP = NO. OF BRANCHES WITH NATURAL.VENTILATION PRESSURE • NVP(I) = NATURAL VENTILATION PRESSURE ASSOCIATED WITH • THE I-TH BRANCH • NF = NUMBER OF FANS • NB = NUMBER OF BRANCHES • MAXIT = MAXIMUM NUMBER OF ITERATIONS • MAXJ = MAXIMUM NUMBER OF JUNCTIONS • NJ = NUMBER OF JUNCTIONS INVOLVED IN THE SOLUTION * NM = NUMBER OF MESHES • NP = NO. OF POINTS TO DESIGNATE FAN CHARACTERISTIC * Q = QUANTITY OF AIR FLOW IN KCFM • R = RESISTANCE OF AN AIRWAY • WIDTH = AIRWAY DIMENSION • LENGTH = AIRWAY DIMENSION • HEIGHT = AIRWAY DIMENSION • SUMNVP = SUMMATION OF NATURAL VENTILATION PRESSURE FOR ANY MESH • X (I) = QUANTITY OF AIR, IN KCFM, ASSOCIATED WITH THE I-TB POINT • ON A FAN CHARACTERISTIC • E = ERROR FOR CONVERGENCE • FF = FRICTION FACTOR • FX(I) = FAN PRESSURE, INS INCHES OF WATER GAGE, CORRESPONDING • • TO A QUANTITY X(I) • H = HEAD LOSS IN INCHES OF WATER GAGE • I = BRANCH NUMBER • J, J1, J2 = JUNCTION, J1 AND J2 ARE TWO NODES WHICH DEFINE A • BRANCH • KEY = NO. WHICH SIGNALS THE TYPE OF FAN CHARACTERISTIC TO BE • EXPECTED

Jan 1, 1975

By R. V. Ramani, V. T. Burgos, J. A. McClay

The data for Test I describes an underground bituminous coal mine operation in a 48 inch seam, with an estimated production rate of 1,056,000 tons per year. The system includes four continuous mining sections, conveyor belt haulage, and a rail network for supply and personnel transportation. This section illustrates the input data sequence and the various report formats which may be selected for the printing of results. As explained earlier, at the present time, the elements of the Cost Data Library must be read in with the regular data input. Thus, in the input data listing, immediately following the required user input, are cards which contain the inputs of the cost library. Examination of the cost reports indicate the absence of cost values for some categories for which the system would normally be expected to incur costs. This situation has arisen due to the format of the cost data provided in the U. S. Bureau of Mines reports. An example of this is the charge of $20/ton for brattice cloth while no charge is indicated for stoppings. The test report data provided a single figure for ventilation cost without a supplemental breakdown. Thus the cost indicated for brattice cloth is actually the total ventilation cost. These explanations hold true for the data input and output for Test II, Appendix III.

Jan 1, 1975

By R. V. Ramani, C. B. Manula, A. Owili-Eger

PART 1 THE INPUT AND OUTPUT DATA AND THE MINE SCHEMATIC SHOWING THE FLOWS FROM COMPUTER SOLUTIONS FOR APPLICATION I

Jan 1, 1975

By Karl J. C. Harries

"The following is an outline or check sheet of some things that might be looked at when considering the concept of a royalty or royalty provisions. It is not intended as a guide to what is right or wrong (that is for the parties to decide). It does not replace the discussions in this work and is not intended to be a complete or exhaustive compilation of matters to be considered. It presumes that you are familiar with the basic concepts of royalties and has been included as an aide memoire only. Use it as such, with caution and common sense, and amend it to suit your needs. Remember also that brevity can result in inaccuracy or imprecision. This is a danger in many points below.The section references are for the sections where the matter is the main subject of the section – see the index for other sections.Royalty TypesNet Proceeds [§§ 5.8.; 11.4.]• No accepted or understood meaning within industry.• Literal meaning, if not defined, would imply “net operating profit”.• Often defined as net profit with revenue base of proceeds from sale of product.• Should not be used without detailed and clear definition. Net Operating Profit [§§ 5.8.; 11.4. – referred to only]• Net profit without recoupment of pre-production expenditures.• Revenue base: usually proceeds from sale of product.• Operating costs deductible.• Some reserves may be permitted.• Recoupment of some post-production capital expenditures may be permitted.• Not often seen as basis for royalties in Canada."

Jan 1, 2003

By R. V. Ramani, C. B. Manula, A. Owili-Eger

ANALYTICAL PRESSURE - VOLUME COMPUTATIONS FOR THE MINE PROTOTYPE A new coal mine is projected, with entrance by slope 1,500 feet long. Nine main entries will be standard for development, five as intake and four as return. One return shaft is planned near the slope bottom, and an intake shaft and portal are planned 5,000 feet north of the slope bottom. The slope will have an area of 150 square feet and a perimeter of 55 feet. A belt and supply track will be within the slope. The return shaft will be circular with a diameter of 18 feet and will be 500 feet deep with an escapeway. Two hundred feet of the shaft and 500 feet of the slope will be concrete lined. Select the fan to operate five units per shift and drive the 5,000 feet to a proposed new portal, using the slope for an intake. Two main splits are planned with the maximum of three units on any split. The amount of air desired at each unit is 25,000 c.f.m; a shop at the slope bottom will require 10,000 c.f.m. In the solution of this or any similar problem, the first step is to determine the resistance factors. CALCULATION OF R FACTORS Slope area = 150 sq. ft.; Perimeter = 55 feet; Length = 1,500 feet. The friction factor K must be established. Five hundred feet of the slope is smooth lined, moderately obstructed by belt; K = 35. The remaining 1000 feet is in sedimentary rock and moderately obstructed; K = 85.

Jan 1, 1975

By Karl J. C. Harries

"The Table of Contents that follows is only an example and is the Table of Contents from an actual negotiated agreement. It is merely intended to show how an agreement might be set out and the nature of possible provisions. As a negotiated agreement the format was dictated by the negotiations. It is not offered as a precedent of what should be contained in a joint venture agreement (“JVA”), the “proper” sequence of Articles, or a complete listing of the contents of joint venture agreements generally. The set-up used for an agreement should be decided by the parties and be one they consider flows in a logical and workable sequence. This example sets out the “deal” first, followed by the provisions relating to how work is to be carried out and then by administrative provisions necessary to make the agreement work. If you are more comfortable with, say, having the Committee provisions at the beginning, by all means have it drafted that way -- you are going to have to live with the agreement and work under it.Notes:1. The Table of Contents provisions appear in bold print. The italicized sections are annotations, which have been provided in some cases where the heading may not clearly describe the contents. They are not intended to be comprehensive, but refer to some specific matters that are considered to be of interest or to need some clarification.2. The subject matter of many of the articles and paragraphs is discussed or commented upon in the text of the book. Some of section cross-references have been provided. Such references are only to sections where the topic is a principal subject and no attempt has been made to provide a comprehensive indexing.3. Although this particular agreement is a three-party agreement, *B* and *C*, the Owners, are required to act as a unit (see para. 1.09. – § 8.44.), making the agreement effectively a two-party agreement. The parties insisted upon having a decision-making Committee and structuring the agreement accordingly. As is explained in § 8.11., such an arrangement is not recommended and can result in problems.5. See also §§ 8.24., 8.41. and 14.13. for discussions on tables of contents, summaries, and headings."

Jan 1, 2003