Search Documents

By A. A. Novoselov, U. Kelm

"Large volumes of mine tailings accumulated in surroundings of porphyry copper deposits represent a growing threat to environment. They contain significant concentrations of toxic metal and metalloids which can contaminate river runoff, ground waters or can be transported by wind. Both extreme pH of fluids in tailings impoundments and high surface areas of processed mineral grains provide their increased reactivity. As a result, during only a few decades, As, Cu, and Mo can be mobilized, redistributed through the tailing column and accumulated through post-deposition leaching, evaporation and contamination with natural fluids. Those processes are reflected in the forming of secondary minerals. Gypsum, Fe oxides/hydroxides, efflorescent salts and clay minerals are typical alteration products in tailings. Here we present the results of reactive transport simulations implemented on the base of PHREEQC and SUTRA codes. The one-dimension model emulates the mass balance between rainfall, evaporation and subsurface runoff, the kinetically- and thermodynamically-driven dissolution of tailing minerals, advective and diffusive transport of tailing fluids, and precipitation of secondary phases. A typical tailing column is composed of four unequal layers with predominance of (i) evaporation, (ii) secondary mineralization above, (iii) below water table, and (iv) near the bottom of dump. Those horizons are characterized by contrasting pH, chemical composition and bulk mineralization of pore fluids, distinct accessibility of atmospheric oxygen and, as a consequence, distinct intensity of sulfide oxidation. The modeling and its verification on Chilean tailings impoundments reveal the complexity and high rates of secondary mineralization. The accumulation of toxic alteration products is controlled by fluid transport through the tailing column induced by both rainfall/evaporation and exchange with subsurface runoff. The geochemical modeling is a powerful approach which allows comparing the processes in tailing deposits produced by distinct flotation regimes and providing the long-term predictions of their environmental impact as well as identifying sectors of tailings for possible re-processing."

Jan 1, 2018

By Heribert F. Broicher, Arne Volland

The application of remote sensing techniques combined with fluorescence spectroscopy is realised in analytical devices called LIF Analysers. The analysis of laser-induced fluorescence facilitates non-destructive, non-contact, on-line and real-time rock identification and quality control of bulk solids in transport. LKAB of Sweden was the first company to test LIF Analysers in the Kiruna Mine for bulk sorting of run-of-mine ores depending on the phosphorus content. Other applications tested in Germany so far are quality control of limestone (iron and/or dolomite content) and rock identification in lignite mining. Of special interest also is rock identification in diamond mines for dilution control. The paper summarises the present state of the application of LIF Analysers.

Jan 1, 2003

By A. Wieniewski

The observed progress in technology of non-ferrous ores enrichment and condition of machines and equipment in the ores concentrators on the one hand have brought a possibility and on the other resulted in necessity for introduction of modernization actions. Positive results of investigations into influence of chemical modification of selected products of enrichment process on copper ores enrichment results gave possibility for implementation of chemical-flotation technologies of ores enrichment. The substantial development in flotation machines structure has contributed to modernization of flotation process resulting in increase of enrichment efficiency. The paper presents the idea and results of chemical modification of difficult in enrichment semi-products in the technology of copper ores enrichment and the results obtained after application of the modernised technology. The structure of large-volume flotation machines used in various stages of flotation and current situation in modernization of flotation process in copper ores concentrators are also described. The paper presents industrial-scale results of flotation after application of modified flotation reagents of collector group. Introduction of modifiers into the widely used xanthates resulted in increase of copper recovery in concentrate.

