Search Documents

By J. J. Taute, N. B. du Preez

"A well-performing solvent-extraction circuit is a key part of producing good quality copper cathode. To ensure consistent operation, a good understanding of the circuit’s operation and an ability to rapidly troubleshoot key parameters is required. This paper briefly discusses the modeling of solventextraction circuits. The paper then goes on to discuss the determination of key performance parameters from plant data and comparing these with the circuit models to quantify circuit performance. The identification and troubleshooting of circuit issues is presented with a worked example. INTRODUCTIONA well-performing solvent-extraction (SX) circuit is a key part of producing good quality copper cathode. To ensure a consistent, high-quality operation, a good understanding of the circuit performance is required. Evaluating the performance of an SX circuit is an extensive topic. The objective of this paper is to focus on the evaluation that the metallurgist should be performing on a regular basis using flow and concentration data. This paper does not cover important topics, such as crud management, phase continuity, or organic management. Some basic SX modeling concepts are first be presented. The calculation of the parameters is then presented with a brief discussion and recommended ranges (where applicable). A worked example is used to provide a basis for further discussion on the evaluation of the calculated parameters and use of data collected.BASIC SOLVENT-EXTRACTION MODELING CONCEPTSThis section presents the basic modeling concepts used in SX simulation packages currently available. SX reagent suppliers have invested significant time and effort into collecting data on the performance of their reagents under different conditions. Based on these data, suppliers have developed packages which they normally make available to their clients for free. These are typically used for process design and plant optimization studies. For example, BASF developed ISOCALCTM and CYTEC Industries developed MINCHEM® and MEUMTM.Chemistry of Copper Solvent ExtractionLiquid–liquid extraction involves the selective transfer of a substance between two immiscible liquid phases by controlling the relative solubility in each phase. In the case of copper SX, the exchange is typically achieved by an oxime-based chelating mechanism. In particular, mixtures of aldoxime and ketoxime are normally used in conjunction with modifiers. More detail on this extensive topic can be found in Schlesinger et al. (2011)."

Jan 1, 2015

By Luis Rudolphy, Pekka Tähkiö

"Flotation plant design, construction and start-up can be challenging tasks, because multiple factors and disciplines have to be combined in an efficient manner, in order to execute a project that meets the technical, financial and timeframe expectations. Key considerations that need to be addressed when designing a flotation plant are process requirements, equipment integrability, automation, and up- and downstream processes/designs. Furthermore, several other lifecycle factors need to be considered, such as servicing and maintainability, operational costs, future expansions and decommissioning, among others. To address these challenges, Outotec has developed a new approach to designing flotation plants that targets eliminating most of the inherent risks that can be found in these types of projects. The new Outotec® plant is a fully modular approach in which the above-mentioned challenges have been taken into consideration in the design phase. As a result, the cPlant concept can give several benefits for new and experienced companies involved in the minerals processing business, such as lower risk investments, fast and cost-efficient flotation plant delivery, faster ramp-up period, easy plant expansions, fully automated processes and operation and maintenance ease. As well, dismantling and transportation of the cPlant to a new location is easy and fast, hence the new cPlant concept makes possible to exploit small, short-lifespan ore deposits and also retreat old tailings ponds that might contain valuable minerals and where the ore quantities are limited. Furthermore, cPlant is easily implemented for brownfields and temporary expansions during bigger expansions."

Jan 1, 2015

By D. Limpitlaw

Industrial mining in Zambia started in the 1930s when the world class copper deposits near the border with Katanga were developed. The discovery of these deposits began at the turn of the century when the first claims in the Copperbelt were pegged at Chambishi, north of what became the town of Kitwe1. World War I and the difficulties of raising sufficient capital for such large scale undertakings delayed the exploitation of these deposits. Following this hesitant start, a large copper mining complex was built, resulting in the development of five major towns, all highly dependent on the mining and beneficiation of copper and cobalt. Copper became so important to the country that, on independence, the only non-mining town to make it onto a list of the top six was the capital, Lusaka. From commissioning of the mines to the end of the colonial period in 1964, copper production increased to just over 640 000 t annually2 (see Figure 1). After the establishment of the new Zambian state, production continued to increase, supported by a benign legislative environment and strong international copper prices. The government of Kenneth Kaunda was intent on improving the conditions of the rural poor and reducing unemployment in urban areas. To this end, the government embarked on an ambitious project of refocusing Zambia's economy away from the colonial role of commodity supply to one of decentralized mass employment. The Copperbelt industrial complex was key to the success of this approach, and in 1969 the Zambian State acquired a 51 per cent stake in Zambia's two main copper producing companies: Roan Selection Trust and Rhodesian Anglo American Corporation. The former became Roan Consolidated Mines Ltd (RCM) and the latter became Nchanga Consolidated Copper Mines Ltd (NCCM). In the year they were nationalized, the mines produced at least 720 000 t of copper? and employed approximately 48,000 workers (see Figure 2)2-4. The subsequent economic policies of the Zambian Government depended heavily on the state's ability to monopolize the proceeds of copper mining.

Jan 1, 2011

By S. M. Rupprecht

"Artisanal mining is basic mining characterized by manually intensive work methods utilizing primitive or simple equipment and conducted by individuals or small groups exploiting deposits. Artisanal mining in Rwanda and Burundi is further complicated in that the techniques applied are often inadequate, resulting in low productivity and poor recoveries, and workers are paid low wages with owners reluctant to reinvest in the mining operations. A consequence of this vicious circle is often poor working conditions, with miners operating under unsafe and/or unhealthy working conditions. An additional problem is that mining is conducted in a manner that is detrimental to the environment.Artisanal mining is commonly more dangerous than large-scale modern mining operations. Artisanal operations are generally subsistence activities with the miners focusing more on immediate concerns than the long-term consequences of their activities. When miners have no other source of income, they will usually find ways to evade controls and carry on working. Machinery tends to be expensive and often far beyond the reach of most artisanal miners, and therefore there is a general tendency for workers to focus on labour intensive and riskier mining methods.This paper proposes the introduction of small-scale mechanization with labour-intensive manual mining utilizing a bench mining approach in artisanal mines operating in Central Africa. From the 1950s to the 1980s bench mining was successfully conducted in Burundi utilizing manual labour. In order to achieve a balance between job creation and project economics, the combination of manual and mechanized mining is proposed. Manual mining offers the benefit of local job creation while ensuring good mining techniques, such as minimizing mining loses and dilution. Through the introduction of mechanized loading and hauling activities, areas of high stripping ratios can be viably mined, thus increasing the amount of resources that can be exploited. The use of a loader and tractor-trailer arrangement is proposed, thereby improving throughput, productivity, and worker safety and, reducing the impact on the environment."

