Search Documents

By Corby G. Anderson

In nature, mercury is quite commonly found in association with antimony ores. This can be as a separate mineral such as cinnabar or in direct association with the antimony ore. The most common antimony-mercury mineral is livingstonite that occurs in places such as Algeria, Mexico, USSR and China. In the Roznava deposit in eastern Slovakia, tetrahedrite ore containing mercury ore has historically been processed pyrometallurgically for its silver and copper values. As well, in Tajikistan, major antimony deposits there contain significant mercury ore concentrations within the stibnite ore body. The mercury contained in these materials poses both a processing and environmental challenge. This paper will outline the processing of these types materials by industrial alkaline sulfide hydrometallurgical methods. The economics relevant to this potential application at Roznava in Slovakia will be outlined.

Jan 1, 2003

By Shuai Wang, Gang-hua Fu, Lu Yang, Yu-feng Guo, Tao Jiang

The fluorine-bearing iron concentrate is one of the refractory raw materials for pelletization, which is mainly used in Baotou iron and steel company with lots of problems, such as narrow roasting temperature range and low compressive strength of products. According to its specific character, the effects of roasting temperature, time on the compressive strength and microstructure of pellets were researched. The results show that low melting substances formed during the roasting was the dominant reason of those problems. High melting substances were added in the roasting to investigate their effects on the roasting properties of fluorine-bearing iron concentrate pellets. Low melting substances were reduced when chromite was added. The compressive strength of products was 3100N/P when the 2% chromite was added at the roasting temperature of 1150 ºC, which was increased 700 N/P compared with the pellets without chromite, and the roasting temperature range was expanded by 170 ºC.

Jan 1, 2016

By Nobuo Takahashi

Effective solvent extraction media have been investigated for purification of rare earths. At first, a quaternary ammonium compound was studied. The counter anions of rare earths and organic dielectric substances were tested to improve separation factors,. And second, crown ethers were selected for extractant. Several diluents of crown-adducts were tested to improve solubility and distribution coefficient as well as the counter anions of rare earths. Especially, in the presence of strong reducing agents, highly selective extraction of europium from other rare earths was observed. The third extactnts were ß -diketones. Presence of organic dielectric substances was very effective to improve separation factors. Though those. three groups of extractants were suitable for mutual separation of light rare earths, alkyl esters of alkyl-phosphonic acids were suitable for mutual separation of heavy rare earths because of their high separation factors. To keep proper pH value was necessary for acidic extractants, so control method of the solution pH was studied with high molecule insoluble amines or salts of those.

Jan 1, 1995

By Katsutoshi Inoue

Pectic acid gel crosslinked with epichlorohydrin was found to have very high selectivity to lead(II) and iron(III) ions over zinc(II) ion compared with commercial weakly cation exchange resins containing the same carboxylic functional groups, suitable for removing small amount of impurity metal ions from waste zinc plating solutions. In order to lower the cost, new adsorption gel was prepared from orange juice residue containing pectic acid by crosslinking with epichlorohydrin, which was also found to be suitable for removing these impurities. Further, very cheap adsorption gels was prepared not only from orange but also from apple juice residues by a simple method through just saponificating pectin substances contained in these residues into pectic acid by calcium hydroxide followed by water washing and drying. These adsorption gels exhibited excellent adsorption behaviors for removing the impurity metal ions away from zinc.

Jan 1, 2003

By J. K. S. Tee

Using a novel method, zinc has been selectively removed from galvanized steel scrap on a laboratory scale. The separation is based on thermodynamic principles: during chlorination in air-chlorine (10:l) mixtures at 800 OC, zinc forms a volatile product (zinc chloride) while iron does not chlorinate as its oxides are more stable than the respective chlorides. As much as 92 % of zinc is removed from the surface of steel within 10 minutes. This process overcomes tedious and costly preparatory stages associated with leaching - electrowinning methods.

Jan 1, 1999

By Marco Olper

After two years of extensive research a new and innovative modification to the CX-EW process has been exploited. This process, called CX-EWS, avoids completely all the critical aspects of the previous process which affected the cost of the energy, of the chemicals and of The maintenance of the insoluble anodes. All these benefits reflect a saving of about 30% of The operating costs compared to the present traditional production and allow for a total operating costs of less than 6.5 cts/lb. lead (net of raw material cost). With this new technology it is allowed for the first time the treatment in the same plant facilities of both primary lead sulphide concentrate and spent batteries. The paper describes the technical and economical aspect of the new process with a feasibility study for 150,000 t/y spent battery facility throughput.

