Search Documents

By B. S. Agbenuvor, R. Morrison, V. Jokovic, C. Antonio

Body breakage usually involves breakage of particles by compression between two surfaces or impacted against a rigid surface, with the latter of interest in this current study. This mode of breakage has been identified to be the most elementary size reduction process and the most effective breakage process in comminution devices. It has been found in the literature that the progenies produced from this form of breakage possess a residual velocity at which they move, after the breakage event. In the pursuit of efficiently utilising applied comminution energy, a laboratory-scale breakage device has been developed to deliver precise specific impact breakage using the concept of a fast-moving hammer and a slow-moving particle to effect breakage. The residual velocities of the progenies from the breakage event may be used to generate secondary breakage without further addition of energy if the particle encounters a stiff obstacle such as a steel plate at right angles to its path. To measure the extent of secondary breakage, the steel wall of the device was lined with a rubber material to suppress the second set of breakage events. The performance of the new device is analysed, based on calculated t10 values and measured residual velocities of the moving daughter particles. Testing involving anvils showed a much finer PSD and higher t10 compared to the test involving rubber lining. This finding is corroborated by the measured residual velocities of the progenies. The resulting energies calculated from the measured residual velocities of the progeny were found to be approximately 42-88% of the primary specific impact energy. This retained energy was found to be sufficient for secondary breakage. Keywords: Impact breakage, residual velocity, secondary breakage, energy utilisation

Jan 1, 2020

By J. W. van der Merwe

Technology is advancing at a rate that makes it extremely difficult for the mining Industry to keep pace. Many advances occur within a given piece of technology and often this is missed by the disciplines that could have gained advantage by its implementation. Often this may have been simply an aspect of cost exceeding benefit. However, there are some technologies that potentially have such a far-reaching impact on the mining industry that the benefits simply outweigh the cost. The application of 3D laser scanning in the mining industry has the potential of taking the concept of ?Google maps?? underground. This presents an opportunity where the virtual world of underground can be traversed with relative ease and many aspects of measurements could be obtained without having to visit the working place again, potentially saving countless man-hours and still delivering precision work with significant savings in downtime, stoppages, and exposure to safety incidents. Anglo American Platinum maintains its competitive advantage though the review and application of appropriate technology. This paper describes the 3D laser scanning trial at one of Anglo American Platinum?s new shafts, and goes on to show the benefits encountered through the application and the involvement of the various MRM disciplines.

Jan 1, 2012

By B. Mbuya, A. F. Mulaba-Bafubianda, J. M. Mvita

The paper explains the main effects of input leaching parameters, such as addition of a reducing agent, acidity, agitation, temperature, and leaching system potential, in relation to observed and predicted yields of sought-after cobalt. An artificial neural network coupled with graphical probability networks was developed wherein the abovementioned input parameters were used to predict the percentage of dissolved cobalt. Furthermore, similarities and differences between the Bayesian and neural network approaches in terms of their key outcomes are compared with respect to study of the dissolution of cobalt in sulfuric acid. Key results indicate that there is a need to use neural network results to predict conditions for dissolution of cobalt, while using Bayesian network to explain inferences about conditions of the input parameters, thereby achieving realistic predictions.

Jan 1, 2023

By K. C. Corin, M. Tadie, R. M. Manenzhe

The near depletion of high-grade ores, among other factors, has necessitated the consideration of alternative PGM sources. Various factors in the metallurgical processing of ores result in valuable minerals being lost to the tailings, and hence, PGM tailings are a possible alternative PGM source. However, as the value residing in PGM tailings remains unquantified and uncharacterised, there is a challenge in knowing the recoverable fraction of value contained in PGM wastes. This paper outlines the in-situ techniques of oxygen uptake and EDTA extraction for their possible use for determining the recoverable value in PGM tailings. Both methods have shown efficiency in determining the weathering of sulphide minerals and sulphide-bearing ores. Keywords: PGM tailings, tailing retreatment, oxidation, oxygen decay, EDTA

