Search Documents

By Jessie L. Bonner, W. Stephen Blomberg, Mark Leidig, Heather Hooper

Understanding the effects of the bench on ground motion can improve the design of cast blasts and achieve improved blast efficiency while remaining below vibration requirements. A new dataset recorded in September 2003 from a coal mine in Arizona has allowed us to examine the excitation of short-period Rayleigh-type surface waves from four simultaneously-detonated explosions in and below a topographic bench of a mine. The explosions were recorded on a network of over 150 seismic sensors, providing an extensive understanding of the ground motion radiation patterns from these explosions. We detonated two separate explosions (~3 tons and ~1.5 tons ANFO) in the deepest pit of the mine, thus the explosions were shot to solid rock. Within 25 meters of these two explosions, we detonated two additional explosions of similar explosive yields in a bench, thus these explosions were shot to the free face. Radiation patterns and spectral ratios from the explosions show increased amplitudes (by a factor of 1.5 to 2) at azimuths behind the bench relative to the amplitudes in front of the bench. We compared these findings to seismic observations from two ~1.5 million pound cast blasts at the same mine and found similar radiation patterns. Modeling of these blasts shows that the variations in ground motion are caused by the topographic bench as a result of 1) horizontal spalling of the rock falling into the pit and 2) non- linear scattering near the free- face. We also note that shooting to a buffer (previously blasted rock) causes the azimuthal variations to be significantly reduced.

Jan 1, 2005

By Jackson R. Pressley, Bruce Vandenberg

The knowledge of how and when your explosives go off can help you make intelligent decisions regarding future application of explosives thus removing some of the black magic associated with blasting. The net result will be intelligently set-up shots with timing, explosive charges, and placement more accurately done. Lower operational costs can be achieved when the correct combinations are applied.

Jan 1, 1992

By Troy Williams, Chris Preston, Ian Lipchak

"Underground blasting operations are challenging from the standpoint of the distribution of explosivesenergy representative of ring blasting. Energy from both shock and pressure regimes of commercialexplosives may appear concentrated in the collar region of a typical ring blast and diluted at the toes of holes due to the oblique geometries of blastholes. The non-homogenous nature of ore in whichexplosives are distributed via drillholes, adds to the complexities of generating particulate profiles from fragmented material with consistencies that are predictable from blast pattern to blast pattern - well suited for specific underground handling equipment and mill processing. In an ideal world, it would be the blasting operations themselves that represent the primary crushing mechanism, or at least mitigate mechanical crushing that can comprise a large component of the cost in generating suitable muck. This paper presents a dynamic break view in 3D that allows a planner to visualize the potential break zone around a blasthole generated by an explosive load using a Kleine field. Simple as it sounds, this methodology provides information that can be used in conjunction with cavity monitoring surveys (CMS) to potentially judge dilution due to overbreak as well as recovery for a typical blast. As examples, there are two break geometries that are examined regarding circular breaks and elliptical breaks around blastholes. Using a Kleine field to define break, a planner generated isosurface can be generated and compared to CMS data for calibration and prediction, using AEGIS 3D ring design software."

Jan 1, 2016

By W. J. Birch, R. Farnfield

The use of electronic detonators to control blast vibrations has been previously established by many authors. This is performed by determining the optimum delay period between the blast holes for a particular pattern that can accurately control the firing frequency of the blast, which in turn has a direct bearing on the frequency composition of the ground vibrations recorded at a particular location. This was established by Pedgen, Birch, Hosein & Farnfield (2006) whereby like-for-like comparison tests between non-electric and electronic blasts were carried out in a limestone quarry in northern England. They demonstrated that resulting peak particle velocity values recorded at near and mid-field distances were primarily a product of the firing frequency of the electronically initiated blasts.

Jan 1, 2009

By Gordon Revey

The challenge of managing blasting risk, types of risk, public perception, and a system for managing risk were covered in the first part of this article in the May/June 2000 issue of the Journal of Explosives Engineering. This final part of this two-part series provides a method for identifying specific blasting risks and reviews the importance of community relations.

Jan 1, 2001

By Marcia Harris, Richard Mainiero, Michael Sapko

Since 1988, there have been 17 documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through ground strata into occupied enclosed spaces as a result of proximate trench blasting or surface mine blasting. These incidents resulted in 39 suspected or medically verified carbon monoxide poisonings and one fatality. To better understand the factors contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out studies in a 12-foot diameter sphere to identify key factors that may enhance the levels of CO associated with the detonation of several commercial trenching explosives. The gaseous detonation products from emulsions, a watergel, and ANFO blasting agents as well as gelatin dynamite, TNT, and Pentolite boosters were measured in an argon atmosphere and compared with those for the same explosives detonated in air. Test variables included explosive formulation, wrapper, aluminum addition, oxygen balance, and density. Major contributing factors to CO production, under these laboratory test conditions, are presented. The main finding is the high CO production associated with the lack of afterburning in an oxygen poor atmosphere. Fumes measurements are compared with the manufacturer’s reported IME fume class and with the Federal Relative Toxicity Standard 30 CFR Part 15 in order to gain an understanding of the relative toxicity of some explosives used in trench blasting.