Jan 1, 1995

By Baozhong Zhao

Experimental results have shown that fluxing with soda ash (Na:zC03) can remove As and Sb from molten copper at the rate of As>Sb, but is relatively ineffective in removing Hi. The rate of impurity removal is controlled by impurity mass transfer in the metal phase. In this paper, a mathematical model was developed to describe the impurity removal phenomena. The model incorporates the effects of molten bath mixing intensity, soda ash feeding rate, oxygen content in the molten copper and soda ash fluxing by surface addition and injection. The model predictions are in good agreement with experimental results and may be used in designing large scale tests.

Jan 1, 1996

By Steve Lloyd, Ryan J. Foy, Brandon Steinborn, Jerome P. Downey

Research was performed to evaluate copper and silver extraction from samples of bornite flotation concentrate. Sulfation roasting experiments were performed in a rotary tube furnace, a fluidized bed reactor, and a static bed muffle furnace. Roasting was plagued with rapid, lowtemperature calcine sintering, apparently related to the presence of organic matter in the concentrate. Calcine entered a weak acid leaching process to remove copper, and silver was extracted from the weak acid leach residue in a ferric chloride and hydrochloric acid solution. Copper extraction efficiencies in excess of 90% were attained in the weak acid leach while 90% silver extraction was achieved in the ferric chloride leach, along with copper and lead extractions as high as 93% and 99% respectively. The two-stage leaching process resulted in overall extraction efficiencies of 99% copper and 90% silver.

Jan 1, 2015

By S. Mondon

Hibi Smelter which is a Copper Smelter lining a blast furnace, produces 2,700 metric tons of anode copper per month. Generally, in a copper refinery, arsenic and antimony are considerably troublesome impurities. With regard to the elimination of antimony, Hibi Smelter has two handicaps described as follows. (1) Smelting under the slightly oxidizing atmosphere in the blast furnace. (2) Recycling the converter slag to the blast furnace after cooling. Therefore antimony and arsenic, mainly antimony, elimination tests, in which the alkaline flux was injected through the two tuyeres in the blowing stage, were carried out in the rotary anode furnace. Antimony and arsenic were respectively removed more than 90 96 from the molten copper, and their high eliminations are discussed by application of the transitory and permanent reaction model with the flux injection, which was presented by T. Lehner.

Jan 1, 1983

By Lin Li, Xiang Li, Yifang Zheng, Jilai Xue, Jun Zhu

"Al drops and gas bubbles in the anode-cathode space of aluminum electrolysis cell are of great importance for cell operation improvement in metal loss, current efficiency and energy consumption. A direct observation on the Al drop, gas bubble and ultrasound was carried out through a see-through cell. The Al drop immersed into the cryolitic melt was found moving up and down irregularly in the anode-cathode space without electrolysis, which was then completely dissolved into the melt. During electrolysis, the Al drop came to the anode area and reacted with the gas bubbles generated on the anode. Under ultrasound, the gas bubbles were removed from the anode surface while the Al drop was kept on the side of anode. The observed phenomena were useful for technology improvement in reducing the anode-cathode distance or lowering the energy consumption in aluminum electrolysis.IntroductionDuring aluminum electrolysis, aluminum metal drop and anodic gas bubble are in close contact each other within the anode-cathode space, and the interaction between them can produce significant impact on metal loss, current efficiency and energy consumption. The motions of the Al drop and the gas bubble are also related to the dissolution of aluminum metal into cryolitic melt and the cell voltage drop due to the bubble layer covering the anode surface.A number of studies have been carried out using different types of see-through cells, where the dissolving process of metal Al into cryolitic melts (metal fog) in the anode-cathode space was directly observed and photographed [1, 2]. With the similar method, some direct observations on the anodic bubble behaviors with and without ultrasound were performed during aluminum electrolysis [3-6]. However, to our best knowledge, there is no published work on direct observation on the behavior of Al drops and anodic gas bubbles staying together within the same anode-cathode space, as well as the motion and interaction of them in cryolite-alumina melts."

