Search Documents

By S. V. Subramanian

The tool material and the machine design for high speed machining are well advanced over the last decade but the steel design has lagged behind. The paper examines the design of steel in order to control the sliding tribology for high speed machining under dry machining conditions. In high speed machining of steel, accelerated chemical wear of the tool occurs once atomic contact is established at the tool-chip interface, resulting in poor tool life even with high performance tools such as cubic boron nitride. Recent research has confirmed the occurrence of nanocrystalline grains in the interfacial layer of the chip at the tool-chip contact. The volume percentage of grain boundary is increased significantly (10 to 30%) as the nanocrystalline grain size is decreased well below 30 nm. The solubility of tool material into the nanocrystalline grain boundary is two or three orders of magnitude greater than in the crystal lattice. Further the kinetics of diffusion in the grain boundary is seven or eight orders of magnitude greater than in the crystal lattice. Enhanced nanocrystalline grain boundary diffusion occurring in the interfacial layer at the tool-chip contact causes the accelerated chemical wear. Significant improvement in tool life could be achieved by engineering glassy oxide inclusions in steel, designed to self-lubricate the tool-chip interface in-situ at higher cutting speeds. Thus the control of sliding tribological condition at the tool-chip interface is key to suppress nanocrystalline layer formation at the tool-chip contact and hence prevent accelerated chemical tool wear. Sulfide inclusions are designed essentially to promote chip fracture. In addition, sulfide inclusions are designed to act as a diffusion barrier at the tool-chip interface. The application of inclusion engineering concepts to enhance the tool life in high speed machining will be demonstrated with a suitable case history.

Jan 1, 2006

By Naiyang Ma

"High oil concentration is one of the major barriers for recycling of mill scale of steel hot rolling mills. It is of vital importance to find cost-effective technologies of reducing oil concentration in mill scale in order to recycle the mill scale without causing detrimental effects on production and environment. This paper discusses in-process separation of mill scale from oil at steel hot rolling mills. Formation of mill scale and status of oily wastewater at hot rolling mills are reviewed in the first place. A mathematical model is then formulated to relate oil concentration in mill scale to physical properties of mill scale, chemical and physical properties of wastewater and interacting parameters between mill scale particles and wastewater. From this model, three approaches of in-process separation of mill scale from oil are derived: (1) avoiding contacts between mill scale particles and oily wastewater, and (2) maintaining low oil concentration in wastewater, and (3) collecting mill scale in upper streams of wastewater flows. In-process separation of mill scale from oil might have advantages of lower capital cost, lower operating cost and less additional environmental concerns, compared to other strategies of separating mill scale from oil.IntroductionHot rolling is an inevitable step in producing finished steel products. Figure 1 schematically shows a steel hot rolling process. Semi-finished steel products, slabs here, are reheated first, and then the reheated slabs are discharged from the furnaces and transported on hot rolling trains to descaling units for removing scale with pressurized water. After being descaled, the slabs are rolled by roughing mills. After treated with cropping and the second descaling, the slabs are finally rolled into finished products, coils here, by finishing mills."

Jan 1, 2012

By Min Chen, Nan Wang, Zhen Tian, Yingying Shen

"The enrichment behavior of phosphorus in CaO-SiO2-FeOx-P2O5 slag was studied by making an investigation on the distribution of phosphorous content in slag and 2CaO·SiO2 phase. The research results showed that the existing 2CaO·SiO2 solid particles in slag were the sites for the phosphorous enrichment. The enrichment process of phosphorus in CaO-SiO2-FeOx-P2O5 slag can be recognized as: mass transfer of phosphorus from bulk slag toward the surface of 2CaO·SiO2 particle, superficial dissolution reaction of phosphorus to 2CaO·SiO2 and diffusion of phosphorus through the product layer of 2CaO·SiO2-3CaO·P2O5 solid solution to the inner of 2CaO·SiO2 particle. Compared to the 2CaO·SiO2 particles with larger size (500µm to 1000µm), the completion time of enrichment was shorter for the particles with smaller size (less than 50µm).IntroductionDuring ironmaking and steelmaking, significant amounts of slag are produced. Contrast to the high utilization of ironmaking slag, the treatment of steelmaking slag is more difficult and challengeable, and therefore, an alternative approach is to recycle the steelmaking slag inside the ironmaking and steelmaking process itself. The main limitation to the reuse of steelmaking slag inside the process is that the refining process may be aggravated caused by the phosphorous accumulation if it is used in the blast furnace burden [1]. At the same time, the phosphorous content of steelmaking slag (approximately 1%~5% P2O5) is too low for it to be used as raw material for fertilizer [2, 3]. Moreover, owing to the diminishing supply of global iron ores with low phosphorous content, the control of phosphorus in iron and steelmaking processes has become an increasing problem, and as a result, more amounts of high phosphorus containing steelmaking slag are produced. Therefore, a valuable approach is quite appreciated in which the steelmaking slag is recycled within the ironmaking and steelmaking process and at the same time, the high phosphorus-containing phases in the steelmaking slag, suitable for use as fertilizer can be separated and recycled effectively [4]."