Jan 1, 2017

By P. Amponsah-Mensah

Dilution of ore has a major impact on economics of a mine. The magnitude of dilution depends on mining method, stope dimensions, reef and host rock quality, wall support and drilling accuracy. The main contributing factor is the presence of very weak graphitic shear band of varying thickness in and around the reef. The reef, at Obuasi, is generally steeply dipping and open stoping is the predominant mining method. The stability of the stope walls limits the stope dimensions. Various options for allowing larger stopes for higher productivity and limiting dilution are analysed. The most economic way is to reinforce the walls with systematic cablebolt supports. This option does not only add the support cost but also requires additional cost of access development. These conflicting requirements are continually being optimised at the mine for the economics of dilution control. La dilution du minerai à un impact majeure sur l’économie d’une mine. La quantité de matériel diluant le minerai dépend de la méthode d’extraction, de la dimension des chantiers d’abattage, de la qualité du filon et de la roche mère, du support des épontes et de la précision du forage de production. Le facteur principal qui contribue à la dilution est la présence d’étroites zones cisaillées qui contiennent du graphite ayant différentes épaisseurs à l’intérieur et autour du filon. Le filon, à Obuasi, est généralement à fort pendage et la méthode d’abattage principale est par chantier long-trous. La stabilité des épontes est le facteur qui détermine la dimension des chantiers d’abattage. Differentes options ont été analysées de façon à permettre de plus larges chantiers de manière à augmenter la productivité tout en limitant la dilution. Le moyen le plus économique est de renforcer les épontes avec des cables d’acier cimentés forés de façon systématiques. Cette option n’augmente pas seulement les coûts de support mais aussi les coûts de développement. Ces besoins contradictoires sont continuellement revisés à l’opération afin d’optimiser l’économique par le contrôle de la dilution. Verdünnung des Erzes hat eine spürbare Auswirkung auf die Ekonomie einer Grube. Die Größe der Verdünnung hängt von gewinnenmethode, von den Stopemaßen, von der Reef- und Wirtsfelsenqualität, von der Wandunterstützung und von der bohrengenauigkeit ab. Der beitragende Hauptfaktor ist das Vorhandensein einer sehr schwachen graphitic Scherbandes unterschiedlichen Stärke in und um der Reef. Der Reef, bei Obuasi, taucht im allgemeinen steil ab und geöffnete Aufstemmung ist die überwiegende gewinnenmethode. Die Stabilität der Wand begrenz die Stope grösse. Verschiedene Wahlen für das Erlauben der größeren Stopes für höhere Produktivität und das Begrenzen von Erzesverdünnung werden analysiert. Die ökonomischste Weise soll die Wände mit systematischen Kableankerbolzenunterstützungen verstärken. Diese Wahl addiert nicht nur die Kosten der Unterstützung aber erfordert auch zusätzliche Kosten fuer Zugangsentwicklung. Diese kontroversen Anforderungen werden fortwährend an der Grube analysiert um die Verdünnungkontrolle zu optimieren.

Jan 1, 2003

By J. Jacobs

The three-product cyclone was originally developed in Russia and is now extensively used in China. The cyclone has recently entered the South African coal industry, and with the obvious advantages that this item of process equipment offers our ever-evolving industry it is safe to assume that it will add value to dense medium circuits in South Africa. Some of the possible applications include: ? Producing multiple products using a single dense medium circuit. These can typically be a primary product with calorific value of 27.50 MJ/kg and a secondary (middling) product with a calorific value of 22 MJ/kg ? High-density separation with a low circulating medium density. Anglo Thermal Coal and Exxaro have pioneered the use of these units at Umlalazi and New Clydesdale respectively. Extensive test work has been performed at Umlalazi to determine the efficiency of the unit and to determine how it compares with the conventional DSM (Dutch School of Mines) cyclone. Some people in the coal industry were initially sceptical and expected the performance of the three-product cyclone to be inferior to that of the conventional dense medium cyclone. The results of the test work have, however, shown that the efficiency of the unit is comparable to that of the cyclones currently employed. A valid concern expressed is the control over the cut-point density of the second stage separation, and work is on-going to find the optimal way to control the secondary separation density. Theoretically, the secondary separation density can be manipulated by changing the orifices of the unit, especially the spigot of the secondary stage. This remains to be proven, and a series of tests is currently being planned. Whatever the result of these tests may be, the three-product cyclone definitely has a place in the South African coal processing industry as it offers a low OPEX and CAPEX solution for producing multiple products from a single circuit, as well as the ability to operate at very high separation densities, while making use of low-density circulating medium. Keywords dense medium separation, DSM, three-product cyclone, coal processing.

