Search Documents

By S. A. Shoop, J. J. K. Daemen

Site-specific blast vibration prediction can be more accurate than using a universal prediction equation. Vibrations from 37 blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly, inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations predicted from US Bureau of Mines (USBM) equations. Vibration restrictions based on USBM studies could then be too conservative or too lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases, energy was concentrated at frequencies corresponding to delay intervals.

Jan 3, 1985

By S. J. Boone, A. Poschmann, C. Pound, A. Pace

San Diego’s Stadium Conglomerate consists of poorly cemented cobbles, gravel, sand, silt and clay. Conventional laboratory and in-situ testing is not suitable for characterizing its engineering properties. Although the formation is often considered a “rock” its behavior is more readily modeled using soil mechanics. Static and seismic design of a tunnel for the Mission Valley East light rail extension required that the stress-strain characteristics of the ground be identified over a broad strain range. Geophysical methods and field plate load testing were used to develop a full non-linear stress-strain model of the expected ground behavior. Quantification of the coarse material distribution was also required for selection of tunneling methods and construction considerations.

Jan 1, 2001

Researchers from the National Institute for Occupational Safety and Health (NIOSH) are developing a coal pillar rib rating (CPRR) technique to measure the integrity of coal ribs. The CPRR characterizes the rib composition and evaluates its impact on the inherent stability of the coal ribs. The CPRR utilizes four parameters: rib homogeneity, bedding condition, face cleat orientation with respect to entry direction, and rib height. All these parameters are measurable in the field. A rib data collecting procedure and a simple sheet to calculate the CPRR were developed.

Jan 7, 2020

By F. Grajales Muñoz

The Ciénega project, now under construction by Peñoles group, is located in the mountains of northwest Durango, Mexico. The gold and silver deposits are found in a 4-km (2.5mile) long system of veins. An underground operation will be built. The planned 1 kt/ d (1100 stpd) process plant will contain a countercurrent cyanide circuit for oxide ore and a flotation circuit for sulfide ore. Considerable resources have been devoted to the development of infrastructure in the isolated location, as well as for the mitigation of environmental impacts. Startup is scheduled for the third quarter of 1994. Ciénega’s ore bodies consist of quartz veins containing gold, silver, lead and zinc values. The vein thicknesses vary from 2 to 10 m (6.5 to 33 ft) with a northwest trend and nearby vertical dip. Veins are hosted in Tertiary volcanic rocks. The district has intermittently been explored since 1971 by Penoles. After the third series of diamond drilling and direct development work on vein, Peñoles decided to begin project construction.

Jan 1, 1994

By C. Sun

The Leeville underground mine has been in operation since 2006 and currently produces 3,500 tons of ore per day with an average gold grade of 0.34 opt. The mine has a large horizontal extent of 2,500 feet by 500 feet and a vertical extent of 20 to 200 feet. Based on the characteristics of the ore bodies, a long-hole stope and cut-and-fill mining methods are used at the deposits which are divided into several mining zones. Cemented rock fill (CRF) is used as the backfill in the open stope. CRF design includes the aggregate design, the ratio of cement and fly ash design, and strengths for the long-hole stope and cut-and-fill. In the aggregate design, the particle size distribution is one of the most influential aggregate characteristics in determining how it will perform as a basic backfill material. Gradation helps determine durability, porosity, cement and water requirements, strength, and shrinkage. To cut the backfill cost, fly ash usually is added into the binder to replace some part of cement. However, adding fly ash can affect the strength of the backfill. The reasonable percentage of fly ash is also important for making a good and low cost backfill. Based on the different mining method, the different backfill with different strength is designed. A systematic quality control procedure for aggregate and backfill is followed. After four yeas application, CRF system in Leeville achieved very good results.

Jan 1, 2011

By S. Roy

Soft laminated iron ore (SLO) having a higher hematite content and Martite goethite iron ore (MGO) having a higher goethite content were subjected to detailed characterization and beneficiation. The present research was designed to investigate if these abundant, low-grade ores can be enriched adequately using standard industry techniques. No significant enrichment of the ores using jigging operation on the coarse (-3,200 +595 mm) size fraction could be achieved. Good liberation was only attained in the 150 to 300 mm particle size range in both cases. Desliming enriches the ground ores significantly. The effect of the feed size on the separation efficiencies of the ground ores were studied using flowing-film concentration on a Wilfley table. Better enrichment is obtained in the case of 150-mm sized feed by tabling. The grade of SLO is improved from 56.14% to 66.51% Fe, while the Fe content of MGO is enriched from 55.16% to 65.83%. Substantial rejection of alumina and silica is also achieved. Due to the friable nature of MGO and the higher goethite content in it, the loss of Fe in the form of ultrafines is greater in this case compared to that of SLO.

