Search Documents

By T. H. Eyde

Worldwide production of natural zeolites during 2001 was estimated to be about 3.5 Mt (3.85million st). Construction and agriculture continued to be the major consumers. Estimated production in North America during 2001, including the United States, Canada and Mexico, was about 40 kt (44,000 st). In the United States and Canada, the zeolitic tuffs are ground, extruded or modified for use as adsorbents, desiccants, ion-exchange media and carriers. In Mexico and the rest of the world, the zeolitic tuffs are cut into dimension stone that is used in construction. Zeolitic tuffs are usually composed of the minerals clinoptilolite, mordenite or both. They occur in a variety of colors and are easy to cut and shape. And they have low thermal conductivity. This construction application is classified with dimension stone rather than with chemical and agricultural uses.

Jan 1, 2002

By R. W. Smith, D. L. Taylor, K. A. Altman

The importance of metallurgical information in reaching appropriate decisions during the development of mining projects is demonstrated. A financial analysis is calculated using a simulation that includes random number generators. The results are compared to the results of a traditional sensitivity analysis. The traditional analysis is shown to have the potential to overestimate the value of mining projects. The type of statistical distribution selected for the random number generator affects the results significantly. The statistical method of analysis provides insight into the amount of metallurgical testing to be completed and verification of how representative the samples are.

Jan 1, 2000

By E. Z. Casassa

There has been a recent revival of interest in concentrated coal/water slurries as a substi¬tute for fuel oil or for coal/oil mixtures, particularly in electric power generation. The idea is not a new one. Coal/water slurries were transported by pipeline in the U.S. in the early nineteen-sixties, and the Black Mesa coal pipeline has been in operation for several years, while in Germany, coal/water slurries were being burnt for power generation in the early nineteen-seventies, as described by Merten and Höner (1972). Since coal is not a pure substance but a carbonaceous mixture, the different chemical and physical behavior of coal/water dispersions from different deposits must be understood in order to optimize the properties of the result¬ing slurry fuels. Since minerals which are minor constituents of coal may also strongly affect slurry properties, coal chemistry may vary considerably even within a single deposit. Thus it is unlikely that there will be a single formula for optimizing the slurry properties of all coals, and even the answer for coal from a single source may change with time.

Jan 1, 1983

By L. Lacerda, C. Rose, E. Zellers

Approximately six hundred air sample measurements were taken at several U.S. underground metal/nonmetal mines in 1998 and 1999. This air sampling effort was organized by the Nevada Mining Association to evaluate mining conditions and to evaluate the Mine Safety and Health Administration’s (MSHA) Proposed Rule on Diesel Particulate Matter Exposure of Underground Metal and Non-metal Miners. MSHA’s proposed air sampling method, NIOSH Method 5040, was tested under controlled conditions and under normal mining conditions. Unfortunately, NvMA sampling results have indicated that carbonaceous rock dust, oil mists and even cigarette smoking create severe sampling interference problems for NIOSH 5040.The main conclusion was that NIOSH 5040 did not distinguish between DPM and other airborne carbon particulate. Thus, it is not a reliable method of accurately and unequivocally measuring DPM in underground metal/nonmetal mines.