Nov 1, 2013

"Pressure leaching is an option for copper recovery from chalcopyrite. Leaching takes place at high temperatures and pressures in the presence of an oxidizing agent. This work shows how the performance of pressure leaching circuits may be improved by optimizing the configuration of autoclaves and the heat removal method. The objective was achieved by creating an autoclave model that combines mass balances, energy balances, and population balances. A base case circuit consisting of a single autoclave was chosen, and this base case was compared with options for increasing capacity by adding more autoclaves to the circuit. These capacity increase options include circuits in which the additional autoclave is added in parallel, in series, and in series with thickening between the two autoclaves. The copper extraction, productivity, and cooling requirements for these options are compared. The series circuit with interstage thickening has the highest extraction and productivity; however, the cooling duty in the first autoclave is high. In addition to comparing circuit options, three options for heat removal were investigated: cooling coils, quench water, and flash recycling. The flash recycle option results in the highest copper extraction, and the quench water option the lowest copper extraction. IntroductionBackgroundCopper sulphide ores and concentrates containing chalcopyrite are typically hard to leach under atmospheric conditions. Smelting of these ores may also be a challenge, due to the inability of smelting processes to handle low-grade ores, as well as impurities such as arsenic and antimony. Alternative hydrometallurgical routes to treating chalcopyrite are therefore required. One option is pressure leaching, which is the focus of this work.In the pressure leaching process, sulphide ores and concentrates are leached in autoclaves at temperatures of 200 to 220°C and a pressure of about 3000 kPa (Schlesinger et al., 2011). An oxidizing agent, usually oxygen, is required to oxidize sulphide ions to sulphate ions. The oxidation of sulphur to sulphate is exothermic; consequently, a method of heat removal is necessary in order to maintain the temperature in the autoclave."

Jan 1, 2016

By T. K. Roy

INFACON XI has no doubt earned the distinction as the first such Congress in India. This prestigious occasion could become a reality of a long cherished dream of the Indian Ferroalloy Producers, consumers and ex-porters. The International Committee of Ferro Alloys (ICFA), South Africa, the august body for organising INFACON, every three years, could be convinced by the Indian Ferro Alloy Producers? Association (IFAPA) to award INFACON (XI) to India. This Congresss, organized by IFAPA, has opened a window for the Ferroalloy Community of India, the up-coming Asian Tiger, to register their strength and weakness to the world forum with the principal objectives of evolving long and short-term optimum road-maps for development. It is to be reckoned that India is poised to be a steel giant by 2020 when it is envisaged that the steel production may reach a level of 120 million tons of which significant proportion has to be in the categories of alloy and special steels, requiring standard and high grade ferroalloys. Keeping the above objective in view, the theme of this Congress has been rightfully designed as ?Innovations in Ferro Alloy Industry.? This Congress has also earned a distinction of more than eighty papers, finally selected for inclusion in the Proceedings. More than 100 internationally and nationally reputed experts in the field of ferroalloys (technology and manufacturing practices as well as world scenario) have been approached for critical review of abstracts and selection for the proceedings. It needs to be mentioned without the cooperation received from ICFA the high standard of INFACON could not have been assured. The papers are suitably grouped under seventeen heads, starting from world situation to production and operation followed by present and future technologies and finally to modelling and simulation. It is a Herculean task to the Technical Committee to fit these papers in proper sequence. The Commit-tee members kept no stone unturned to ensure the cogency with the subject matters and at the same timekeeping the flexibility of interests of the participant, especially in the context of three parallel sessions. The Proceedings containing only refereed papers of high quality, will serve the entire gamut of ferroalloy industry and will also highlight the present status of concerned countries. The areas of attention to make the industries globally competitive and at the same time laying emphasis on the prevailing practices, will help the industry leaders to formulate an appropriate global approach. Following the break-through step, instilled by INFACON XI, the Proceedings will be available both in bound and in searchable electronic CD-ROM format. I, as the Chairman of the Technical Committee would like to express thanks and high appreciation to all the Committee members for their whole hearted efforts in all respects without which it would not have been possible to complete these proceedings in the scheduled time. Technical Committee desires to place on record their gratitude to Organising Committee for their synergic cooperation all through in successfully executing multifarious tasks, associated with such a grand international technical Congress.

Jan 1, 2007

By M. Helm

Over the last 40 years, numerous investigations have focussed on the preg-robbing capacity of carbonaceous material during gold ore processing. Various techniques have been applied to characterize the physical and chemical properties of the carbonaceous material in efforts to predict its preg-robbing capacity. The present study, which forms part of an ongoing investigation, is specifically designed to increase the understanding of preg-robbing in ores containing carbonaceous material. In excess of 100 samples from 13 gold mines located in major gold provinces of the world have been incorporated into the present study. These samples were characterized using industry standard metallurgical techniques and were shown to have gold adsorption capacities ranging from a few grams to many hundreds of grams of gold per ton of ore. Further analysis showed that the crystalline nature of the carbonaceous material, which is related to its geological history, is important in determining the preg-robbing capacity of an ore. This finding builds on the common understanding that the preg-robbing behaviour of an ore is related to the amount (or abundance) of carbonaceous material present in that ore. In this study, Raman spectroscopy was used to evaluate the physical nature of carbonaceous material. This is a tool which has been successfully applied by researchers for the characterisation of carbon materials, with respect to crystallite size and lattice defects. Raman analysis of the samples included in this study showed varying degrees of disorder in the carbonaceous materials from the different deposits. Comparison of the Raman spectra with the gold loading capacities of the samples indicated a direct relationship between the structure of the carbonaceous material and its capacity to preg-rob gold. From this, a simple and robust method has been developed based on the Raman spectra of the sample and carbonaceous material content to predict the preg-robbing capacity of an ore. The potential exists to develop a predictive tool using Raman spectroscopy for characterising the preg-robbing capacity of an ore. Such a tool would have potential application in projects ranging from the early stage of exploration through to more detailed feasibility studies and mining operations. The result of applying the predictive method outlined in this paper would be the effective and proactive management of the deleterious influence of carbonaceous material on gold recovery in mining operations.