Jan 1, 2009

By S. Bargigli, S. Ulgiati, M. Raugei, F. Cherubini

Metallic magnesium is mostly used in lightweight alloys in order to decrease fuel consumption in automotive applications. Several different production processes are currently used worldwide, and the magnesium production scenario is changing rapidly, with Chinese production increasingly dominating the world market. For the purpose of this paper, a novel approach to Life Cycle Assessment was applied, in which Material Flow Accounting and energy-based methods (Embodied Energy, Exergy and Emergy Analyses) are integrated and complemented, with a detailed description of the environmental hazards associated with emissions from all the different processes.

Jan 1, 2005

By Michael J. Lehnen

Slurry diaphragm walls are commonly used as both temporary excavation support walls, and permanent structural walls, for circular shafts and long rectangular structures (such as underground subway stations); however, they are not commonly used for more compact rectangular or square shafts. In these instances, a second wall is typically cast inside the slurry walls to form the permanent structure. This paper discusses the approach used on the Silicon Valley Rapid Transit Project in California to analyze these compact rectangular types of structures for static and seismic loading, and to determine whether or not slurry walls can be confidently used as both the temporary and permanent walls for two tunnel ventilation shafts.

Filtration systems with disposable filter elements (DFEs) are used in the underground coal mining industry to control particulate matter emissions from diesel-powered permissible and nonpermissible coal mining equipment. This study was conducted in underground mine conditions to evaluate three types of high-temperature DFEs used in those filtration systems. The DFEs were evaluated for their effects on the concentrations and size distributions of diesel aerosols and concentrations of nitric oxide (NO) and nitrogen dioxide (NO2). Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. After an initial DFE degreening period, the filtration system with all three DFEs was found to be very effective at reducing total mass concentrations of aerosols in the mine air. The effectiveness of DFEs in filtering aerosol mass was found to be a function of the engine operating conditions. The efficiency of the new DFEs significantly increased with accumulation of operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on performance of the DFE elements. The effectiveness of DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for both DPFs and DFEs when the engine was operated at high-load modes than at low-load modes. Initial heating of certain DFEs resulted in visible white smoke and substantially elevated aerosol number concentrations. The effects of the DFEs on total nitrogen oxides (NOX) concentrations were found to be minor. The NO2 fraction was found to be generally lower for the DFEs than for the muffler. The engine-out NO2 fraction of the total NOX was found to be substantially higher for low-load modes than for high-load modes.

Jan 1, 2011

By Andy Davis

The evolution of pit lake water quality depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock vs. oxidizable sulfide content, the alkalinity of recharging groundwater and the evapoconcentrative characteristics of the system. This paper assesses the geochemistry of 11 existing pit lakes, ranging from the acid Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits, with long-term chemistry lying on a geochemical continuum between end members that consist of influent calcium bicarbonate groundwater and naturally occurring sulfate-rich evaporate playa lakes.

Jan 1, 1997

By W. J. Mahoney

A good quality assurance program at a coal mine or power plant is accurate, timely and consistent. The quality analysis is accurate due to a complete sampling of the coal stream loaded into the unit train. The sample analysis is accurate because standardized testing procedures are applied. Once an analysis is completed, the results must be communicated to the electric utility in a timely manner. The electric utility needs the results to better manage the coal inventory at its power plants. A quality assurance program can also help a mine deliver a consistent product to a utility's power plants. The importance of accuracy, timeliness and consistency are based on major changes that are taking place in the electric utility industry.

Jan 1, 1994

By F. W. DeVries, O. B. Mathre

Addition of Kastone® peroxygen compound and formaldehyde to cyanide gold extraction process effluents, containing at least 5 mg soluble copper per liter, will oxidize acid-dissociable cyanide to levels less than 0.2 mg per liter, without appreciable oxidation of thiocyanate. Most of the copper precipitates and is removed by filtration of the treated solutions. The treatment can be completed in less than 2 hours when the excess of hydrogen peroxide over the cyanide is about 75-100 mg per liter. The excess hydrogen peroxide destroys residual formaldehyde and then is catalytically decomposed by the copper-containing solids that separate, so it will not interfere with subsequent operation. A pilot plant using this technology has been operated for more than four months at rates from 1-2 gpm. Clear, filtered effluent containing less than 0.2 mg acid-dissociable cyanide per liter has been produced.

Jan 1, 1981

By P. Zhang

The use of phosphate depressants in the cationic flotation of silica from francolite in the Florida phosphate industry is rarely practiced. The occasional use of gelatinized starch derivatives and pH adjustments to assure a slightly alkaline flotation feed slurry pH have been used in some processing plants to improve selectivity. This paper presents a preliminary laboratory comparison of several potential phosphate depressants for use with the flotation of siliceous phosphates. It was found that starch is ideal for floating fine (-35 mesh) silica from phosphate, while sodium tripolyphosphate may be the best for coarser (+35 mesh) feeds.

