Search Documents

Currently there exist several explosive quantity-distance (Q-D) rules variously exercised by most countries to protect personnel and property against the effects of accidental explosions. These regulations apply to manufacture, transport and storage of explosive products. This paper reviews the technical basis behind these regulations, as they apply to commercial and military explosives. The characteristics of a blast wave and missiles issuing out of an explosion site and their role in determining the level of damage to a target are discussed. The need for further research on the effect of detonation of charges of non-standard geometry, and under confined conditions such as tunnels is discussed. The challenge in estimating the net quantity of explosives involved and calculation of its TNT-equivalency is also highlighted.

Jan 1, 2011

By Sunil Vytla, Akash Adhikari, Purushotham Tukkaraja

Blasting operations produces gases and fumes that may be toxic or non-toxic in nature. A detonation of commercial explosives such as ANFO, emulsion, and dynamite would ideally produce only nontoxic products such as steam (H2O), carbon dioxide (CO2) and nitrogen (N2). However, in the real world, the detonation of explosives produces toxic products such as nitrogen dioxide (NO2), nitric oxide (NO) and carbon monoxide (CO). The focus of this study is the blast fumes entrapped in the muckpile. Fume clearance and workplace re-entry time studies performed in the past have overlooked the toxic gases entrapped in the muckpile. Studies show that as much as 60% to 70% of the fumes or gases produced during blasting underground can remain entrapped in the adjacent rock mass or in the muckpile. The toxic fumes trapped inside the muckpile are slowly released and could be fully uncovered during the mucking process. Exposure to these gases or fumes is hazardous to mine workers. In this study, author have analyzed the nature of fume flow, i.e. accurately predicting where and how the fumes flow after an underground development/tunnel blast. This will help in determining i) precise re-entry times for the workers ii) rate and direction of the fume flow. Computational Fluid Dynamics (CFD), a mathematical simulation technique that predicts fluid dynamics phenomena is used for this purpose. CFD is preferred over physical models because it is inexpensive, once the accuracy is established, a wide range of scenarios can be simulated quickly, and the toxic gas flow patterns through underground openings can be analyzed efficiently. For this study, CFD is performed using SC/Tetra software owned by MSC software company.

By Les Willan, Chris Batten, Matt Sparkes

In late 2008 Xstrata Newlands Coal Mine in Central Queensland and Orica Mining Services engaged in discussion to investigate methodologies to change their current mining practices and overcome the issues in the mining of steeply dipping coal seams, the associated coal loss risk and to assist in improving mining productivity. A strategy was developed and it was determined that through-seam blasting was essential to the success of winning the coal from the Wollombi Pit at Newlands.

Jan 1, 2010

By A. Andrades, E. Arias, Y. Pizarro, J. Alarcón

Division Ministro Hales - Codelco (DMH) is located at 2600 meters above sea level, 10 km north of the city of Calama, Antofagasta region, Chile. In operation since 2010, it corresponds to a porphyry copper deposit that is exploited by the open pit mining method. The ore is mainly composed of sulfides, which is concentrated by comminution processes such as crushing, SAG milling and ball milling to liberate the mineral particles, and then separated from the waste (concentrate) in flotation stages, including a concentrate regrinding stage. Reports from the DMH processing plant area have identified a decrease in fine copper recovery, with the first hypothesis being the high percentage of ultrafine particles (% <45µm) in the flotation feed. Due to the above, DMH & Orica decided to carry out activities to identify the controllable variables that can impact the generation of low size particles in ore and adjust them to reduce the percentage of fine material generation, with special focus on the Drilling and Blasting processes. Based on the data provided by DMH, we evaluated what could be integrated to make an analysis. The different attributes associated with the ore and their effect on copper recovery were evaluated. In parallel, at the mine, a fragmentation measurement campaign was carried out at the loading faces and granulometric analysis of the drill cuttings. Once the correlations between the attributes and copper recovery were identified, hypotheses were established and reviewed with the Drilling & Blasting, Geotechnical, Geology and Process Plant areas. With the validations of the hypotheses and the results of the in-mine (cutting) measurements, we proceeded to review the criteria for the classification of Blastable Geotechnical Units and their associated D&B designs. Using software and the Crush Zone Model (CZM) tool, which considers rock and rock mass parameters, scenarios for various D&B design proposals were simulated with the objective of reducing the generation of ultrafine particles from the blasting process. Next steps include trial blasting with the D&B design recommendations, which will require follow-up to the flotation process to identify the impact on the reduction of ultrafine material from blasting.