Jan 1, 2011

By Arthur E. Morris

The primary market driver for improving process technology is innovation, which requires a skilled and educated workforce. However, many Materials Science and Engineering departments have eliminated extractive metallurgy and chemical thermodynamics from their curricula, yet these topics contain the necessary fundamentals for process innovation. As a result, most MS&E students are ill-prepared for careers in processing. The dearth of processoriented MS&E curricula has prompted some Universities to develop a “shared” effort to offer distance education between multiple institutions [1]. A target audience for a shared process simulation course would not only benefit students, but also be a basis for an on-line course for practicing engineers faced with new or changing career choices. To fill the gap, the basics of a process simulation course was developed in an abbreviated form as series of eleven articles and Excel workbooks published in Industrial Heating magazine between July 2012 and July 2013.

Jan 1, 2014

By Per Anders Eidem, Merete Tangstad, Jens Davidsen

"During excavations of submerged arc furnaces producing silicomanganese, silicon carbide (SiC) has been found. Contributing to the size of the inactive area of the furnace, the active area of the furnace where reactions occur will decrease, thus reducing the potential for pre-reduction in the furnace.This work studied the formation of SiC from the liquid-solid reaction between slag, metal, and metallurgical coke. Slags and metals with different levels of silica (S1O2) and silicon (Si) have been studied. The slag and metal has been heated together with coke, and the samples investigated by microprobe. The results show that SiC was formed on the coke particle through reactions with both slag and metal. For the metal, the carbon most likely diffused through the SiC to react with Si in the alloy. SiC formation with slag is likely to go through the reduction of Si02 to Si.IntroductionToday, Silicomanganese (SiMn) is produced in submerged arc furnaces (SAF) by reduction of S1O2 and manganese oxides, mainly with metallurgical cokes. Typically, the tapped metal has a silicon content of 17 - 20 wt.%. To achieve higher levels of Si, the metal can be refined by adding off-grade silicon metal, yielding low carbon SiMn. [1]. What is believed to be SiC that has been found during dig-outs of SiMn furnaces producing high silicon alloy. It is possible that excess amounts of SiC in the furnace cause operational problems, since SiC will occupy furnace volume. As SiC accumulates, the active volume of the furnace will decrease, increasing the flow of material and gas in the active areas of the furnace. Formation of SiC is inevitable, so it is desired to keep the formation as low as possible. To be able to control the formation of SiC, one has to understand the basic mechanisms."

Jan 1, 2012

By P. Ruz

A melt transfer ladle was 3D modeled by means of a mathematical fluid dynamics and heat transfer program. Internal temperature profiles were calculated as a time function for a normal ladle and for a pre-heated refractory lined ladle. It was shown that in a normal ladle the molten metal cools down quickly forming accretions. By using an inner lining there are practically no accretions build up within a typical time of operation. Therefore, by applying a refractory lining to a melt transfer ladle and keeping it at a moderate to high temperature it is possible to reduce cold dope circulation in the smelter.

Jan 1, 1999

By Yoshihiko Maeda

It is said that the 21 st century will be an era of the remedy of the global environment. In order to reserve natural resources for the future and to avoid the dispersion of heavy metals after usage and to avoid pollution problems, it is extremely important to recycle heavy metals as much as possible by reasonable recovery procedures. The nonferrous metal industry is expected to play a important role in the recycling of heavy metals that are originally their products. From the depressed metal price experienced in Japan in 1980th due to the sudden change in current exchange rate between US dollar and Japanese yen, one of major nonferrous metal company, Dowa Mining, has diversified its business area not only to the so-called down stream, but also to the environmental business including metal recycling, industrial waste treatment and soil remediation by utilizing technologies and facilities once used or still used for mining and smelting of copper, zinc, lead and precious metals. In this paper some of these applications will be presented.

Jan 1, 2003

By R. M. Donovan

This paper documents the efforts to improve quality and production at the Amarillo Copper Refinery. It summarizes the change in attitudes, work procedures, equipment maintenance, instrumentation, and the ever changing market. The Amarillo Copper Refinery is dedicated to the ASARCO Management System, ISO-9002 and continuous improvement.

