Search Documents

By Olga D. Khmelnitskaya

The paper presents the results of research on the development of gold recovery technology from oxidized gold-copper ore of one of deposits in Russian Federation. Gold and copper grades in the ore are 9.5 g/t and 0.4%, respectively. Various options of flowsheets, such as direct cyanidation, thiourea leaching, flotation and gravity concentration followed by subsequent cyanidation of con-centration products, were tested. It was established that gravity-cyanidation technology with filtra-tion leaching tails and the use of solutions in the recirculation is the optimal option for ore treatment. The proposed flowsheet provides gold recovery for 91.0% at NaCN consumption 2.5 kg/t ac-cording to the results of pilot testing. Ammonia-cyanide gold leaching was also examined. In comparison with cyanidation, gold leaching solution in system NaCN-NH4OH-(NH4)2CO3 allows NaCN consumption to be reduced three times from 4.5 kg to 1.5 kg per 1 ton of the ore and provides the same gold recovery. Based on the laboratory and pilot plant tests results of gravity-cyanidation technology of gold dissolution, process design criteria were developed.

Jan 1, 2014

By Valentine Chanturiya, Irina Khabarova, Maria Ryazantseva, Igor Bunin

"XPS investigations of the influence of HPEMP - treatment duration on the surface composition for natural chalcopyrite and sphalerite are described. HPEMP is a video pulse with a nanosecond front lasting between 5 and 10 ns. The electrical field component can reach 30 kV, whereas pulses repetition frequency is 100 Hz. In general, the formation of metal-deficient surfaces, polysulphides or elemental sulphur and oxides/hydroxides, were determined during the treatment for both sulphides as well as the essential differences of the way of mineral surface transformation during the treatment. The chalcopyrite surface shows the formation of elemental sulphur under the HPEMP treatment at 103 pulses while appearance of unstable sulphite species was detected at the chalcopyrite surface within 5 seconds (0.5•103 pulses) under the same treatment conditions. The results indicate that the quantity of adsorbed water (at.%) is changed considerably during the HPEM - treatment depending on treatment duration for both minerals. The concentration of water onto the chalcopyrite surface decreased during 30 seconds (3•103 pulses) of the HPEMP - treatment and it rose after the treatment at 5•103 pulses. The inverse dependency was obtained for sphalerite surface. Single mineral flotation tests have shown the significant increasing of the minerals recovery."

Jan 1, 2014

By G. Demi, G. Belardi, N. Shehu, S. Cico

The physico-chemical interaction between minerals such as olivine, chromite and serpentine and the ions most commonly present in solution, like Ca and Mg and flotation reagents such as EDTA and oleic acid was investigated. The study was conducted via release tests, electrophoretic measurements and microflotation of selected minerals coming from the Kukes deposit (Albania). The results were confirmed by means of beneficiation tests on various types of ores, from the Kukes (Kalimash), from Bulquiza area and from the Rizo deposit (Greece). It has been demonstrated that when Na-K Oleate is used as collector chromite, olivine and serpentine can be separated at pH = 2.5 and/or 5.5 employing EDTA (EthyleneDiamineTetraAcetate) on previously deslimed material. This approach ensures flotation concentrates with a Cr2O3 content about 50%, at a recovery in excess of 65%.

Jan 1, 2003

By Isaak I. Maksimov, Tatyana E. Koltunova, Mikhail F. Yemelyanov, Liudmila A. Otrozhdyonnova

"INTRODUCTIONMetals losses amount up to 50% in coarse fractions in (>100 µm) and composite particles, and to 20- 25% in fine fractions (<10 µm) at non-ferrous floatation concentrating plants of the CIS. Therefore, reduction of metals losses in difficult fractions is of high significance.IMPROVEMENT OF FLOATABILITY OF COARSE AND COMPOSITE PARTICLESReagent regimes with application of strong collectors – xanthates ?5-?8, combination of butyl xanthates and aerofloats ?10-?12, butyl xanthates with hydrocarbons are proposed for this purpose. Application of such reagent regimes for copper and copper-molybdenum ores permitted to increase copper and molybdenum recovery by 0.5-3.9%.Studies, performed by means of specially designed non-frothing flotation machine with independently controlled agitation intensity and narrow size-ranges of air bubbles, established that the best results are achieved with employment of bubbles of 0.5-0.8 mm size regarding particles of any size, with small amounts of up to 2 mm size “transport” bubbles to be expediently used for floatation of coarse particles.Energy dissipation in the main volume of floatation cells must be lower than 0.2-0.25 m2/s3.Performed experiments permitted to formulate requirements to development of machine for floatation of coarse and composite particles. Such floatation machine with volume of 8.5 m3 provided for weak agitation in the main volume of floatation cell and uniform distribution of coarse particles throughout the depth owing to establishing of pulp circulation with upward flows. In addition, in the upper part of floatation cell where agitation is considerably weaker, favorable conditions are created for attachment of particles to bubbles. Testing of this floatation machine demonstrated a 7.5% increase in recovery of +0.2 mm particles in pyrite floatation and a 12-14% increase in recovery of +0.2 mm particles in apatite floatation as compared with a reference floatation machine."

