Search Documents

By S. N. Lekakh

Experimental work and thermodynamic simulations of cast iron refining were carried out using various additions of alkali and rare earth metals. The refining reactions for sulfur and oxygen removal were studied for melts treated with Mg, Ca, and Ce. The measured data and the results of the computer simulations were in agreement. Experimental kinetic data, together with the thermodynamic calculations, were used for optimization of the amount and sequence of the addition of nodulizers for ductile iron production.

Jan 1, 2009

By A. P. Paiva

Although the advantages of Solvent Extraction for separation/purification of relatively concentrated solutions are well known in Extractive Metallurgy, its use for the recovery of elements present in low levels only recently has been discussed, with particular attention devoted to precious metals. In this work, the extraction behaviour of Cyanex 471X towards silver, from an acidic chloride medium is reported, the extraction and stripping isotherms and related kinetic features analysed. Results on the selectivity of silver extraction against high contents of iron, copper and lead are discussed. Phosphine sulphide extractants are generally associated with solvation mechanisms: analysis of the extraction pathways along with the possibility of reaching a suitable loading in the organic phase are also presented.

Jan 1, 1993

By P. Mazumder

Numerical analysis is carried out to examine the effects of thermosolutal convection on the formation of complex patterns in directionally solidified binary alloys. A finite-difference analysis is used for dynamic modeling of a two-dimensional prototype of Vertical Bridgman system that takes into account heat transfer in the melt, crystal, and the ampoule; melt flow and solute transport. Actual temperature data from experimental measurements are used for accurately describing the thermal boundary conditions. A range of complex dynamical behavior is predicted in the melt flow due to flow transitions and this is found to be directly related to the spatial patterns observed experimentally in the solidified alloys. The model is applied to single phase solidification in the Al-Cu and Pb-Sn systems to characterize the effect of convection on the macroscopic shape of the interface. The application of the model to hyper-peritectic alloys in the Sn-Cd system shows that the presence of oscillating flow can give rise to a novel convection induced microstructure in which a tree-like primary phase in the center of the sample is embedded in the surrounding peritectic matrix.

Jan 1, 1999

By O. E. Omotoso

This study is part of an ongoing investigation to understand the mechanism of stabilization/solidification of hazardous chromium wastes in ordinary Portland cement (OPC). Tricalcium silicate (C3S*),a major component of OPC is mixed with reagent grade Cr(lll) and Cr(VI) solutions, to simulate complex cementiCr waste systems. Scanning electron microscopy (SEM) and energy disperse spectrometry (EDS) were employed to provide microstructural and chemical information. Transmission electron microscopy (TEMlEDS), apart from complimenting the SEM, was used to probe the distribution of Cr in the hydration products of C3S and to provide crystallographic information. 29Si MAS NMR (magic angle spinning - nuclear magnetic resonance) Was used to characterize the influence of Cr on the hydrated silicate structure.

Jan 1, 1995

By J. A. Eisele

There is currently much interest in how extraction of gold and silver from ores with acidic thiourea solution compares with extraction using alkaline cyanide solution. Agitation leaching tests were performed by the Bureau of Mines on 14 precious metal ores using sodium cyanide (?NaCN) and thiourea [(NH2)2CS) as extractants. The objective was to compare the results of the two extractants. NaCN was used at a concentration of 2 g/L with and without H202 as an oxidant. (NH2)2CS was used at concentrations of 2 and 20 gjL, and the solution potential was controlled at 390 to 420 mV standard hydrogen electrode (Eh) with Fe2(S04)3. With both reagents a.t 2 g/L extractant levels, NaCN extracted more gold and silver than (NH2liCS from all of the ores. At 20 g/L (NH2)2CS compared with 2 g/L NaCN, (NH2)2CS extracted more gold than NaCN from two ores, the same amount from one ore, and more silver from one ore. NaCN extracted more gold than (NH2 )2CS from 10 ores and more silver from 4 ores.

Jan 1, 1989

By Martín Reyes

Iron concentration by ion flotation techniques, from sulfate solutions in presence of zinc was studied in a laboratory flotation column by continuous mode using a synthesized sand shell plate sparger, an anionic collector, promoters, and surfactant propylenglicol 400. Effects of experimental parameters, such as the concentration of reagent: potassium amyl xanthate and dithiophosphate, superficial gas velocity, and superficial liquid velocity were studied in terms of the recovery and enrichment of Fe (III). The results show that the iron elimination from the solution in the presence and absence of zinc (II) are of 59 % and 72 % respectively. The flotation efficiencies decrease with an increase of the concentration of xanthate and air flow rate. The best recovery was achieved, at Jg 0.1 cm/s, Jl 0.72 cm/s and a mixture of xanthate and dithiophosphate as promoter. It was also demonstrated that it is possible to selectively separate and concentrate iron (III) from solutions containing zinc. The behavior of iron ion flotation in a flotation column is reported in this research as a gas hold up, superficial gas velocity, bubble size and superficial bubbles area flux function. The results show that the extraction of aqueous ions of metal iron by ion flotation is strongly affected by: [C], Jg (cm/s), eg (%), Db (mm), Jl (cm/s), y Sb (s-1).