Jan 1, 2009

By J. Güntner

Most copper/cobalt ores from the Central African Copperbelt contain sulphidic compounds, which are not extractable in direct leaching. Roasting provides the possibility to transfer the valuable components into leachable compounds. In an operation window defined by temperature and off-gas composition it is possible to selectively oxidize iron sulphides to haematite and copper/cobalt sulphides to sulphates. Selective sulphating of the valuable minerals is an important condition for the subsequent leaching stage. The dissolved copper and cobalt are recovered by solvent extraction and electrowinning. This technology has been part of an established process for many decades. The concentrates from recent projects on the Copperbelt have lower sulphur contents, and frequently higher copper contents, than those from older projects. The paper shows the consequences of this trend for plant operation and explains useful counter actions by means of case studies. Autothermal combustion is ensured even at very low sulphur contents. Off-gas treatment has so far been based on SO2 removal through sulphuric acid production. The generated acid is used to make up acid losses in the hydrometallurgical plant section. This well-proven process combination is still the preferred route if the feed sulphur content is high enough; however, some cases may require different off-gas cleaning concepts without compromising on clean air quality. Roasting in a fluid-bed furnace remains the core of the technology. Fluid-bed roasters are easy to operate and provide an excellent control of the calcine quality. Different feeding and heat-recovery systems are used to provide a tailor-made solution for each project. Outotec built it first sulphatizing roaster in Zambia about 30 years ago. At that time, the roasting of metal sulphides was already one of the main technologies in the company. Outotec has developed roasting solutions for copper, gold, zinc, lead, molybdenum, and pyrite ores. The continuously expanded and upgraded research facilities provide an excellent basis for developing sustainable, energy-efficient, and economic solutions for copper and cobalt production in Africa.

Jan 1, 2012

By G. T. Lineberry, C. M. Baird, D. L. Silverstein

The University of Kentucky (UK), with an enrollment of 25,891 in fall 2002, is a comprehensive, public land-grant university located in the Bluegrass Region of Central Kentucky. As the State’s flagship university, UK has long been involved in distance education, first through traditional correspondence courses, followed by use of videotape and satellite delivery in the 1970s and1980s, but soon supplanted by use of interactive television (ITV) and on-line course delivery in the 1990s to date. Today, UK Distance Learning Programs annually administers approximately600 course sections, with services provided to over 5200 enrollees. Courses are offered via six media: interactive video, Internet, on-site, satellite, open-air and cable television, and videotape, with hybrid delivery becoming increasingly popular. The University of Kentucky College of Engineering experience with distance instruction prior to 1985 was limited to videotape non-credit offerings. The Department of Mining Engineering, a small department in terms of numbers of both faculty and students, was a University pioneer in distance education. The first University degree program offered in its entirety by distance delivery(initially by itinerant faculty) was the Master of Mining Engineering. Satellite delivery from Lexington to Cumberland, Kentucky, was a welcomed change of delivery mode in 1987–88,resulting in six hours less travel time for faculty each week. Shortly thereafter, other initiatives directed toward fulfilment of its land-grant mission were undertaken by the College. Use of satellite for course delivery rapidly declined due to limited interactivity, in favour of compressed video and on-site instruction. Classroom sites in the Kentucky Tele-Linking Network (KTLN) now number over 200. The Network links schools, colleges and universities, as well as public and private agencies throughout the State. The KTLN supports voice, video, and data transmission in a uniformly-equipped environment. Beginning in the early 1990s, transfer-critical pre-engineering courses were delivered from Lexington to Kentucky’s community colleges with the largest pre-engineering enrolments. Success was limited, but lessons learned were invaluable. In 1996, the University of Kentucky College of Engineering was asked by the Kentucky Council on Higher Education (the predecessor to the Council on Postsecondary Education) to expand engineering education in Kentucky, first by initiating cooperative B.Sc. degree programmes in Chemical Engineering and Mechanical Engineering on the campus of Paducah Community College (PCC), located 400 km from the UK campus in Lexington. The third partner in these programmes is Murray State University (MuSU), a public regional comprehensive university 80 km south of Paducah. The genesis of the new degree programmes, which were subjected to ABET review in October 2002, as well as a summary of the major accomplishments and challenges of the innovative programmes, will be offered. The limited use of distance technologies for course delivery in these B.Sc. degree programmes will be discussed. A ‘no-spin’ overview of other non-traditional distance-learning ventures within the College of Engineering will be chronicled, with an honest assessment of the motivation for these efforts and, where appropriate, their relative degree of success. Among these ventures are: a BScME and a Master of Engineering programme at Toyota Motor Manufacturing of Kentucky, Georgetown, Kentucky; course exchange in Chemical Engineering between the University of Kentucky and the University of Louisville; an ITV-based Master of Engineering programme for practicing engineers in Kentucky; proposed joint-degree programmes in Civil Engineering and Mechanical Engineering with Western Kentucky University; and a proposed part-time MScME programme in Paducah, Kentucky, with a start date of August 2002, threshold enrolment permitting. Keywords: distance learning, distance education.