Jan 1, 2003

By Aziza A. Yousef, Suzan S. Ibrahim, Mahmoud A. Arafa, Mohamed A. Abdel Khalek

Due to the shortage of fresh water in the Middle East, seawater has been used as an alternative in flotation beneficiation. The flotation process requires about 7 m3 of water/mt ore. This article aims to study the effect of seawater cations and anions on the flotation. Natural pure francolite, calcite, dolomite and quartz were characterized by chemical, thermal and x-ray diffraction analyses, surface area, solubility and zeta potential. Synthetic seawater was prepared with the major chemical composition similar to natural seawater as follow; 2.45% NaCl, 0.52% MgCl2, 0.41% Na2SO4, 0.116% CaCl2 and 0.07% KCl. Also, natural seawater was used in application. The point zero of charge was estimated at pH 6.5, 7.8, 9.2 and 2.2 for francolite, calcite, dolomite and quartz, respectively. Calcium ions were released from the three minerals with Mg2+ and P2O5 3– released from dolomite and phosphate, respectively. The adsorption of collector, zeta-potential and floatability of pure minerals were studied. The effect of individual cations and anions predominant in seawater are studied on individual mineral or group. The troublesome Ca2+ and Mg2+ ions should be controlled by soda ash addition. Sodium silicate improved the selectivity of mineral mixtures and natural ore. At optimum conditions the calcareous phosphate ore yielded a concentrate of 34% P2O5, at 83% recovery with 0.61% MgO, from an ore assaying 25.3% P2O5 and 9.4% MgO. To minimize the Clcontent, fresh water of about 0.5 m3 /t was used and the Cl- decreased to about 0.09 %

Jan 1, 2003

By S. J. Ma

With the very effective depressant and collector developed by China Bluestar Lehigh Engineering Corp (hereinafter referred to as LEHIGH), satisfied results are obtained from laboratorial beneficiation tests on phosphate samples from Karatau, Republic of Kazakhstan by the direct flotation process. In this paper the effect of single factors on performance of flotation is studied and their applicable ranges are proposed. The final test results are described as follows: As the feed contains 23.20 % P2O5, and 3.96% MgO, a phosphate concentrate assaying 29.77%P2O5 and 1.54% MgO is produced, and the P2O5 recovery in concentrate is 88.28%. The beneficiation tests make it possible to simplify existing technology with fine grinding-desliming, followed by reverse & direct flotation system and consequently improve the concentrate grade and recovery for the future beneficiation plant

Jan 1, 2014

By G. Voiloshnikov, A. Bogudlova

"The deleterious effect of carbonaceous matter during cyanidation of gold ores (so called preg-robbing) has been recognized for many years. Based on this, a new method using flotation to reduce the content of carbonaceous matter was developed. Low-sulfide gold-bearing ore with carbonaceous matter of 0.14% from a Russian deposit was processed. The purpose of these tests was to compare two flow sheet options. Option I comprised removal of carbonaceous product prior to sulfide flotation. Option II comprised removal of carbonaceous matter from flotation concentrate. It was found that the content of carbonaceous material can be reduced in sulfide gold-bearing concentrate prior to leaching. High gold recovery was observed during the separation of carbonaceous material prior to sulfide flotation using Option I. Due to lower reagent consumption the costs for reagents were decreased using Option II. The results have shown the effectiveness of a new method. Patent No. 2783808 was obtained for removal of carbonaceous material prior to sulfide flotation. This information will be used to design a large processing plant flow sheet in Russia."

