Search Documents

By Pinnaduwa H. S. W. Kulatilake, Biao Shu

The intact rock properties and discontinuity properties for both Devonian Rodeo Creek (DRC) and Devonian Papovich (DP) rock formations that exist in the selected open-pit mine were determined from tests conducted on rock samples. Special survey equipment, which has a total station, laser scanner and a camera, was used to perform remote fracture mapping in the research area. From remote fracture mapping data, the fracture orientation, spacing and density were calculated using more refined procedures compared to what exist in the literature. Discontinuity orientation distributions obtained through remote fracture mapping agreed very well with the results of manual fracture mapping conducted by the mining company. The GSI rock quality system and Hoek-Brown failure criteria were used to estimate the rock mass properties combining the fracture mapping results with laboratory test results of intact rock samples. Fault properties and the DRC-DP contact properties were estimated based on the laboratory discontinuity test results. A geological model was built in a 3DEC model including all the major faults, DRC-DP contact and two stages of rock excavation. The built major discontinuity system of 44 faults in 3DEC with their real orientations, locations and three-dimensional extensions were validated successfully using the fault geometry data provided by the mining company using seven cross-sections. Numerical modeling was conducted to study the effect of boundary conditions and lateral stress ratio on the stability of the considered rock slope. For the considered section of the rock slope, the displacements obtained through stress boundary conditions seemed more realistic than those obtained through zero velocity boundary conditions (on all four lateral faces). Stable deformation distributions were obtained for k0 in the range of 0.4 to 0.7. Because the studied rock mass is quite stable, it seems that an appropriate range for k0 for this rock mass is between 0.4 and 0.7. The displacements occurred between July 2011 and July 2012 due to the nearby rock mass excavation that took place during the same period; they were compared between the field monitoring results available from the mining company and the predicted numerical modeling results and a good agreement was obtained. Overall, the successful simulation of the rock excavation during a certain time period indicated the possibility of using the procedure developed in this study to investigate rock slope stability with respect to expected future rock excavations in mine planning.

Jan 1, 2015

By Guo Wenbing

"INTRODUCTIONThere is a great amount of coal (about 140 billions tons) left unmined under the surface structures, water bodies, railways (referred to as the “three-body”). Coal mining under “threebody” especially that under surface structures has become a major problem in the mining area. The key problem of mining under surface structures is to control overburden strata and surface movements. At present, the major surface subsidence control methods are strip pillar mining, backfilling mining method, room and pillar mining, grouting of bed separations, harmonic mining, and so on. Wongawilli mining method is a high-efficient shortwall mining method developed based on the room and pillar mining, and named after the first successful trial in Australia “Wongawilli” coal seam. The room and pillar mining equipment such as continuous miner is employed in this method. Its major advantage is flexible face layout. It can be used to mine the small wedge coal blocks and those that are difficult to be mined with retreat longwall mining method. It requires less capital investment, short lead time for production, flexible equipment operation and face move and high productivity. It has been applied in some China’s coal mines.The “Wongawilli strip coal mining technology” is a new coal mining method for mining under surface structures. It combines the strip mining longwall layout and Wongawilli high efficient mining technology. This technology can fully utilize the advantages of both the strip pillar and Wongawilli mining methods, and overcomes the disadvantages such as frequent face move, and low mining efficiency in strip pillar mining, and poor ventilation condition and poor long-term stability problems of coal pillars. In this paper, the Wongawilli strip mining method was designed for Wangtaipu mine and its feasibility was studied using numerical modeling and surface subsidence prediction.Geological and mining conditionsAt present, most of the No.15 coal seam reserves totaling 377.07 million tons in Wangtaipu mine are located under surface structures. In order to mine the coal under the surface structures, the Wongawilli strip mining method was employed. An appropriate panel was selected for trial and the surface movement monitoring lines were set up. The trial area is located in panel XV2214 (East) ( re 1). In this area, the floor elevation of coal seam is +634~646m, the surface elevation is +810~817.5m, and the average depth of coal seam is about 174m.The average panel length is 282m and average panel width is 73.5m. The seam dips 1~3° and is 1.8~2.5m thick with an average of 2.15m. The roof and floor rock characteristics are shown in Table 1."

