Search Documents

By Jon Y. Kaneshiro, Ed Walton, Stephen J. Navin, Robert M. Sergeant, Storer J. Boone

The Coronado Traffic Tunnel is a proposed two-lane, reversible, road tunnel, which will relieve severe peak hour congestion problems on surface streets. The tunnel will take traffic from the Coronado Bay Bridge to Naval Air Station North Island. The project will include 12.5 m (41 ft) inside diameter by 1,112 m (3,650 ft) of tunnel, 552 m(1,815 ft) of cut and cover box structure, and 400 m (1,315 ft) of open cut structure. The geology consists of predominately clean and silty sand, saturated sand, with some clay layers, requiring Earth Pressure Balance or Slurry Shield tunneling technology.

Jan 1, 2001

By V. Gall, J. Rudolf

The Virginia Department of Rail and Public Transportation and the Metropolitan Washington Airports Authority are undertaking the extension of Washington Metropolitan Area Transit Authority’s Metrorail service to Washington Dulles International Airport and beyond to Route 772 in Loudoun County, Virginia. The roughly 37 kilometers long, double track alignment involves two 700 meters long single track, soft ground NATM tunnels at Tysons Corner, two 3.3 kilometers long single track rock TBM tunnels at Dulles Airport and one 25-meter deep station at the airport to be constructed by NATM in sedimentary rock. The design-build project is being implemented in a Public-Private-Partnership. A joint venture of Bechtel and Washington Group International has concluded the preliminary engineering and construction is scheduled to start in late 2007.

Jan 1, 2007

By Chen Lin

Tectonic stress is an important parameter for understanding the dynamics of underground engineering and for the exploitation of coalbed methane. Multiple-period structural features usually have complex spatial relationships in tectonic superposition areas, which provides evidence for identification of the sequence of the tectonic stress period. Conjugated joints and slickensides are used to reconstruct the tectonic stress of the No. 8 Mine in Pingdingshan. Based on the geological unit division and field measurements, data on hundreds of joints and slickensides are collected from 33 stations. The tectonic stress results indicated by the conjugated joints show that there are mainly four directions of tectonic stress: NEE-SWW, NW-SE, NE-SW, and NNESSW. The tectonic stress results of the slickensides indicate that there are mainly four directions of tectonic stress: NNE-SSW, NNW-SSE, NEE-SWW, and NW-SE. According to the systematic analysis of the joints and slickensides, this paper separates the superposed joint and slickenside sets and identifies the tectonic stress periods with their abutting relationships. Three tectonic stress periods are determined and the sequence of the tectonic stress periods is NE-SW, NW-SE, and NEE-SWW. The results are consistent with other tectonic stress measurements for both the region and the locality.

By Chen Lin

Tectonic stress is an important parameter for understanding the dynamics of underground engineering and for the exploitation of coalbed methane. Multiple-period structural features usually have complex spatial relationships in tectonic superposition areas, which provides evidence for identification of the sequence of the tectonic stress period. Conjugated joints and slickensides are used to reconstruct the tectonic stress of the No. 8 Mine in Pingdingshan. Based on the geological unit division and field measurements, data on hundreds of joints and slickensides are collected from 33 stations. The tectonic stress results indicated by the conjugated joints show that there are mainly four directions of tectonic stress: NEE-SWW, NW-SE, NE-SW, and NNESSW. The tectonic stress results of the slickensides indicate that there are mainly four directions of tectonic stress: NNE-SSW, NNW-SSE, NEE-SWW, and NW-SE. According to the systematic analysis of the joints and slickensides, this paper separates the superposed joint and slickenside sets and identifies the tectonic stress periods with their abutting relationships. Three tectonic stress periods are determined and the sequence of the tectonic stress periods is NE-SW, NW-SE, and NEE-SWW. The results are consistent with other tectonic stress measurements for both the region and the locality.