Jan 1, 2014

By Mahdi Shevrini, Hamed Haghi

"In this research, the operation of screen classifying in silica processing circuits was investigated and modified by replacement of available trommel screens with teetered bed separator (TBS). In addition the effect of the mentioned replacement and addition of attrition scrubber on quality of final product, impurities removal, recovery and production rate were inspected. Considering screen efficiency problems to achieve certain particle size distribution, hydraulic classifying system was selected instead of trommel screens. Application of suggested plan improved quality and particle size distribution of produced silica significantly. Optimization of size classification in process circuit resulted in increase in production rate up to 21% (from 67% to 81%), silica recovery (from 68.35% up to 83.11%) and relative enhancement in removal of impurities such as Fe2O3 and TiO2. After optimization and stabilization of grinding and size classification section, industrial attrition scrubbing tests were carried out and the best solid percent and retention time were determined i.e. 70% and 6 minutes, respectively. Using sodium carbonate during attrition scrubbing, has major effect on removal of surface coating and staining especially sharp increase in clay removal; therefore 2 kg/t of sodium carbonate can be optimistic point of industrial procedure for this silica processing plant. It should be mentioned that application of attrition scrubbing which is followed by screw classifier for de-sliming were useful for better cumulating of particles in the range of appropriate liberation degree (+106-300µm) and efficient removal of metallic (iron and titanium oxides) and non-metallic (clays and feldspars) impurities."

Jan 1, 2014

By Kunihiko Yamaguchi, Gjergj Dodbiba, Toyohisa Fujita

Usually magnetic separation is performed to separate ferromagnetic, paramagnetic and diamagnetic particles by controlling magnetic field strength. In this research the wet high gradient magnetic separation at various kinds of magnetization of medium has been investigated to separate different kinds of magnetization of paramagnetic mineral particles from each other. Most of week paramagnetic particles are captured at high magnetic field using superconducting magnet. If the magnetization of fluid is larger than that of paramagnetic particle, the paramagnetic particle cannot be captured in the direction of magnetic field. The paramagnetic particles of different magnetization such as hematite, chromium oxide, perovskite and rutile are separated in different magnetization of fluids. These particles are present in the incinerated bottom ash. The separation is useful to recover titanium oxide from bottom ash and the removal of chromium of bottom ash is important to reuse the bottom ash as cement. The used fluids are paramagnetic liquids dissolving paramagnetic salts and the water based magnetic fluid dispersing the stable ultrafine magnetite. The dispersion condition of particles related to zeta-potential of the suspension feed is also important to separate effectively by controlling pH

Jan 1, 2014

By Marco Le Roux, Quentin Campbell

"Most coal supply contracts include strict limitations on the moisture content of the products. This limitation exists because of calorific, transport cost, and handling reasons. Managing the retention time on product stockpiles to facilitate drainage commonly controls the moisture content in coarser coal products. A large-scale pilot rig has been commissioned to facilitate research in this regard. A stockpile of about 15 tonnes of a typical washed power station feed coal from the South African Witbank coalfield was loaded onto a 6 x 6 m platform on load cells. The platform was shielded from the elements, like rain and wind, and an artificial rain sprinkler system was installed. A variety of rainfall intensities and durations were simulated and the water accumulation and run-off was measured. The material was also sampled for moisture and particle size before and after the series of tests. At the same time, the drainage characteristics of the same coal were determined in smaller scale drainage columns for comparison. Data is presented in this paper on the drainage rates, maximum accumulated moisture, final moisture, and the effect of evaporation. The results showed that for all rainfall patterns tested, drainage ceased after 2 - 3 days, but evaporation continued for at least the time period under investigation, albeit at a low rate. Evaporation contributed to dewatering at rates that depended on wind, temperature and humidity conditions. This caused a slow reduction in moisture content even after the run-off had ceased. The value of the final moisture depended on the coal PSD. It was also found that the intensity and duration of the more intense rainfall events did not significantly affect the maximum water accumulation, with drainage rates equaling the corresponding water addition rates which suggested that water ran off over the surface of the stockpile with limited penetration. During more intense rainfall scenarios, some penetration was apparent."