Jan 1, 2011

By C. Lupi

"The energy consumption of copper production by electrowinning, generally represents more than 1/4 of the total energy requirement in hydrometallurgical traditional process (roasting, leaching, purification and electrowinning). The considerable saving can be achieved just in this step that requires about 2.2 kWhlkg of the produced copper. To save energy the cell voltage, or more appropriately its anodic component, can be reduced: that is because the anodic voltage represents the main component of cell voltage and so it is largely responsible for the excessive energy consumption in copper sulphate electrowinning.In this work some ways are studied to lower the anodic voltage. First the cobalt ions were added to the sulphate solution in order to study the catalytic effect on oxygen discharge. Then lead alloys anodes (Pb-Ag, Pb-Sb-Ag and Pb-Ca) were used to promote a better oxygen evolution as a result of a different anodic surface. Their behaviour was compared with the PbSb traditional ones. Finally, as already pointed out by several authors for zinc electrowinning, ethylene glycol was employed as anodic depolariser in order to verify its effectiveness in the case of copper electrowinning. By combining all the above-mentioned ways, energy saving ranging from 20% to 27% is achieved.All the tests were carried out on a laboratory pilot-plant for long time to simulate the industrial conditions. The obtained copper deposits were observed by SEM to highlight their morphology."

Jan 1, 1997

By Nobuo Kikumoto

Recently, the treatment of industrial waste materials has been a serious social problem here in Japan. Filling them in ponds is now strictly prohibited due to a limited land area and incineration method is also regulated as not to generate DXN. In these conditions, Onahama Smelter has begun to treat shredder dusts (SD) of car at reverberatory furnaces to recover various metals such as copper, gold, silver and palladium without generation of DXN. The total volume of these dusts is expected more than 1 million metric tonnes a year in Japan. Onahama Smelter is now planning to treat about 20% of them in the near future by using tonnage oxygen. In this paper, the heat balance, control method of DXN and treatment of these dusts in reverberatory furnaces are described. DXN : Dioxin (The generic term of PCDD and PCDF)

Jan 1, 2000

By D. Neuschiltz, M. Witthaut, R. Cremer

"Metastable (Ti,Al)N coatings with fee structure have been shown to exhibit superior performance as compared to TiN under conditions of wear at elevated temperatures due to their better oxidation resistance and hardness. The oxidation resistance of these coatings increases significantly with increasing Al-content. However, the deposition of (Ti,Al)N films with Ti/ Al ratios below about 30/70 leads to a hexagonal structure which is not suitable for tribological coatings. Only little is known about the location of the cubic to hexagonal phase transition and hence about the optimum composition of (Ti,Al)N hard coatings.To determine the position of this transition, Tii-xAlxN films with different Ti/Al ratios were deposited on high speed steel at substrate temperatures between 100 and 700 °C by means of reactive MSIP. The composition of the films was determined by electron probe microanalysis (EPMA) and X-ray photoelectron spectroscopy (XPS), the crystallographic structure by thin film X-ray diffraction (XRD).It could be shown that in case of deposition temperatures of 300-700 °C a two-phase region exists in the metastable TiN-AlN phase diagram, which expands with increasing temperature, wheras at 100 °C substrate temperature no two-phase region was observed. But in opposition to the phase diagram known from literature, which is based on thermodynamic estimations, the detected two-phase region is narrow for typical PVD temperatures, thus allowing the deposition of cubic single-phase Al-rich (Ti,Al)N hardcoatings for tribological applications. Based on these results, a new Ti1-xAlxN film with x = 0.62 has been developed, which showed an increase of oxidation resistance by a factor of 4."

Jan 1, 1998

By K. A. Brunk

Newmont's research, operations, history and experience with pre-treatment of preg-robbing carbonaceous ores are described, with emphasis on the chemistry, physics and kinetics of chlorine treatment. Present operations, control strategy and projected changes are also described, including a summary of the adsorption of chlorine into pulps and off-gas scrubbing. Conditions of chlorination have been optimized by the use of Eh-pH diagrams of the gold-chlorine-water system, and have resulted in significant increases in gold recoveries and decreases in chlorine consumptions.