Jan 1, 2000

By M. J. Ramos

Without an exclusive definition of administration in business, we could propose to define it as performance by management to adopt or implement established business formulas. Administration could also be defined as a universal process that organizes people, and achieves, through efficiency, common objectives and goals. Humanity developed some form of this process from the beginning of civilization. To imply that something is new in administration might be considered specious or naïve. Moreover, what is new in management? Administration of business is not new to the world. To prove this statement, we need only ask this question: Does the architecture and monumental workmanship of the past civilizations of ancient Egypt, Rome, and the Incas demonstrate management without administration and without definition of objectives? The answer must be a resounding ?NO!? In spite of this acknowledgment and for the purposes of this presentation, I will use the word ?new? in business and hope that the reader will follow my reasoning. The mining industry has unique characteristics in respect to other industries. It is multi-disciplinary, has a single purpose (majority for one metal), has two players (man and nature), and it involves high risks for generating environmental imbalance. Mining exploits non-renewable and finite resources, creates an unstable job market (work hard to have no work) and a speculative economic market with unpredictable prices ? a one-time payment for a finite resource with multiple recycling. On top of all that, the industry still operates within obsolete petroleum-based technology, utilizing practices that were designed two centuries ago. Today, we confront the challenges of the millennium with outmoded practices and management. Ordinarily, several styles of administration are standardized into a FRAGMENTED vertical system of organization. Mining has rigid objectives in production, with profitability as the focus from the beginning to the end. Citing the concept of safety, as an important facet of production is bombastic since, in truth, mining is an experimental industry that consistently reports high numbers of fatal accidents. In mining, we designed a process to work according to our objectives, demanding attention and supervision of all levels of management with a halo of parameters that are not assimilated into the design. We continue to perform a rigid style of management in an industry that is still not responsive to variations of the market ? losses in particular. The existing design process generates loss without capitalization and without response to said loss. This perception is reflected in a mindset that is only too ready to ignore mining liabilities. The reality of the enterprise has created an immense pressure from top to bottom in the hierarchy to do more with less. It is for all of these reasons that I propose to set forth a new essence for administration that encompasses an alternative vision and style in mining: Management by Loss. MANAGEMENT BY LOSS Management by Loss (MBL) is a systematic, integral process organized to quality control operation and the human profitability within the industry. It permits focus on achievable goals by utilizing the best practices (Mining Open-closing). Identification and characterization of loss in the process determine how objectives are defined, controlling the time limits to execute based on constant balance of mass, energy, water, and ?wastes? in each stage of the industry, in order to reach final objectives. The concept of loss can be defined by various criteria. Generally, it is the mass that could not make or arrive at its destination from a designed process or simply, it could not maintain balance. Otherwise, the design of the process describes the final point of the resource. However, those resources could not make their destination because of failure to use the best design, resources and TIME. The loss has typical characteristics such as Identifiable, classifiable, measurable, manageable, controllable, valuables, negotiable, avoidable, reportable, and monitoring. In the traditional scheme, these losses are not registered; they are made exclusions. We are trapped within a system, which was designed to obtain objectives of the industry in a specific timeframe. In the present style of administration, the focus is total - our emphasis in this treatise is in the loss. The current traditional report form contains only the most positive achievement of objectives, only the best of the exercise, humanizing numbers, without touching what we left behind or what we were waiting for to assimilate as a ?surprise account?(new account of liabilities). Management by loss is a method that redefines the concept of waste (waste zero) for controlling the mine operation under the equilibrium of the ecosystems. This method confronts the problems that impact our industry in this millennium. Understanding and quantifying losses (reserves, resources, time, energy, water, soil, materials, equipment, tasks, labor, ecosystems, etc) is a priority mandate for the industry and demands the application of a ?new ? style of administration by seeking to maintain balance instead of the disequilibrium that mining now creates in nature. It is necessary to answer questions such as: How can we minimize loss? How can the loss be assimilated during the life of the mine? What is the vision of mining in respect to the generation of waste? How can we convert liabilities into assets? In addition, the control of loss is determined in the achievement of the plan. Loss occurs because of a failure of the process in the original plan. Still we do not plan to fail but we fail to plan appropriately. It is a remarkable thing to accomplish and compel those objectives described in the original plan when that plan is designed with a determined budget. If not, we lose time and, of course, capital. Moreover, in Management by Loss (MBL), we can find answers to the following questions: What is the multiplier of productivity in mining? What are the influences of identification and characterization of loss and what is the level of efficiency of energy in order to achieve waste zero (effective cut off grade)? The challenges of mining in this millennium validate this new style of administration. Finally, it is important to point out that mining is entering into an era that has different rules, but the industry is still run by companies functioning with objectives from two centuries ago. They are trying to confront issues with concepts that are not designed for new tasks. Therefore, I ask you to consider this new style of administration of business under a vision of how the industry should be organized and managed, with an attitude of balance toward nature and social responsibility.