Jan 1, 2003

By Y. H. Suh, H. C. Lee, D. S. Kim

A progressive karst formation and its influence upon engineered structures in the ‘phil-karst’ rock mass draw a tunnel engineer’s special attention to a long-term stability and the maintenance issues. Karst sinkholes of any size beneath the railway bed cause train wrecks or long interruptions in train traffic during rehabilitation work. The collapse of cave roof, called a ‘doline’, is in general connected to the cave by the gradual dissolving of the rock, developing into subsidence and sink-holes. The principal conclusions obtained from the field experiments are as follows: It is found that the development of karst cavity shows a relationship with a structural geological line and it is necessary to define the dominant directions of joint and geological layer (formation). The relation-ship between the water flow and joint direction can be used as an indicator of cavity presence in their direction. In addition the direction of in-situ stress can play a role in the development of karst cavities. A risk map of karst scenario is produced for the tunnel supporting systems with rock type classifications in water-soluble karstic rock mass. Eine fortschrittliche Karst-Formung und sein Einfluß auf angelegten Strukturen in der Phil-Karst-Felsenmasse wecken einem Tunnelingenieur eine besondere Aufmerksamkeit zu einer langfristigen Stabilität und der Wartungsausgaben auf. Karstensinkhöhlen in irgendeinen Größen unter dem Eisenbahnbett sind die Ursache der Zugeszerstörung oder der langen Unterbrechungen in Zugverkehr während Rehabilitationsarbeit. Der Zusammenbruch von Höhlendach, d.h. ein “doline”, ist im allgemeinen an die Höhle, die durch das allmähliche Auflösen des Felsen zu entstehen ist und sich in die Subsidence und Sinkhöhlen entwickeln, angeschlossen. Die Hauptschlüsse, die von Feldenprüfungen erhalten wurden, sind folgendermaßen: es wird gefunden, daß die Entwicklung von Karstenhöhlung eine Beziehung mit einer strukturellen geologischen Linie zeigt und es notwendig ist, die vorherrschenden Richtungen von Gelenk und geologischer Schicht (die Formung) zu definieren. Die Beziehung zwischen dem Wasserablauf und der gemeinschaftlichen Richtung kann als ein Anzeiger von Höhlungsanwesenheit in ihrer Richtung benutzt werden. Zusätzlich kann die Richtung von In-Situ-Spannung eine Rolle in der Entwicklung der Karstenhöhlungen spielen. Für das Tunnelunterstützungssystem, welches mit Felsentypenklassifizierungen in wasserlöslicher Karstic-Felsenmasse, ist eine Risikokarte von Karstenszenar hergestellt. Une formation progressive de karst et son influence sur les structures tracées dans la masse de roche "phil-karst" retiennent l'attention particulière des ingénieurs de tunnel aux problèmes de la stabilité à long terme et du maintien. Les creux de karst de toute la taille sous le chemin de fer causent les accidents de trains ou de longues interruptions pendant le travail de réhabilitaion. L'effondrement du plafond de caverne qui s'appelle "doline" s'est, en général, connecté à la caverne par dissolution progressive de la roche, en devenant l'affaissement et les creux. Les conclusions importantes venant des experimentations sur le terrain sont suivants: d'abord, le développement de la cavité de karst montre le rapport avec la ligne géologique de la structure et il est nécessaire de définir les directions dominantes du joint et la couche(formation) géologique. La relation entre l'écoulement de l'eau et la direction du joint peut être utilisé comme un indicateur de la présence de la cavité dans leur direction. De plus, la direction sur place peut contribuer au développement des cavités de karst. Le plan risqué de karst s'est produit pour le système d'appui du tunnel avec les classifications du type de roche dans la masse de roche karstique qui est soluble dans l'eau.

Jan 1, 2003

By J. O. Roux

The Impala Platinum Limited Base Metals Refinery in Springs, South Africa, refines convertor matte containing base metals and PGM?s (platinum group metals) using a hydrometallurgical process. In addition to a PGM-rich concentrate that is further refined, the Base Metals Refinery produces nickel (in powder or briquette form), copper cathodes and cobalt powder. Five leaching stages are utilized to remove the base metals and impurities from the PGM concentrate. The project described in this paper involves a radical redesign of the second stage leach autoclave with the aim of reducing maintenance costs and downtime, increasing throughput and ensuring a safer working environment. The second stage leach process at the Base Metals Refinery, produces a PGM-rich residue through the extraction of copper and any remaining base metals from the first stage leach solid residue material. Leaching is performed in an autoclave operating at a pressure of 600 kPaG and a temperature of 140°C to 150°C. Concentrated H2SO4 is added to the feed to produce a solution with a free acid content between 10 and 30 g/L and a pH of less than 2. Oxygen is passed into the 1st and 2nd compartments of the autoclave. As a result of the aggressive, highly oxidizing conditions within the autoclave, the original design utilized a heavy wall carbon steel shell with lead lining and two layers of acid bricks. The bricks acted as a wear resistant material and ensured a low surface temperature at the skin of the lead lining, whereas the lead lining acted as a corrosion barrier to protect the steel shell. These brick lined autoclaves were heavy, maintenance intensive and prone to catastrophic failure. A radical autoclave redesign was needed to reduce the high costs of manufacturing, installation and operation. Finite element modelling was used to optimize the design and various high alloy materials were investigated for the application. Based on extensive test work, the carbon steel shell was replaced with duplex SAF 2205 stainless steel in the new design. The use of this highly corrosion resistant material, eliminates the need for the lead and brick linings and reduces the wall thickness requirements substantially, resulting in an increase in the available volume for the same external shell dimensions. The vessel is welded in circular sections to form an elongated, impermeable, cylindrical body, with several agitator nozzles and compartments. The first new duplex stainless steel unit has been in continuous operation for more than 24 months and its performance has exceeded the highest expectations. The design was so successful that a patent has been registered. The major benefits of the new stainless steel design include increased throughput, improved performance, less downtime and a safer working environment. Lead has been eliminated and replaced with a more environmentally safe material, and the total lifespan of the vessel has been extended. In addition, the autoclave project has made significant developments in advancing the field of welding and optimizing the integrity of welding quality standards in South Africa.

Jan 1, 2009

By M. J. Kanda

"The design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. This is commonly done using two well-established methods – limit equilibrium and numerical modelling. The research described in this paper compares the outputs of analyses using these two methods with regard to factor of safety and probability of failure, taking into account technical factors associated with each method and other factors such as material parameters and their variabilities. Results show that technical factors such as number of slices and slip circles, number and type of finite elements, and the stress reduction factor can all affect the results of stability analyses. Factors not taken into account in limit equilibrium analyses, such as dilation, in situ stress, and locked-in stresses can affect the outputs significantly. The research has focused particularly on the predicted location of the failure surface, the resulting volume of failure and, most significantly dependent on this volume, the predicted risk associated with slope failure. The results presented show that there is good agreement between the outputs of the two methods regarding factor of safety and probability of failure. However, the same is not the case with regard to volume of failure and hence risk, which can be very dependent on the methods of analysis and their input parameters. The research is not exhaustive, and there are many other factors that could affect the results of slope stability analyses that were not investigated. Some such factors are mentioned in the paper.IntroductionThe design of rock slopes in the planning and operation of open pit mines and for road and rail cuttings requires the evaluation of their stability. The traditional method of stability analysis used limit equilibrium (LE) methods, and this approach continues to be used. Numerical modelling (NM) packages are now also commonly used in slope stability analyses. The outputs from these analyses provide the factor of safety (FOS) and probability of failure (POF) of the slope. Since the capabilities of the two approaches are different, there can be some variations in FOS and POF outputs and in the predicted location of the failure surface. These variations can affect the predicted volume of failure, and this could in turn have a significant effect on the risk associated with the potential failure (Read and Stacey, 2009). Researchers such as Chiwaye and Stacey (2010) have found that LE analyses underestimate the predicted failure volume, unlike NM methods."