By Nikhil Dhawan, Ashwini Kumar, Yogendra Pratap, Himanshu Tanvar

India does not possess any soluble potash reserves and depends completely on imports. In this study, an attempt has been made to recover potash (K) values from the mica sample employing thermal and mechanical routes followed by leaching. Direct leaching of mica in different lixiviants is found to be ineffective with very low K-dissolution (1–5%). Heat treatment with different fluxes, such as NaCl, NaOH, and CaCl2, is carried out and almost 85% K-values are recovered. Mechanical activation of mica and with different calcium additives is carried out to recover potash values. K is recovered in leach solution in the form of soluble salts, such as K2CO3, K2SO4, and KOH, and leach residue consists mainly of calcium-alumino-silicates. Using mechanical activation with flux, it is possible to recover >95% K-values from mica sample. Mechanical activation with calcium-based flux is found sustainable in the recovery of K-values from mica.

By Y. Paul Chugh

NIOSH and the Illinois Clean Coal Institute are funding studies on characterization of coal and quartz dust in Interior Basin mines since 2009. Coal dust characteristics vary significantly and, are vital for the development of the engineering controls. This paper presents wettability characteristics of coal dust with respect to its chemical and physical properties, since wettability is considered to be a primary dust control technique. Particle size distribution, inter-particle interactions during wetting and quartz associations with organic and inorganic matter in coal seams is critical for understanding wetting phenomena. Silica content in the un-wetted fractions was found to be very high during wetting tests. Wetting of quartz may be limited by its association to hydrophobic materials as well as buoyancy forces resulting from particle size characteristics and particle-particle interaction in the wetting agent. Temperature of the wetting solution and effective contact time between dust particles and water droplets are found to be two important variables affecting the wettability. The characterization data obtained from this study can be utilized to develop engineering controls.

Jan 1, 2011

By D. R. Dolinar

Geogrids can be used as surface control on both the roof and rib in underground mines to prevent the fall of small pieces of rock and material from between the primary supports. The use of screen material such as geogrid can significantly reduce the number of ground fall injuries caused by these small rock falls. Because of the potential for reducing injuries through the use of screen, the National Institute for Occupational Safety and Health (NIOSH) has conducted tests on screen materials including geogrid to determine their support characteristics and identify parameters that can affect their performance with respect to maintaining broken or failed rock. A specially designed test frame installed in the NIOSH Mine Roof Simulator (MRS) has been used to evaluate the load and stiffness characteristics of the screen material. Two types of geogrids with various designs have been tested-a polyester yarn and a polypropylene grid. The load-displacement characteristics of these grids were determined and the load capacity and stiffness were calculated through 20in of displacement. The load capacity and stiffness of the geogrid in general are shown to be related to the ultimate tensile strength of the screen material.

Feb 27, 2013

By Y. Q. Zhang, S. S. Peng

Numerical modeling was used to design the pillars and bolting plan for a mine with weak roof and multi-seam stress condition. Previous mining experience, pillar/roof yielding and in-situ horizontal stress were considered in the models. By modeling the upper seam yielding and vertical stress transfer, a multi-seam influence zone was obtained. Appropriate pillar sizes were designed for conditions with and without upper seam stress influences. Roof support for the track and belt entries, using fully-grouted resin bolts and cable bolts, was proposed and implemented in the model. The bolting plan was evaluated under the weak roof condition.

Jan 1, 2004

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a roomand-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90%. But, the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing oversprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99% and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber.

By Tom Szaraz, Steve Skelhorn

Part of a major sewer expansion for the City of Columbus, Ohio. The Big Walnut Outfall Augmentation Sewer (BWOAS) consists of 4,000m (13,200 ft) of 3.66m (12 ft)diameter tunnel passing mainly through glacial deposits with a water head of up to 2 bar. The project involves many new innovations, including: Slurry wall work shaft with excavation below the water table; Hybrid universal rings combining traditional steel reinforcement with fibers; New, full EPB Lovat TBM; Two component grout system pumped to the TBM from the surface; and, Linabond corrosion protection liner. The paper looks at the planning approach adopted to meet the various challenges presented, combined with an overview of progress to date.