Jan 1, 2009

By W. L. Hollinshead, Alwin Poltinger

GENERAL Tunneling by hand digging is as old as the history of humans. Mechanized tunneling did not begin to replace manual methods until around the beginning of the 19th century(Brunel patent, 1818). It brought with it a higher degree of safety for the workers and a much higher rate of boring. But for any kind of tunneling, an accurate and feasible method of survey must be accomplished during mining. That means, that for each tunnel project the most efficient survey method must be devised. The method to be defined depends on the spatial curve, diameter, speed of tunneling method, purpose of tunnel and contractual accuracy. The final accuracy of a finished tunnel is heavily dependent upon three critical elements: 1. Quality of the above ground survey 2. Tunnel traverse and directional transfer from above ground 3. Guidance for the mining job. Combining The Survey And The Guidance System Since the guidance system (GS) is one of the critical factors in the determination of the tunnel final accuracy, it is necessary to analyze how the directional control and tunnel traverse measurements can be effectively integrated into a GS. Any guidance system, whether manual or high technology, must continually detect and compensate for movement of its theodoliteor laser station standpoint. Movement beyond a preset allowable amount must generate a warning or error message to the user. Additionally, optical refraction can interfere with the results. Refraction will have an effect on any kind of optical GS. Therefore, careful selection of target and standpoint locations can minimize, but not completely eliminate, the influence of refraction. Some GS technologies, such as Gyro-based systems, are immune to the effects of refraction, but have other, methodical errors which will be described later in this paper. GUIDANCE Overview Why is a guidance system necessary? A GS, whether manual or automatic, compares the design direction and slope of a tunnel with the current position of the mining

Jan 1, 1997

By Allen W. Hatheway, John A. Albritton, Lloyd B. Underwood

Missouri River Division (FORD), U.S. Army Corps of Engineers (COE), has completed (October 1982) a study for the U.S. Air Force Ballistic Missile Office, in which desireable and needed changes in contracting methods for underground construction were identified. Due to the importance of geotechnical considerations in such construction, a good number of the resulting recommendations relate to geotechnical considerations. Corps contracts have traditionally served as models for contract documentation by public agencies and in private enterprise. Several standard features of present-day contracting methods were Corps innovations. Corps officials are generally in agreement with the recommendations of the Better Contracting reports published by the U.S. National Research Council (NAS/NRC), through its U.S. National Committee on Tunneling Technology (USNCTT). However, the findings of the 1982 MRD study indicate that additional changes are warranted for underground construction contracting methods; changes that deal specifically with site geological conditions, both known and to be reasonably anticipated, as well as with their associated impacts on construction. The 1982 MRD report identifies the need for nine specific improvements in geotechnical aspects of contracting; improvements based on recognition of geological conditions.

Jan 1, 1983

In the last four years, 2007~2010, 9 out of 24 metal/nonmetal underground mine fatalities were caused by ground fall across United States of America (Mine Safety & Health Administration, MSHA). To reduce or eliminate incidents/accidents caused by ground fall, this paper clarified how to design and select ground support based on different ground conditions, how to use mine ground support standards, what geotechnical engineers and underground operators should do to keep mine production free of ground failures.