Jan 1, 2015

By Andre Zingano

An underground mine using room and pillar and retreat mining methods was developed during the 1950?s. In 2009 an open cast mine was opened in the same reserve with the objective of mining five coal seams including the one previously mined. Recently, a series of slope failures were detected at the open cast mine. The surface mine map was overlain on the underground mine map, and it was observed that the slope failures were located above a retreat mined area where the overburden had caved and the ground subsided. The deformation and displacement attributable to subsidence caused a loss of strength in the overburden strata. The objective of this paper is to study the causes of slope sliding (or failure) due to the ground subsidence of rock layers above oldmined out areas. A map was created to overlay the two mines -- the abandoned underground mine and the active surface mining. Two- and three-dimension numerical modeling was conducted to simulate the slope behavior and to verify whether the mine subsidence was the cause of slope instability. This study indicated that the subsided rock layers were the cause of slope instability and sliding.

Jan 1, 2013

By Adrian L. Moodie

Austar Coal Mine (formerly Southlands and Ellalong Collieries) has had a long association with difficult strata control conditions associated with mining depth and a highly jointed/cleated coal seam. The conditions include poor longwall face conditions, cyclic loading, heavy tailgate (TG) roadway conditions, and difficulties in maintaining stable roadways on development at 5.2 m (17 ft), as well as the geotechnical challenges of an 8.5-m (27.9 ft) -wide roadway required for installation faces. The introduction of Longwall Top Coal Caving (LTCC) to this environment has aided in the management of some of these issues, but LTCC has also given rise to other geotechnical considerations. Additional geotechnical issues associated with LTCC not only require management during operations, but also require consideration when evaluating new mining areas at Austar Coal Mine or potential LTCC extractable resources throughout Australia and the world. In September 2006, LTCC commenced at Austar Coal Mine in longwall panel A1. Since this point the LTCC face has been increased from 147 to 216 m (482 to 709 ft)and finally to 227 m (745 ft) in width, and it has also been rehanded and modified in the three fully extracted panels to date. The application of LTCC in panels A1, A2, A3, and now A4 has been very successful, both from a coal resource recovery point of view and in the management of the principal hazards of spontaneous combustion and strata control. This paper focuses on the geotechnical aspects of the application of LTCC at Austar Coal Mine and also reviews some advances in general strata control management at the mine.

Jan 1, 2011

By Yingda Zhai

The range of interburden thickness between coal seams in Datong Mining District of China is large. From mining operation point of view, the closer is between the two seams, the greater is the impact from the upper seam when the lower seam is mined. This impact is most notable when the two seams are ultra-close. In this paper the definition of ultra-close seams and its practical method of determination are presented. Based on the difference in strata thickness in the interburden and the concept of "yield depth ratio" which is defined as the yield zone depth in the interburden to the total thickness of interburden, the roofs of the ultra-close multiple seams in the Datong District of China were divided into 3 types: (1) false roof or rock partings in coal seam. This type of roof does not require special handling except mining them simultaneously as one single seam. The roof thickness is slightly less than 0.5 m; (2) completely broken roof. In this type of roof, the yield depth ratio is larger than (or equal to) 1. When the roof thickness is larger than 0.5 m but less than 2.0 m, the yield depth ratio must be smaller than 1; and (3) fractured roof. In this type of roof, the yield depth ratio is less than 1 while the roof thickness is larger than 2.0 m. In retreat longwall mining, if the gateroads of the lower seam are located under the gob of upper seam, roof bolting can be used in the 3rd type of roof. But if the 2nd type roof exists, powered supports must be used.

Jan 1, 2005

By Shosei Serata

Serious floor heave of up to 2.4 m in a 2.4-m high mine entry was eliminated by applying the stress control method of mining, as a last resort, at the No. 5 coal mine of Jim Walter Resources, Inc., in the Black Warrior coal basin near Birmingham. Alabama. Underground observation of the first 3-room entry created using the stress control method is discussed here. The behavior of the test entry, which eliminated the heave problem, is analyzed in relation to similar studies conducted in a salt mine under similar ground conditions by utilizing finite element analysis.