Jan 1, 2020

By N. Naude, L. S. Leal Filho, M. P. Tshazi

In this paper, the authors performed experiments in the Denver and Leeds laboratory flotation devices at the University of Pretoria at various particle sizes to evaluate the performance of the devices. Quartz was used in a single mineral system at discrete sizes fractions, -25 μm, +25- 45 μm, +45-75 μm, and +75-106 μm. Hydrodynamic analysis, based on dimensionless power and Reynolds numbers, indicated that the Leeds cell required higher power input to achieve comparable flow conditions. Specifically, the Leeds cell exhibited an average power number of 1.03, whereas the Denver cell averaged 0.77 within the same impeller speed range of 1000 rpm–1500 rpm. For comparative flotation performance, impeller speeds were calibrated, resulting in operating speeds of 1200 rpm for the Denver cell and 1400 rpm for the Leeds cell. The cells performed similarly at two coarser-sized fractions. However, some deviations were observed in the finer particle size range. The -25 μm (fine) fraction initially achieved a recovery of only 15%. An additional reagent dosage was required to enhance the recovery of this fraction significantly. These findings highlighted the influence of particle size on flotation recovery. For all experiments, the Denver laboratory flotation cell outperformed (defined by higher recovery) the Leeds device, while still operating at a lower impeller speed. This advantage can be attributed to its impeller-stator design and air dispersion features, effectively overcoming slurry resistance and resulting in superior flotation performance compared to the Leeds cell.

May 27, 2025

By M. Splaine, W. Davison, D. C. Atkinson

"Since 1964, Nchanga Consolidated Copper Mines, Ltd., has been developing and using production scheduling methods for optimizing its metallurgical operations in the short term (up to one year). Medium-range metallurgical planning has been possible only by successive evaluations of a single-year L.P. A modified version of Rosenbrock's direct search technique has now been developed to allow multi-year optimization of both mining and metallurgy for medium-range planning. The modifications to the search technique have produced a marked increase in computational efffciency for this heavily constrained problem in many variables and the system is a usable planning tool, given a reasonably powerful computer. The plans are 'optimum' in the sense that they yield the maximum present value of the operations.Each of the resulting five-yearly mine plans forms the basis for further detailed metallurgical evaluation by the established production scheduling system."

Jan 1, 2014

By A. Rödfalk, P. Bloemer, J. P. Nilsson, N. Brogden

"Reliable and accurate metal transfer information during silicon tapping from an EAF is invaluable for decision-making and process optimization, while obtaining such information safely is a necessity.Elkem Thamshavn Norway, a producer of metallurgical-grade silicon, identified inherent safety problems with gauging fill levels in ladles using dip bars while molten metal was continuously pouring from a rotating EAF. Operator safety was a paramount concern, and an alternative automatic method of controlling the tapped fill level needed to be found.It was also considered that further benefits could be achieved such as monitoring the tapping flow from the EAF in order to identify any clogging, as well as the potential to use the live feed from such a system to assist decision-making regarding work around the taphole area.Agellis Group AB, Sweden, a company with over 30 years of experience in gauging molten metal levels in the metals industry, was able to design a solution for Elkem Thamshavn that would provide the required real-time process data while enhancing operator safety.This paper shows how the Agellis AB EMLI-L system was successfully installed at Elkem Thamshavn’s EAF continuous tapping area, how ladle fill levels were constantly monitored, and how full ladles were replaced by empty ones without the need for operators to be in the tapping area to take level readings. The results were used to compare the accuracy and reliability of Elkem Thamshavn’s current measuring methods with that of the EMLI-L system. The paper also covers how problems such as how to connect, run, and protect cables in and around the EAF tapping area, as well as connector and cabling survivability during the three day refractory pre-bake period, were solved. Finally, the paper discusses the potential production improvements, maintenance requirements, and data integration attainable through the installation of the system, as well as the major safety improvements that have been achieved."

Jan 1, 2014

By L. A. Balzan, M. Kalicinski, F. Nieuwenhuys

GEOSCANs on belt analysers have been widely utilised in iron ore for nearly two decades. Since the first installations in 2003, the availability of accurate and reliable grade data has become standardised across iron ore mines in the Northern Cape, where various streams are monitored continuously to ensure the optimal functioning of plants. Assmang Khumani has been at the forefront of technology adoption and has implemented 19 GEOSCANs at various locations throughout the plant, monitoring run-of-mine, stockyard feed, beneficiation plant feeds, and products. Over the years, collaborative advances in the technology have allowed for numerous benefits and gains to be made. In recent times, there has been a concerted effort on the development of analysis for phosphorus in the material flows, and based on Scantech's experience in the phosphate industry, this element has now been calibrated to achieve statistically acceptable and repeatable accuracies for real time analysis of this element on many of Khumani's GEOSCAN analysers. This paper provides an overview of GEOSCAN use at Khumani, while focusing on the development of phosphorus analysis. A case study of analysis results is presented for a range of analysers that have been calibrated for this element, as well as a discussion on the benefits obtained as a result of this analysis. Keywords: Online analysis, real-time, process control