Jan 1, 2003

By Ron Lutz

In today’s world, production is the name of the game. We are all in business to make money. In the Quarrying and Mining industry the same holds true. The primary goal is to develop the best drilling and blasting program available to maintain uniform fragmentation to maximize production. Also we want to maintain drilling and blasting costs and minimize escalators. This paper is intended to discuss ways for all parties (quarry’s, blast service and drill companies) to attain this through understanding what can be done to help blasthole drilling and production. Blast designs and seminar’s emphasize the accuracy of drilling to produce better fragmentation. Blast design must also include basic concepts in the drilling process. The type of drill to be used for example whether it is a crawler or truck mount, top hammer or down the hole is important. Quarry operators have a role to play as well. They hold the key to the production of drilling. What the customer does or does not do has a direct effect financially to the drilling. The phrase of pay me now or pay me latter comes to mind. This paper will explore the detail of planning that is required by the quarry and/or blast service companies before a single hole is drilled. The drill must be able to meet the production need of the operation. The type of drill available and what can and cannot be done. The drill cost must be competitive. This paper will touch on comparison drill costs from 1967 to 1999.

Jan 1, 2000

By Alastair Grogan

In October of 2002, the author was retained by Public Works and Government Services Canada, on behalf of the Department of National Defense, to design, construct and test the effectiveness of a bubble curtain system at an underwater demolition range, near Victoria, BC. The purpose of the bubble curtain was to reduce the potential for fish mortalities at the site. This paper presents some of the elements of the design, along with the results of overpressure monitoring during blasting and compares the results of fish mortality and animal behaviors with and without the bubble curtain in operation.

Jan 1, 2005

By Sam Kangwa, Thomson Sinkala

Th e re are three basic types of hole deviations in long hole d ri l l i n g , n a m e l y collar i n g , alignment and tr a j e c t o r y dev i a t i o n s . In mining, the accur a cy in drilling has a significant effect on the effi c a c y and economy of mining oper a t i o n s . This ar t i cl e d e s c ribes the types, s o u r ces and effects of hole deviations in mining oper a t i o n s . The art i cle further demonstrates the economic consequences due to hole dev i a t i o n s .

Jan 1, 2004

By Charles Pretorius, Henk Ludik

Navachab Mine experiences difficulties with pit wall stability in certain areas of the mine. The main reason for the instability is the fact that the geology comprises many joints and faults. Blasting, without impacting negatively on the stability of the pit walls, poses a major challenge.

Jan 1, 2006

By Jack Eloranta

This paper documents the relationship between material handling and processing coete compared to blasting cost. The old adage, "The cheapest crushing is done in the pit", appears accurate in this c!ase study. Comparison of the accumulated cost of: powder, selected wear materials and electricity; indicate a strong. inverse correlation with powder factor (lbe powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone.

Jan 1, 1995

A series of stemming confinement tests were conducted at a test site near Vernal, Utah. The purpose of the study was to determine the relative performance of various stemming enhancement “plugs”, stem types and loading configurations. The stemming performance was quantified in terms of: . Stem confinement time . Stem ejection velocity . Ground swell velocity . Ground vibration . Air blast . Crater formation Of primary interest was the performance of a new spherical stemming enhancement plug. The initial findings indicate that the hard plastic spheres improved blast performance when used appropriately. Their ability to improve blast performance is reduced when used in over confined or severely underconfined conditions. The study also evaluated the effects of air decking on stemming confinement and explosive performance.

Jan 1, 2000

By Edward Walter

Rock excavation for tunneling projects occurs on a regular basis in the Cleveland area. These tunnels are being constructed to increase the capacity of the sanitary sewer system. Controlled blasting must be performed to remove rock in a number of phases of the project. The rock excavation for construction of a junction chamber is just one case where blasting is the safest and most efficient method available.

Jan 1, 2001

By David Miller, James Santoro

Blasting is often required in urbanized areas to allow for economical execution of construction, demolition, and mining. Several examples of operations that require blasting in built up areas include: rock blasting for foundation and utility excavations; surface and underground mining for mineral extraction; and explosives demolition. Although explosives demolition is an engineering discipline, not at all like rock blasting, it still uses explosives for the felling of structures that have outlived their usefulness. Through the use of modem technology and implementation of extra safety precautions, explosives are used safely in congested areas to make the performance of critical work economical and feasible. This paper discusses several precautions required when undertaking various types of rock blasting and explosives demolition in congested areas. It also presents the adverse effects that must be considered when blasting in congested areas. The effects identified include flyrock, vibration and airblast, fumes, and non-elastic (permanent) ground deformations/overbreak. Measures for mitigating and controlling these adverse effects to provide on-site and public safety are presented.