Jan 1, 2007

By Leonard Weixler, Peter Halbach, Michael Jarowinsky, Johannes Post

Germany as an industrial nation is highly dependent on the import of mineral or metal resources. Sources which have not been considered until now are the marine mineral resources (MMR), which in recent times are enjoying more and more increasing interests and which might provide in the future a considerable contribution to the supply security on metal resources not only for the industrial countries. Backed up by the German government’s "National Masterplan Maritime Technologies" (NMMT) and corresponding industrial R&D-activities, the idea and the advantages of deep-sea mining is gaining more and more interests and supporters with respect to industrial and political considerations on strategic raw material resources as well as on the development of deep-sea mining technologies. The NMMT aims to initiate growth and increase the competitiveness of the German maritime industry on international markets and covers about 10 different marine and ocean technology sectors including deep-sea mining.

Sep 1, 2014

In bump-prone coal mines, roof and rib support is subject to dynamic as well as static loading. Although less frequently encountered, the dynamic loading component can result in violent coal expulsions into openings seriously threatening the safety of workers. Dynamic support systems that have been increasingly implemented in many deep hard rock mines for dynamic failure containment have not yet found their adaptation to deep coal mines at desired levels. This paper examines the potential use of some of these dynamic support systems in deep coal mining, particularly in the western United States. Fundamental principles of dynamic loading are reviewed in the context of their application to dynamic failure mechanisms in coal mines. Potential benefits and applicability of the suitable hard rock dynamic support systems are discussed in relation to coal bump mitigation. The resulting insight provides a starting point for development of dynamic support elements for bump prone conditions in deep coal mines.

Jan 1, 2009

By Kwangmin Kim, Junnhyeok Park, Taehee Lee, Minkyu Kim

Mine tailings storage facilities (TSFs) can be a significant source of fine, respirable dust. This dust poses concerns, especially for nearby communities, because of its detrimental impact on respiratory health. To address these concerns, this study examined the effectiveness of commercially available polymers, known for their biocompatible and environmentally friendly features, to prevent dust generation from upstream-type TSFs in active mining operations. It focused on two areas in TSFs: the tailings beach and slope/dike surfaces. Two types of polymers—polyethylene glycol and poloxamer—were selected, and their effectiveness was evaluated in a series of phased laboratory and field tests. The lab tests investigated the moisture-retention capacity of the tailings after treatment with the polymer solutions as well as the ability of these solutions to reduce dust emissions. Polymers were applied to a tailings bed surface in the lab and dust was generated from this surface using a wind tunnel. PM10 and PM2.5 concentrations were measured using laser-diffraction dust sensors, and the polymers were found to have reduced dust emissions up to 95%. Small-scale wind-blowing tests were conducted in the field (specifically, in a controlled environment at a TSF) to evaluate polymer effectiveness on the tailings beach and slope/dike areas. The tests revealed that the AP could efficiently suppress approximately 80% of PM10 and PM2.5 dust emissions at both types of areas. Finally, 1000 gallons of AP solution were discharged at the top of tailings beach and slope/dike areas, respectively, and found to be effective. The results of these tests showed the high potential of the biocompatible polymers to be a feasible solution for reducing the respirable dust emissions from upstream TSFs in arid and semi-arid regions.

