Search Documents

By T. C. Alex, S Srikanth, Premchand

It has been suggested that reduction of the iron and manganese phases as far as FeO and MnO is preferred for the complete liberation and selective reduction of the copper, nickel and cobalt oxides in manganese nodules. The oxygen partial pressure/temperature regime suitable for this purpose has been delineated. Free-energy minimisation and thermogravimetric results indicate that the requisite conditions can be achieved if more than 10% of neutral oil is used at temperatures greater than 923 degrees C. Neutral oil content, temperature and roasting time have been optimised to maximise leaching recoveries of Cu, Ni and Co: up to 96% of Cu and Ni and up to 85% of Co can be recovered if 15% of neutral oil is used as a reductant at 973 K for 90 min

Jun 21, 1905

By T. Ogasawara, J. P. Barbosa, A. J. Monhemius, F. T. Da Silvia

A thermodynamic analysis of the sulphation of rare-earth phosphates and the water-leaching of rare-earth sulphates was used to guide experimental work on the sulphation and leaching of concentrates from Pitinga. It was concluded that the sulphuric acid digestion of xenotime is technically feasible and could be used industrially to produce yttrium and other rare-earth oxides. Yttrium extractions of more than 90% were obtained by digestion at 503 K for 4 h at an acid:concentrate ratio of 2:1 with particle size -0.053 mm. The apparent activation energy at temperatures less than 473 K, as determined from the Arrhenius plot, was 11.0 kJ/mol, indicating that the reaction is controlled by the diffusion of the reactants or products through the sulphate layer

Jun 19, 1905

By P. A. Rossouw, G. A. Fourie

Several attempts have been made over the latter half of the twentieth century to devise a system for the classification of underground mining methods. None of these are found to be totally successful. A revised classification is suggested with three main categories being identified by reference to fill requirements, steep stopes and stratified geological environments. Methods always needing lasting mass or structure fill include methods with timber-structured stopes and those with mass-filled (or cut-and-fill) stopes. Methods associated with steep stopes are subdivided into steep-stope-specific caving and steep-stope-specific non-caving (or self-supporting) methods. Methods not in the first two categories, often used in stratified geological situations, are not necessarily restricted to stratified environments and include caving as well as non-caving varieties. This category is further divided into room-and-pillar mining, longwall and shortwall coal mining and the type of open stoping found in gold or platinum reefs comprising overhand, underhand and breast-stoping variations

Dec 1, 1996

By P. H. Morris

To achieve the full potential of sub-aerial co-disposal the properties of the co-disposed wastes must be known and understood. A description is given of the morphology and properties of waste deposits that were formed during 19 field trials of sub-aerial co-disposal at the dual Goonyella-Riverside mine in Queensland and at Hunter Valley No.1 and Warkworth mines in New South Wales

Jun 19, 1905

By B. Tiryaki, O. Z. Hekimoglu

Shearer drums are a critical component in the overall performance of coal shearers, with the cutting performance depending very much on the disposition of cutter tools on the drums (the tool-lacing arrangement). A series of practical and theoretical studies has been undertaken to investigate aspects of shearer drum vibration in terms of circumferential pick spacing. A number of commercially available drums were redesigned and the lacing patterns compared with those of the original drums under near-uniform conditions. Mine trials were carried out at the Middle Anatolian lignite mine in Turkey with drums fitted on Eickhoff type EDW-230 double-ranging drum shearers. It was found that the performance of drums could be improved if the concept of circumferential pick spacing was taken into account in CAD packages along with the existing design parameters such as cutting rate, reduced dust, low pick consumption and low down-time

Jun 19, 1905

By C. A. Jeffrey

The Dirtlow Rake vein deposit, which is up to 12 m thick, contains a range of paragenetically linked replacement mineralisation styles typical of many Mississippi Valley-type deposit environments. The main ore zone lies within the solution collapse breccia domes, the more southerly of which has recently been well exposed, allowing its relationship to the associated mineral-hosting structures to be studied. The domes were largely formed during early silicification, propagated by dissolution collapse and infilled by subsequent fluorite-barite mineralisation. The location of pipes and pervasive replacement was also controlled by early silicification. Structurally controlled bow tie shears were formed as a result of fluid access at fracture-bedding plane intersections. The nature and distribution of the mineralisation styles indicate that the degree of fluid access, residence time of solutions in contact with the wallrock and susceptibility of the limestone to silicification each played a major role in dictating mineralisation