Jan 1, 2020

By C. Liu, F. Ye

"To extend the variety of lump ores that are used in the COREX shaft furnace and to optimize iron ore blending, the original evaluation method for iron ores that was proposed by Voestalpine AG has been improved. Physicochemical and metallurgical properties of iron ores, including Sishen lump ore and CVRD pellets, which are currently used in the COREX process, and three other lump ores, were assessed and compared. Ore matching principles were proposed and five optimized iron ore blending schemes designed and verified by laboratory experiments to prove the effectiveness of the improved evaluation method. The replacement of Sishen lump ore by the alternative L2 and L3 lump ores without varying the proportion of CVRD pellets could improve the degree of reduction and rate of metallization, and decrease the bonding index. Based on the results of laboratory test work and industrial- trials, an ore blending scheme of 60% CVRD, 20% L2, and 20% L3 is recommended for use in the COREX process. IntroductionIn recent years, problems such as environmental pollution and a shortage of coke and coal resources for blast-furnace ironmaking have become increasingly apparent. Based on sustainable developments in the iron- and steelmaking industries, the environmentally friendly COREX smelting-reduction process with low energy consumption was developed and introduced (Zhou and Du, 2013; Song, Lv, and Yin, 2015; Xu et al., 2016; Kurunov, 2010). The evaluation system for lump ore that was proposed by Voestalpine AG recommends that only Sishen lump ore from South Africa be used in the COREX process, because of the stringent physicochemical and metallurgical property requirements. This situation significantly hampers improvements to the technical and economic aspects of the COREX ironmaking process, especially in China (Eberle, Siuka, and Bohm, 2006). No theoretical or technical basis has been provided for the evaluation system, and the assessment approach for iron ores also presents problems that need to be discussed and resolved.The COREX process consists of two reactors: the prereduction shaft furnace and the melting gasifier as shown in Figure 1 (Wu et al., 2017). Pellets and lump ores which are charged to the prereduction shaft should have a good reducibility and metallization with a low degradation index (Li et al., 2016; Wu et al., 2011; Kumar et al., 2009; Kang, Gupta, and Sahajwalla, 2007). The properties and microstructure of the iron ore pellets which are required to achieve a high productivity and a lower fuel rate in the COREX process have been investigated (Umadevi et al., 2011). Some efforts have also been made to investigate the behaviour of lump ores in the COREX shaft furnace, including the disintegration characteristics and the reduction degradation (Umadevi et al., 2011; Zhou et al., 2015; Xu et al., 2013; Li, Feng, and Zou, 2013; Hou et al., 2014). However, few studies have focused on the optimization of ore blending for partial or total substitution of the expensive Sishen lump ore by other, cheaper lump ores to reduce the production cost. The technology for the utilization of blended lump ores in the COREX process is still in its early development stages (Zhou et al., 2017; You et al., 2017)."

May 1, 2019

By M. de Paiva Bueno, G. Barakos, S. Luukkanen, K. Luolavirta

Lifelong development of skills and knowledge of mining professionals has been recognised worldwide as a challenge for the development of a sustainable mining sector. Practical training and learning over the mine value chain are among the key components of this knowledge building. However, the number of available mining sites for continuous education in real-life conditions is limited; also the specifications for practical training are not clearly defined. The project MINETRAIN was developed to (i) evaluate the potential of the shortly-closing Pyhäsalmi Mine, in Finland, as an educational and training underground facility, and thus, prolong the utility of the existing modern mine site, and to (ii) develop and test practical training programs for mining and mining industry related professionals. Pyhäsalmi facilities enable training among all disciplines related to the overall mine value chain and hence, the project has potential in providing education for sustainable management of any phase of mining operations. The philosophy underpinning the MINETRAIN approach to mining activities is to assist the clients in minimising the technical and financial risks by providing a competitive and skilled personnel asset while optimising the value drivers in their operations. As a first major step of the project, a pilot training course, involving basic-level online theory and hands-on training at the Pyhäsalmi mine site, was undertaken in summer 2019. Feedback from the pilot test group of mining professionals has proved to be very positive. The comments from the participants strongly emphasised the added value of the practical onsite training for improved understanding in the large scale picture of mining on the entire value chain. As a second phase of the project, a new test course was launched in June 2020. The second MINETRAIN course focuses on new technologies and digitisation in mining. Keywords: Lifelong learning, mining education, mine value chain, research and education mine, educational research project