Jan 1, 2014

By Wenying Liu, Marek Pawlik

Long-chain ionic surfactants, with fatty acids and amines as the most important representatives, are widely used as collectors in froth flotation. These surfactants, generally referred to as weak electrolyte collectors, frequently form solid insoluble precipitates within a certain pH range. However, the action and behavior of these colloidal precipitates in froth flotation systems are not well understood and has not been well decoupled from those of dissolved forms. The objective of this study was to understand and compare the role of colloidal precipitates with that of the dissolved forms at gas-liquid and gas-liquid-solid interfaces. Using primary amine as the model surfactant, experiments were carried out to measure: the maximum volume of bubbles generated in the presence of dissolved and precipitated forms of the surfactant; surface tension for both forms of the surfactant using the drop shape and maximum bubble pressure methods; and contact angle using the sessile drop method. The experimental results showed that: in the presence of the precipitate, bubble volume was smaller, which was correlated with the lower surface tension and higher contact angle measured; the surface tension of solutions containing surfactant precipitate was affected by the surface age of liquid droplets. This study enhances understanding of the interfacial behavior of long-chain ionic surfactants under different conditions, which would help improve the efficiency of reagent utilization in froth flotation.

Jan 1, 2014

By Peter Ay, Elena Geldt, Satyanarayana Narra, Claudia Glaser

"As part of an extensive research and development project, the technical and technological implementation of the patents DE 10 358 245 B4 and WO/2006/056172 was developed with the goal to present a system for the innovative roll- agglomeration method exhibiting a) a modular setup, b) high productivity and c) suitability for the use of fibres of different applications and product qualities (high technical availability). The processability of the rarely adapted raw fibre materials into high-value intermediates brings forward their application in various processing industries dealing with the production of fibre reinforced plastic composites, heat and sound insulation materials as well as with the gas and liquid cleaning systems. The innovative fibre agglomeration presented in this work is performed by a combination of rolling and pressing the fibres inside a geometrically pre-defined roller table, in which the fibres are forced to bound through entanglement / interlocking and develop into agglomerate. The agglomeration process is carried out in a circular roller path with a rectangular cross-section. For improving the adhesive properties, and thus the quality of the agglomerates, the boundary surfaces can be covered / patterned / lined / coated with various materials. The resulting roll-agglomerates are characterized by different quality parameters such as mass, shape, porosity and stability. The properties of the agglomerates can be modified based on the end-product requirements by slightly modifying the process parameters such as filling ratio, residence time, roll-geometry, procurement of the boundary surfaces, etc. as well as the input material properties such as fibre type, fibre fineness, fibre length, etc. This work carries extensive work on the roll-agglomeration system to assess the effectiveness and the variability based on the product specifications. Agglomerates were produced with wide variations of system parameters with varying roller table liners and based on evaluation of the produced agglomerates with respect to their mass, the geometrical dimensions, their porosity and stability."

Jan 1, 2014

By A. Oberrauner

Electrostatic separation is a dry separation technique usable for many applications in the mining- and recycling industries. At the Chair of Mineral Processing intensified research has been done on this topic during the last years. One challenge was to measure the triboelectric charging of fine mineral particles in a triboelectric charging device consisting of an electrically insulated polyethylene rotor/stator assembly. These tests, performed on monomineralic samples, were accomplished in a climate chamber. It was shown that charging of minerals not only depends on rotor speed, feed rate and atmospheric circumstances but also on the properties of the applied electrostatic field. Tests on pure calcite in contact with the polyethylene rotor/stator system resulted in specific triboelectric charges up to +10 nC/g at low relative humidity. With more water present in the surrounding atmosphere, these charging values decreased significantly. However, at higher relative humidity, triboelectric charge values could be maintained after an electrostatic field of positive polarity was applied. Similarly, charging behavior was found with other hydrophilic minerals. The idea behind all these tests was to find the largest charging difference between minerals occurring together in a deposit and to be able to charge them oppositely, assuming that this means good sort ability in an electrostatic separator. The results gained from these investigations are shown. After having obtained many results on charging pure minerals, it became interesting to test the applicability of the charging tendencies on electrostatic separation of fines <100 µm. In order to do so, a separator for fine polymineralic powders was developed, constructed and combined with the triboelectric charging device, all being set up in a climate chamber. This new so-called coax-separator is presented along with first test-results.