Jan 1, 2014

By John Ralston, Jona Addai-Mensah, Patience Mpofu

The flocculation and dewatering behaviour of kaolinite (non swelling) and smectite (swelling) clay dispersions has been investigated using hydrolysable metal ions Mn(II) and Ca(II) and anionic polyacrylamide-acrylate copolymer (PAM) at pH 7.5 and 10.5. A pH-dependent, specific metal ion adsorption behaviour, accompanied by a marked reduction in particle zeta potential and slurry shear yield stress, was observed to have a profound influence on the colloid stability of both types of clays. Due to the differences in the cation exchange capacity, the smectite clay dispersion required a higher amount of metal ions than kaolinite dispersion to produce similar effects. The adsorption density of the anionic PAM at the negatively charged clay particle surfaces correlated well with metal ion hydrolysis and adsorption behaviour, all of which had a strong effect on slurry settling rate and extent of consolidation. At pH 7.5 where Mn(II) ions hydrolyse, metal ion and flocculant adsorption densities were both greater in the presence of Mn(II) than Ca(II) ions. At pH 10.5, however, where Ca(II) ions begins to hydrolyse, higher adsorption densities were observed for Ca(II) ions in comparison with Mn(II) ions, as the latter hydrolysed completely and precipitated. The metal ion mediated flocculant adsorption led to improved hydrogen bond driven particle bridging and facilitated charge neutralisation flocculation mechanisms which significantly enhanced the dewaterability of both clay dispersions.

Jan 1, 2003

By Steven Bradshaw, Edson Charikinya

The application of high power microwave energy to secondary crusher products has been shown to induce micro fractures and cracks in the ore. This suggests that heap leaching could benefit from microwave-induced fractures, as the extent and kinetics of heap leaching processes depend on the accessibility of grains to lixiviants, which can potentially be improved through microwave treatment. The density and pattern of microwave induced cracks and how these cracks subsequently affect heap leaching recovery has not yet been investigated. The objective of this study was to apply X-ray micro computed tomography (X-ray CT) to investigate microwave induced cracks in large cone and HPGR crushed sphalerite particles within 3D space. The ore particles were microwave treated in a single mode microwave applicator coupled to a switched mode power supply and a water cooled microwave transmission sub system operating at 2.45 GHz. The ore particles were treated at specific absorbed microwave heating energies of between 2 and 3kWh/t by treating at 6 kW of forward power for treatment times of 1 s. X-ray tomography analysis was conducted on fine (-5+4.75) mm, medium (-16+9.5) mm, and large (-25+19) mm sphalerite particles before and after microwave treatment at voxel resolutions of 5 µm, 15 µm and 25 µm respectively. Image segmentation, thresholding and spatial registration techniques were used to study crack patterns in 3D images of HPGR and cone crushed particles. Analysis of the X-ray CT images after microwave treatment shows considerable micro crack formation within the Cone and HPGR crushed particles. The cracks pattern showed interphase cracks propagating across all phases, with no evidence of preferential cracking. A greater density of microwave induced cracks was observed on fine (-5+4.75) mm particles compared to the medium (-16+9.5) mm and (-25+19) mm large particles. The results showed overall increased particle porosity following microwave treatment.

Jan 1, 2014

By B. McFadzean, P. E. Ngoepe, P. P. Mkhonto, J. Taguta

The adsorption of heterocyclic collectors such 2-mercaptobenzothiazole (MBT), 2-mercaptobenzoxazole (MBO), 2-mercaptobenzimidazole (MBI) and their derivatives on pyrite form a basis in understanding the flotation reactivity that may be applicable in a wide range of sulphide minerals. This study uses a computational and experimental approach to determine the heat of adsorption of MBT, MBO, MBI and modified MBT collectors onto pyrite surfaces. Computational calculations found that the adsorption energies were in the order: MBO > MBI > MBT. The heterocyclic collectors were adsorbed in their thiolate form on the surface. In the case of the pyrite (100) surface, the MBT adsorbed through the exocyclic sulphur atom, while MBO and MBI adsorbed through the exocyclic sulphur and N atoms onto the 5-coordinated Fe atom. The (111) surface was found to be more reactive and different adsorption mechanisms were predicted, where the MBT exocyclic sulphur atom bridged on the 5- coordinated Fe and surface 2-coordinated sulphur atoms, while the N atom adsorbed on the 5-coordinated Fe atom. In the case of MBO and MBI, dissociation of the exocyclic sulphur atom from the collector occurred with subsequent interaction with the surface 5-cordinated Fe and 2-coordinated S atoms. This resulted in the collector carbon atom adsorbing on the surface 2-coordinated S atom, while the N atom adsorbed on the 5-coordinated Fe atom. The adsorption of the modified MBT was found to be more exothermic than the MBT, which showed that introduction of a –CS2 group on the exocyclic sulphur atom improved the affinity of MBT on the surface, and was thus a better flotation collector. The computational results were supported by experimental enthalpy of adsorption measurements and microflotation tests. The chemistry of the heterocyclic thioamides is complicated by the fact that they can exist in a number of tautomeric and ionic forms at different pH’s. This is discussed in relation to the flotation and calorimetric data.