By Kwangmin Kim, Junnhyeok Park, Taehee Lee, Minkyu Kim

Mine tailings storage facilities (TSFs) can be a significant source of fine, respirable dust. This dust poses concerns, especially for nearby communities, because of its detrimental impact on respiratory health. To address these concerns, this study examined the effectiveness of commercially available polymers, known for their biocompatible and environmentally friendly features, to prevent dust generation from upstream-type TSFs in active mining operations. It focused on two areas in TSFs: the tailings beach and slope/dike surfaces. Two types of polymers—polyethylene glycol and poloxamer—were selected, and their effectiveness was evaluated in a series of phased laboratory and field tests. The lab tests investigated the moisture-retention capacity of the tailings after treatment with the polymer solutions as well as the ability of these solutions to reduce dust emissions. Polymers were applied to a tailings bed surface in the lab and dust was generated from this surface using a wind tunnel. PM10 and PM2.5 concentrations were measured using laser-diffraction dust sensors, and the polymers were found to have reduced dust emissions up to 95%. Small-scale wind-blowing tests were conducted in the field (specifically, in a controlled environment at a TSF) to evaluate polymer effectiveness on the tailings beach and slope/dike areas. The tests revealed that the AP could efficiently suppress approximately 80% of PM10 and PM2.5 dust emissions at both types of areas. Finally, 1000 gallons of AP solution were discharged at the top of tailings beach and slope/dike areas, respectively, and found to be effective. The results of these tests showed the high potential of the biocompatible polymers to be a feasible solution for reducing the respirable dust emissions from upstream TSFs in arid and semi-arid regions.

By Jayant Khambekar

In a typical mining operation, run-of-mine (ROM) ore is crushed and screened to achieve a desired particle size distribution and then fed to processing equipment for further refining. For an operation to be profit-able, the ore handling system from the mine face to final product loadout must be reliable. However, the handling system components do not always perform as expected and production problems related to material flow occur. These problems include flow stoppages, limited live storage capacities, uncontrollable flow, segregation, spillage and dust emissions. These result in lost production, excessive maintenance, safety and environmental issues, and even structural failures, in some cases. Flow patterns Flow problems and their solutions can be best understood by first learning how bulk solids flow. As bulk solids discharge by gravity from a storage system, primarily two types of flow patterns can develop: funnel flow and mass flow. Figure 1 shows a schematic of these two flow patterns. In funnel flow, only a portion of the material is in motion during discharge, which flows toward the outlet through a channel that forms within the stagnant material. Funnel flow occurs when a hopper is not sufficiently steep and smooth to ensure flow along the walls or when the outlet is not fully effective. In mass flow, all of the material is in motion whenever any is discharged ? there is no stagnant material. Mass flow occurs when the hopper is sufficiently steep and smooth to ensure flow along the hopper walls. Shallow valleys are not permitted and the outlet must be fully effective. A third type of flow pattern, called expanded flow, can develop when a mass flow hopper (or hoppers) is placed beneath a funnel flow hopper or bin. The mass flow hopper is designed to activate a sufficiently large flow channel in the funnel flow hopper to avoid flow problems due to a rathole. The flow pattern in which a bulk solid discharges from a storage system strongly influences the flow problems that may occur in that facility.

Jan 1, 2009

By K. Saikiran, A. R. Nalla

Longwall management, regular shield maintenance, and evaluation of ground control problems can be performed using real-time shield monitoring program. Based on real-time shield pressure data, evaluation of intensity and interval of periodic weighting, estimation of time-dependent pressure increase and the effects of geologic anomalies can be obtained. In this study, full-face shield pressure data of over 457 m (1,500 feet) of face advancement is analyzed to evaluate shield response in the presence of surface lineaments, floor undulations, and multiple main roofs. Shield pressure increase due to web cutting is also correlated with setting pressure during periodic weighting and normal time. In addition, time-dependent pressure increase rate on Sundays and holidays is also correlated with time average pressure and the location of previous periodic weighting.

Jan 1, 2000

Colloidal interactions play a critical role in mineral processing, including grinding, physical separation (particularly flotation), dewatering, and tailings management. Despite great energy input in comminution to liberate valuables from gangues, heterocoagulation between valuables and gangues would prevent the separation of valuables from gangues. On the other hand, selective coagulation/flocculation to increase the size of desired fine particles could enhance physical separation and dewatering, while dispersion is needed for fine grinding. To control the state of colloidal dispersions by creating favorable conditions, it is of paramount importance to study colloidal interactions in a relevant system and understand underlying mechanisms. This review summarizes recent advances in developing the-state-of-the-art techniques and novel methods of measuring colloidal forces, including atomic force microscope, surface force apparatus, zeta potential distribution measurement, quartz crystal microbalance with dissipation, and our recently developed integrated dynamic force apparatus. The basic principle of each technique was introduced first, followed by a summary of critical information derived for the relevant mineral processing systems. Finally, the pros and cons of each technique were discussed to emphasize the use of complementary techniques that assist in solving fundamental problems in mineral processing.