Sep 1, 2012

By Gábor Mucsi, József Faitli, Imre Gombköto, Sanjay Kumar, Zoltán Molnár, Balázs Ráczkevi, Ádám Rácz

"Generally, fly ash particles are very fine (< 100 ?m), mainly spherical and glassy materials form an outer shell on it. This paper deals with the laboratory investigation of ground fly ash based geopolymer. This material can be applied in many fields, mainly in the construction industry, e.g. non-structural elements, concrete, pavements and products, containment and immobilization of toxic, hazardous and radioactive wastes, advanced structural tooling and refractory ceramics, and fire resistant composites used in buildings, etc. The preparation of fly ash using high energy density milling is presented. Systematic experimental series were carried out in order to optimize the preparation process. The particle size distribution (LPSA) and structure of fly ash (FTIR) and the uniaxial compressive strength ,the permeability and structure of geopolymer product, furthermore the rheology of geopolymer paste were investigated. The product properties were studied as a function of the fly ash fineness. As a result of the investigation the relationship between the grinding circumstances, the ground material properties and the geopolymer characteristics was identified. It was found that the above mentioned physical properties of the geopolymer strongly depend on the grinding process."

Jan 1, 2014

By K. H. Luo, J. Y. Liu

An experimental study on interparticle breakage of three iron ores was carried out by compressive stressing of particle-bed in a piston-die device. The feeds to the particle-bed stressing were five narrow size fractions in the size range of 0.2~3.2 mm respectively and a wide size fraction of 0/4.0 mm. The pressures applied were in the range between 30 and 360 MPa. The results show that the energy absorption of the particle bed increases linearly with the pressure; the increase of the product fineness with the pressure declines as the pressure goes up; and the product size distributions resulting from interparticle breakage of different narrow size fractions have no self-similarity. Using data obtained from the piston-die compressive stressing test, the suitability of a previously-developed material-characterization model for interparticle breakage was verified for these ores. It is shown that the particle-bed compression test conducted with piston-die device in lab-scale may provide a cost-effective way of studying and modelling size-reduction of ore materials by interparticle breakage.

Jan 1, 2014

By David I. Verrelli, Boris Albijanic

"Froth flotation is an exceedingly complex physicochemical process. The convenience of distilling much of the complexity of the bubble-particle interactions into a single parameter has led to the continuing popularity of the classical ‘induction time’ to quantify the threshold for bubble-particle attachment to occur. Despite this popularity and the simplicity of the concept, there is no single universal method of evaluating the induction period. In this paper, we begin with a critical review of the available techniques for estimating the induction period. These are: back-calculation from experimental (micro) flotation tests; pushing a particle toward a stationary bubble (or vice versa) using an atomic force microscope (AFM); pushing a bubble toward a stationary bed of particles in the ‘Induction Timer’; pushing a bubble toward a stationary solid surface using the ‘integrated thin film drainage apparatus’ (ITFDA); and dropping particles onto a submerged stationary bubble using the ‘Milli-Timer’ device. Each one of these methods has advantages and disadvantages, and the best choice depends on the application. In the experimental section, we present quantitative comparison of the induction periods estimated using two different techniques, namely the Induction Timer and the Milli-Timer. The same particles were tested in each device, under the same conditions. It was found that by tuning the operation of the particle pick-up device, similar estimates of induction period could be obtained to the estimates made by direct observation with the Milli-Timer. In the former device a bubble is driven toward a particle bed at a controlled rate, whereas in the latter a particle’s motion is governed by the hydrodynamics. The potential to match these presents an intriguing prospect for better understanding the bubble-particle interaction, and the possibility to ‘calibrate’ the simpler Induction Timer against direct observations."