Jan 1, 2024

By Yogesh Narula

Nevis Bluff Landslide - On September 17” 2000, a rockfall measuring lO,OOOm3 at Nevis Bluff, New Zealand, triggered a loday emergency. It ended when a hazardous column of rock that towered over State Highway 6 was finally shattered. The operation called for unusual and unique solutions using aerial bombing and inverted blasting techniques, not known to have been attempted before under these conditions, anywhere in the world.

Jan 1, 2002

By D E. Shaw, J B. Case, J Gusek

Explosive casting of overburden is defined as the use of explosives in blasting to move overburden to a spoil pile without rehandling. Studies of the economic feasibility of the method, and the formulation of a design hypothesis involving rock properties, and blasthole geometry are presented. These studies indicate that if technical feasibility can be demonstrated to increase surface coal production, considerable economic advantage would accrue to coal mine operators.

Jan 1, 1980

By Michael Burrell

This project involved the protection of an historic landfill located on the site. Construction blasting was for a permanent access road to carry traffic to and from a new metal processing plant being constructed nearby. The landfill contained materials disposed of during the closure of a Phosphorus plant that had previously occupied a portion of this site.

Jan 1, 2012

By Tristan Worsey, Nathan Rouse, Evan Thibaud

Electronic detonators allow for variability and accuracy with blast delay selection and timing sequence. However, a single published guideline for selection of electronic timing delays is not available on the OneMine database. There are published documents that present options for timing with electronic detonators, some of which provide great detail and scientific evidence, but there is no single document that presents several different approaches with simple instructions on how to apply the various timing approaches. This paper reviews published electronic timing approaches and results, then presents guidelines for electronic timing for alternative mining methods, which include: bench blasting (ie. quarries) and crater blasting (ie. metals mines). Most of the approaches are based on calculating milliseconds per meter for rock types, as quantified by the rock sonic velocity. Guideline calculations are provided for recommended hole-to-hole delays and row-to-row delays for both free-faced bench blasting and crater blasting approaches. These are the two most common blasting methods for mining operations. Typically, free-faced bench blasting is the approach used in quarries with a bench height to burden ratio of around 4, and crater blasting is typically used in large blasthole diameter/short bench blasting in metals mines with a bench height to burden ratio of around 1. Mines may focus on fragmentation, mucking rates, ore movement distance and movement direction. Recommendations are also included to provide general recommendations based on a mine’s preference for movement and fragmentation. References include twelve studies on bench blasting and six studies on crater blasting. In addition, a discussion is included on the application of these recommendations at a full-scale surface gold mine.

Jan 21, 2025

By Glenn Tobin

The overarching goal in modern drill and blasting operations is that of optimising mining operations to achieve higher levels of productivity, safety, profitability and sustainability. Air decking, a technique used in drill & blasting to optimise explosive product use while achieving a target rock fragmentation1, is a technique that when executed correctly is proven to achieve consistent results independent of rock strength and the position of the holes (single, multiple, vertical, slanted), as well as being proven to reduce super-fragmentation (under-size or fines) while able to achieve optimal fragmentation, especially in the stemming zone2. The ‘shock absorber effect’ if the air deck reduces ground vibration and air blast3. Additionally, the practice of loading explosive product directly in saturated ground without dewatering or lining prior is an increasing global trend.

Jan 1, 2012

By D T. Froedge

This paper is a presentation of a coyote shot at the Oriskany Sand Quarry of the Pennsylvania Glass Sand Corporation, Berkeley Springs, West Virginia.