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

The reduction process of pre-oxidized ilmenite concentrate powder in 30%CO–70%N2 atmosphere was characterized by thermogravimetric and differential thermogravimetric (TG-DTG) analysis system at the temperature from 1073 to1223 K. The isothermal reduction results show that the reduction process is divided into three stages and the corresponding apparent activation energies are obtained by iso-conversional method and model-fitting method, respectively. For the first stage, the conversion degree increases sharply with increasing time, and the reduction process is controlled by the random nucleation and subsequent growth model (A2 model). For the second stage, the conversion degree increases slowly with increasing time, and the reduction process is controlled by the diffusion of carbon monoxide in the reduced layer (D1 model). For the third stage, the reduction processes at different temperatures are controlled by the diffusion of carbon monoxide in the reduced layer (1073 K and D1 model), phase boundary chemical reaction (1123 K and R2 model), random nucleation and subsequent growth (1173 to 1223 K, A2, and A3 models), respectively. For the whole reduction process, the apparent activation energies obtained by iso-conversional method and model-fitting method are 71.72 and 31.92 kJ mol−1 , respectively

By Mingyang Li, Yan Lv, Xiaolong Ma, Xudong Gao, Jie Zhao, Yingyi Zhang

The reduction process of pre-oxidized ilmenite concentrate powder in 30%CO–70%N2 atmosphere was characterized by thermogravimetric and differential thermogravimetric (TG-DTG) analysis system at the temperature from 1073 to1223 K. The isothermal reduction results show that the reduction process is divided into three stages and the corresponding apparent activation energies are obtained by iso-conversional method and model-fitting method, respectively. For the first stage, the conversion degree increases sharply with increasing time, and the reduction process is controlled by the random nucleation and subsequent growth model (A2 model). For the second stage, the conversion degree increases slowly with increasing time, and the reduction process is controlled by the diffusion of carbon monoxide in the reduced layer (D1 model). For the third stage, the reduction processes at different temperatures are controlled by the diffusion of carbon monoxide in the reduced layer (1073 K and D1 model), phase boundary chemical reaction (1123 K and R2 model), random nucleation and subsequent growth (1173 to 1223 K, A2, and A3 models), respectively. For the whole reduction process, the apparent activation energies obtained by iso-conversional method and model-fitting method are 71.72 and 31.92 kJ mol−1 , respectively

By Hasan Nizamoğlu, Z. Abidin Sarı, Aslıhan Demiraslan, M. Deniz Turan, Tolga Depci

In this study, recovery of copper from solid material (obtained by leaching of chalcopyrite with oxalic acid in the presence of hydrogen peroxide) with a copper oxalate structure was carried out selectively using HCl. The chemical composition of the solid was as 29.3%, 9.7%, and 13.3% for Cu, Fe, and S, respectively. Selective recovery of copper by degrading the copper oxalate structure with a low-solubility product (Ksp = 4.43 × 10−10) was performed by conventional leaching in the presence of HCl. The optimum leaching conditions were determined as 5 M of HCl concentration, 318 K of leaching temperature, 120 min of leaching time, 25 ml/g of liquid–solid ratio and 400 rpm of stirring speed. Under these conditions, approximately 77% of copper and 3% of iron were taken into the solution. According to the characterization of the leach residue that was obtained, the oxalate structure was degraded. Moreover, the results of XRD analysis showed that the sulfur (S) and cubanite (CuFe2S3) phases were mostly observed in leaching residues, and this was supported by the SEM-EDX data. Based on the results, it may be stated that selective copper extraction can be obtained from a chalcopyrite concentrate by a two-step leaching method using a conventional hydrometallurgical technique.