Jun 19, 1905

By R. A. Lord, H. M. Prichard

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The complex exemplifies a class of olivine-rich, platiniferous ophiolite complexes generated by unusually high degrees of hydrous melting above a subduction zone. Crystallisation of abundant olivine from unusually picritic magmas produced an exceptionally thick sequence of crustal dunite cumulates. Significant (1-4 ppm) concentrations of Pt+Pd occur where sulphide-bearing dunites are spatially associated with podiform chromite concentrations. In the area north of the Balta Sound, the chromitites appear to lie in distinct stratigraphic zones. A detailed programme of lithogeochemical and soil-rock interface geochemical exploration led to the intersection by diamond drilling of three stratiform horizons of sulphide-bearing dunites and associated precious-metal mineralisation. Patterns of cryptic geochemical layering, at scales from 200 m to less than 1 cm, suggests open-system fractionation

Jun 19, 1905

By I. J. Brown

Paper prepared for presentation at Industrial minerals and the environment, held in Leeds, 24-35 September 1990. The need to submit an environmental statement (EIS) has certainly increased the workload of those concerned with both its production and assessment. However, there is now good evidence that the system is enhancing public confidence in the minerals industry in particular and improving relationships between the developer, planning authority and those consulted such as statutory bodies, parish councils, civic societies, nature conservation interests and ramblers

Jan 1, 1991

By G. Kill

Although other energy commodities have developed successful futures contracts, long-term contracts still dominate the coal market. To establish whether coal markets will develop in the same way, coal price and volume data are tested against a set of criteria considered to represent some of the factors contributing to the development of a successful futures contract. Coal meets only some of the criteria: market players are subject to little risk in quite a stable market, have strong preferences for the specific nature of long-term contracts and profit from product uniqueness, each trade being individually negotiated. Potential structural changes in the western European market are not felt to be sufficient to create demand for a coal futures contract, but an empirical model has been developed that could form the basis of a further study to predict the potential for success

Aug 1, 1994

By B. M. England, M. V. Swain, N. Bristow, R. D. Dukino

The toughness and fracture mechanisms of ores with significantly different microstructures from Yandi, Koolan and Mount Whaleback were studied with a view to understanding their degradation behaviour. Bulk fracture toughness was determined by the 3-point single-edge notch beam test and the results interpreted using Weibull statistical analysis; indentation fracture mechanics was also used to measure fracture toughness of the different mineral forms and to understand their response to contact fracture

Apr 1, 1995

By S. P. Singh

The purpose of the cut is to provide a free face to which the remainder of a development or breasting round can break. The results of field testing in drifts and at a quarry face were used as a basis for a description of the rock breakage and flushing mechanism in the cut. It was concluded that the important features of a cut design are proper hole spacing, sufficient relief volume, drilling accuracy and relief holes slightly longer than the planned length of the round. The void space provided by the relief holes should be about 15% of the cut volume, with more required in weak, highly fissured rocks. The importance of drilling accuracy increases with round length, an error being magnified by the small blasthole spacing. The first hole pulls only about 20% of the round length, 4-6 holes having to be fired before the cut is pulled close to its design depth. The first four blastholes should be fired with a minimum inter-hole delay of 100 ms to provide progressive relief of burden and avoid the superimposition of ground vibrations. The earliest-firing charge should be closest to the relief area and act laterally, while the first of the vertically-fired charges to be detonated should be the uppermost. Problems during cut-pulling include sympathetic detonation, dynamic pressure desensitisation, charge disruption and freezing of the cut

Dec 1, 1995

By A. C. Apling, N. B. Barrett

Roadstone production requires the generation of non-flaky material, as outlined in British Standard 812 section 105.1; with respect to this criterion, a mathematical model of a cone crusher must be able to predict the flakiness index of a particular size range as determined by the relationship between thickness and nominal size. The Whiten cone crusher model utilises breakage and classification functions to predict a product particle size distribution only, so a shape function has been proposed that is based on a phenomenological approach, taking into account the transfer between flaky and non-flaky material at each stage of breakage. The results of laboratory tests to determine material breakage characteristics and of examination of pilot-scale test products illustrate the method's potential

Apr 1, 1995

By S Colak, M Tunc, C Celik, M. M. Kocakerim

The most important parameters affecting the solubility of ulexite (sodium calcium borate) in H2SO4 were found to be reaction temperature and solid:liquid ratio, in that order. Dissolution increased with increase in temperature and stirring speed and with decrease in solid:liquid ratio, particle size and acid concentration, the last effect as a result of decreased precipitation of CaSO4 on unreacted particles. Optimum conditions, in which around 99.5% of the ulexite could be dissolved, were a reaction temperature of 60 degrees C, a solid:liquid ratio of 1:8 g/ml, an acid concentration of 8 mol/l, particle size smaller than 425 micrometres, a stirring speed of 52.33/s, a reaction time of 1 800 s, a calcining time of 3 600 s and a calcining temperature of 170 degrees C. These conditions, determined by the Taguchi method, are reproducible in a commercial production environment