Jan 1, 2009

By C. Lupi

Zinc impure solutions as spent electrolytes, leach liquors coming from aqueous treatment of both minerals and solid waste, need to be purified before undergoing the treatment to obtain the final product. Solvent extraction is one of the most selective operations particularly when many metallic ions are present in solution. Zinc pure solutions are frequently obtained using DZEHPA as extractant. In this work an investigation on zinc extraction effectiveness of naftenic acid was carried out. After determining the best diluent and the optimal extractant concentration, the partition coefficient was determined as a function of temperature, equilibrium pH and zinc concentration. Finally same batch tests to determine the equilibrium curves at room temperature on exhausted electrolyte coming from zinc cell were carried out by using naftenic acid, D2EHPA and TBP. The pH giving, for each extractant, the best extraction yield was selected in order to compare the equilibrium curves. Experimental results show that all the examined extractants are very effective in zinc extraction if the process conditions are appropriately selected. In order to avoid an impure solution pre- treatment and to obtain the maximum ertraction yield the appropriate solvent can be chosen.

Jan 1, 1998

By Takahiro Miki

Soldering material widely used is Sn-Pb alloy, which have low melting point and excellent electrical, strength properties and wettability. However, Pb is one of the toxic elements, which is undesirable due to environmental and safety reasons, thus Pb-free alternative alloy is preferred for new soldering materiaL Sn-Ag and Sn-Zn based alloys have been viewed as very promising candidates, among many potential substitutes. Addition of third element to these alloys will decrease melting point of the alloys. Hence, Sn-Ag-In and Sn-Zn-Mg alloys are expected to be suitable for replacing Sn-Pb solder alloy. In order to dcsign new Pb-free soldering materials, it is crucial to understand precise thermodynamic properties and phase diagrams of alloy systems. In the present work, ion current ratios of Ag to In and Mg to Zn were measured for Sn-Ag-In and Sn-Zn-Mg alloys by mass spectrometry, respectively. Also, the authors reviewed the thermodynamic properties of terminal binary alloys determined by other researchers and evaluated a thermodynamic functions to express the excess Gibbs free energy of each binary alloy. Thermodynamic functions to express the excess Gibbs free energy of liquid Sn-Ag-In and Sn-Zn-Mg ternary alloys were determined, utilizing the assessed Gibbs free energy of terminal binary alloys with the measured ion current ratios using mass speetrometer.

Jan 1, 2003

By Guo Xian Jian

In this paper, an alternative process to recover the value metals from polymetallic gold ore by FeCh leaching was proposed. In the process, gold was recovered by direct cyanidation from the leaching residue, the isolative electrolyte in chloride solution was selected to recover lead, the cementation with copper powder was used to recover silver and the solvent extracting was applied to recover copper and zinc. The total recovery of gold, lead, copper, silver and zinc in the process is 90.8%,96.05%,84.3%,81.98% and 54% to the bullion of gold, lead and silver and sulfate of copper and zinc, respectively. The process conditions selected for FeCh leaching are the temperature of 104°C, leaching time of 6 hours, Fe3+ content of 140 g/l and stoichiometry of FeCl3.

Jan 1, 1996

By X. J. Wu

Effects of various factors such as diaphragm materials, composition of electrolytes and current density on copper electrowinning from cupric chloride solutions was investigated. It is found that the crux of this process is to prevent the dissolution of copper by cupric ion and the formation of suspended CuCl precipitate. A process with high difference of copper concentrations between the feed solution and the spent electrolyte was selected. With this process, in which the feed solution contains 90 g/dm3 [Cu"], 3M NaC1, and 10mg/dm3 bone glue, and the spent electrolytes contains 10 g/dm3 [Cul, a very smooth and dense copper cathode can be produced with current efficiency above 93% and energy requirement less than 1.7 kwh/kg Cu at 25°C with N2 sparging. If a slightly higher energy requirement is permitted, smooth and dense copper cathodes can be produced at the current density up to 800 A/m2 with the identical solutions.

Jan 1, 1991

By E. B. Freidina

We have investigated a new electrochemical process for preparing lead-calcium alloys. Calcium metal, reduced fiom a molten chloride mixture, forms an alloy with liquid lead cathode. The addition of calcium carbonate to conventional CaC12-NaCl electrolyte enables us to avoid chlorine production on the anode and replace it with oxygen and carbon dioxide. The ternary system CaClz-NaC1-CaCO3 has a range of melt compositions, where the electrolysis can be held below 650°C. In order to prevent the side reaction of carbon deposition on the cathode we have separated the anolyte from the catholyte with alumina diaphragm. The factors, which affect the level of impurities and the current efficiency of the process, are discussed.