Jan 1, 2016

A banquet, attended by 467 members and visitors, was held at the Wanderers Club, Johannesburg, at 8 p.m. on Friday, 21st March, 1969, to celebrate the 75th Anniversary of the founding of the Institute. Introduction of Dr Carel de Wet R. C. J. Goode (President) Dames en here: Ons het 'n aantal vooraanstaande gaste in ons midde vanaand en mnr Maxwell sal u later meer van hulle vertel. Dit is my aangename plig om u voor te stel aan sy Edele, die Minister van Mynwese, van Beplanning, en van Gesondheid, Dr de Wet en sy gade, mev de Wet. Sy Edele Dr de Wet het geen bekendstelling nodig nie-alhoewel hy ons minister vir slegs die afgelope twee jaar is, het hy reeds talle funksies van ons Mynbedryf bygewoon en het baie vriende gemaak onder ons. Hy het homself baie bemind onder ons gemaak toe hy Wes-Driefontein onlangs besoek het om hulle ondersteuning en aanmoediging aan te bied in hulle uur van nood. The Honourable Dr de Wet was born in the Free State. He is a grandson of that very famous general Christiaan de Wet, who caused so much pain to the British forces and for so many months so successfully eluded them in the Transvaal and Orange Free State. He was educated at both the Pretoria and Witwatersrand Universities. He first practised medicine at Boksburg and then moved to Vanderbijlpark, so you see he has an early association with gold mining on the Witwatersrand, and in moving to the Vereeniging-Vanderbijlpark district he became closely involved in our coal mining and metallurgical industries. South Africa's first steel was poured from a l0-ton open hearth furnace belonging to the Union Steel Corporation in Vereeniging in 1913. Dr de Wet has been mayor of Vanderbijlpark and for several years has been their member of parliament. More recently, the Honourable Dr de Wet has filled with great honour that most important office of Ambassador for the Republic of South Africa in London. At present he wears two hats, in that he is Minister of Planning and of Health, but more important is his cloak, that of Minister of Mines, which I trust offers him the greatest comfort. To fulfill these three arduous tasks must demand of him a terrific devotion to duty, and in doing this he carries on that loyal tradition of service to his fatherland so evident in his grandfather. Dames en here, dit is vir my 'n groot genoeë om Sy Edele Dr de Wette vra om 'n heildronk in te stel op die Instituut vir Mynwese en Metallurgie. Toast to the Institute of Mining and Metallurgy Dr the Honourable C. de Wet (Minister of Mines): Mr President, ladies and gentlemen, Mr President you have introduced me gracefully to this distinguished company and I am appreciative of your remarks. I am fully conscious of the responsibilities that devolve upon me as Minister of Mines in a country where mining makes so vital a contribution to economic progress and development and has, in fact, laid much of the foundation on which our present proud edifice is built. The achievements of the mining and metallurgical industry in its diversified activities arouse feelings equivalent to paternal pride, but let me speedily add that in considering any family relationship that may exist, the Minister of Mines should not be regarded in the role either of a fairy godmother or an indulgent father.

By D. Duncanson, R. J. Davidson, C. G. S. Schmidt, G. A. Brown, J. D. Taylor, N. W. Hanf

The development of a cyanidation route for the treatment of gold-plant gravity concentrates is described. This work was carried out as a natural consequence of earlier improvements to the recovery of gold in the gravity sections of existing gold plants. Concern about the environmental aspects of the conventional amalgamation process was further motivation in the development of an alternative procedure. It was found that the partial pressure of oxygen in solution was the most critical reactionrate determining factor. The rate of gold dissolution was shown to be controlled by the reaction rate below approximately 25°C and by diffusion above that temperature. Thus, the efficiency of pulp agitation and oxygen partial pressure permitted a high degree of control over the rate of gold dissolution. The use of oxygen rather than air significantly increased the dissolution rate of both gold and silver. The solubilities of sodium, calcium, and potassium aurocyanide complexes under simulated reaction conditions were studied, and it was established that the values for the sodium and calcium complexes were limited, requiring the use of lower pulp densities and higher reaction temperatures for the treatment of very high-grade concentrates. The presence of excessive amounts of tramp iron in such concentrates of up to 25 per cent by mass was found to result in poor gold dissolution owing to the cementation of gold under certain reaction conditions. The maintenance of high oxygen partial pressures, together with high cyanide concentrations, high pH levels, and the presence of calcium in the system, all aided in passivating the tramp iron. Copper, gold, and iron were shown to be the main cyanide-consuming elements. Optimum gold dissolution was obtained in a closed bench-scale reactor incorporating a flotation-machine type of agitator for effective pulp agitation and oxygenation, the oxygen being recirculated. The reactor was designed to operate under a very small positive pressure. After reaction times of 2 to 6 hours at temperatures in the region of 30°C, both the gold and the silver dissolution averaged 99,S per cent. In the case of very high-grade concentrates, it was shown that gold could be floated in the same reactor by drawing off the flotation concentrate through a port in the reactor. A flotation recovery of 87,4 per cent of the gold in 3,9 per cent by mass was obtained. The recovery of osmiridium from cyanide-leach residues and the electrowinning of gold from the pregnant liquors were also considered as processing aspects in the treatment of gold-plant belt concentrates. Final table tailings with a gold concentration of 10to 12 gft were obtained. The results of the investigation strongly suggested that an alternative cyanidation route for the treatment of gold-plant concentrates was technically feasible, provided the system included effective agitation and oxygenation. In the case of lower-grade concentrates, cyanidation followed by the electrowinning of gold appears to be the simplest route, while, for high-grade concentrates, flotation and smelting of the concentrate followed by cyanidation of the flotation tailings are suggested. The use of oxygen rather than air for sparging the pulp would depend largely on the grade of material to be treated. A preliminary comparison of the costs related to the amalgamation and cyanidation processes for the recovery of gold from such concentrates indicated very similar capital and operating costs. It was concluded that other considerations, e.g. toxicity, safety, and lower labour requirements, were more important than such small cost differences. Furthermore, the 'opening' of the gold-plant gravity circuit, which would be made possible by a cyanidation route, would further reduce the operating costs because of the subsequent decrease in the tonnage to be treated.