Jan 1, 1999

By M. Rosales

Using the k-e turbulence model, a mathematical fluid dynamics simulation of the flow characteristics in a Teniente converter has been conducted. Two cases were studied: - Transversal sections in the smelting-converting zone; and - A three-dimensional simulation that includes the walls of the reactor The calculations give the velocities field, the gravity waves amplitude, the splashing behaviour, the phase distribution and the shear stress distribution. The latter helps to explain the pattern of refractory lining wear. The calculation includes the approximate shape and dimensions, and the eventual coalescence of bubbles.

Jan 1, 1999

By Jeong-Hwan Kim

The liquid-liquid reactive process (solution process) is often adopted as a synthetic method for precipitated calcium carbonate (PCC) in laboratory studies for its simplicity in operation or ease in controlling process variables. Still, PCC are produced commercially by passing carbon dioxide through a milk of lime, i.e., by a gas-liquid reacting method (carbonation process). Few studies on the carbonation process have been conducted, since the process variables are interrelated and difficult to control compared to the solution process. In this study, both carbonation and solution processes were employed to study the polymorphs of calcium carbonate and growth rate of PCC crystals. The effects of the characteristics of limestone ores as a raw material in the synthetic system of PCC on the synthetic characteristics of PCC were also investigated. To control the nucleation rate in the synthetic systems, the shape factor was considered most important. Single-phase aragonite PCC could be synthesized under a variety of controlled experimental conditions such as ionic strength, solution composition, concentrations of additive ions, and temperature.

Jan 1, 2006

By E. Burgos Cruz

The behaviour of S, N and P during refining of Fe-18 wt%Cr-10 wt%Ni with calcium carbide was investigated. The effects of the initial contents of C and N in the metal phase, as well as the supply method of calcium carbide to the melt on the removal degrees of S and P were evaluated. Heats were carried out at 1873K, in MgO crucibles, using a laboratory induction furnace. It was observed that simultaneously with S and P, N and O have also participated in the reactions. It seems that, in fact, O governs the behaviour of the other elements dissolved in the melt and that N is had to the removal of P with calcium carbide. It was also noticed that high C content in the metal phase have not altered the dephosphorization and desuffirization degrees, but that the supply of calcium carbide done by injection led to a lower dephosphorization degree than the one obtained by dumping it.

Jan 1, 1995

By C. Geenen

At its Olen site, Union Minière Copper operates a new full-size deposit tank house. A first 200,000 t/y module was commissioned in October 1996, and an additional 130,000 t/y unit started in April 1998. The main objectives of the new tank house project were to produce grade A cathodes starting from anodes with a wide range of compositions and at a minimal operating cost. The tank house uses Isa Process technology. Based on the process parameters agreed upon with MIM, UM Copper developed the basic design and UM Engineering was the in-house contractor for the engineering. The new tank house is equipped with advanced technology polymer concrete cells, automated two-bale cranes and high-capacity machines. The first 200,000 t/y module treats anodes with a more conventional composition at 330 A/m2; the second 130,000 t/y module treats anodes with a high slimes fall (12- 13 kg/t) at current densities up to 285 A/m2. After some teething problems, the new tank house is meeting all set targets. This paper illustrates and comments on the design characteristics and operational results.

Jan 1, 1999

By John M. Rogers

Risk management has rapidly developed to become an integrated, holistic approach that now encompasses the main risk elements such as product quality control, occupational health and safety, security, environmental liability, social issues and related management information systems. Given the obvious economic benefits, a seamless blend of risk management components has become essential to allowing organisations to sustain a competitive advantage, and is also looked upon as an important attribute in organisational growth. Juxtaposed with this management philosophy is the global trend towards outsourcing, which has seen the emergence of independent, and specialist risk management organisations. The New Millennium will undoubtedly see a shift away from "in-house" risk management practices, and consequently, the selection of a suitable risk management partner - a major vehicle for improving shareholder value - will become an important strategic management decision.