Jan 1, 1984

By Liang Dong, Jinxuan Liu, Biao Qiu, Jing Chai

"The Cenozoic unconsolidated strata in the east area of China are composed of clay, sandy clay, fine sand, hardpan, etc. Numerous shafts of the coal mines in these areas have been damaged in various degrees since 1987. The main reason for this disaster is the vertical additional stress on shaft caused by the subsidence of the thick unconsolidated strata. In order to monitor the subsidence deformation of the unconsolidated strata, a sensing network system with multiplexed Fiber Bragg Grating (FBG) for monitoring settlement deformation of the unconsolidated strata in deep borehole is proposed. The field monitoring results show that, soil layers settle or expand with decrease or increase in ground water levels. The thick hardpan generates the main compressive deformation. This FBG strain monitoring method can take place of traditional ground water measuring method. This system is stable and reliable, and the monitoring results can show the subsidence deformation of different layers, which has significance for the predictive maintenance of the shafts.INTRODUCTIONSince 1980s, a specific geologic hazard has occurred frequently on the coal mine shafts in eastern China: non-mining-induced shaft deformation, involving up to 100 shafts located in Jiangsu, Shandong, Anhui and Herran province, distributed in Xuzhou, Datun, Huainan, Huaibei, Yanzhou and Yongxia coal fields. This kind of geologic hazard can lead to shaft wall deformation, water infiltration, cage stuck, water-sand burst or shutting down of coal mines, which seriously risks the coal mines. Zhangshuanglou coal mine, Haizi coal mine and Linhuan coal mine shut down for 2-8 months due to this hazard (Chen, 1997; Cui, 1998). The main reason for this geologic hazard is the subsidence of the super thick unconsolidated strata (Liu et al., 2007; Xu et al., 2006).An innovative structure health ·monitoring and damage estimation method has been developed in recent years, i.e., optical fiber smart material and structure (Nobuo, 2002; Wang et al., 2000). A Fiber Bragg grating (FBG) sensor is a device that can transfer the change of the measured strain or temperature to the change of Bragg wavelength. One of the most important applications of FBG sensors is to monitor the internal stress and strain distribution of material and structure (Philipp et al., 2000; Ansari et al., 1998). Compared to traditional electrical sensors, FBG sensors have many advantages; they are adaptable to harsh environments, abrasion resistant, immune to electrical magnetism (EM) interference, safe and reliable. They also offer integrated sensing and transmission on a single fiber, have simple structure and are convenient to use, which satisfies the requirements of long distance, distributional and long term use in monitoring mining and geotechnical engineering structure. Due to such advantages, the FBG sensor has already been applied in petroleum engineering (Kersey, 2000), rock mechanics testing (Cornelia et al., 2003; Yang et al., 2007; Wei et al., 2008), physical simulation experiments (Chai et al., 2007; Chai et al., 2006; Zhu et al., 2008; Li et al., 2008; Chang et al., 2008), strain sensor (Li et al., 2007; Chai et al., 2008) and construction structure damage diagnosis (Dong et al., 2004; Kerrouche et al., 2008; Whitten et al., 2001)."

Jan 1, 2010

By Peter Zhang, Gary Deemer, Rod Lawrence, Scott Peterson, Scott Wade, Mike Mishra, Rick Smith, Robert Bottegal, Ed Zeglen