Jan 1, 2012

By E. Piesch, M. Urban, G. M. Hassib

INTRODUCTION In radon dosimetry diffusion chambers with passive [a]-detectors are now in current use to investigate the long-term accumulated indoor exposure of radon and daughters. For the diffusion chamber developed at Karlsruhe the electrochemical etching technique (ECE) was applied to reveal [a]-particles in polycarbonate plastic detectors. Compared to conventional etching, the main advantages of the ECE are the large track diameter, simple track counting in a single field of about 1 cm2, stability of the latent tracks to humidity and temperature and ability for a long-term accumulation up to 1 year. The electrochemical etching system was designed to etch in one run about 101 foils by using a 200 W high voltage generator. The commercial available radon dosimeter system is applied for a country wide program of measuring radon in dwellings. Because of an increasing interest of radon monitoring in mines, environmental monitoring and personnel dosimetry the properties of several track etch detectors have been studied. In the comparative study, Makrofol E, LR 115 and CR 39 were used in the diffusion chamber to investigate the etching techniques, the relative efficiency, the measurable [a]-energy range, and the counting statistic for the measurement of radon concentration. THE KARLSRUHE DIFFUSION CHAMBER The design of the Karlsruhe diffusion chamber is presented in Fig. 1. The upper part of the chamber is closed by a fibreglass filter to separate radon from aerosols, heavy dust particles and radon decay products. Inside the diffusion chamber [a]-particles from radon and daughters are detected by two passive radon detectors, one on the bottom of the chamber and the other in front of the filter. With the fibreglass filter applied the diffusion time is about 1 minute for radon. Therefore, also short-term variations in the radon concentration are recorded by the track detector. Mainly because of the short halflife of thoron (56 s) only about 7 % of the thoron concentration is expected in the diffusion chamber. Radon monitoring provides the estimation of the long-term accumulated mean value of the radon concentration with a lowest detectable concentration of 0.1 pCi/1 after 3 months accumulation by using polycarbonate track etch detectors, an electrochemical etching technique and track counting in a single field of 1 cm2. The diffusion chamber was optimized for the polycarbonate track detector with respect to chamber geometry and detector position [1]. Table 1 presents data for 3 different diffusion chamber designs. The radon sensitivity of the diffusion chamber depends on the [a]-energy discrimination and the angular response of the [a]-track detector. The difference between foil No 2 and foil No 1 can be explained by an additional plate-out effect of radon daughters on foil No 3. The high sensitivity of foil No 3 compared to that of foil No 2 is caused by an increase of the effective volume and the effective area for [a]-particle from radon and from plated-out decay products, respectively. Additional experiments have been performed in order to investigate the electrostatic properties of the plastic material and the properties of the diffusion filter [1]. The properties of bare a-detectors were compared with those inside the diffusion chamber. In contrast to laboratory results, dust particles deposited on the detector surface or in the environment of the detector obviously affect the reproducibility of the bare detector significantly. After 4 months exposure in dwellings the scatter of 10 dosimeters exposed in the same room exceeds a factor of 3 compared to 15 % for the diffusion chamber. COMPARATIVE STUDY OF TRACK ETCH DETECTORS Detector types and evaluation technique In the comparative study the properties of the following plastic track etch detectors have been applied: - LR 115 from Kodak Pathé, France, is a red dyed cellulose nitrate layer of 13 µm thickness on a 100 µm thick polyester support. The holes appears as bright spots in a dark red background. In an optical microscope counting of through etched [a]-tracks which must penetrate the detector layer - CR 39 from Pershore, England, is an ally1 diglycol carbonate plastic of about 300 m thickness. The normal etched [a]-tracks are counted by an optical microscope and the ECE [a]-tracks by a microfiche reader.

Jan 1, 1981

By S. K. Singh, J. Shepherd

"Feather edging"- a major source of injury and fatal accidents in Australia, South Africa and USA, refers to a phenomenon where the roof, at the goaf edge, falls as a thin wafer of rock often suddenly, over-riding conventional timber breakerlines. It may run down and affect adversely a working bord at distances of 15 metres or more from the goaf edge. Feather edging typically occurs in relatively massive, strong roof strata such as sandstone or conglomerate. This paper presents the results of a mine trial where a concentrated row of fully grouted bolts were able to resist the feather edging in the first comprehensive, monitored trial in an Australian pillar ('total') extraction coal mine.

Jan 1, 1999

By Leonard Sugin

Recent changes in the field of ore and bulk commodity handling has forced a reevaluation of previously conceived notions. When vessels were small, and sources of raw material were reasonably close to areas of need, the role of the shipping terminal was of secondary importance. Now terminals must be built to take advantage of the economic benefits of the supercarriers. The shipping rates of the 80's will not be determined by the 60,000 DWT or even 150,000 ton capacity bulk carrier, but rather by the supercarriers in the 250,000 DWT class or larger. When the Suez Canal was closed, the shipping industry took a hard look at the economics of the large bulk carrier. Naval architects overcame the problems and successfully designed large supertankers, which today are plying the seas in excess of 350,000 DWT. Orders have been placed for tankers of 480,000 DWT. The shippers of dry bulk materials are now coming to similar conclusions about the economics of supercarriers. As of today, over 40 orders have been placed for vessels in the 250,000 DWT class, representing an investment of over 11/2 billion dollars, and many more are being considered. These vessels are being designed as combination ore/oil (0/0) or ore/bulk/oil (OBO's) carriers. The oil industry has seen the need for terminals which can accommodate these supertankers. The dry bulk shippers, and particularly ore shippers, must now act.