Jan 1, 2018

By Ana C. C. Pacheco, Maurício L. Torem

"The aim of this work was the study of the effect of the type (Fe3+, Al3+ and Fe3+ and Al3+ mixture) and of the coprecipitant concentration on As5+ removal by ACF. Removal of As5+ using Sodium Dodecylsulfate (SDS) as a collector was studied by Adsorbing Colloid Flotation (ACF) at laboratory scale. The morphology of the precipitate retained in the foam was analyzed by Scanning Electron Microscopy (SEM/EDS).By comparing the coprecipitant type and concentration studies it could be concluded that As5+ removal in the presence of Fe3+ (160 mg.L-1) alone, or a Fe3+ (80 mg.L-1) and Al3+ (40 mg.L-1) mixture, is equivalently effective (99,9%) and greater than in the presence of Al3+ (80 mg.L-1) alone (97,7%).Through SEM/EDS analyses, it was possible to observe that both morphology and composition of the precipitate produced in the solution and retained in the foam depend on the physico-chemical conditions of the system, that is, on the species present in the solution."

Jan 1, 2003

By L. Y. Feng

The percentage of leached zinc in massive zinc oxide ores (11.7% Zn, >2 mm) is up to 73.3 % in 120 days. Alternatively, crushed to -0.154 mm, mixed with cement 5% (wt), pelletized and solidified. The diameters of the pellets obtained are between 5 mm to 8 mm. When the pellet solidification periods are 3 days, 10 days and 45 days respectively, the alkaline leaching rates of zinc in the pellets are up to 95.8%, 89.1% and 76.4% respectively. Decreasing the solidification time can re-duce reaction time, increase dissolution of zinc in pellets and lower the effect of initial zinc concentration on leaching rate. The experiment results show that the minimum solidification time is three days, and the kinetic study indicates that alkaline leaching of the low grade zinc oxide pellets is controlled by the diffusion of the leach liquor through the gangue layer in the whole leach process, and the apparent rate constants are 3.33×10-2 day-1, 9.18×10-3 day-1, 5.82×10-3 day-1 respectively.

Jan 1, 2014

By Mohan Ram

Structural impurities in the crystal lattice of rock phosphate of Indian origin is a great challenge for beneficiation and practically possesses remote scope of upgradation to the desired level for industrial utilization. There is a wide occurrence of rock phosphate in different parts of India with different characteristics viz. siliceous, carbonaceous and ferruginous. The structural cationic replacement in the composition of apatite is due to the exchangeable cations present in the external impurities associated with the rock phosphate ore. The Indian rock phosphate ore from Purulia district, West Bengal is characterized as unusual structural composition due to the exchangeable cation in its composition. The elemental distribution of ore exhibits the disproportionate ratio of P2O5 and CaO which is 5.88: 3.31 in reference to the theoretical composition of P2O5: CaO in apatite which is 4.23: 5.55. The substitution by trivalent Al+++ cations within the structure of apatite in place of divalent Ca++ is found upto 18% and substitution of exchangeable cation in place of PO4 and F ion by CO3/SO4 is found upto 0.1% and OH ions upto 0.2% respectively in a lattice of apatite thereby diluting the grade of rock phosphate and restricting its industrial use even after beneficiation. This paper reveals the unusual compositional features of rock phosphate under study and is a guideline to the mineral industries using such rock phosphate. Keywords: external impurities, exchangeable cation substitution, structural compositional features, electron probe micro analyzer