Jan 1, 1999

By P. Wieser, D. Feke

"Priming of filters with small pores is influenced by the surface tension of the liquid metal and may be complicated by freezing • Freezing followed by melting has been observed experimentally. This process has been modeled on the basis of one dimensional heat flow by radiation to the filter and by conduction in the metal. Also considered are super-heat of the metal and the initial filter temperature. The results of the model provide useful guidelines for the application of filters. IntroductionFiltration has been recognized as a valuable method of refining by removing suspended phases from liquid metals or alloys. Woven fiberglass type fabrics and wire screens were used initially in the aluminum industry. With the introduction of the ceramic filters that exhibit improved inertness and refractoryness, filtration has been introduced to higher melting alloys including cast irons, superalloys, stainless steels, as well as low and medium carbon low alloy steels. A considerable literature is delveloping rapidly on the progress in applications and the advances in understanding the mechanisms and effectiveness of filtration processes (1-8).With the use of filtration for different alloy systems for the production of cast to shape parts a bewildering variety of gating system modifications has been developed (Figure 1) to accommodate the installation of filters in the mold. The modifications have two principal purposes: 1) the runner expansion is intended to compensate for the resistance to flow due to the filter and that of the captured inclusions, and 2) the metal reservoir upstream of the filter, provides a temporary by-pass which permits metal to flow across the filter and heat it until priming can be accomplished. priming of.filters by low and medium carbon steel is readily accomplished but, compared to such alloys as cast iron or 19 Cr-9Ni stainless steel, requires greater precautions to avoid failure to prime by excessive freezing on or inside the filter pores. This problem is further examined below:"

Jan 1, 1986

By Ximena Diaz

Mercury is one of the most undesirable contaminants in gold bearing ores. During cyanidation mercury cyanide compounds accompany gold in all the extraction and recovery processes. Of course mercury in the carbon eluates creates environmental problems in subsequent refining steps. One possible process alternative for the separation of gold from mercury in such concentrated alkaline cyanide solutions is the selective solvent extraction of gold by undiluted Dibutyl Butyl Phosphonate (DBBP). In order to describe the behavior of mercury during extraction by DBBP, the results from a preliminary research program are presented. In this study, temperature and cyanide concentration have been found to be the most significant variables which influence the separation of gold from mercury by solvent extraction using DBBP. It was found, using plant eluate from a carbon strip, that excellent separation of gold from mercury can be obtained at 60' C with 98% gold recovery and complete mercury rejection in a single stage of extraction. The influence of pH is also discussed in terms of the extraction chemistry. These results complement previous research which described the DBBP solvation extraction of an aurocyanide ion pair. In addition, these results extend our understanding of the alkyl phosphorous ester extraction systems by illustrating that neutral ionic species such as Hg(cN)02sq, can be extracted at low cyanide concentrations, a phenomenon which had not been observed previously for other cyanoanions.

Jan 1, 1993

By W. G. Davenport

Inco flash smelting blows industrial oxygen, dried Cu"Fe-S concentrate, Si02 flux and recycle materials horizontally into a hot (-1500 K) furnace. Once in the furnace, the oxygen reacts with the concentrate by Reactions 1.1, 1.2 and 1.3 to give: (a) liquid matte, 55 to 60 mass%Cu (b) liquid slag, 1 to 2 mass% Cu (c) off gas, 60 to 75 volume % S02. The matte is tapped into ladles and sent to converting, Fig. 1.3. The slag is tapped into ladles, and sent to a stockpile; with or without a Cu-from-slagremoval step. The off gas is water-quenched, cleaned of dust and sent to a sulfudc acid plant. The [nco flash furnace is also used to recover Cu from molten recycle converter slag. The slag is poured' into the furnace via a steel chute and water-cooled door, Fig. 3.1. In 2000 there are five Inco flash furnaces in operation: at Almalyk, Uzbekistan (Ushakov, et at. 1975); Hayden, Arizona (Marczeski and Aldrich 1986); Hudey. New Mexico (Belew and Partelpoeg, 1993); and Sudbury, Ontario (two furnaces, Carr etal, 1997, Humphris et ai, 1997; Molino et ai, 1997). The Almalyk, Hayden and Hurley furnaces smelt Cu-Fe-S concentrates. The Sudbury furnaces smelt Ni-Cu-Co~Fe-S concentrates'to produce -45% Ni+Cu+Co matte and -1% Ni+Cu+Co slag.