"Thinly-laminated silty shale that falls like ""stack rock"" is always difficult to support in underground coal mines. With thin laminations of 2.5 to 52 mm (0.1 to 2 in) thick and weak bonding between laminations, the roof is much weaker under horizontal stress than under vertical load. Buckling of thin laminations and cutters are common signs of initial failure for this type of roof. When a roof fall occurs, it is mostly above the primary bolted horizon with a fiat top and steep breaking angle above the pillar ribs. Because silty shale is brittle, roof falls mostly develop without significant roof sagging. With thick, laminated silty shale, it is difficult to build a strong solid beam with short primary bolts. Longer bolts, straps, and supplementary cable bolts are required. Since installation of longer primary bolts in low seam mining is operationally inefficient, supplementary bolting is important to maintain overall roof stability. The bolting plan should also be chosen based on the geologic hazard map, which indicates the distribution and thickness of laminated silty shale, as well as the transition areas.To effectively support the thinly-laminated silty shale roof, an area with the same type of roof in a low seam mine was monitored for approximately four months. The mine had experienced roof falls while using different bolting systems and mine orientations in past years. The roof support in the area was studied through geologic mapping, roof scoping, and testing of different bolting plans. This paper presents the roof failure characteristics of the thinly-laminated silty shale, the correlation between failure and geologic condition, an evaluation of different bolting plans, and the requirements for primary and supplementary bolting for the silty shale roof.INTRODUCTIONThinly-laminated silty shale that falls like ""stack rock"" is always difficult to support in underground coal mines (Peng, 2007). With thin laminations of 2.5 to 52 mm (0.1 to 2 in) thick and weak bonding between laminations, the roof is much weaker under horizontal stress than under vertical load. Buckling of thin laminations and cutters are common signs of initial failure for this type of roof. When a roof fall occurs, it is mostly above the primary bolted horizon with a fiat top and steep breaking angle above the pillar ribs. Because silty shale is brittle, roof falls mostly develop without significant roof sagging. In low seam mining, it is difficult to install longer primary bolts, so supplementary bolts have to be installed to maintain overall roof stability. To effectively support the thinly-laminated silty shale roof, an area with the same type of roof in a low seam mine in western Pennsylvania was studied for approximately four months."

Jan 1, 2010

By Hongwei Zhang, Sen Yang, Shimin Liu

"This laboratory study investigates the damage evolution of sandstone specimens under two types of cyclic loading conditions through monitoring and analyzing the variations of elastic moduli and ultrasonic velocities. We adopted the rigidity degradation method for evaluating the damage accumulation through the rock dynamic ultrasonic velocity measurements. Compared to the ultrasonic test, the method of rigidity degradation shows deficiencies in the detection of damage development. The cyclic loading within the elastic limit led to a stiffening trend for the loading process but a softening trend for unloading process. The method of rigidity degradation was unable to describe the damage accumulation in this situation, while P-wave velocity clearly reflected the damage development. Moreover, a simplified model is established for interpreting the behaviors of the modulus variations and ultrasonic velocity. The cyclic loading within elastic limit enhances the anisotropy of rock, which causes a denser packing pattern in the direction of axial stress. The persistent damage accumulation under the cycling with an increasing upper limit is the consequence of the tensile failure in the microstructure of sandstone. INTRODUCTION The damage accumulation due to dynamic (cyclic) loading is highly detrimental in many engineering structures, such as mine openings, petroleum and natural gas boreholes, tunnels, rock foundations, and underground chambers. The sources of cyclic or repetitive loadings can be roughly divided into two types: (1) periodic operation, including drilling, blasting, and mining; (2) random vibration, including earthquakes and traffic loads. The repetitive loading-unloading process opens and closes the micro-pores and micro-cracks within the rock, further inducing the growth of cracks. As expected, the accumulating damage becomes a potential factor to trigger the rapid and violent failures of large-scale engineering rock structure."

Jan 1, 2017

By Ashok Kumar, Rajendra Singh, Petr Waclawik

High-grade coal is locked in the shaft protective pillars at 900 m below surface in the Czech part of Upper Silesian Coal Basin. To optimise recovery of coal from the larger size shaft protective pillar, room and pillar (called bord and pillar in India) is trialled to further develop these on smaller pillars. This development followed a constant gallery width of 5.2 m and 3.5 m height. The monitored pillar size in the first developed panel varied from 860 m2 to 1225 m2 of area. The stability of these pillars (i.e., natural supports) at this depth of cover is observed to be a vital issue to control ground movement and safety of the surface structures. A simple calculation of safety factor revealed that application of an empirical method for estimating size and shape of the pillar is inappropriate due to complex geo-mining conditions of the site. Accordingly, geo-technical instruments are installed in the panel for monitoring the stability of the diamond shaped pillar at different stages of the development. Extensive monitoring of the pillar behaviour by these instruments provided an important set of data for such optimum recovery. An established process of simulation-based pillar strength estimation is often used by the mining industry, but calibration is generally done with the help of empirical formulation. However, for the deep-seated pillar, the strength suggested by the existing empirical formulations (except the CMRI formula) is found to be much different from the instrument observations. Using a study conducted at Czech hard coal mines, an attempt is made to develop a strain-softening-based numerical modelling approach to assess pillar performance at deeper cover. The recorded value and nature of the pillar spalling in the field along with the CMRI formula are used to calibrate the developed simulation approach. An assessment of the stability of the developed pillars using simulated models did not indicate any collapse of the natural supports. This paper briefly presents difficulties in pillar design at great depth of cover and field and simulation results of pillar strength estimation in Czech hard coal mines.