Jan 1, 1982

By Tony Francelj, D. Scott Scovira, Remi Proulx

The Meikle Mine is a high-grade, underground gold mine that utilizes a primary and secondary stoping method with delayed backfill. The newly developed Rodeo Mine will start production using similar mining methods in late 2001. The combined production for the mines will be 4100 stpd of ore in 2002. Dilution of the secondary stopes resulting from blast induced overbreak of the backfill placed in the primary stopes was an issue identified as being a major contributor to the total mining cost at the Meikle Mine. To address the overbreak issue, a low-density, polystyrene enhanced bulk emulsion was developed and introduced to the mine. The density and energy of the emulsion was varied until an optimal level was reached. The use of a low-density bulk emulsion has greatly reduced the overbreak of the primary stope backfill when blasting the secondary stopes. Benefits to the mines include reduced secondary stope dilution, lowered total mining cost, and increased revenues.1

Jan 1, 2002

By Douglas Rudenko PG, Jay Elkin, Siavash Mahvelati Ph. D.

Very little studies have investigated the behavior of cracks in unlined tunnels over long periods of time, especially when such flaws are subjected to blast-induced vibrations. Using a pool of 30+ blast events, a positive correlation was found between the peak particle velocity and peak crack movement.

Feb 1, 2020

By Claudio Lechuga, Carlos Scherpenisse, Juan Rafael Otaiza

From the analysis of drilling process, Block Model information, drilling pattern data and expected fragmentation targets; GBlast® software optimizes the explosive charge design in order to standardize the particle size of each blast.

Feb 1, 2020

By H. S. Venkatesh, G. Gopinath, R. Balachander, G. C. Naveen

Punatsangchu Hydroelectric Project Authority is constructing 1020 MW underground hydroelectric project in Bhutan. The project envisages construction of concrete dam, Desilting Chamber, Head Race Tunnel, Power House Complex and Tail Race Tunnel. Tunneling is one of the major activity in any underground projects as they are driven for multiple activities. By and large the tunnels are a major part of connecting networks from surface to caverns/underground working sites. Many tunnels in hydropower project are part of water conducting systems and one such important tunnel is the Tail Race Tunnel in this project and had to be excavated in thinly foliated rockmass conditions by D&B method.

Feb 1, 2020

By Dipankar Gorain, A K. Vishwakarma, Vivek K. Himanshu, Murari P. Roy, Shubham Singh, R S. Yadav

The industrial establishments of a power plant consist of many important structures viz. cooling tower, wagon tippler, track hopper, plants and offices. The leveled foundation is the utmost need for erecting these structures. The leveling of the foundation is done by rock excavation, when the establishments have to be setup in hilly/rocky areas. Drilling and blasting is the cheapest and most dominant method of rock excavation. However, this method has associated hazards in terms of blast induced ground vibration, air overpressure, flyrocks etc. The foundation work and erection of the industrial buildings are done in parallel to achieve the faster construction of the establishment. The challenges to reduce the induced hazards in such cases are more. This paper presents a case study on the controlled blasting method devised for the rock excavation for construction of 2 × 660 MW Obra-C thermal power plant. The foundation work for this power plant was made by excavation of Dolomitic rock. The excavation work was performed in the proximity of the existing residence of the local people and Obra market. With the advancement of project, the excavation was also performed in the proximity to the ongoing construction work of various industrial buildings. Accordingly, the controlled blasting pattern was devised suitable to the specific sites. The pattern consisted of variations in blasthole diameter, burden-spacing, maximum explosive charge per delay, total explosive in a blasting round, initiation system and direction of initiation. The suitable muffling arrangements were also used, when the blast was conducted in the close proximity to the structures. The initial blasting pattern was established by analysis of blast vibration wave propagation characteristics. Thereafter, the final pattern was adopted for the safe excavation at the site. The safe excavation for the foundation work of this power plant has been completed successfully based on the devised controlled blasting pattern.