Jan 1, 1987

By K. Itagaki, H. Henao

"The experimental study on the phase equilibrium and distribution of minor elements such as chromium and copper between magnesia saturated FeOx-MgO-SiO2 slag and Fe-Ni alloy were carried out under controlled oxygen partial pressure between 10-6-5 and 10-10 using CO and CO2 mixed gas at 1773 and 1873 K.The effect of slag additives such as lime (CaO/SiO2 molar ratio: 1) and alumina (AlO1.5/SiO2 molar ratio: 0.1) on the distribution behavior of the minor elements was also investigated.The value of distribution ratio for chromium, defined by (%Cr in slag)/[%Cr in alloy], is larger than 70 at the pO2 region conducted in the present study for the MgO saturated FeOx-MgO-SiO2 slag at 1773K. These value are almost 4-order higher then that of nickel though the distribution ratio of copper shows similar values with nickel. Analysis of the data indicates that addition of lime in the slag and the increase of temperature reduce the dissolution of chromium into the slag and the addition of aluminum increases the dissolution of chromium into the slag while reduces the dissolution of copper and nickel.IntroductionChromium. is a minor element in a nickel oxide ore but a Japan major component in the secondary material of stainless steel and is also introduced in the Fe-Ni production process due to dissolving bricks of a furnace. Chromium is a concerned matter for the beneficial utilization and disposition of ·slag because Cr6+ is a harmful element. Considering Fe-Ni as an alloy component in steel making, and the demand of high purity nickel, chromium is an -undesirable element that has to be eliminated into slag prior to the steel making, or the production of high temperature refractory alloys. On · the other ·hand chromium is an element of steel alloy for many applications, thus Fe-Ni containing chromium in minor element is desirable in some stainless steel making."

Jan 1, 2000

By Qionghua Zhou, Wei Liu

"Nanocrystalline silver bulk material with average grain size of 20.3 nm was prepared by warmvacuum- compaction method. The as-prepared nanocrystalline silver was characterized by X-ray diffraction (XRD), differential scanning calarmeutry analysis (DSC), thermogravimetric analysis (TG), and 6157 type Electrometer test, respectivily. The experimental results show that the average grain size and microstrain of the nanocrystalline silver are 20.3 nm and 0.088%. The melting point and melting enthalpy are 1228.7 Kand 82.34 Jig, which are lower than that of coarse-grained silver by 6 Kand 22.6 Jig, respectively. The electrical resistivity of nanocrystlline silver increases with higher temperature when the range of temperature is between 233K and 293K. The electrical resistivity at 293 K is 1.475xlO -7 Q·m, which is higher than that of coarsegrained silver by a factor of 9.IntroductionN anocrystaline ( nc) materials or nano structured ( ns) materials are three-dimensional (3 D) bulk materials with average grain size typically smaller than 100 nm. Ne materials have been of great interest for their unique properties, such as superior tensile strength [1-2], high microhardness [3- 4], superplasticity [5-6], magnetically quasi-isotropic [7-8] , and so on, making them one of the most promising nano-scale materials with wide applications. Ne materials with average grain size of 5-10 nm were firstly fabricated by Gleiter et al. [9] in 1980s, using inert gas condensation (IGC) method. Unfortunately, the large surface to volume ratio creates a high surface energy component in the total free energy of the system and results in a metastable state in the materials. Therefore, due to the signfica nt disordered grain boundary regions, nanomaterials are thermally unstable and are subjected to a strong driving force for grain growth. The grain growth even occurred at room temperature [10].The conflict or deviation of measured date, e.g. strength, microhardness, thermal stability, partly due to the grain boundary ratio or the distribution of grain size, and partly derived from imperfections such as voids and microcracks while earlier processing techniques are known to result in incomplete dens:fication [11-12]. Therefore, the higher quality samples produced in subsequently years still show such a general trend."

Jan 1, 2011

By C. O. Bounds

Management of emission control dust from electric? arc furnace (EAF) steelmaking as an RCRA-EPA listed hazardous waste places economic and environmental pressures on the steelmaking industry. Horsehead Resource Development Company, Inc. (HRD) serves the industry by recovering nonferrous metals from the dust in rotary kiln plants in Palmerton, PA and Chicago, IL, and has demonstrated the commercial viability of its patented coal-fired FLAME REACTOR Process. However, because of location and/or regulation, many steelmakers could be more economically served via on-site processing of its dust. Therefore, in 198-7, through a contract with the Gas Research Institute, HRD embarked on a program to develop a gas-fired reactor and test a prototype unit. The development program has successfully proven the environmental, technical and economic performance of the concept. Consistently high zinc, lead and cadmium recovery to an oxide concentrate as well as production of a nonhazardous, delistable slag have routinely been achieved. The gas-fired FLAME REACTOR field experiment results and the economic performance of on-site or smaller regional plants will be highlighted.