Jan 1, 2018

By Yao Yuping

The strength and deformation of more than two hundred coal samples have been tested in the condition of triaxial compression. The regression equation showing the relationship between coal strength and pressure in the pores as well as confining pressure, was obtained. The appropriate calculation for stress-strain curve was carried out. Further, an analysis shows the variation of coal strength and its modulus of elasticity in methane medium.

Jan 1, 1992

By Joel Bradley, Kot Unrug, Kyle Perry, Mark Klimek

"A West Kentucky mine operation in No. 11 seam, encountered floor heave, due to the localized increase of the thickness in the fireclay mine floor. Floor heave has overridden seals installed in two mined out panels. The third seal’s location was planned for isolating that area from the Mains. A plan of support has been developed to prevent repetition of the floor heave and related problems outby the seals. The applied ground control measures were successful. An attempt of a 3D numerical modeling was made, that it would match the observed behavior of the mine floor and could be used as a design tool in similar conditions. In the paper described are sequence of events, a mitigation ground control system applied, and the first stage of numerical modeling.IntroductionWest Kentucky coal mine operation in the No. 11 seam has approached an area where the fireclay floor thickness increases to about 5 ft. Delayed floor heave has been observed. In the first sealed area (Panel KK), floor heave has overridden the seals and has begun to progress outby. This could not be allowed at the new seal location PP described in this paper because such override would affect the mains. Previously numbers of standing support systems were used, but their effectiveness was not satisfactory as is illustrated in Figure 1, Figure 2, and Figure 3. Therefore, with sealing of the next area approaching, mine management was looking for a better solution that would eliminate the problem. In that stage, our team looked closely at the geology and strength of roof and floor, as well as the characteristics of ground failure around the seal at the first site. The technical literature has been searched as well Haramy et al. 1986 Hsiung and Peng 1987, Peng 2008, Santos & Bieniawski 1987. This led to the identification of factors responsible for the ground failure. It has been determined that increased fireclay thickness from typically less than 2 ft to about 5 ft, when compared to the previously mined parts of reserve, and the strong limestone strata just above the immediate roof composed of 2 ft of black shale, created conditions of failure. It appeared that, when pillars were punching into the mine floor, the strong roof did not break but was bending, exerting high pressure on outby pillars, causing rib failures and closure. This is a similar mechanism to a strong roof affecting longwall shields. The remedial action planned was additional support."

Jan 1, 2015

By A. Chrzanowski

The integrated approach to monitoring surveys is based on a simultaneous utilization of geodetic, photogrammetric and geotechnical measurements of displacements, tilts, strains and any other geometrical parameters of deformation. New techniques for the integrated surveys are being developed at the University of New Brunswick in cooperation with the Canada Centre for Mineral and Energy Technology. A telemetry system for continuous monitoring of geotechnical measurements under difficult climatic and topographic conditions has been constructed and successfully tested in a coal mining area in western Canada. A generalized method for analysing the integrated deformation measurements has been developed and applied in the test area to yield three dimensional empirical modelling of surface movements from geodetic, photogrammetric and tilt surveys. The most appropriate model can be chosen from a statistical assessment of several modelling possibilities. The empirical model of the deformation can be employed in a "calibration" of the prediction (deterministic) model of the ground movements. A computer programme for two- and three-dimensional finite element modelling of elasto-plastic deformations has been developed at UNB as a part of the integrated approach. The :EM has been tested in predicting deformation in the test area in difficult geological conditions which were associated with an extraction of a steeply inclined coal seam. The results gave good agreement with the actual displacements obtained from geodetic measurements and confirmed the existence of a suspected fault.