Jan 1, 1978

By G. Poropat, A. R. Guest, H. P. Grobler

At the De Beers Consolidates Mines operations it is common practices to perform Geotechnical mapping of the newly exposed faces in the waste and ore rock. The purpose of Geotechnical mapping is to quantify the in-situ fracturing of a rockmass that in turn is required during the planning and application of a mining method. Whether it is to determine slope angles, caveability, impact of blasting or support requirements. This mapping involved a cumbersome and time consuming procedure that requires individual examination and description of the natural inherent fractures exposed by mining. During highwall mapping in an open pit this can be a safety concern due to the duration of time spent below a highwall. The advantages gained through the recent introduction and application of SiroVision® allows safer mapping, an increase in statistical fracture population, archiving of rock faces and the more accurate reflection of the true mapping. This paper aims to describe in detail the application of the recently developed SiroVision®, photogrammetry software, to replace conventional face mapping. A De Beers Consolidated Mines, il est pratique courante de faire une cartographie géotechnique des tailles récemment exposées dans le rocher stérile ou minerai. Le but de la cartographie géotechnique est de quantifier la fracturation in-situ d’une masse rocheuse, qui sera nécessaire lors de la planification et application d’une méthode minière, que ce soit pour déterminer les angles des galeries inclinées, les possibilités de foudroyage, l’impact du dynamitage, ou les besoins en supports. Cette cartographie nécessitait une procédure longue et compliquée qui demande l’examen individuel et la description des fractures naturelles propres exposées par l’opération de mine. Pendant la cartographie de parois dans une exploitation à ciel ouvert, cette opération peut être dangereuse à cause du temps passé sous la paroi. Récemment, le lancement et application de Siro Vision apportent l’avantage d’une cartographie plus sûre, une augmentation des statistiques de population de fracture, l’archivage des tailles de roches, et le reflet plus précis de la cartographie. Le but de l’étude présente est de décrire en détail l’application du développement récent de Siro Vision, logiciel de photogrammétrie, pour remplacer la cartographie de taille conventionnelle. Bei den De Beers Consolidates Mines Operationen ist es gängige Praxis geotechnische Aufzeichungen des Taub- und Erzgesteins neu geöffneter Abbaustellen zu erstellen. Zweck dieser geotechnischen Aufzeichnungen ist die vor-Ort-Quantifizierung des Bruches der Gesteinsmasse, welche im Gegenzug während der Planung und der Anwendung einer Abbaumethode erforderlich ist, sei es um einen Neigungswinkel festzustellen, Abbaubarkeit, Auswirkung von Sprengungen oder Anforderungen an Unterstützungen. Die Aufzeichnungen waren mit umständlichen und zeitaufwendigen Prozeduren verbunden, die eine individuelle Prüfung und Beschreibung der durch den Abbau freigelegten natürlichen inhärenten Brüche, verlangten. Dies kann auf Grund des Zeitraumes der unterhalb einer Flözoberschicht verbringt wird zu einer Frage der Sicherheit werden wenn die Aufzeichnung einer Flözoberschicht im Tagbau erfolgt. Die Vorteile auf Grund der jüngst erfolgten Einführung und Anwendung der SiroVision® gestatten sichereres Aufzeichen, eine Zunahme in der statistischen Menge an Gesteinsbrüchen und eine akkuratere Reflektion der tatsächlichen Aufzeichnungen. Diese Arbeit hat zum Ziel im Detail die Anwendung der kürzlich entwickelten SiroVision®, eine photogrammetrische Software, die die konventionelle Abbauortaufzeichnung ersetzen soll zu beschreiben.

Jan 1, 2003

By A. W. S. Schumann

G. H. HENDERSON INTRODUCTION It is a pleasure to have read Mr Schuman's wide ranging and highly informative paper and also to congratulate him. Before proceeding to give views on the use and preservation of coal in South Africa, it is perhaps apposite to look at the South African scene on the world canvas. Mr Schuman's figures in his Table I are highly revealing. The Table shows expected consumption, export and import demand in the year 1980 by the continents of the world. The Republic of South Africa is shown as one of only four exporting countries at that date, although in the interim, Australia has become an exporter and will continue to grow as an exporter of coal. Huge fields have been proved in recent years. There is reason to think that for some years, coal and its economical uses have been under-estimated. The importation of oil carries a constant question mark and the exciting possibilities expressed in the uses of Dranium a decade ago for power generation, appear to have met with some setback. Present indications are that breederreactors will be delayed until about 1990. The capital cost of such reactors, too, is enormous. By 1980 it has been estimated that 20 per cent of the energy required by the leading ten nations of the world will come from nuclear power, but 80 per cent would then remain for fossil fuels and hydro generation. COAL DEMAND AND USAGE It is of interest to record that coal production in all the countries of Europe has declined markedly in the last 25 years. This is due to competition from oil, gas and nuclear power and also for sociological reasons; but there are signs that efforts will be made to resuscitate, at least in some measure, the mining of coking coals for which there is a strong and growing demand. Possibly all hard coal now mined in Germany has coking properties and that country is self-sufficient in this commodity. Germany might perhaps consider selling coking coal to her neighbours and importing additional coal for power-raising purposes. It has been frequently stated in American publications that the coal reserves of the D.S.A. are sufficient for 1 000 years. What that means, I do not know, but it is at least an indication that America has huge reserves of coal. Domestic and export demand in the U.S.A. in 1968 exceeded production for the first time. In 1969, the United States' output amounted to some 556 million tons, an increase of less than 2 per cent on the previous year. The output achieved fell short of demand, domestic and export, by more than 7 000 000 tons. This has caused and is continuing to cause anxiety in the U.S.A. In many countries young men for a number of reasons, largely environmental and social, are not coming forward in sufficient numbers for mining requirements and the same pattern has revealed itself in the Republic. This is, indeed, alarming because mining men in large numbers will be required to meet the estimated tonnage requirements set out in the following Table: It is difficult to visualise the replacement of these coal requirements either by oil or by nuclear fuels. The coal must be mined and men are required for the purpose. Unless a greater section of the population is allowed to participate in the more responsible aspects of mining, there is a serious likelihood that demand will not be matched by output. In addition to local demand, a lively export trade is possible. Exports are dependent on the future capacity of the South African Railways and Harbours and on Government policy. An export figure of 10000000 tons per year during the decade can be visualised and this figure would raise total estimated sales production to a figure of over 100 000 000 tons in 1980. At this point, it is necessary to examine the desirability or otherwise of exporting coal. How much coal