Jan 1, 1990

By Ann M. Hagni

The mineralogical, chemical, microtextural, and particle size character of electric arc furnace (EAF) dusts are being studied by reflected light microscopy, scanning electron microscope-energy dispersive spectroscopic analysis (SEM-EDS) and electron probe microanalysis (EPMA). The dusts consist predominantly of metallic iron, iron oxide, and calcium-iron-manganese silicate phases, together with smaller amounts of iron-manganese-zinc-calcium, iron-calcium-zinc-manganese, and calcium-iron-manganese silicates. The samples vary in their zinc contents. Chlorine occurs in phases containing iron, lead, zinc, manganese, and calcium. The dust particles range greatly in size from 1 to more than 300 ~m, but most particles are about 1 to 6 ~m. Larger particles. about 20-50 um across. also are present. They are predominantly spherical in shape, but some are cenospheres, and others are more angular particles, some of which are broken spheres and cenospheres. Their internal microtextures exhibit evidence of liquid immiscibility, exsolution, skeletal crystal growth, and oxidation react i on rims. Because EAF dusts have been classified by EPA as hazardous wastes, there is heightened interest in the treatment of these dusts to render them non-hazardous. The mineralogy of products of pyrometallurgical treatment of EAF dusts by flash furnace and pyrohydrolysis are currently under study.

Jan 1, 1991

By P. J. Uggowitzer, H. Kaufmann

"New Rheocasting is a novel route of semi-solid casting, in which the globular semi-solid precursor material is produced by controlled cooling of only slightly superheated melts in conventional steel crucibles. The resulting semi-solid slugs are placed into the sleeve of a vertical Squeeze Casting Machine and then filled into steel dies. Solidification occurs under hydraulic pressures up to 100 MPa Due to the reduced cost of precursor material, reduced investment cost and easier recycling, the New Rheocasting process offers cost reductions of up to 25% over conventional semi-solid casting · routes. The New Rheocast products are pore free, pressure tight, weldable and heat treatable castings.In the present work the New Rheocasting Process is introduced and the influence of heat treatment on mechanical properties of the New Rheocast alloy A356 is discussed.The alloy A356 is cast under ideal New Rheocasting conditions into a step die on an UBE HVSC 350 Squeeze Casting machine. As-east, TS and T6 heat treatment conditions with variations in solutionizing and aging time/temperature parameters are applied and the samples are tested by tensile testing. Alternatively, the same heat treatment conditions are applied to conventional Squeeze Casting parts and compared with New Rheocasting.Questions of potential cost savings due to modified heat treatment conditions are also addressed in this paper."

Jan 1, 2000

By Ruth Marlene Campomanes Santana, Michel Tieccher, Marcondes Mafacioli Pacheco, Juliano Urach

"IntroductionThe gaseous emissions of fuel burning by mobile sources are responsible for incidence and increase of many lung and cardiovascular diseases (Braga et al., 2007). These implications can watch in morbity as much as mortality, even when the levels of pollution are considerate restrained or lower. (Leite et al., 2002).Sample of mobile sources exhausts contain not only particles directly shaped by burning, but also secondary particles that results of reaction between other compounds (Burtscher, 2004).One of the principal pollutants produced by combustion process with major toxicity and raiser of adverse effects to health is the particulate material. In its constitution there are fine and ultrafine particles that can to extend deep portion of breath system, break epithelial barrier and reach the interstitial of lungs and then, to unleash inflammatory process (Arbex, 2004).The Particulate Material is employed to define a mixture of solid particles and liquid drops suspense in atmosphere. Queiroz et al. (2007) declare that this material can be divided in two types separated by size interval that together, represent the major class of disperse particles: the fine particles type of 2,5 µm de (breath particulate) and the type of earthliness particles, major than 2,5 µm to 10 µm (inhale particle). The difference of size between the particles influences on the physics and chemistry properties. They affirm that exist correlation between size of particle and heavy metals; how many lower was the dimension of particulate materials, major is the concentration of heavy metals.The inhale particulate (MP10) that is object of present study can exhibit in your composition sulfates, nitrates, amoniacal, marine salt (NaCl), soil elements (Al, Ca, Fe, Si, Ti), metals (Cd, Cr, Cu, Ni, Pb, V, Zn) and water (Queiroz et al., 2007).Recent studies have exhibit strong relation between daily levels of particulate material inhale (MP10) with diameter until 10 µm and others pollutants and one infinity of effects to health that go since total mortality of population, sicken for specific causes until congenital bad formation or even difficult win weight by the fern during gestation (Gouveia et al., 2006)."

Jan 1, 2008