Jan 1, 1984

By Jessica M. Wempen, Michael K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DlnSAR), a satellite-based remote sensing technique, has potential application for measuring mine subsidence on a regional scale with high spatial and temporal resolutions. However, the characteristics of Synthetic Aperture Radar (SAR) data and the effectiveness of DlnSAR for subsidence monitoring depend on the radar band (wavelength). This study evaluates the effectiveness of DinSAR for monitoring subsidence due to longwall mining in central Utah using L-band (24 cm wavelength) SAR data from the Advanced Land Observing Satellite (ALOS) and X-band (3 cm wavelength) SAR data from the TerraSAR-X mission.In the Wasatch Plateau region of central Utah, which is characterized by steep terrain and variable ground cover conditions, areas affected by longwall mine subsidence are identifiable using both L-band and X-band DlnSAR. Generally, using L-band data, subsidence magnitudes are measurable. Compared to X-band, L-band data are less affected by signal saturation due to large deformation gradients and by temporal decorrelation due to changes in the surface conditions over time. The L-band data tend to be stable over relatively long periods (months). Short wavelength X-band data are strongly affected by signal saturation and temporal decorrelation, but regions of subsidence are typically identifiable over short periods (days). Additionally, though subsidence magnitudes are difficult to precisely measure in the central Utah region using X-band data, they can often be reasonably estimated.INTRODUCTIONDifferential Interferometric Synthetic Aperture Radar (DlnSAR) is a satellite-based remote technique that can be used to measure surface displacement over large regions with high spatial resolution. Under good conditions, displacements can be measured with centimeter to subcentimeter accuracy (Buckley, 2000; Massonnet and Feig!, 1998). DlnSAR also has high temporal resolution, and imaging periods typically range from 10 to 50 days (Rosenqvist, Shimada, and Watanabe, 2004; Roth, 2004). In the last two decades, the application of DlnSAR for mine subsidence monitoring has been demonstrated in coal basins in Europe, Australia, China, and the United States (Camec and Delacourt, 2000; Ge, Chang, and Rizos, 2007; Ge et al., 2008; Ismaya and Donovan, 2012; Ng et al., 2010; Perski, 2000; Perski and Jura, 2003; Popiolek and Krawczyk, 2006; Wegmuller et al., 2005; Wright and Stow, 1999; Zhao et al., 2014; Xinglin et al., 2014). Overall, these studies have demonstrated good data resolution, strong relationships between mine development and subsidence, and reasonable agreement between displacements measured by DinSAR and displacements measured by conventional surveys."

Jan 1, 2016

By Kousick Biswas

The main objective of occupational health and safety research is to minimize or eliminate the events that may cause fatal or non¬fatal injuries to human workers. A commonly used technique is to devise an "incident prevention plan", which is more often the product of thorough investigations of past reported incident events. Incident documentation and methodical reporting and systematic and thorough data collection, often help identify the root cause of the incident - in other words, the etiology of the incident. These retrospective analyses of the incidents can efficiently identify the future steps to take to achieve the objective of minimizing occurrence of "events of interest". This paper introduces a novel technique - "Taxonomic Analysis", which identifies the root causes of an event (an incident in this case) and can provide future direction for corrective measures to reduce the probability of occurrence of the event. A taxonomic analysis involves systematic and organization of data based on observation, description, and classification. This paper utilizes the rock fall related incident narratives, available with the Mine Safety and Health Administration (MSHA) database (1984¬1999), for a taxonomic analysis. The study found that 67.6% of groundfall incidents occurred in supported areas with the remainder (32.4%) in unsupported areas. Some form of rock mass failure appears to cause about 50% of groundfall incidents, although in 39.7% of the overall groundfall incidents or two-thirds of those involving rock mass failure, the exact nature of the rock mass failure could not be determined from the narratives. Human activities factors such as scaling or barring down, drilling or bolting, and setting timbers or cribbing accounted for another 34.5% of the groundfall incidents. Finally, support system failures made up the remaining 15.5%. Results from this taxonomic analysis may suggest focus areas toward which preventive measures and future research activities could concentrate.