Jun 21, 1905

By G. M. Zhao

The gasification of lump coke with CO2 was studied in a fixed-bed reactor. The effective diffusivity of the gas was evaluated from measurements of the reactivity of the lump coke, produced by BHP Steel in New South Wales, and from kinetic parameters that were determined from the reactivity of fine grains. The grain model of effective diffusion in porous media was adopted to express the gasification rate of the lump coke and was found to fit the experimental data well. The relationship between reactivity and textural characteristics of the coke was examined

Jun 18, 1905

By J. S. Coats, G. E. Patts, N. Hughes

Conventional sampling methods are known to suffer from the variable loss of fine gold by elutriation. Freeze sampling yields representative and quantitative data that, when combined with information on the sedimentology of gravel-bed rivers, may facilitate the development of improved dispersion models for source detection. It is suggested that freeze sampling may have particular application to the orientation stage of a large gold exploration survey

Jan 1, 1991

By A. L. Grabovski

The potential of eccentric cone crushers for fine crushing has been improved by increasing the swing frequency of the moving cone, balancing the crusher, ensuring uniform feed via a rotating funnel with sideways discharge, introducing hyperbolic motion and employing the inertia crushing method, but further improvements to the specifications of existing cone crusher designs are limited by the rigidity of their kinematic coupling. A new design has been developed which combines two crushing modes, stone on liner and stone on stone, each with its own advantages. The main aims are to produce finer materials and to reduce liner weight. The benefits include an increase of more than 10% in the output of fine particles, improved protection of the liner against wear, as a result of filling of the cavities by material being crushed, and the use of almost 20% less material in casting of the liner. The chamber can be used in place of the usual liners of fine cone crushers

Jun 21, 1905

By A. S. W. Kurny, M. Z. Huq

Bangladesh ilmenite is partially altered, containing pseudorutile, rutile and haematite as well as the predominant ilmenite phase. A typical analysis is 39.45% TiO2, 24.19% FeO and 33.0% Fe2O3. Reduction of the ilmenite by charcoal was found to involve two major reactions: conversion of pseudorutile into ilmenite and rutile, and change of ilmenite into metallic iron and rutile. The first, which was much the faster reaction, was responsible for an initial increase in ilmenite content with reduction time at lower temperatures. Apart from these two major reactions, rutile was reduced to lower oxides at 1 100 degrees C with a consequent decrease in its XRD peak height

Jun 19, 1905

By I. Marklund, W. Hustrulid

Sublevel caving is likely to remain the dominant system at both Malmberget and Kiruna for the foreseeable future. The sub-level interval has increased from 12 m in 1983 to 30 m, requiring more effective drifting and the development of a contour blasting technique to reduce requirements for rock reinforcement. Production drilling is mainly by hydraulic hammers or water-powered in-the-hole machines drilling 115 m diameter holes. Loading operations are undertaken 7 days/week with 15-25 tonne capacity electric shovels. Production has increased by nearly 70% since 1983 and productivity has risen threefold

Dec 1, 1995

A production drill rig at a site in Sweden was equipped with a monitoring system to estimate production statistics. Drill running times, drill hole depths, penetration rate, rotation speed, thrust, air percussive pressure and torque pressure were recorded for every 10 mm of hole length for a period of 5 months. Operational activities (rock penetration, tube handling, moving and set-up time) accounted for almost 62% of the time consumed, the remaining 38% being different types of stoppage. Drilling itself, as opposed to handling, took less than 24% of the total time. The results give an indication of how the overall drilling capacity can be increased and which activity should be emphasised. The impacts of automation, new developments and reorganisation on production can also be predicted. Average production was found to be around 100 m/day, but varied between 50 and 160 m/d. The company's specification for the drill rig, before purchase, was that an average production rate of 130 m/d be attained over two consecutive months of drilling - a rate which monitoring shows will not be achieved

Jun 19, 1905

By D. C. Kaliampakos, A. K. Moutsatsou, J. K. Skotaras

The wastes from marble extraction in the Thasos- Kavalla-Drama region of northeastern Greece could be utilised as a new source of high-quality white carbonate fillers for the European market. Large deposits, satisfactory properties, acceptable processing costs and environmental benefits are among the factors that would have a positive bearing on a proposal for their use in this way. DTH, the waste arising from dolomitic marble quarrying operations on the island of Thasos, appears to be the more suitable material than DA waste from Nikissiani on the mainland because of the lower cost of primary grinding and the higher production rate of ultrafines with a mean particle size of 5 micrometres (the optimum size for filler properties in the case of both DTH and DA), its superior whiteness, the benefits that such use would bring to a very severe and complex environmental problem and the lower transport cost

Jun 18, 1905