Jan 11, 1970

By D. Lunt

This paper describes and sets in context the commercially proven uranium extraction processes. It also discusses some of the technologies that are currently being pursued with the aim of reducing costs and overcoming a number of technical issues that are faced by process designers and operators. In doing so, opportunities for the transfer of extraction technology from other industries/commodities are identified. The key processing areas that are examined include: ?The influence of mineralogy. The type of uranium mineralization and the nature of its association within a particular deposit will have a major impact on process route selection. Uranium minerals are classified according to their influence on extractive metallurgy. As the uranium price has risen in recent times, so opportunities are increasing for the recovery of uranium from less conventional resources such as phosphates and fossil fuels. ?The opportunities for employing techniques aimed at reducing the capital and operating costs of the overall process such as heap leach and beneficiation. Preconcentration by screening, gravity separation and radiometric sorting can potentially reduce the mass flow to the downstream leach and recovery plants. ?Purification or separation of uranium in carbonate systems. While it is possible to directly precipitate uranium from clarified leachate, the presence of impurities such as vanadium, molybdenum and others may dictate that ion exchange or selective precipitation is employed. Advances have been made in other industries in terms of improved ion exchange equipment aimed at reducing resin inventories and hence costs. ?Separation in acid leach systems. Earlier developments included the use of combined SX-IX systems (Eluex or Bufflex) and the introduction of continuous countercurrention exchange (CCIX). Column SX has found a ready application to uranium in view of the rapid extraction kinetics. With the renewed interest in uranium processing, efforts are being redirected towards further development of resin-in-pulp (RIP) as a means of driving down capital and operating costs. ?Extraction in a chloride environment. Australia and Namibia are desert countries where good quality water comes at a cost. However, both have access to saline water from either the ocean or subterranean aquifers. The issues associated with operating a uranium extraction operation in such environments is discussed. ?Extraction from less conventional sources. Recent price increases for U3O8 have resulted in a number of companies examining the recovery of uranium from sources such as fossil fuels and phosphate deposits. Both of these areas were examined in the 1970s and 1980s and a number of approaches were commercialized. The paper reviews the extraction options.

Jan 1, 2007

By K. -C. Han, S. -Y. Kim

This study was carried out in a bid to survey Ganboke gold mine in Pala, Mayo-Kebbi Province, southwestern Chad. The Ganboke mine is now being prepared for investigation and development, and the research sought to perform rock properties tests of relevant rocks through its geological survey, rock mass evaluation, and in-situ and laboratory tests and analyze the stability by the means of limit equilibrium method, thereby suggest appropriate methods to design the pit slope and individual benches in Ganboke mine. Targenting GS1-GS1' section with the depth of 180 m and GS2-GS2' section with the depth of 150 m in the survey area, we set the height of the bench at 10 m and 15 m, and the angle of bench at 60o and 70o, respectively, and then reviewed the stability for dried condition and saturated condition. The result of examination indicated that it would be appropriate to set the bench height at 10m and the bench angle at 60o in developing the mine slopes concerned. Cette étude est réalisé dans le but de faire des recherches sur Ganboke mine d'or dans Pala, Mayo-Kebbi Provence, Tchad sud-ouest. La Ganboke mine est actuellement en train de étre disposé à la investigation et le développement, et la recherche a cherché à accomplir les tests de la propriétè des roches par l'intermédiaire de la étude géologique, la évaluation de la masse rocheuse, et in-situ et les tests de laboratoire et à faire l'analyse de la stabilité au moyen de la méthode d'équilibre limite, de ce fait à proposer le methodes propres à faire le plan de la pente et les gradins individuels dans la Ganboke mine. Concernant la section de GS1-GS1' avec la profondeur de 180 m et la section de GS2-GS2' avec la profondeur de 150 m dans l'aire d'étude, nous mîmes l'hauteur du gradin à 10 m et 15 m, et l'angle du gradin à 60o and 70o, respectivement, et alors nous avon reconsidéré la stabilité pour la condition sèche et la condition saturé. Le résultat d'examen a indiqué que il pourrait être propre de mettre l'hauteur du gradin à 10m et l'angle du gradin à 60o en développant les pentes de la mine concerné. Diese Forschung wurde um das Gold Bergwerk zu überschauen in Pala, Mayo-Kebbi Provinz, der Südwesten Chad ausgeführen. Das Ganboke Bergwerk ist jetzt zur Erforschung und Entwicklung vorgebereiten worden, und die Forschung suchte zu ausführen die Prüfungen der Felseigenschaft durch geologischen Überblick, Felsmassewertbestimmung, und In-situ und Lavorversuch auf, und analysieren die Stabilität mittelst der Grenzegleichgewichtsmethode, da-durch schlug die angemes-sen Methoden zu entwerfen die Böschungen und die einzelnen Bänke im Ganboke Bergwerk vor. Für den Abschnitt GS1-GS1' mit der Tiefe von 180 m und GS2-GS2' mit der Tiefe von 150 m in der Überblickfläche, wir setzten die Bankhöhe an 10 m und 15 m, und das Bankwinkel an 60o und 70o, beziehungsweise, und dann zurückblickten die Stabilität für die getrockneten Bedingungen und die gesättigten Bedingungen. Das Ergebnis der Untersuchung anzeigte daß es würde angemessen sein zu setzen die Bqnkhöhe an 10m und das Bankwinkel an 60o in der Entwickelungen vom Bergwerk be-teiligt.

Jan 1, 2003