Jan 1, 2003

By Yongping Wu

Roadway deformation and stress migration occur with uncertainty and randomness because of geology, tunneling and mining influence. In order to study the surrounding rock deformation and failure mechanisms in three-dimensional stress state, an air return roadway of Yuanyang Lake mine of Shenhua Ningxia Coal Industry Group Co., Ltd. was chosen as a research object. The three-dimensional model was a designed and completed experiment with a dynamic-static coupling load. The model was loaded by hydraulic cylinder, simulating the in-situ rock stress field and the induced stress field of surrounding rock. The deformation monitoring system of the roadway model was constituted by optical total stations, borehole observation instruments, acoustic emission monitoring, and stress sensors. A wealth of data was obtained through an omni observation of surface displacement, characteristics of stress distribution, and deformation and failure of surrounding model material. By acoustic-optic-electric methods, a real-time testing on physical, mechanical, and damage parameters was realized through the experimental process. The results showed that the data of deformation and failure obtained from the deformation monitoring system of the roadway were authentic, which has great significance for warning and forecasting safety hazards of surrounding rock in coal mines.

Jan 1, 2013

By David F. Gearhart

A cooperative study was conducted between Signal Peak Energy and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the behavior of a pre-driven recovery room under less than 200 ft of cover. The design of the support systems for a pre-driven recovery room must provide control of the roof and ribs during the changing stress environment experienced throughout the final advance of the longwall into the recovery room. It must also provide a stable area where mine personnel are not exposed to undue hazards during shield recovery operations. This recovery room was constructed in two phases; each phase mined a 21-ft-wide room that was heavily supported, and subsequently fully backfilled with 800-psi, cellular concrete. Instrumentation to monitor the recovery room performance included borehole pressure cells (BPCs) placed in the head gate and tailgate pillars, at four locations across the longwall panel, in the fill material, and in the first row of outby pillars near the center of the panel. Four roof-to-floor convergence sensors were installed in the back fill material and a vertical, multipoint borehole extensometer (MPBX) measured the displacement of the strata above the recovery room. Surface surveys were conducted to measure MPBX collar movement. The data show that the front abutment load was transferred onto the recovery room backfill and the out by pillars as the longwall panel was extracted. As the longwall approached the recovery area, the fender and shields yielded, but the backfill provided enough support to keep the room stable as the longwall advanced to its final position. The system worked as planned and the face was recovered in record time.

Jan 1, 2014

By Joao Felipe Costa, Jair C. Koppe, Andre Zingano, Cleber Gomes

"Run-of-mine Brazilian coal has high ash content and low calorific power. Therefore, the coal must be washed to achieve the power plant specifications for burning coal. A large amount of waste results from the coal preparation, and it must be disposed of in waste piles or waste dams, depending on the material size. These waste disposals are the cause of serious environmental problems, not only in the short and medium terms, but mainly in the long term, due to the risk of provoking acid drainage or spontaneous combustion. Waste disposal requirements also demand large areas. Other problems include the pillar and roof stability in abandoned and mined out areas, building of edifices on the old and active mines, and mining under urban areas. To solve these problems simultaneously, backfilling the entries in mined out areas began with two objectives: to understand the mechanical behavior of the filling material and to model the backfilling of room-and-pillar coal mine entries through numerical simulation. Laboratory tests were performed for different filling material (with and without cement) to determine its mechanical properties and failure criteria. Based on this study, it was possible to conclude that the backfill method is a good strategy to improve the ground stability in room-and-pillar coal mines for the long term, especially for weak coal seams, and to reduce the quantity of material on waste piles on the surface.INTRODUCTIONRun-of-mine (ROM) Brazilian coal has high ash content and low calorific power. Therefore, the coal must be washed to achieve the power plant specifications for burning coal. Two types of waste are associated with power plants that bum coal for energy generation: 1) the waste from the coal preparation plant and 2) the ash from the power plant after coal burning.The Brazilian coal ash content in the ROM coal is between 45 and 55%. The clean coal is 20 to 30% ash for 4,500 kcal/kg (18,000 BTU). The coal preparation plant recovery is only about 35%. Santa Catarina State (SC) produces about 7 million tons/year of ROM coal, which results in a total of 4.5 million tons of waste. This is a large amount of waste that must be disposed of in waste piles or waste dams, depending on the material size. The waste and ash content is represented by silicate materials, such as clay and sand, and by sulfide materials, like pyrite and organic sulfur (between 1and5%)."