Jan 1, 2009

By W. R. Dengler, R. S. Brown

In 1974, Brunswick Mining and Smelting Corporation Limited started a 48 million dollar expansion programme at their property in Bathurst, New Brunswick. A portion of the expansion plans includes a 26 foot diameter 4,525 foot deep shaft, underground crusher and conveyor excavations and lower level access development. J. S. Redpath Limited was awarded the contract for the new shaft and associated rock work in May 1974. Brunswick Mining and Smelting Corporation Limited, a member of the Noranda Group, operate this 10,000 ton per day lead, zinc, copper plant with proven reserves in excess of 90 million tons. While most of the ore is provided by the underground operation at the Number 12 ore body, some tonnage is produced from the open pit at the Number 6 ore body. Long range plans indicate a phasing out of the open pit and an increase in production from the underground operation. Existing facilities at the underground mine could not provide additional tonnage, thus the requirement for a new shaft. (Figure 1) The new shaft will also provide access to ore below the 2,800 level which is currently the bottom level of the existing facility. The contract called for sinking a 26 foot inside diameter, nine compartment concrete shaft 4,525 feet deep (Figure 2). Station access and ramp development from existing workings would be required to the bottom of the new shaft. In addition, development work for new crushing and conveying facilities was needed simultaneous with the shaft sinking.

Jan 1, 1976

By K. Y. Vasioutchkov, Y. F. Vasyuchkov, B. M. Vorobjev

In general a term "unconventional mining or "non-traditional mining technology" getting more and move familiar to the mining engineering media. There are several alternating terminological combinations such as "in situ mining", "borehole mining", "shaftless mining", "mineless mining", "geotechnology" etc.; specific terms denote particular method of unconventional mining technology: "underground coal gasification in situ", "underground coal combustion in situ", "borehole hydraulic coal mining" and others. Principal scheme of unconventional coal mining technology is shown in [Figure 1:] One of the greatest potential for coal utilisation during the beginning decades of on coming cetury is the synthetic fuel-gas derived from coal as a product of coal gasification. It is quite logical to enrich this gas before burning it with natural gas, that is methane, contained in coal measures. Thus it is reasonable to suggest a new concept of unconventional coal mining and utilization technology featuring integrated methane drainage with coal-gas combined cycle. Proposed unconventional technology of coal mining is characterized with: - opening up a coat deposit through boreholes, drilled from the surface and used for coalbed methane drainage as well as for coat gasification in situ; - aggregation of methane producing and coal gasification station on mining side with thermo power plant on the electric power generation side in one integrated industrial enterprise. The further improvement of the conventional coal mining technologies both surface and underground could give only insignificant results in economical, ecological and social aspects, but would not be able to provide basic requirements of the XXI-st century. Significant increase in economical efficiency, cardinal humanization of coal mining and basic improvements in environment protection would be achieved through introduction and implementation of innovative or unconventional coal mining technology. These considerations are applied on both coal production and coal utilization sides as far as coat based energy generation is concerned. Now a general opinion is widely spread that an application in the same manner of the traditional technologies of coal mining and electric power generation would inevitably cause further irreversible damage of the global eco-system, notwithstanding the certain environment protection measures being taken. Keeping the recent pace of the eco-system degradation the whole our civilization would be in danger. Thus the solution of this problem is to be found in developing, promoting and implementing in industry unconventional coal mining and modern advanced clean coal technologies. Coal reserves with favourable conditions at shallow depths are -being rapidly depleted in all countries with developed coal industry. So in nearest future more coat will be mined from deeper levels with higher operational expences and with lower labour productivity. For example in Russia only 20% of proven coal reserves can be specified in quality as easy mined reserves, i.e. coal reserves with a good minability. Unconventional (borehole in situ) coal mining enables us to mine difficult coal reserves, deposited under unfavourable geological conditions with higher economical and socio-ecological efficiency than that in conventional coal mining, in view of these the basic principles and concepts of coal mining and coal utilization for energy generation should be reconsidered taking into account the latest achievments in underground coal gasification/combustion, coalbed methane extraction, clean coat technology and advanced developments in environmental engineering. The authors have developed a new concept of ecologically clean and resource saving coal-gas electricity, protected by a patent of Russian Federation (1995). The main principles and technological features of these conceptual technologies are explained hereupon. It should be a break through into a coal mining technology of new generation, which is known as unconventional coal mining technology. Under current global energy policy, transection to the new generation of coal mining technology is inevitable. Now we are standing at the treshhold of the coat's regeneration based on integrated unconventional coal mining and innovative coal fueled electric generation technologies.