Feb 6, 2023

By Santiago Gómez, Pablo Segarra, José A. Sanchidrián

In-hole detonation pressure measurements are unusual in the production environment of a mining operation, partly owing to the hostile conditions to which recording equipment and pertinent probes must be subjected and, partly by the constraints of the production cycle. In recent decades, detonation pressure measurement techniques have been developed using low carbon resistors (LCR)-based gauges. They are cheap, relatively easy-to-operate, robust and with a high percentage of success in both open-pit and underground mining. Detonation pressure measurements are extremely important when carrying out numerical modelling to simulate explosive induced vibrations, since simulation results are highly dependent on the pressure-time history applied on the blasthole wall. Analytical equations have typically been used to model the pressure-time history; however, they usually do not adequately represent the behaviour of the explosive in terms of: peak pressure reached, rise time, mean frequency, decay and shape of the signal. Experimental records may be directly used instead of utilizing synthetic signals if they are available. In this work, (LCR)-based gauges are used to measure detonation pressure inside a production blasthole. The operation principle of the gauges utilized and the instrumentation layout is described in detail. A flexible resolution USB oscilloscope with high sampling rate has been used to catch the elusive pressure peak event. Measurements were carried out in production blasts fired with ANFO (0.86 g/cm3) in an underground mine––this also includes velocity of detonation (VOD) records––. A procedure based on the shock impedance matching has been developed to calculate the detonation pressure due to the characteristics of the gauges prevent its direct measurement. Detonation pressures obtained range from 1.71 to 2.97 GPa (248.01 to 430.76 ksi) which are in line with pressures calculated from the VOD records. Mean frequency and rise time analysis shows that 2 of 3 signals cannot be described using typical analytical equations.

Feb 6, 2023

By Neal Lee

Often the effects of wet boreholes are not taken into consideration when designing a blasting program to exhibit a certain amount of explosive energy per unit of rock such as design by powder factor, expressed in lbs./bcy (pounds explosives per bank cubic yard) or kg/bcm (kilograms per cubic meter), often the effects of wet holes are not considered. This paper examines different methods of loading wet holes and the effects they have on actual explosive quantities/unit of rock. In particular, we are looking at the amount of water trapped within the explosive column (bulk loading from the collar), or the annular space left void of explosives product around and between cartridges (wet-bags) with many of the current wet hole loading methods in use. We will focus on the effect this has on actual powder factor relative to “as designed” dry hole loading values, as well as the effect on performance of the explosives.

Jan 1, 2011

By Andreas Bienz

The safety of persons from accidental explosions and fires during manufacture, storage, transport etc. of explosives, pyrotechnics, propellants, firework and ammunition is most commonly assessed according to prescriptive rule-based approach: Safety is given when all requirements which are listed in numerous regulations and directives (such as e.g. safety distances, limited quantities, protective installations etc.) are complied with. Such a deterministic prescriptive rule-based approach is quite easy to apply but has got disadvantages, however: The actual state of safety in a specific case is not explicitly and quantitatively expressed, and it is not distinguished between the endangered individuals and the whole group. As a result, the effects of the safety measures cannot be measured. This is why uneconomical and in the worst case useless safety precautions cannot be avoided. In addition, waivers are difficult to negotiate, meaningful and sound arguments for pro and con being lacking.

Jan 1, 2007

By Pierre De Pasquale, Gilles Jauffret, Ricardo Chavez

"When blasting in quarries or mines, the main source of inconsistent results is directly related to thenon-homogeneous energy distribution through the rock-mass volume. This variation has differentorigins: drilling deviations, geometry differences from one borehole to another (burden, spacing ...),and inherent geological conditions."

Jan 1, 2016

By Robert Lee, Pertti Paavola

Automated vibration monitoring and web-based data distribution has proven itself on the largest single construction project ever undertaken in Finland. The excavation for the Kamppi Center Project in the center of Helsinki was completed in November of 2003 and involved the removal of over 200,000 m3 (260,000 yd3) of rock and over 1,700 individual blasts. A system was installed, incorporating 37 discrete monitoring points located throughout an underlying metro station, and other surrounding underground and surface facilities. After every blast, vibration data was automatically transferred from the monitoring network to a server database. Stakeholders were able to access and review vibration reports on a password-protected website within 90 seconds of each blast. This allowed engineers to verify that recorded levels were in compliance with established limits, before proceeding with subsequent blasts. The data was also imported into a semi-automated Scaled Distance tool for analysis using linear regression techniques. This was used to determine, and adjust for trends in blast-induced vibration.Copyright

Jan 1, 2004