Jan 1, 2020

By G. Akdogan, P. Mutimutema, M. Tadie

The South African gold mining industry has a legacy of abundant tailings dams, which have attracted the attention of investors because of their potential as a cheaper secondary gold resource. In this we investigate study gold recovery from a refractory calcine tailings dam. Bulk mineralogy of the tailings silicates and iron oxides to be the most abundant phases. Scanning Electron Microscopy (SEM) showed gold to exist in submicrometre and micrometre sizes, as free gold, and associated with arsenic, sulphur, and silicates e.g. quartz and talc. Gold recovery by direct cyanidation was low at 17.3%. Mechanical (ultra fine grinding P80 -16μm) and chemical (alkaline, NaOH) pre-treatment and microwave roasting and microwave-assisted cyanide leaching were investigated to increase gold recoveries. Ultrafine grinding was the most effective, producing recoveries of 66.5%. NaOH pre-leaching of ultrafine milled material increased recovery to 71.5%. Alkaline pre-leaching overall increased recoveries for non-pretreated material, making this process the most preferred because it is less costly than ultrafine grinding. Microwave roasting and microwave-assisted leaching did not achieve higher recoveries than alkaline pre-treatment or fine grinding. The investigation highlights and confirms that chemical treatment with NaOH is a powerful tool for gold extraction from refractory tailings.

Oct 1, 2022

By N. C. Steenkamp

Lightning has been observed in dust clouds following open-pit blasting. It is proposed that the occurrence of this phenomenon is related to the physical composition and characterization of the mineral fines that comprise the bulk of the dust cloud. Silicate minerals, which are susceptible to fine fracturing during blasting, generate the initial charge. This is further enhanced by collisions and friction during the turbulent upcast in the post-blast dust cloud. Varying size fractions result in different rates at which these particles drop out of suspension and create a secondary temperature gradient. This results in the creation of two charged zones and increases the potential of developing a discharge in the form of lightning. The ideal prevailing meteorological conditions need to be windless to minimize the effect of particle dissipation and have sufficient moisture toenhance the potential of generating lightning.

Apr 14, 2024

By C. Banff, E. C. F. Hamman, J. Venter

Open pit slope stability analyses for large scale instabilities are often carried out using limit equilibrium, finite element or finite difference computer programs. All of these require empirical estimates of rock mass shear strength when calibrated values are not available, which is a common occurrence. A common method of estimating rock mass shear strength is the Hoek-Brown failure criterion, which often over- or underestimates rock mass shear strength when used in limit equilibrium or elastic linearly plastic slope stability analyses, resulting in published alternative estimates for the coefficients of the Hoek-Brown failure criterion. This paper investigates the differences between limit equilibrium and elastic linearly plastic slope stability analysis based on the Hoek-Brown failure criterion. The investigation consisted of a comparison of 3840 RS2 finite element analysis models completed with strain softening, and 216 Slide2 limit equilibrium models. The models were used to evaluate a methodology to determine equivalent limit equilibrium and elastic linearly plastic shear strength parameters that provide the same stable slope angles and instability back break distances as the more representative strain softening stress analysis methods. This paper presents the methodology and compiles the results into design charts and equations for equivalent limit equilibrium Mohr-Coulomb shear strength parameters, that simplify calibration against actual case studies. The results compare well with older empirical shear strength estimates, however, a detailed calibration of the results against case studies will need to be carried out. The analysis also did not consider pore pressure effects; this is left for future publication.