Feb 24, 1997

By M. Schafer

The 6-m- (20-ft-) diameter cast-in-place tunnel lining for Phase 3 of the Mill Creek Tunnel (MCT3) has been completed. This article summarizes aspects of liner design and ad-dresses the construction approach in placing the liner in areas of tunnel that experienced crown overbreak. Tunnel lining production rates, installation procedures and form buoyancies experienced during concrete placement will also be presented. The Mill Creek Phase 3 tunnel (MCT-3) is expected to be completed this year. It is one of the largest tunneling projects undertaken by the Northeast Ohio Regional Sewer District (NEORSD) to date. The tunnel horizon is situated within the Devonian Chagrin Shale rock formation at an average depth of 85 m (280 ft). The tunnel was excavated using a two-pass method. A full face, fully shielded, Robbins 7.2-m- (23.8-ft-) diameter tunnel boring machine (TBM) was used to excavate approximately 4,500 m (15,000 ft) of tunnel and facilitate installation of initial supports (first pass). The final lining (second pass) consists of 305-mm- (12-in.-) thick cast-in-place reinforced concrete and integral low flow channel. Seven shafts were constructed on the project. The excavation of the tunnel commenced at Shaft 14 and proceeded down grade to Shaft 9, the terminus shaft. Because of the presence of overbreak in the tunnel crown, measures were required to support the form and counteract the effects of buoyancy during concrete placement.

Jan 1, 2008

By K. W. Lee, C. Pound, J. Carmody, L. Petersen, C. Nelson, J. G. Cai

The feasibility of developing the Underground Science City below the Kent Ridge Park has been investigated. The primary aim of the study has been to explore the possibility of creating underground space to house a new community of research laboratories and offices. The investigation represents the first such study undertaken in Singapore for a non-military underground facility. The paper describes the geology of the Underground Science City site and illustrates the layout and plan of the Underground Science City. The geology and rock mass below the Kent Ridge Park is generally favorable for the development of an underground cavern complex. Underground Science City can be potentially developed housed in a cavern complex. Several potential development schemes are studied; with various combination of deep/shallow mined caverns of different span sizes and access options. The preferred scheme is shallow, mined room-and-pillar caverns with large spans and shaft accesses at both existing surface Science Park 1 and Science Park 2. The scheme can be potentially expanded laterally to create more underground space for new Underground Science Cities at Kent Ridge area.

Jan 1, 2001

By Georgene Renner, William R. Yernberg, Steve Kral

ABB provides integrated pro-cess control, optimization and information systems, drives and power-distribution equipment as well as other services and support to the mining industry. ABB also supplies electrical equipment and control systems for the openpit mining industry. This includes products for the automation of electrical equipment in mine shovels. The company offers low- and medium-voltage drives for various mineral- industry applications. And ABB provides gearless mill drives for equipment, such as semiautogenous grinding mills that are too large for conventional drives. ABB Industrial IT provides innovative hardware and software systems that cover all the requirements of the modern mining and processing plant.

Jan 1, 2004

By Larry R. Powell

The Bureau of Mines, in cooperation with the Illinois Mine Subsidence Insurance Fund, is monitoring the response of two foundations to ground movements induced by subsidence from high extraction mining in southern Illinois. The objectives of the monitoring program are to study the inter- action between the ground surface and a foundation during a subsidence event and to determine the capability of the tiltmeter to detect and monitor subsidence movements. Tiltmeter data were obtained on two foundations constructed near Sesser, IL. One of the 30-by 40- ft foundations was constructed with a typical poured concrete footing, the other with a rein- forced-concrete footing poured on top of pol yethylene sheeting placed over a compacted layer of sand. Soil-filled bins were placed on the perimeters of both foundations to simulate superstructure loads. Monitoring pins and tiltplates were installed on the corners and midpoints of the footing. Additional survey points were established on the five-acre site to track the mining advance. This paper describes the monitoring instrumentation and techniques as they relate to the mining and site conditions. The capability of a tilt- meter to detect and follow the tilt of the foundations is demonstrated.

Jan 1, 1986

By Christoph Mueller, Grzegorz Tabak

Basing on five years of experience, this paper discusses modern e-drive systems used in underground transport. This covers Energy distribution and cabling principles, inverters and motors as well as auxiliary aggregates. Also an overview of different regimes for battery charging and the energy management and the method of control of the traction are lined out: This means that throttle and brake are not handled separately, but integrated into “longitudinal control” algorithms which assure that a commanded speed is maintained while synchronizing the multi motor systems and taking into account the constraints imposed by e.g. slope grade and battery parameters.

Jun 25, 2023