Jan 1, 2001

By Gus Van Weert

This paper describes the results of autoclave testwork where ferric nitrate was hydrolysed in the presence of certain cations and anions and the resulting hematite analyzed for foreign constituents. For the cations Zn++, Ni++, Cu++, and AI+++, selectivity factors of over 107 were found. Magnesium gave 3.106. These factors are calculated as Me/Fe in solution over Me/Fe in the hematite; Me representing the metal in ion added. As-a result of the testwork at Delft University of Technology, BUDELCO (the Netherlands electrolytic zinc producer) ran a series of ferric nitrate hydrolysis tests in the presence of 10 additional trace elements. Impurity levels were prejudiced on Me2 EPHA extraction of iron from their zinc circuit, followed by HNO3 stripping. Good selectivity against base metals was confirmed, but trace elements forming anions (As. Sb) and sulphate were incorporated in the hematite. These BUDELCO results are also presented.

Jan 1, 1995

By P. Cowx

The carbothermic reduction of zinc oxide rich Electric Arc Furnace baghouse dust in the Tetronics transferred arc plasma furnace to produce a non-toxic slag and a metallic zinc product is described. In particular, the operation of the zinc splash condenser coupled to the plasma furnace is examined and the effect of process variables on zinc recovery is discussed.

Jan 1, 1990

By Kazuhiro Asai

Nippon Mining and Metals Company has an annual indium production capacity of 30 tons at its Saganoseki smelter and refinery. Lately, indium content in the. zinc smelting dust, one of the main sources, has been on the decrease while the amount of impurity in it on the increase. The present process at Saganoseki does not permit efficient elimination of a large. amount of impurity. Therefore, studies were conducted to improve its recovery process. As a result, a new indium recovery process consisting of leaching, solvent extraction and electrowinning has been developed. The new process was tested at a pilot plant and satisfactory results were obtained. This new process is discussed in this paper.

Jan 1, 1995

By Yin Zhang, Xiaoyu Huang, Mi Wang, Bencheng Du, Youduo He

"Burners are important facilities for blast furnace stoves to raise hot-blast temperature up to 1200°C. Common types of two-ring ceramic burners have very long flames so that part of combustion occurs in the upper part of the chequers and will cause damage to the refractory materials. Using computer simulation to analyze the turbulent diffusion flame in the combustion chamber, some good results were obtained. A new type of ceramic burner will be installed by Anshan Steel Complex in stoves of blast furnace number 4. A pilot experiment was done on the new burner. The experimental data have shown that the mixing condition was improved and the length of flame was shorter with the new type of ceramic burner.IntroductionPulverized-coal injection can give significant operating saving, reducing coke rate in blast furnace(BF) operation. However, during high rates of coal injection, extra heat must be compensated in hearth to maintain certain raceway adiabatic flame temperature. One of the effective methods for heat compensation is to raise hot-blast (HB) temperature up to 1200°C. Nowadays, since the fuel being combusted in stoves is BF gas only, in which the calorific value is down to round 3000 kJ/m3 , to increase the combustion ability and to provide a suitable length of flame in combustion chambers of stoves becomes more important. In other words, designing a good ceramic burner which will affect to HB temperature and stove lifetime is drawing more attention."

Jan 1, 1999

By Jhon Cuya

Titanium dioxide is the well-known catalyst for the photodecomposition of water in UV region and its nanoparticles show better performance than its bulk materials. Furthermore, partially sulfurized TiO2 is expected to be chemically stable and have an enhanced photocatalytic activity compared with TiO2. For this purpose, the sulfurization behavior ofTiO2 nanopartic1es was thermogravimetrically (TG) studied by a thermo-balance with a quartz spring using CS2. From the TG curve of TiO2 nanopartic1es, first, the weight decrease appeared down to around 8 wt% and then sulfurization reaction started at around 500°C at a heating rate of 1 C°/min. The weight increase curve showed a maximum of ca 30 wt% at around 750°?C and then gradually decreased to ca 12 wt% at 1000°C. This would be caused by the formation of TiS2 followed by the decomposition ofTiS2 to lower sulfides, such as Tit.0.8S2 and Ti3S4. From the comparison of the sulfurization of TiO2 nanoparticles with that of anatase, rutile and Ti(OH)4, it was found that TiO2 nanoparticles showed a similar behavior to that of Ti(OH)4.

Jan 1, 2003

By Gabriel Plascencia

Copper was oxidized in the temperature range from 300 to 1000 GC under different pressures of oxygen. In the range from 300 to 500°C, copper oxidizes following the logarithmic rate law; while in the range from 600 to 1000°C oxidation follows the parabolic rate law. Transition from logarithmic to parabolic growth occurs at about 525°C. X-ray diffraction was performed on oxide scales to account for the CuO/Cu2O ratio at different temperatures. Activation energies found in this work are in good agreement with reported values.

Jan 1, 2003