Sep 1, 2025

By C. A. Snyders

This paper investigates the recovery of platinum group metals (PGMs) from a dilute cyanide leach solution containing base metals, in a manner similar to that used for gold extraction in a typical CIP process, and focuses on both the adsorption and elution stages. The carrier-phase extraction of precious metals using activated carbon offers significant advantages over other processes in terms of simplicity, the high pre-concentration factor, rapid phase separation, and relatively low capital and operating costs. As a sorbent, activated carbon is still by far the most important material because of its large surface area, high adsorption capacity, porous structure, negligible environmental toxicity, low cost, and high purity standards. Adsorption tests were performed on a pregnant alkaline leach solution (0.15 ppm Pt, 0.38 ppm Pd, 0.1 ppm Au) resulting from cyanide extraction performed in column leach tests. The initial adsorption rates of platinum, palladium, and gold were very fast and recoveries of these three metals were approximately 90 per cent after 2 hours and 100 per cent, 97.4 per cent, and 99.9 per cent respectively after 72 hours. The parameters that influence the extraction of PGMs and Au were examined to assess their relative importance during the adsorption process in order to provide the basis for process optimization. The concentration of thiocyanate was not identified as significant factor for PGMs adsorption, while nickel concentration was the most significant extraction process parameter. Base metal cyanide complexes adsorb and compete with the PGM complexes for sites on activated carbon, and while copper adsorption can be minimized by adjusting the residence time, nickel adsorbs at approximately the same rate as that of the PGMs, influencing the loading capacity and adsorption kinetics of the PGMs. The feasibility of eluting platinum and palladium cyanide complexes from activated carbon using an analogue of the AARL process was investigated. Platinum and palladium elute from activated carbon almost to completion in 4 to 5 bed volumes at 80°C, while the elution of gold at this temperature is slow, with a significant amount of gold still to be eluted after 16 bed volumes. Cyanide pre-treatment was found to have a significant influence on PGM elution. Higher cyanide concentration in the pre-treatment step results in more efficient elution up to a point, and experiments suggest the possibility of an optimum cyanide concentration, beyond which elution efficiency starts decreasing.

Jan 1, 2012

By K. Muchima, C. Siame, L. Little, B. Kaputula, Q. Mclennan

"The variability of copper mineralization at Kansanshi mine significantly affects the efficiencies of the processes used to recover copper. Quantifying this variability is therefore essential for monitoring and optimizing the performance of the concentrator, which comprises three different flotation circuits (sulphide, mixed, and oxide) and an atmospheric leach circuit. Onsite automated scanning electron microscopy with energy-dispersive X-ray spectrometry (Auto-SEM-EDS) is used to analyse routine weekly composite samples for each circuit, providing detailed analyses of bulk mineralogy, copper deportment to different minerals, mineral liberation, and associations. Weekly mineralogical trends are used to assess changes in process performance, and characterization of the copper losses has inspired a number of projects to target the specific particle types responsible for the main losses. In this paper we describe the relationship between mineralogy and plant performance at Kansanshi, and discus IntroductionKansanshi is a copper and gold mine located in the Northwestern Province of Zambia, with an annual production in the region of 250 000 t of copper and 160 000 ounces of gold. Ore mined from the epigenetic vein-hosted deposit is classified into three ore types based on the extent of oxidation and supergene enrichment. Sulphide, oxide, and mixed ore are fed to separate mineral processing circuits tailored for recovery of the dominant copper minerals in each. After comminution to a target grind size of 80% passing 150 µm, each ore type is subjected to flotation to recover the copper sulphide minerals (chalcopyrite, bornite, chalcocite, covellite). The oxide float tails and a large proportion of the mixed float tails are then treated by atmospheric leaching to extract copper from the remaining copper-hosting minerals, which include cuprite, malachite, chrysocolla, and delafossite. Some native copper is recovered by flotation and some of it is recovered by leaching. A small portion of the combined concentrate from all circuits is subjected to high-pressure leaching and the rest is sent to the smelter. Sulphuric acid produced during smelting is used for the atmospheric leach."

Nov 1, 2018

By J. A. Kinnaird, B. J. Youlton, K. L. Youlton

Methods for treating and processing refractory gold ores are well established. However, what is less well understood is how the formation of the gold-bearing deposits affects gold processing and extraction. In order to evaluate the effect of ore genesis on gold extraction a number of South African gold deposits were studied. These included complex Pilgrim’s Rest samples as well as refractory Fairview, Barbrook, and Consolidated Murchison samples. We found the refractory nature of gold ores is controlled by a limited number of well-understood mineralogical factors. Solid solution gold is linked to low temperature and pressure conditions in fine-grained sedimentary lithologies, while reactive pyrrhotite can form from hydrothermal fluids associated with mafic magmatic rocks. These formational controls can be used to identify and avoid complex deposits at a desktop study phase, or address and reduce complications further along the pipeline using early mineralogical studies.