Sep 1, 2012

By Chuanyao Sun, Longli Liu, Fayu He, Guiye Wu

Utilizing thioglycolic acid (TGA) as a template and using structure-guided design, a molecular modelling approach has been used to design and screen appropriate dispersant for chalcopyrite. A series of organic dispersants based on a TGA substitution with hydroxyl and amino and sulfonic functional groups have been examined on chalcopyrite surface. 20 organic depressors of chalcopyrite have been investigated to study the quantitative structure-activity relationship (QSAR) of chalcopyrite depressors. For the chalcopyrite surface, depressor containing carboxyl and sulfonic group is generally stronger than the depressor containing hydroxyl group. Increasing the number of hydrophilic group can effectively enhance the inhibition. Increasing the number of Solidophilic group does not necessarily lead to enhanced inhibition ability; steric factor is one of the important factors to affect the interaction. Extension alkyl carbon chain length cannot enhance the interaction of depressors. Isomers principle as well as applies to the chalcopyrite depressor molecular design. Flotation verification tests further confirmes the accuracy of the molecular simulation. Through the Computer Aided Molecular Design (CAMD) technology, we can save enormous time and resources to design novel surfactants. This research and application will play a great significance role in sulfide flotation.

Jan 1, 2014

By A. Y. Senchenko, Y. V. Kulikov

"The most common technique for selection of grinding equipment is the Bond method implying determination of a ball mill work index (BWi). The method is perfect for greenfield projects where a ball mill must be sized to grind an ore to 80% passing 75-100 µm. Finer grinding will require application of specific correction factors to a standard equation since initially the method was not designated for sizing of fine (minus 75 µm) grinding mills. Significant issues are related to selection of grinding equipment for treatment of originally fine materials when the standard procedure is not applicable. In 1984, Levin published his special technique titled as “A proposed test for the determination of the grindability of fine materials”, where he offered to use the standard Bond ball mill for determination of a specific grinding energy. However, this method did not meet with wide recognition. In 2017, Institute TOMS under guidance of JKMRC’s specialists performed a testwork aimed at verification of a new universal technique for determination of grindability of initially fine materials. An object was to test three aged tailings samples for the subsequent modelling of comminution circuit and evaluation of potential throughput of the existing ball mills with final grind size of ?80 passing 53 µm. In parallel with development of the universal approach, TOMS’ specialists carried out tests according to the Levin method in order to compare the data resulted from two methods. The results from lab ball mill testing on three products following the alternative test methods are presented in this paper along with the testing methodology and results analysis. Specific energy was calculated for regrinding of the materials to the required size. Difference of the examined methods and assessment of their applicability for sizing of full-scale equipment are explored."

Jan 1, 2018

By Thomas Mütze, Michael Klichowicz, Mathis Reichert, Holger Lieberwirth

"Self-similarity is proofed to be a common feature when brittle material is comminuted, either in particle bed or single particle mode. Appropriate test work is well documented for particle sizes less than 7 mm in several publications. In contrast, almost no research has been done for coarser particles. The aim of this paper is to show that the fracture pattern of coarser material also tends to be self-similar. Hence, single particles of quartzite, granodiorite and dolomite were comminuted under compressive load. The focus was set on three different size fractions -3.15 +2.5 mm, -31.5 +25 mm and lumps -300 mm. According to the wide range of particle sizes, three different piston-die presses were used with a maximum compressive force ranging from 5 kN to 4000 kN. The force-displacement curves were recorded in order to calculate the specific comminution energy. Additionally, the -31.5 +25 mm size fraction was crushed in a laboratory scale jaw crusher and a roll crusher. Some authors report that the energy-size-reduction relationship of self-similar materials can be approximated by a linear function, which is independent of the comminution equipment. In their charts the slope can be seen as a product-size-independent grindability measure. Our tests show a self-similar breakage behavior when particles in a range of -300 +3 mm are comminuted in single particle mode. Furthermore, the products of the piston-die-presses and the roll crusher are similar to each other in a self-similar representation of the particle size distribution. The jaw crusher product, however, is not self-similar compared to the piston-die-press products. Finally, the linear energy-size-reduction relationships are confirmed for each fraction, but show size dependent slopes."

Jan 1, 2014

By Leon Lorenzen, Trevor J. Britz, Pierre J. Van Zyl, Ellis R. Els

Enhanced granulation of UASB granules was tested on pilot scale with two different test reactors (about 5 litres capacity each). Sludge from a local sewage works was used, with peach cannery effluent as carbon source. Cyclic motion of the reactor contents, and a daily replenishment of feed material create the necessary stress conditions for enhanced growth. Sizable granules, bigger than 0.5 mm, were produced within 20 days. Of the two reactors tested, the reactor equipped with a horizontal agitation shaft proved more effective.

Jan 1, 2003