Jan 1, 2014

By Narasimha Mangadoddy

The complex nature of multi-phase flow in dense medium cyclones has restricted plant operators and designers to rely on empirical equations for predicting the performance. A number of empirical cyclone models have been developed in the past (Wood, 1990; Dunglison, 2002). In recent years, this subject has been broached with computational fluid dynamics (CFD). Most of the CFD models have not considered the correct rheological behavior of magnetite medium while simulating the medium segregation inside the cyclone. These models mostly predict excessive underflow volumetric flow rates. In this paper simulations of magnetite medium in a dense medium cyclone, were conducted in FLUENT where the particle phases were simulated using the modified Mixture model. The turbulence was resolved using Large Eddy Simulation (LES) model. The rheological behavior of medium was considered in the form of Granular viscosity, Newtonian and Non-Newtonian models corrected with particle loadings and fraction of ultrafines. Multi-phase simulations using granular viscosity option although predict the overall split product medium densities reasonably close to experiments, the mixture viscosity values are restricted to substantially lower values, similar to water viscosity. Simulations using Newtonian viscosity model corrected with particle loading, and fine fraction below 53µm size is predicting overall mixture viscosity levels well over water viscosity levels, but under predicting the under flow the underflow medium density. Multi-phase simulations using Non-Newtonian Herschel-Buckley model, calibrated for superfine magnetite medium measured viscosities, is closely predicting the medium segregation with gamma ray tomography data. Overall predicted product medium densities, underflow volume split are close to the experimental data. This model is can be further used to simulate coal portioning and hence in developing new designs.

Sep 1, 2012

By P. Huang

Chitosan was tested as a depressant in the differential flotation separation of chalcopyrite and galena. The micro-flotation results showed that chitosan selectively depressed chalcopyrite while galena was floated by potassium ethyl xanthate in acidic solutions. With the addition of 0.67 mg/L chitosan (CT) in the slurry of chalcopyrite-galena mixtures at pH 4, the recovery of galena was 95% while that of chalcopyrite was 30%, indicating that chitosan could potentially be used in differential Cu-Pb sulfide separation. Furthermore, the study of chitosan with either low (LCT) or high molecular weight (HCT) in the differential flotation indicated that better separation was achieved by the chitosan with lower molecular weight (LCT). ToF-SIMS was employed to study the distribution of CT on the surface of chalcopyrite-galena mixtures by ion mass spectra analysis and surface imaging, which showed that CT adsorbed heavily on chalcopyrite but barely adsorbed on galena. The positive ion ToF-SIMS spectra provided information on the surface composition of chalcopyrite-galena mixtures after CT treatment. It appears that the selective adsorption of CT on chalcopyrite was originated from the strong interaction between NH3+ and Cu. Keywords: differential flotation, micro-flotation

Sep 1, 2012

By Graeme J. Jameson

"When mineral particles are floated in a mechanical flotation cell, it is found that the rate constant, after reaching a maximum value, starts to decline as particle size increases. It had been thought that the reduction in rate constant had been due to the increased prevalence of composite particles in natural ores, for larger particles. However, Jameson (2012) showed that the rate constant for composites is certainly a function of the surface liberation, but the reduction in flotation rate is independent of particle size. Thus all particles are equally affected by reduced surface liberation, independently of their size. He further argued that the classical peak observed in the rate constant with increasing particle size, is a function of machine hydrodynamics. Thus in mechanical cells, the peak may be due to the high energy dissipation rate and its effects on the detachment of particles from bubbles (Goel and Jameson, 2012). Consequently, in a different flotation environment, it may be possible to float large composite particles that cannot be floated in mechanical cells. This paper describes the flotation of large composite particles in a fluidized bed flotation cell. The particles to be floated are fed to a column in which there is a continuous upflow of liquid. A conventional froth layer of controlled depth is formed at the top of the vessel. A fluidized bed of particles is established which provides a gentle environment for the contacting of large particles with bubbles. An example is given where a porphyry copper ore was prepared at a top size of 710 µm, and floated with conventional collector (PAX) and frother (MIBC). The concentrate was separated into size fractions and examined by photography. Composites were observed at all size fractions, but above 400 µm, all particles were composites. The implications for future flotation circuits will be described."

Jan 1, 2014

By M. Maldonado

A flotation bank is a serial arrangement of cells. How to optimally operate a bank remains a challenge. This article reviews three reported strategies: air profiling, mass-pull (froth velocity) profiling and Peak Air Recovery (PAR) profiling. These are all ways of manipulating the recovery profile down a bank, which may be the property being exploited. Mathematical analysis has shown that a flat cell-by-cell recovery profile maximizes the separation of two floatable minerals for a given target bank recovery when the relative floatability is constant down the bank. Available bank survey data are analyzed with respect to recovery profiling. Possible variations on recovery profile to minimize entrainment are discussed.