Jan 1, 1972

By C. J. Hall

I would like to congratulate Professor Gershon on an idea that is obviously valuable and is certainly new to me. It has, however, to be further developed, in that one can get fallacious results by limiting oneself to positional weights. In the example problem, the positional weight of one block was 8.6 (the 8.0 value in the paper was incorrect) for 36 units in the cone, for a mean block value of 0.239. The positional weight of the second block was 4.4 for 15 units, for a mean block value of 0.293. Surely one would expect the second block to be rated higher. Additionally, the time value of money adjustment cannot be determined by depth, because the time that a block is mined is determined by the mining sequence, not depth. Figure 1 shows a slightly altered version of Professor Gershon's pit. The overall value of the pit is the same, as are the total values under each of his blocks. The values in the right-hand cone have been reversed top to bottom, and the values in the rest of the pit adjusted to keep the central cone total unchanged. All values have been multiplied by 10. Figure 2 shows the sequence of mining, at three blocks per year, for Professor Gershon's pit, and Fig. 3, the sequence for a pit under the other block. Table 1 shows the value and discounted value (15%) of Professor Gershon's pit, and Table 2 shows similar values for the second pit. It is apparent that the second pit schedule is more valuable than the first.

Jan 1, 1988

Current design guidelines for the surface catalysed oxidation of Fe(II) on Fe(OH)3 (Ochre) in passive mine water treatment systems are based largely on empirical data as the details of rates and mechanisms have not fully been revealed. Also the effects of elevated carbonate concentrations, typical of many UK minewaters, on the surface catalysed oxidation rate are unclear. In order to move away from empirical design and towards sound engineering that is based on geochemical and hydrological understanding it is necessary to quantify these reaction rates. In this study the effects of Fe(OH)3 and carbonate on the rate of Fe(II) oxidation by dissolved oxygen have been investigated with an aim to delineate the reaction mechanism. Experiments were conducted under well-controlled conditions. Preliminary results indicate that the surface catalysed reaction is an order of magnitude faster at pH ~6.4 with 200 mg/l Fe(OH)3 than the homogeneous rate and is dominated by an elevated rate of removal and oxidation of Fe(II) from the solution phase. It is also apparent that the oxidation rate of actual adsorbed Fe(II) is substantially retarded with respect to the homogeneous rate. Carbonates were not shown to affect the surface rate within the bounds of this preliminary study.

Jan 1, 2006

By Tyler Lahti, Peter Borgacci, Mary Jane Ferraro, Prakash Nadesparan

Toronto Tunnel Partners (TTP), under contract to Metrolinx/IO, is constructing new twin rail tunnels under the Highway 401 & 409 interchange to accommodate additional tracks to support the GO Expansion program for future two-way, all-day service. The new tunnels are being constructed using the Sequential Excavation Method (SEM) and utilize a tunnel pre-support system consisting of a series of 800 mm diameter steel pipes to form a pipe canopy. The pre-support pipes were installed with an Auger Boring Machine (ABM) in four separate headings; one heading from each of the tunnel end portals, and two from a shaft in the middle of the highway. To facilitate the auger boring operation, a custom steel reaction frame was required to counteract the thrust from the ABM at the portals, and a temporary shaft structure was installed in a narrow median space of the highway. The installation of the pipe canopy had to overcome challenges including removal of obstructions, alignment issues, and controlling settlements to the highway surface. This paper discusses the purpose of the pipe canopy, design and installation of the temporary shaft and structures to support the auger boring operation, the experience of the contractor during the installation of the pipes, and brief overview of the experience tunneling below the pipes.

Jun 13, 2021

By R. M. Corn

The Non-Time Critical Forest service CERCLA Action at Mansfield Canyon, Santa Cruz County, Arizona designated previous locators of unpatented mining claims as owners/operators of the Hazardous Waste Facility, retroactively liable for all reclamation costs including reclamation of mines acquired by the Forest Service. The CERCLA Action is based on non-existent tailings, a non-existent permanent resident, inaccurate and unreliable data and did not review or consider prior USGS and USBM data. The consequences of the Forest Service action include(1) reduced exploration, (2) loss of credibility, (3)public disillusionment and distrust.

Jan 1, 2000

By Graham Davis

The future of the world's minerals industries is often painted as bleak. Peter Drucker has repeatedly proposed that the demand for minerals has become "uncoupled" from world economic growth.' This implies that, while mineral demand was in the past linked to the growing demand for and consumption of goods and services, further world development will not require substantial mineral inputs. Lester Thurow noted that for these reasons the US minerals industry is diminishing in scale and economic importance.2 There is some documented evidence of such uncoupling, and the demand for minerals may indeed diminish in the future. But such announcements are, to this point, no more than speculation. For instance, is it not just as likely that renewed environmental concerns will cause increased demand for the relatively innocuous environmental properties of metals, replacing plastics? And even if the prophesied demand decreases do occur, a sufficient fall in metal prices due to technological advances could increase the quantity of minerals demanded above current levels, in spite of leftward shifting demand curves. Thus, worldwide mineral production activity may increase or decrease in the future and no one can say whether more or fewer of the earth's citizens will become involved in the extraction and processing of minerals.