Jun 1, 2021

By N. Mutemeri, T. -L. Field, M. Chuma

The categorization of artisanal and small-scale mining has a significant impact on perception and understanding of the sector, particularly from a livelihood perspective. Several developing countries classify different types of artisanal and small-scale mining based on legal status. Given the nature such activities, the tragedy of the commons theory has been applied to understand the inevitable environmental, economic, sociocultural, safety, and health negative externalities – which are products of informality and illegality. Consequently, formalization is a panacea to sustainability. This article aims to offer a conceptual organization and foundational knowledge for characterization of artisanal and small-scale mining. It seeks to identify existing literature on the subject to avoid replication and acknowledge other scholars. Moreover, the article aims to place the study within the context of existing literature, establishing relationships with other studies and why the research is necessary. This paper pinpoints gaps left from other studies in so far as the characterization of artisanal and small-scale mining is concerned. Thus, reviewing literature abetted in finding similarities and differences on how artisanal and small-scale mining is defined from a scholarly and legal basis. The paper ascertains major claims made by earlier research on this topic, such as environmental impacts, the lack of adequate regulatory framework, and presents querying and probing questions lacking from other studies.

Jul 10, 2024

By V. N. Medvedev, A. M. Bryukhanov

Stationary mine air control equipment enables monitoring of CH4 concentration only in sensor locations. CMC-4 individual indicator built into a caplight has been developed in Ukraine, extending CH4 monitoring to manned job sites. Major technical characteristics of the indicator are demonstrated. It features two operation thresholds: 1st threshold 1.0 to 2.0% vol. 2nd threshold 1.5 to 2.5% vol. Basic absolute accuracy ± 0.2% Caplight battery is a common power supply for the lamp and CH4 indicator, providing at least 10 hours of the system non-stop operation. Average pre-failure life is at least 10,000 hrs. It features: an explosion proof design and intrinsically safe test circuit; a small-sized sensor as an integral part of the caplight; a hybrid microcircuit to facilitate functioning of methane monitoring unit. The CMC-4 indicator weight is the weight of the caplight itself and equals 2.4 kg. A two-threshold design makes possible to distinguish between methane sources: slow accumulation due to diffusion or sudden rushes due to a gas-dynamic event. CMC-4 indicators in addition to stationary equipment minimize the risk of CH4 explosion underground determined as a product of accident intensity by calculated time interval.

Jan 1, 2003

By J. C. M. De Souza

The Samarco pipeline, the longest in the world for iron ore slurry transportation, started operation in 1977 to transport concentrate from the Germano facilities, in the state of Minas Gerais, to the pelletizing plant, located 396 km away, in the state of Espirito Santo, on the south-east coast of Brazil. Designed for a nominal capacity of 12 million tons per year, the pipeline reached 15.5 million/year due to operational improvement and, in late 2005, it was resized to transport 16.5 million tons per year, with the installation of a booster station. In order to ensure the accurate performance of the system, a pipeline cleaning programme was carried out and, since it has been 29 years from the operation start-up, precise knowledge of the pipe condition would be fundamental to guarantee the success of the project. The cleaning programme demonstrated the potential of operational gains from this initiative, and its effect on the corrosion control and future measures, which should be permanently adopted to maintain the improved capacity. The intelligent pig runs provided essential data used to establish a pipeline integrity programme that allowed Samarco to develop a pipe repair plan based on the severity and significance of the features and to implement a future pipe replacement plan.

Jan 1, 2007

1. Book review . Australasian coal mining practice, edited by C.H. Martin. Reviewer: R.B. MacGilIivray This book is an extremely comprehensive coverage of coal-mining practice in Australasia, the countries covered being Australia, New Zealand,and Papua New Guinea. 2. From The Institute of Metals The folowing are available from The Institute of Metals, 1 Carlton House Terace, London SWl Y 5DB. Physical and elastic characterisation, edited by M. McLean. 1989. 228 pp. £25.00. High nitrogen steels, edited by J. Foct and A. Hendry. 1989. 461 pp. £49.50. Proceedings of the First International Calcium Treatment Symposium. 1988. 116 pp. £15. New cored-wire injection techniques, particularly as Design for recyc/ability, by Michael E. Henstock. 1988. 150 pp. £15. Solidification processing. 1988. 549 pp. £45. Marine engineering with copper-nickel. 1988. 103 pp. £18. Characterisation of High Temperature Materials. 3. New journal FMJ International Publications Lid have announced a new quarterly publication, Aluminium Today. 4. Other new publications Algorithms in real algebraic geometry, edited by Denis S. Arnon and Bruno Buchberger. London, Academic Press, 1988. 274 pp. £15.95. Proceedings, Foundry and Heat Treatment 88. R150 per set of 5 volumes, or R40 per volume.

Jan 1, 1989