Sep 1, 2012

By A. Sand

Within stamp-charged coke making a large volume of coal is compacted to one single coal cake before entering the coke oven chamber. This is done by means of several falling stampers in a stamping machine having a mold nearly of the oven?s dimensions. Producing a high quality coke also from inferior coals requires a cake density of approximately 80% of the coal density. Besides that the industrial stamp-charging process demands a minimum mechanical strength of the coal cake to move it from the stamping mold into the oven chamber without failure. Densification and the build-up of cake strength were investigated earlier in stamping tests using a micro-stamping device. The quantities derived from these tests (as e.g. cake density or porosity) represent average values for the entire cake. Statements describing the local compaction state at different heights are difficult to achieve without destructing the cake. In order to gain better insight into the densification process and the inner structure of the coal cake a computational model based on the discrete element method (DEM) has been set up using 2 and also 3-dimensional simulation software. The stamper?s position and velocity as well as the force acting on the stamper were monitored and the model?s response was compared against measurement data from laboratory stamping tests. It was possible to reproduce the force and displacement pattern of the stamper in response to the viscoelastic properties of the cake using standard DEM bonding and contact models. Furthermore, the rearrangement of particles in response to the compaction by the stamper was tracked by calculating their displacement at the point the stamper hit the coal surface. The latter can also be used as indicators of particle deformation or breakage. By defining control points at different heights the particle displacement, stress and strain rates, porosity could be studied at different heights. Keywords: coke making, coal stamping, compaction, agglomeration, DEM, simulation

Sep 1, 2012

By M. H. Moys, M. M. Bwalya

The use of the Discrete Element Method (DEM) to simulate the interaction of particles in dynamic environments is growing rapidly. This technique is also being applied in the study of milling extensively. However, to date more focus has been on the validation of the model. In spite of the advantages of the detailed information that is available from the simulator, appropriate application of this information remains a daunting task. In this paper a technique that combines particle breakage probability data with the energy spectra generated from the DEM is discussed.

Jan 1, 2003

By H. J. Liang

In this study, zeta potential and contact angle measurements of pyrite before and after interacting with Thiobacillus ferrooxidans are carried out to investigate the changes in its surface properties. The results show that, after pyrite interacting with Thiobacillus ferrooxidans and its metabolite, the surface electricity of pyrite changes obviously, resulting in a notable shifting of isoelectric point to lower pH value, but the contact angle varies little. Bacterial protein plays the most important role in the interaction. This work is helpful to disclose the mechanisms of Thiobacillus ferrooxidans de-pressing pyrite flotability.

Jan 1, 2014

By Grigory Voyloshnikov, Sergey Petrov, Vladimir Petrov

"The treatment of high-grade copper gold-bearing ores is practiced extensively. However, due to low concentration of copper the application of a separate process for copper recovery can make this process uneconomical. The copper, in particular: in oxide minerals, intensively bounds with cyanide during conventional cyanidation. In this case, cyanide is not able to react with precious metals and the consumption of cyanide increases. The resulting copper cyanide complexes have a negative effect on the recovery of gold. Due to decreasing of the process parameters, a repeated use of the recycled solutions can be hindered, especially in the case of heap leaching. The technology of copper removal from the process solutions with simultaneous regeneration of free cyanide from copper-cyanide complex and producing of a saleable high-grade copper concentrate was developed. An important feature of this technology is simplicity, the absence of complex or dangerous operations and the use of common reagents. The choice of equipment depends on the ore treatment option: heap or vat leaching. Also, simpler equipment schemes are available. The studies, tests and industrial practice show that if the concentration of copper can be decreased down to the first numbers of mg per ppm or lower, it is reasonable to maintain the process copper grade in the recycled solutions at 30-50 mg/L. In this case, recycling of cyanide-bearing solutions is unlimited. The regeneration of free cyanide from that of bound with copper and other cyanide complexes is 95-98%. The grade of copper in the concentrate is 55-60%. This technology is an economically competitive option, in particular: with the account of the sales of copper concentrate. The removal of copper has a positive effect on gold recovery, especially during heap leaching. In addition to, this offers significant benefits in reduced costs."