Jan 1, 1994

By M. Younis, E. Comis

"The success of a tunnel project relies on many factors, but one of the most important is also the most overlooked: coordination by all parties involved during the design stages. This is particularly true of segment design and TBM design. Tunnel lining with segmental rings is usually designed according to the standards of reinforced concrete construction based on a given GBR. However, for TBM tunneling, the determination of loads during ring erection, advance of the TBM, earth pressure, and bedding of the articulated ring are all part of the tunnel lining design as well. TBM design can be heavily affected by the segment arrangement, dimension, and weight, but these are usually given as a fixed input to the TBM manufacturer—a process that can cause unnecessary complications. The authors propose that the industry evaluate the process as it stands. In order to find the optimum balance between lining design and TBM cost and operational workflow, both designs should be finalized concurrently. This requires coordination between the TBM manufacturer and segment designer from the early stages. The aim of this paper is to evaluate the influence of the segment lining design on TBM cost and performance, and to provide commentary on existing design guidelines to optimize lining and TBM procurement. INTRODUCTION The conventional project setup for tunnel lining design and the design and manufacture of the tunnel boring machine (TBM) should be coordinated in a timelier manner. It is widely acknowledged that the design of segments must consider the forces exerted by TBM rams during tunnel construction, but other inputs are most frequently provided to the TBM manufacturer as fixed parameters to design around. This paper describes other important factors in TBM design that impact not only the interaction with the segments, but also the construction of the tunnel in terms of overall production and even safety. For example, the segment width and tapering have direct influence on shield body length and thrust cylinder size. Furthermore, TBM geometry can also affect the backup (trailing gear) layout and length."

Jan 1, 2016

By D. Scott Scovira, Thomas Gustavsson

Exiting WW2, the potential of nitrates and hydrogen peroxide for application as industrial explosives both became known. The technology stream advanced the development and uptake of nitrate-based explosives to the point that they are the current global standard for blasting. Recently environmental issues are influencing the strategic agenda of extractive industries. The mid-2010s saw renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the 2020s provided additional impetus to investigate hydrogen peroxide-based explosives. Hypex Bio is at the forefront of developing and delivering bulk gas sensitized Hydrogen Peroxide Emulsion (HPE) for blasting. HPE consists of hydrogen peroxide along with smaller amounts of fuel and emulsifier. The consistency of HPE is similar to industry- standard nitrate-based emulsions. It is compatible with existing priming and initiation systems. HPE does not contain nitrates and thereby does not produce post blast nitrous oxide fumes nor discharge of nitrates or ammonia to mine water. Importantly, HPE contributes to reduction in total carbon emissions as compared to nitrate-based explosives.

Feb 1, 2025

By John Reilly

The author?s paper at RETC 2007, ?Alternative Contracting Methods? addressed strengths and weaknesses of DBB+DB and introduced Construction Manager/General Contractor (Portland model) and Alliancing (Australian model). Considerable interest in these was expressed by several public agencies at that Conference and at the presentation. The author is assisting the Washington State Department of Transportation (WSDOT) and the Toronto Waterfront Revitalization Corporation (TWRC) with possible implementation of Alliancing. WSDOT is evaluating ways to do this and is considering a delivery methodology, under existing Legislation, based on the CMGC Portland model with incentives and disincentives, moving towards Alliancing. This paper will build on the 2007 paper and update implementation considerations.

Jan 1, 2008

Fluorspar was not mined in the United States during 2004, although a small amount of usable synthetic fluorspar (CaF2) was produced from industrial waste streams. The majority of fluorspar consumed in the United States came from imports or stockpiled material purchased from the National Defense Stockpile (NDS). In addition, consumption is supplemented by use of by-product fluorosilicic acid produced at phosphoric acid plants. In 2004, annual production of fluorosilicic acid was 50kt (55,000 st) or about 88 kt (97,000 st) of 92 percent fluorspar equivalent. In 2004, annual production of fluorosilicic acid was 50kt (55,000 st) or about 88 kt (97,000 st) of 92 percent fluorspar equivalent.

Jan 1, 2005