Jan 1, 2000

By Michael Allen, Paul Worsey

In underground blasting, the pull of the initial cut is the limiting factor for the success of the rest of the round. By improving the pull of the first cut, a critical step is made towards improving the entire round. This project attempted to optimize a burn cut’s effective pull by varying the depths of the relief holes in the burn. The effect of varying the depths of the relief holes was investigated, including depths longer than that of the cut’s charged holes. The overall objective was to consistently achieve greater pull than in a standard burn, using an identical amount of explosives. Increased pull results in savings of both time and cost in underground heading advance.

Jan 1, 2015

By Francisco Sena Leite, Pedro Brito, Auã Kiahla, Raquel Carvalhinha, Tomi Kouvonen, Vinicius Miranda

Shockwaves that generate vibration in the surrounding environment of a blast, are one of the most important factors to control drill & blasting works near delicate buildings as well as in sensitive structures (wall control). On top of the damage to the buildings themselves, sensitive equipment such as computers, measurement apparatus and medical devices can be also compromised. The most commonly measured values from vibration are PPV (peak particle velocity), acceleration and displacement. Some devices and techniques have been developed in the last decades to measure the impacts of these vibratory phenomena. This information can be used to predict levels of vibration for future blasts and improve their quality of design using the attenuation law. From traditional studies to modern seismographs, a range of solutions are used for this propose. The main problem of applying this kind of technology is the high cost associated with each measurement device. In order to measure the ground vibration using new technologies while lowering the cost, a device has been developed using a microcontroller and electronic sensors commonly found on the market. This new equipment was tested side by side with traditional seismographs and the results were sent to a server for analysis. After several blasts, the necessary data was generated for the validation of the prototype. Through numerical mathematical processing (Taylor’s approach and numerical derivation) the original data supplied by the accelerometer’s sensors was transformed into velocity and, after the data mining, a statistics residue analysis was applied in order to evaluate if the data from the prototype and from the traditional seismographs were similar. The data from each system was used to estimate the attenuation law and the results are shown in this paper.

By Yasunori Kosaka, Junya Tokita, Aramaki Shosaku, Inoue Junji

Light ANFO that satisfies blasters and customers who want to reduce the amount of explosive consumption without changing blasting effects and designs and passes Cap sensitivity test regulated by law. The reduced loading density of light ANFO reduces the amount of explosive consumption. The loading density of conventional ANFO is 0.X-0.9g/ml, while the loading density of light ANFO is 0.7-OXgiml. The detonation velocity of light ANFO is maintained not to reduce blasting effects. Detonation velocity of conventional and light ANFO using steel tube of inside diameter 36 mm are 3200 - 37OOms. detonation velocities are the same though the loading density of light ANFO is reduced by O.lg/ml. This suggests that the reactivity of light ANFO improves.

Jan 1, 2002

By Randall M. Wheeler

The measurement and analysis of blast-induced ground vibrations are more complex than ever before. This is primarily due to the advancements made in microchip technology, mass storage utilities and the computer, which have allowed us to reduce and analyze data in a matter of moments instead of days. Terminologies such as Fourier transform, response spectra, cross-correlation, convolution, deconvolution and half-length frequency, etc. mean little to anyone except those who are experts in the field. A little understanding of the basic concepts behind vibration effects can help a beleaguered end-user feel more confident about what their measurements really mean.

Jan 1, 1992

By Ken Cross

This paper aims to demonstrate that explosives organizations and workers have a legal, moral and financial duty to be able to demonstrate their competence when required, and how that may be achieved at any level from explosives storekeeper to senior explosives engineer on a major project. The concept of competence is outlined, as are the benefits to members of staff, management and the organization, particularly in a regulatory regime that includes competence management as a key performance indicator.

Jan 1, 2013

By John A. Franklin, Tom C. Palangio, Norbert H. Maerz

WipFrag systems I and II have become the world standard in photoanalysis systems to measure fragmentation. Mines, quarries and excavating contractors can now easily measure blast results and track the progress of optimization efforts. This technology was developed and evolved to allow automatic measurements of the size distribution of patiicles on moving conveyors, in truck boxes and on crusher feeds. Production machinery can now be controlled by photoanalysis results and multiple cameras allow various locations to be monitored by a single system. Blast designs can be monitored on a shot by shot basis. Changes in delay times, explosives, patterns and hole sizes can be quickly evaluated. Along with this measurement capability has come a heightened awareness of the importance of “optimum size” and uniformity of particles for lowest cost production and material handling efficiency. In the past, savings in the “drill / blast” cycle of the operation were sometimes overshadowed by downstream production costs related to fragmentation. Now total production costs can be compared with fragmentation sizes which will immediately show the trend towards optimum size for economical production. No cost reduction program can be complete without this critical information.

Jan 1, 1997