Jan 1, 2014

By I. N. Babich

"Complex technological problems associated with the processing of mineral raw materials require the search and development of new means and ways of thinking. At present, computer cognitive graphics (CCG) are one of the most actively developing areas of new information technologies. The aim of the study was to optimize the cycle of technological evaluation of ores at all stages of geological exploration of deposits on the basis of analysis of geological sampling data using CCG. A new approach has been developed that facilitates optimization of the whole cycle of subsoil exploration. At the gold ore deposit, the results of the geological sampling data were processed by the method of constructing the CCG in the form of a histogram showing the frequency of gold extraction and the average amount of its content. Significant peaks of the metal content in the ore, exceeding the level of the average content in the ore by tens of times, have been revealed. Graphical interpretation of the parameters of mineralization reflects the uneven nature of its variability, which indicates the presence of large, rarely occurs of gold in the ore and the need to conduct studies on a sample of ore of greater mass than for ores with tiny gold. On a sample of 50 kg gold-quartz ore studies were carried out on gravity enrichment. The maximum size found in the gold concentrate was 0.07 mm. In the course of integrated tests in a gravity concentrate, gold particles up to 3 mm in size were found, which predetermined the need to include the operation of gravity before flotation. A new approach to subsoil research is protected by a patent (RU 2620823).The technological problems that arise before the researcher associated with the processing of resistant ores require the exploration and development of new means and ways of thinking. New problematic situations on complex mineral and raw materials objects are practically not amenable to resolution by existing methods. Integration of industrial and information technologies is necessary. At present, computer graphics (CG) is one of the most rapidly developing areas of new information technologies. For example, in scientific research, including in fundamental research, the accent from the illustrative function of CG (the visualization of what is already known) is increasingly shifting towards the use of computer cognitive graphics (CCG) tools (Bashlykov, 2016). The function of the CCG is to obtain a new knowledge with the help of a graphic representation - a cognitive image or at least to promote the intellectual process of the logical acquisition of this knowledge. In this study, cognitive images are used to graphically represent the distribution of valuable components in the bowels of the deposit, characterizing the state of mineral-raw materials."

Jan 1, 2018

By W. S. Eu

Reduction of weathered mineral ores can initiate phase transformation which can affect either their activation or deactivation, subsequently influencing the extent of extraction of desired metals in a leaching reagent. The reduction of ilmenite ores for one occurs as a series of parallel, solid state reactions which at present has no known mechanisms, although the evidence of their effects is abundant. Understanding these reactions may well be the key to uncovering the mechanism of ilmenite activation, hence enabling precise control of its reaction process to maximize yield of TiO2 extraction. However, documenting the solid state reactions in the reduction of ilmenite is challenging due to the ore complexity, the number of simultaneous reactions and the difficulty of capturing critical intermediate reactions and phase transformations during processing. The phase transformations of ilmenite minerals reduced at temperatures up to 850°C were investigated in this study. Mineral transformations were studied in-situ using synchrotron radiation based X-ray powder diffraction with temperature resolved tests. The effect of the extent of reduction and specific mineral transformations were verified by leaching reduced ore with sulphuric acid. The re-sults suggest that transformation of major mineral phases occurs within of specific window of operation and thermal treatment appears to influence the extent of activation and leachability of ilmenite minerals.

Jan 1, 2014

By H. Mengbing, A. Potokin, A. Usov

"Revealed and analyzed in the study are the ways of significant perfection of specific characteristics of the equipment, such as use of high-frequency voltage transformation to create a charger; use of pulse transformers, with core made of materials with high magnetic permeability, in pulse generating circuits; as well as use of special ways to produce voltage pulses with a short front. The experiments have proved the possibility to adapt these technological solutions for electric-pulse installations, and suggested on this base is a strategy of further development and application of electric-pulse technologies. The different applications joint work schemes of voltage sources with two levels voltage and energy in electric pulse technologies are investigated. The possibility of increasing energy efficiency of destruction is shown."

Jan 1, 2014