Jan 1, 1999

By Daniel Kim, Ari Rantala

Efficient on-line monitoring of electrolytic cell performance in copper electro-refining has been challenging due to the need for complex electrical measurement systems and the management of the enormous volume of data. Based on Kennecott Utah Copper's innovation Outotec has developed a novel and innovative electrolytic cell monitoring system called CellSense™ System. As the system is based on self-powering from bus bars, wireless communication, on-line adaptive modeling and easy to access information and alarming, traditional obstacles of electrolytic cell monitoring are eliminated. With cell voltage and electrolyte temperature measurements, CellSense System enables real-time cell performance discovery and early reaction to critical production or quality disturbances such as short-circuiting, flow blockages, cold cathodes or electrolyte temperature excursions. During the past few years the system has been delivered to over 3500 commercial cells. In this paper the largest CellSense™ System ever delivered and recently adapted by Kennecott Utah Copper with 1412 cells monitored on-line for high tankhouse performance, cathode quality and optimized operator work flow is presented. Early results and benefits are discussed.

Jan 1, 2012

By A. Raraz

The optimization of the plutonium electrorefining process has been studied on the basis of modeling and model materials. The plutonium electrorefining process has been reviewed and the basics of the electrorefining process with molten salts as electrolytes and under forced convection has been presented. The definition of the problem in plutonium electrorefining has been related to three factors and this research has addressed these three factors to provide an insight to this process. The hydrodynamic factor gives information on the behavior of the mechanically stirred system. The chemical stability and solidification factor shows the interactions among the components of the electrorefining cell. The electrochemical factor is oriented to study the efficiency of the electrorefining process on the basis of limiting current density, stirring rate and configuration cell. As a result of this study the optimization of plutonium electrorefining implies mainly a re-design of the cell.

Jan 1, 1995

By G. Gomathi, K. Asokan, K. Subramanian

An electrochemical reactor with anode and cathode chambers separated by a composite perfluoro polymer cation exchange membrane was designed, fabricated and used for the reduction of dissolved carbon dioxide under ambient conditions to formate. The flow reactor enhanced the mass transfer of carbon dioxide compared to the batch reactor. Experiments were conducted using two different perfluoro polymer membranes - Nafion 961. Efficacy of CO2 reduction on various cathode materials (Cd, Pb, Sn and Zn plated stainless steel woven mesh) were determined. Optimum values of flow rate and current density were evaluated for the energy efficient formation of formate in aqueous KHCO3 (pH 7.5-8.5) buffer solutions.

Jan 1, 2008

By A. V. Tarasov, V. M. Paretsky

"The design is based on the thermal processing of the wastes in· the intensively bubbled melt in the Vanyukov furnace at the relatively high temperatures (1350- 1450 °C), In this case: -the secondary wastes are not formed; - the especially toxic substances at the outlet from the furnace are absent. The technology was tested on a large scale (on semicommersial bases). Technical and economical basis show profitability of recovery complex for processing of hard garbage waste (HGW) using this technology: the period of capital, investments refunding for the, recovery, complex construction with process annual capacity of 240 thousands tons of wastes is 1,5-2,5 years,"

Jan 1, 2000

By Victor Bredykhin

The reasons of formation low quality cathode deposits and conditions of the anode passivation in electrorefining of copper silver alloys with increased (more then 5%) silver content in electrolyte, g/l: Cu - 40; H2SO4-50; 150 and 250; T= 401C have been investigated. As it is shown, increased acidity, anodic current density and silver content in anodes favor passivation. The assumption is made that the ingress of silver on cathodeis the most probable reason of growing dendrites on cathode. We have determined that addition of ethylene carbonic acid to electrolyte in the amount of 3,5 ÷ 10 ml/l suppresses the dendrite formation.

Jan 1, 2006

By D. G. Schmidt

Tests were conducted on C86200 high-strength yellow brass in order to ascertain the effect of a low level of nickel on the mechanical properties on this alloy. A series of two alloys was studied, one of which had a nickel content of 0.85% and the other with <0.05% nickel. Copper and aluminum content ranged from 62.5% to 64% and 3.2% to 4.6%, respectively. When compared by zinc equivalents, a nickel addition of 0.75% in high-strength yellow brass does not act like copper but raises the tensile strength, 0.5% yield strength and BHN while lowering the elongation.

Jan 1, 1999

By A. N. Lasseigne

Hydrogen storage capabilities of LaNi5 intermetallic compounds were investigated utilizing the combination of thermoelectric power, Beeghly Ester-Halogen digestion, and Leco hydrogen determination. Thermoelectric power has demonstrated a rapid hydrogen assessment capability and can achieve the equivalent of the pressure-composition-temperature (activity) diagram. Effective use of hydrogen storage materials occurs in the two-phase, alpha+beta region of the PCT diagram. A thorough assessment of the content of each phase in this two-phase region to optimize performance of the hydrogen storage materials is described. Practices using the combination of these three analytical practices for rapid characterization of LaNi5intermetallic alloys are discussed.

Jan 1, 2006