Jan 1, 2010

By Zbigniew Lubosik, Stanislaw Prusek

"The main elements of hard coal extraction systems in the Polish mining industry, including the characteristics of gateroads, are described, followed by several dozen underground measurements of gateroad roof sag performed in different geological and mining conditions in Upper Silesia Coal Basin.Based on the analysis of the roof sag measurements, an attempt to describe the gateroad roof sag process using a geometrical model was made. To build the model, it was assumed that the roof sag curve could be described by three straight lines. The first line describes the roof sag ahead of the longwall face; the second line, the sag at the longwall-gateroad junction zone; and the last line describes the zone behind the longwall face. Determining the intersection points and inclination angles is essential for the model. These model parameters depend on the geological and mining conditions in the gateroad.Using the statistical computations and analysis, the dependencies between the characteristic points of the gateroad roof sag model and the selected geological and mining parameters were defined. The STATISTICA computer program by StatSoft was used for computation.This paper presents a simple form of the geometrical description of roadway roof sag progression that is very useful during the gateroad support design process.INTRODUCTIONThe longwall system with caving is the dominant method in European mining in cases of hard coal seam extraction. For instance, in Poland, in 2009, 117 longwalls were driven, with total production of 77.5 million tonnes. In roughly 95% of the longwalls, mining operations were conducted using longwalls with roof caving; the remaining 5% used the hydraulic stowing system. The average mining depth was about 700 m (2,297 ft), and average daily output per face was approximately 2,600 tonnes per day. When using the longwall mining system, gateroads play an important role. These principal roadways transport materials, mine crews, and output. In addition, they impact ventilation of the extraction area, affecting, among other things, the climatic conditions or methane hazard. Unfortunately, difficulties often appear in maintaining an adequate size for the gateroads, due to the face line, which causes origination zones with stress concentration around the gateroad, resulting in rock mass movements in the form ofroofsag, floor heave, or horizontal convergence (Figure 1)."

Jan 1, 2010

By Tulu B. Ihsan, Mark A. Van Dyke, Ted M. Klemetti

"How well do current modeling procedures calculate the rear abutment extent and loading? Does an improved understanding of the rear abutment extent warrant a change in standing support in bleeder entries? What is the optimal standing support for bleeder entries separated from the longwall startup room by a barrier pillar? To help answer these questions and to determine the current utilization of standing support in bleeder entries, four bleeder entries at varying distances from the startup room were instrumented, observed, and numerically modeled. This evaluation was intended to determine the rear abutment extent and magnitude at various locations to optimize standing support in these entries and those under similar conditions. This paper details observations made by NIOSH researchers in the bleeder entries of a deep cover longwall panel; specifically data collected from instrumented pumpable cribs, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was on the extent and magnitude of the abutment loading experienced by the standing support. As expected, the instrumentation of the standing supports showed very little loading relative to the capacity of the standing supports—less than 25 tons load and 1 inch convergence. The observations of the conditions showed little to no change from before the longwall panel extraction began to when the panel was more than 50% extracted. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the bleeder design. The Flac3D program was used to evaluate these four bleeder entries using previously defined modeling and input parameter estimation procedures. The results indicated only a minor increase in load during the extraction of the longwall panel. The model showed a much greater increase in stress due to the development of the gateroad and bleeder entries, with about 80% of the increase associated with development and 20% with longwall extraction. The Flac3D model showed very good correlation between expected gateroad loading during panel extraction and those expected based on previous studies. The front and side abutment extent modeled was very similar to observations from this and previous panels with similar conditions. The results of this study showed that the rear abutment stress experienced by this bleeder entry design was minimal. The convergence measured in these bleeder entries was small enough not to mandate any additional support beyond development even by U.S. or Australian standards. The pumpable crib load and convergence experienced depends on the geological setting, mining geometries, and timing. The farther away from the startup room, the lower the applied load and smaller the convergence in the entry if all else is held constant. Finally, the numerical modeling method used in this study was capable of replicating the expected and measured results near seam."

Jan 1, 2017